The ICloud log in screen is dim, and will not respond to any data entry
My IMac wants me to sign in to ICloud, but the screen is slightly dim and will not accept any data
Please click iCloud - Learn how to set up iCloud for instructions on how to setup iCloud.
Similar Messages
-
My ipod screen is white, and will not respond to any actions
My ipod touch screen is white, and will not respond to the home button or the sleep/wake button. The battery never drains all the way, and syncing on itunes doesn't help. I would prefer not to restore it, because i have a lot of information on it. PLEASE HELP!!
The battery has to drain eventually. Be patient. Letting it drain and charging it back up after it goes black should fix this.
-
my iPod nano screen is frozen and will not respond. It shows the song which was playing is paused, but will not resume playing. I have held down all controls, and changed the slide switch, but nothing happens
Hi Goofy Goat,
Welcome to the Apple Support Communities!
It sounds like you have done some great troubleshooting for your iPod nano that is not responding. In this situation, if resetting it did not resolve, I would suggest restoring the iPod back to its factory settings and then sync your content back onto it from iTunes. Please use the following article as a resource for restoring.
Restoring iPod to factory settings
http://support.apple.com/kb/HT1339
Have a great day,
Joe -
Imac 27" Intel Core7 CPU 16 Gig RAM. Screen goes black and will not respond except with a push of power button. Second monitor connected via displayport continues to display fine. Apply Store did full hardware diagnostic and all is fine. Did clean wipe from Mavrick back to Mountain Lion but problem remains. Apple Store can do no more.
I did some more digging, it appears to be a backlight problem only. I can see the screen very dimly if I use a bright flashlight in a very dark room. It also seems to run ok if the brightness is turned down a LOT.
So I'm thinking this is a LED driver board issue or the display itself. I'll open it up and check the connection between the two and see if I can get any more clues. At least I can use it somewhat now by dimming the display significantly... -
My nano blinks the apple logo when plugged into a charger and will not respond to any reset commands, anyone have experiance with this problem?
By a reset, I assume you meaning pressing and holding both the Select (Center) and Menu buttons (or Volume Down and Sleep/Wake buttons on the 6G Nano) long enough for the Apple logo to appear?
What happens if you try to manually place the iPod into Disk Mode? If you can do that, I would recommend connecting the iPod to iTunes and restoring it.
Putting iPod into Disk Mode
B-rock -
My ipad has locked-up, it has frozen while running an app, and will not respond to any button, what do I do?
It simply stays on the same screen image, and does not respond to anything. When I plug it into itunes, there is no indication of its presence.
The ipad's clock has also stopped.
eekTry a reset:
Hold the Sleep and Home button down for about 10 second until you see the Apple logo. -
HT201263 the "connect to itunes" screen is displayed and will not change
The "connect to itunes" screen is displayed and does not change after an update.
Maybe:
Restore loop (being prompted to restore again after a restore successfully completes)
Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
Next try placing in DFU mode and then restoring.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
Then try restoring on another computer.
Last, make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
My music screen has frozen and will not respond to my touch
my 32g iPod touch will not respond to my touch while i am in my music library. i can navigate through my iPod and access my apps, calendar, etc., but as soon as i try to get into my music and browse through it, nothing. it has done this before, but it usually "snaps out of it", and eventually begins to work properly. i purchased this iPod brand new in march 2012, so in my opinion it should not be acting up. anyone have any idea as to what is going on with it?
Try the standard fixes:
- Reset. Nothing is lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Restore from backup
- Restore to factory defaults/new iPod -
Ipod screen is white and will not respond to buttons, nor will it reset. Help!
Can someone please help me? My ipod touch 4th Gen. just froze as I was trying to view information on a Free Music Ap.. Now the screen is white and the buttons do not work, nor will it let me reset it. I connected it to my computer, hoping that Itunes or Apple would cause it to reset but it is still unreponsive. I can't even force it to turn off. Can someone please help?! Thanks in advance!
Let the battery fully drain. After charging for at least an hour try:
iOS: Not responding or does not turn on
If not successful time for an appointment at the Genius Bar of an Apple store. -
The screen on my ipad will not respond. Any suggestions?
When I open the cover it says to slide to unlock. When I try to do this nothing happens.
