The lock rotation has turned on I have no idea how there is no icon on the bottom task bar can anyone help please
The lock rotation has turned on I have no idea how there is no icon on the bottom task bar can anyone help please
You have the lock icon towards the top right of the screen next to the battery indicator ? If you do then which iPad do you have ? If it's not the iPad Air 2 then you should have a Settings > General > Use Side Switch To option which controls what the switch on the side of the iPad, above the volume control does - if that is set to 'Lock Rotation' then you use that switch on the side to turn rotation on/off
If there isn't a lock icon at the top right then try a soft-reset and see if that gets the iPad to rotate again : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.
Similar Messages
-
Can anyone tell me how to make cursor smaller after inserting picture so that l can add somethimg right next to it instead of bottom of picture. Meaning the next line is too low
AFAIK, you can't. The nature of TextEdit is that it allows the picture to be treated as a character and adjusts the cursor size for that line.
You need a app that supports transparent overlays. -
Have an ipad 2 and have bought the camera connection kit to use with my flip ultra. However when try to connect ot says there is not enough power to support accessory. Can anyone help please?
If you have ios 5.1.1 the output power is 100ma, on the iOS 5.0.1 the power output is 500ma! This may be the cause?
-
Having upgraded from iPhoto 11 to iPhoto 2.0 (531) it now loads but crashes after a minute or so and none of the buttons work. Can anyone help please.
Hey Ian
That would be correct. because of the nature of your issue, you may find more information by using another one of Apple's support resources.
Contact Apple Support
https://getsupport.apple.com/GetproductgroupList.action
Thank you for using the Apple Support Community.
-Norm G. -
my laptop will not open iTunes, as it just says 'This version of iTunes has not been correctly localised for this language. Please run the English version'. I have not synconised my iPhone 5S or iPad 2 with iTunes for well over a year. I noticed the music which had previously been put into iTunes has dissappeared from my phone and iPad. I also want to remove some movies from my iPad and iPhone and there is no way I can do this without being able to manually sync with the Laptop which is running windows 7. Has anyone else come across this and please can you help? I am no expert in fact I know very little about the Laptop, it is my Husbands baby but he doesn't understand anything to do with Apple including iTunes. I will need any advise explained step by step please.
Hi Shelady,
Try downloading and reinstalling the latest version of iTunes from the first link below. If that doesn't do it, the suggestions in the second article should resolve the installation issue.
Apple - iTunes - Download iTunes Now
http://www.apple.com/itunes/download/
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
http://support.apple.com/kb/HT1923
-Jason -
anyone know how to solve this problem, after downlaod, cannot open i tunes at all.
i have downlaod 5 times, still cant. Can the i phone service centre help with this?
Am from Singapore.Restart Computer.
Refer steps here to delete SC file(s):
Win7/Vista http://support.apple.com/kb/TS2363
WinXP http://support.apple.com/kb/TS1776
Then proceed to repair your QuickTime. START > CONTROL PANEL
WinXP - Add n Remove Programs
Win7/Vista - Programs n Features
highlight QUICKTIME and click CHANGE then REPAIR -
Hey guys,
I am new to LabView and my final year project depends on it! Please help as much as you can!
I am trying to output an arbitrary waveform on an oscilliscope. The shape of the waveform depends on user input parameters like no. of samples, amplitude of each sample and the frequency of desired waveform. Please refer to attached Arbitrary_Wave_Display.vi. In the attached vi, the desired waveform is displayed on the front panel. My project requires that I output this waveform through the analogue output channels of the 2 DAQ2005 cards that I have. When I connect the output of th Arbitrary_Wave.vi to the input of the AO write express vi, there is no output of the oscilliscope. I believe it should be connection problems with regards to while loops and loop conditions. I have also attached my attempted vi.
Please feel free to give some advice. It is greatly appreciated,
Best regards,
TheApprentice of LabViewYou didn't attach any VI and what is the DAQ 2005? I don't know of any NI board with that model number. The analog output functions on the LabVIEW DAQ palette only work with NI boards.
-
Help??
Hello nanowillnotwork
Check out the article below and pick one of them that relates to your issue. What you need to find out is that does the computer as a whole recognize your iPod nano or is it just iTunes.
iPod not appearing in iTunes
http://support.apple.com/kb/ts3716
Regards,
-Norm G. -
Hi Guys When trying to install latest version of Apple software I'm getting error message that Itunes has not been properly installed which is strange as I played ' Take Five' two days ago. Can anyone help please?
