The letter "B" is not lighting up

I just purchased an Envy 1030US ultrabook and every key on the backlit keyboard lights up except for the "B" key. From an angle, you can see there are LEDs underneath it, but it is not lit. Is this something can be quickly repaired, or should I return the computer?

The new Apple Maps is an updated icon but is part of the built in apps and NOT available from the app store... the old icon you are seeing that was the icon used to get to Google maps IS the icon for Apple maps now...

Similar Messages

  • My key board Sound while I am writing and the letter S doeS not write in lower caSe

    My key board Sound while I am writing and the letter S doeS not write in lower caSe

    PleaSe reply. I am french, the dictation doeS not underStand my accent

  • How do I send text messages from my Ipod touch?  The "send" button does not light up after typing in the message.

    How do I send text messages from my Ipod touch?  The "send" button does not light up.

    First of all, you need you have at least iOS 5 installed. Second, the person you are texting must have an iDevice with iOS 5 or higher installed. You can´t send messages to an non-iDevice. You´ll also need an Wi-Fi network to send iMessages. Hope it helped!
    Message was edited by: AppleTechTalk1100

  • Why in my FP-TC-120 Module, the red leds are not lighting

    The red indicator leds are not lighting, even if there its no TC conected, what could it happent the software works fine but the leds still turn off

    The red LED's indicate Open Thermocouple detection. However, each channel can be configured for either thermocouple (temperature) or voltage measurements. If a channel is configured for one of the voltage ranges (+/-25, +/-50, +/-100, -20 to +80 mV), Open Thermocouple does not apply so the LED's are deactivated. Use the NI-FieldPoint software to make sure that your channels are in one of the temperature modes and not in voltage mode.
    Regards,
    Aaron

  • Why is the letter p is not working on my iPhone 4s?

    Using the keyboard, the letter "p" does work when the iPhone is held in the vertical position.

    Does the area the p letter is located on work with touch when the keyboard is not there?

  • HT3964 My Macbook air charges intermittently. At times when I connect the power adapter it shows that power is coming in but  says "not charging" and the led light on the power adapter does not light. At other times it charges normally. Any ideas?

    Hey guys,
    I am having problems with charging my mac Air.  Sometimes it charges perfectly but then at times much as it shows that it's getting the power from the charger, it says "not charging" and the led light on the charger does not light up. Any help?
    Rgds,
    Kido-Vj

    That can happen when you are Taxing the system. No Apple supplied AC adapter supplies enough power to both power the system and charge the battery at the same time when the system is under Heavy Load, when you are Taxing the system heavily. At those times it will draw power from both the AC adapter and the battery at the same time. So if it is drawing power from both it can't charge the battery while it is drawing power from it.

  • I am in New Zealand and when I type up a rather long email to send back home, the send button does not light up by the time I finish and I cannot send the email and can't seem to save the message or anything and then as soon as I touch a button, poof, gon

    Can anyone tell me why when I type a very long email, the send button is not highlighted anymore when I am done and I can't send the message? And I can't seem to save the message or anything and as soon as I touch a button, I lose the whole thing. Any suggestions?

    Have you tried typing and saving using Notes or word processing Apps before sending message?

  • I'm still looking for a solution for contrast for the back arrow and the "x" that does not light up unless I roll my cursor across it.

    I have asked this question a couple of weeks ago and have not received any suggestions on how to change it. My back arrow is the same color as the box it resides in, they are both black. The "x" in the tab section does not show until I roll my cursor over it. I would like to know how to change the colors in those areas
    I do have a laptop and it has plenty of contrast in those areas.
    Thanks

    I have asked this question a couple of weeks ago and have not received any suggestions on how to change it. My back arrow is the same color as the box it resides in, they are both black. The "x" in the tab section does not show until I roll my cursor over it. I would like to know how to change the colors in those areas
    I do have a laptop and it has plenty of contrast in those areas.
    Thanks

  • My MacBookAir needs to be charged and the power cord is not lighting or charging

    My MacBook Air needs to be charged so I plugged it in as usual, but the green light on the cord is not on and it is not charging.  I have tried several plugs to no avail.  Does the charging cord wear out???