Try a reset. Hold the Sleep and Home button down for about 10 seconds until you see the Apple logo. Ignore the red slider.
-
When I am on the internet, my screen will suddenly scroll all the way to the bottom and will not respond to any commands. All of the other programs are then affected the same way and you cannot even use the commands at the top of the screen becayse they all scroll to the bottom. After a while, the screen resets by itself. Help.
It sounds like a problem wih the backlight inverter. Usually they just go, instead of on and off.
In a dark room hold a flashlight on the display when it blacks out. If you can see the items on the desktop, it's probably the backlight. -
I downloaded the latest iOS7 to my iPad and then the screen went blank and would not respond. I have tried pressing the two buttons together and briefly get the Apple logo but still can not restart, the logo disappears. I have tried connecting to my iMac to restore the iPad but the device does not show up (I have an old iMac). What else can I do?
You need to be running Snow Leopard 10.6.8 at the very least in order to sync your iPad with iTunes so you could update your Mac, if it can be updated, and if you care to do so.
If that's not an option, you will have to find someone that can restore the device for you with their computer running iTunes or make an appointment at an Apple Store and ask them to restore the device for you.
I hope that you have an iCloud backup, because you will lose everything on the device when it is restored.
Snow Leopard can still be purchased in the U.S. Apple Online Store.
http://store.apple.com/us/product/MC573Z/A/mac-os-x-106-snow-leopard
Also, I would not give up on the reset technique....holding down on the sleep and home buttons at the same time until the Apple logo appears. It takes about 10-15 seconds and sometimes just a little longer to get the logo to appear. -
my ipad screen is black and will not reset and does not come back after restoring, the info is still on internal because i can see it on itunes in the apps catagory it's the display is not working, can see backlight but black...does anyone know how to fix, other than take it to apple.
thanks!The wish list only works on apps you have to pay for. To get it tap the icon of the app you want to save. After it opens at the upper right corner is a box with a arrow. Tap that then tap add to wish list list in the box that opens.
-
Ipod nano 5th gen - works fine when plugged in either to wall or computer and appears to be fully charged but as soon as it is unplugged screen goes blank and will not start - is the battery shot?
Yes, your battery is likely toast and in need of replacement. Not much else for troubleshooting here. Sorry.
B-rock -
Hello, so today I realized that my iPhone with iOS 6 is frozen on the music. I can get back to the home screen but I can't get the music player to work because its frozen on the w's and will not respond to touch. I would be grateful for any help on this.
Hi deamayfield,
Thanks for visiting Apple Support Communities.
If your Music app is unresponsive, try restarting/resetting your iPhone:
iOS: Turning off and on (restarting) and resetting
http://support.apple.com/kb/ht1430
Best,
Jeremy
Maybe you are looking for
-
Restrict creation of sales order for specific customer
Hello All, I want to restrict creation of sales order (of particular sales order type) for specific customer, please let me know how can I do it. Your early reply will be highly appreciated. Thanks & Regards, Mahavir
-
Item category determination during Purchase Requisition creation from APO
Im creating a SNP Purchase Requisition in APO and when it is published to R/3, a Purchase Requisition document is created in R/3. When this PR is created in R/3, I want the Item Category to be determined based on the Material master Special Procur
-
Error:RCVR_DETERMINATION" NO_RECEIVER_CASE_BE
hi all, In my soap-xi-rfc scenario this is the error i am getting in MONI when using .wsdl file from EP <i><SAP:Category>XIServer</SAP:Category> <SAP:Code area="RCVR_DETERMINATION">NO_RECEIVER_CASE_BE</SAP:Code> <SAP:P1 /> <SAP:P2
-
Data Source and Application Component
Dear Experts, I am a beginner of BI and I create a Data Source but I forgot to create an "Application Component" beforehand. Now I create an "Application Component" individually and trying to drug my "Data Source" to the "Application Component", but
-
Custom data within EDI_DC40 Idoc record
Hi! We have the following scenario: flat file->file-adapter->XI 2.0->IDOC->R/3 We now have a situation where we need to fill in custom SNDPRN (Sender Partner Number) into the EDI_DC40 control record of the IDOC in question. I am able to fill in these