Jim HoustonPlease see this post by turingtest2:
-
I have a Bose soundtouch system .Until today I could play my iTunes music through it via air player . .I have just uploaded the latest upgrade from iTunes and now I am unable to connect to the Bose system . Can anyone help please? I can connect via my iPad and by using the Bose app so it is not the Bose at fault
@puebloryan, I realize this thread is a bit old, but I have encountered a similr problem and wondered if you had found a solution. I've been using home sharing from itines on my PCs for years, but two days ago, it suddenly stopped. I can share from my Macs, but not from the ONE PC library where I keep all my tunes. I tried all the usual trouble-shooting measures.
After turning home sharing off on the PC's iTunes, turning it back on and turning some other settings off and on, my Macs and Apple TV could briefly "see" the PC library, but as soon as I try to connect -- the wheel spins for a bit and then the connection vanishes. It's as if they try and then give up.
Since this sounds so similar to your problem, I was hoping you finally found a solution. I am also starting a new thread. Thanks! -
How can i turn my iphone 4s into an ipod touch, the phone has been deactivated and has been recovered, i also do not have a sim card for the phone... can anyone help me.
http://support.apple.com/kb/ht3406
Apple recommended process -
I only have one apple ID and facetime has worked with it before, but now I get the message "Unable to verify email because it is already in use". I have looked ofr a solution but can't find one. can anyone help please?
I spoke with Apple Support this morning and they believe anything MobileMe related is due to the conversion over to iCloud that's taking place.
As for other email clients, check with your host to see if settings have changed on their end. I use inmotionhosting.com and over the weekend the updated their outgoing requirements so that a password authentication is now needed.
Hope that helps get some on the right path to resolving their issues! -
my macbook air has gotten slow this past week i have changed browsers and the beach ball keeps coming up all the time and on a game i play it says the network is slow can anyone help me
Go step by step and test.
Restart the router. Restart the computer.
OS X 10.7 Lion / 10.8. Mountain Lion
http://support.apple.com/kb/PH3915
Start up in Safe Mode.
http://support.apple.com/kb/PH4373
Repair Disk
Steps 1 through 7
http://support.apple.com/kb/PH5836?viewlocale=en_US
Reset SMC.
http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
Increase Disk Space
http://support.apple.com/kb/PH10677?viewlocale=en_US
Best. -
My iMac suddenly has a USB problem. I can connect to drives and printers. I am able to pul info off from drives. When I try to send info to a drive or printer, the connection is lost. All USB ports appear to have the same problem. Can anyone help?
Please do 2-3 SMC and PRAM resets back to back and retest. Also use new cables, they can go bad.
Intel iMac SMC and PRAM resets -
Please help. My entire calendar has vanished! I have no idea how this happened or how to restore it. I have backed up to Icloud in the past, but it was also gone in my PC.
Hi,
Which version of Photoshop Elements are you using? I'm going to assume versio 12 for now.
Perhaps, somehow you have been signed out - that would deactivate that copy.
When you load the editor, does it ask you to sign in?
If so, sign in again and then click on the Licence this software button at the bottom. It will then ask you for your serial number. Enter the serial number and hopefully the trial message should stop being displayed.
Brian
Maybe you are looking for
-
i tunes wont launch, error message 13014. help!!!!!!what does it mean? what do I do?
-
Report Output to be mailed as an attachment-On Schedule
Hi , I have a requirement to develop a oracle report with reportbuilder6i,the report output should be in excel format,needs to be run every monday and has to be mailed to some id [email protected] While converting it to excel output emp.xls using tex
-
When reading my book on iBooks, I encounter duplicate pages for many pages then it skips the pages that should be there so I am missing large parts to chapters, is this a "bug" in the book or app? How can this be fixed?
-
Best way to do analysis of data
I have 18,000 or so records, each marked with a date field, and each recording the elapsed time it took to perform some action, in seconds, as of a particular hour/minute/second. For example: TESTTIME TESTDURATION 7:03:21 2.4 7:03:32
-
Why do I keep getting the error message "insufficient content for edit"?
I'm following a tutorial to create crawling text but when I come to superimpose it onto my video, I get the error message "insufficient content for edit"? The crawling text lasts for 10 seconds. I'm confused