    You can try upgrading your device software, here is the link with the procedure
    http://www.blackberry.com/btsc/search.do?cmd=displayKC&docType=kc&externalId=KB03621&sliceId=1&docTy...
    If I help you with any inquire, thank you for click kudos in my post.
    If your issue has been solved, please mark the post was solved.

  • The letter "o" will not type either lower case or capitals

    I have a lab full of Intel iMacs and lots of little fingers that randomly hit keys on keyboards (elementary school kids). I have one computer that won't let the key of "o" work.
    I have switched keyboards - so it is computer not keyboard
    I have checked/reset all the shortcut keys
    I have checked/reset all the speech recognition-universal access keys
    Updated Firmware
    Repaired HD
    I would attempt to re-image, but my server connection is not working for deploy studio
    It is all users - and my admin password has an "o" in it so I have been using ARD to control machine
    Any ideas out there??

    Go to the flag up on the right side of the menu bar and select Show Keyboard Viewer: is the o working on the virtual Keyboard?
    In addition to the Restore Default button for Keyboard Shortcuts, there is also a Restore Default button in System Preferences Keyboards > Keyboards > Modifier Keys... that you might want to check.

  • HT1338 when I try to update, I get a message that says none of the selected updates could be saved, you don't have permission?????? help.  I tried to restore my hard drive, but the restore tab does not light up

    I am having problem with updating my software, I get an error that says I do not have permission.  I tried to restore the system but it will not allow me to perform that task either

    Ah! The proverbial missing information. Then, CMD+R and reinstall Lion.

  • My macbook pro will not turn on and the charger is not lighting up

    please help!! my macbook pro will not turn on at all, when i plug in the charger it will not light up at all, it suddenly shut down when i was using it.

    Is there any charge left in the battery?
    Press the button on the left side, near the front edge. If no green lights appear, battery is flat. And if the power brick ain't workin' (by virtue of its pilot light not glowing), then it will remain flat and the computer will not power up. If this is the case, maybe try with another power brick of similar size and see if it charges.
    Else the logic board is toast and pitbull's on the money.
    Either case, my gypsy crystal ball forsees a trip to an Apple Store or a Service Provider in your future...

  • Diminish & expand buttons are not lighting up?

    Hi, just curious if any one has had problems recently with the diminish & expand buttons not lighting up on non specific windows .This has just started happening and I'm not sure what " com........plist " flie to chuck out.
    If any body knows let me know.
    Thanks Raff

    Thanks Dean
    Actually what happens is that the yellow minimize button just turns grey and quits working. Now that I think about it it also has happened with Mail and iCal. It has never happened with iPhoto or iTunes or any other application. There was talk that Safari enhancer may be responsible but, at least in my case, when I removed it the problem did not go away. I have never had the problem with my g-4 eMac, my g-3 iMac, or my g-5 iMac, only the G-4 933.
    As of the last couple of months I have only had the issue with Safari and no other app. Trashing preference files even the finder preference files had no effect. Resetting Safari had no effect. Reinstalling Safari had no effect. There were about 10 other people who reported this issue at the time. I have not heard of it of late until this post appeared.
    This is just one of those "who knows" kind of things. Even one of the Moderators jumped in and tried to help but we still could not find a permanent solution. Maybe one day I will wipe my drive and reinstall from scratch everything except my personal documents and files and see what happens. Right now that is just toooooo much work to solve what is to me a minor annoyance.
    EDIT: I don't know it double clicking on the title bar works or not. Next time it happens I will try it and see. What are your thoughts on this?

  • HT2515 My cam works fine with every program except yahoo.  If I just sign into yahoo or even if I use ichat for yahoo, the webcam button will not highlight up.  How can I fix this and/or what am I doing wrong?

    Hello, my father recently passed (using his ID) and I took over the payments on his mac and took his computer.  I am not that familiar with mac, but am usually computer savy.  However, this one has me stumped.  I have no problem starting the built in cam and it seems to work fine with all other programs I've tried using it with.  However, it will not work with yahoo.  Whether I use normal yahoo messenger or if I try using Yahoo through I chat.  The cam button will not light up, therefore, it is not clickable.  Which ultimately means I cannot use my cam on yahoo, which is something I use 99% of the time compared to other programs.  So why is this happening and what solutions can I take to try and fix this?  The mac I am using is: Mac OS X, Version 10.7.4
    Thank you for any and all help, it is much appreciated. 

    Welcome to Apple Discussions!
    1) If the iTunes preference window is open when you connect your iPod, the iPod will not be recognized by iTunes.
    Also, iPods can work with many iTunes libraries, so that is not the problem here.
    Is all the software on your computer up to date?
    iTunes
    iPod Updater
    Updating iPod's Software
    Does the iPod show up in My Computer when connected to your computer? Does it say Do Not Disconnect?
    Try the steps listed here...
    iPod shows up in Windows but not in iTunes
    If you are going to use your iPod with multiple iTunes libraries (home and school)...
    Using iPod with multiple computers
    2) What part aren't you understanding. Here are a couple of free programs you can use to convert videos...
    MPEG Streamclip
    Videora iPod Converter
    The programs should come with documentation and instructions to convert videos.
    3) You can go to file-->add file to library, file-->add folder to library, or have iTunes open and drag the files into the iTunes library while viewing the library.. You can also import from CDs.
    iTunes needs to be adding the songs to the iPod. You cannot just add the song files to the iPod.
    btabz

  • Problem with Flash-Parameter which include the letter 'E'

    Hi,
    we have embedded our Xcelsius-Dashboards in another 3rd-party-webportal.
    The user opens a dashboard via button in this webportal.
    The OpenDocument-URL contains one Falsh-Variable to control the display
    content according the appropriate user who has calling the dashboard.
    In some cases, the content of this Flash-Variable contains the letter "E".
    In such cases the problem is, that the Letter E will not appear in Xcelsius.
    That means, if we call the dashboard for example with the Flash-Parameter-Value "22E"
    via OpenDocument, in Xcelsius comes the Value without the letter "E" (in the case above "22").
    I also tried to use the hex-code of the letter "e" (%65) but this doesn't work.
    Has anybody a hint for us, how this letter can be sent to Xcelsius via OpenDocument?
    Sincerely
    Edited by: Sebastian Eckes on Apr 26, 2011 12:00 PM

    Check for malware infection. The names of these files really indicate the system is infected.
    Which version of Java client is installed? Especially older versions are very vulnerable against website or email based attacks.
    Since malware infections are very different, detailed support can hardly be given via forums.
    Best greetings from Germany
    Olaf

Maybe you are looking for

  • Custom DLN par file..

    Hi Experts,     I am trying to develop a custom DLN par file. I am using various jsp tag libraries to get the list of the nodes but I am unable to produce the tree hierarchy like expansion and collapsing of the trees if there is any child node for th

  • User Define Fields in  Manual Reconciliation

    Hi,   Can i add user define field in Manual Reconciliation. Please let me know how can i add this user define field in Manual Reconciliation. regards Suresh S

  • Airport express not working properly after upgrade to 10.2.8

    Hi and thanks in advance for your advice. I have searched the forums but didn't see my problem listed. I upgraded her ibook recently. B4 the upgrade, no problem connecting wirelessly to the DSL gateway. My office is in the basement under the steel I-

  • Green Hue when Printing on Epson Stylus Pro 9600

    I have an iMac I've just upgraded to Photoshop CS5 I've downloaded the newest drivers for my Epson Printer I've attempted to print using Adobe 1998, SRGB, and a special ICC profile made just for my printer/type of paper Each time I print my photos ha

  • Print option in  graph

    Hi friends, I am using GFW_PRES_SHOW_MULT fm to create to  graphs .i set a print button in my pf status . The user want to take the print of the graph. Please give some solution for enabling the print functinality Thanks in advance