The Macbook with the sleep disorder.

I have had my macbook for about 2 years now. My macbook will not go to sleep. You know how you shut the lid or click sleep the screen would go black and the sleep light would pulsate? My macbook would only turn off the screen for a while and leave the light on (but not pulsating). Few seconds later, it makes a noise (sounds like the CD drive moving) and turns the display on. Yet, if I close the lid. This process continuously happens till I open the lid. Thanks for your help!

slverice wrote:
I have had my macbook for about 2 years now. My macbook will not go to sleep. You know how you shut the lid or click sleep the screen would go black and the sleep light would pulsate? My macbook would only turn off the screen for a while and leave the light on (but not pulsating). Few seconds later, it makes a noise (sounds like the CD drive moving) and turns the display on. Yet, if I close the lid. This process continuously happens till I open the lid. Thanks for your help!
Did you install all firmware updates? If you did, did you install and enable InsomniaX? If not, call AppleCare.

Similar Messages

My macbook isn't powering up and makes a beeping noise in time with the sleep light

Hi There I hope someone can help!!!
I had disconnected the power cable and left the MacBook in sleep mode with the lid shut. When I now go to open my MacBook up, and wait for my system to resume from where I left off the screen doesn't on and the sleep light goes off. when I close the lid the sleep light goes back on as if it is in sleep mode but the same happens when I open it again, no power to the screen.
I order to try get my MacBook working again I tried holding down the power button and switching it back on again but the MacBook now looks as if it is going to power up but the sleep light comes on for about 3 secs and then beeps, then every 4-5 secs constantly the MacBook beeps once in time with the sleep light (to note the sleep light is not following its usual fade on fade off rhythm).
I have tried resetting the SMC using the shift command control option and power button (also this is the only way to stop the beeping and flashing) and when you try and switch on the MacBook if you just press the power button it just follows the same beep with sleep light routine, but if you hold the power button in then the sleep light then flashes quickly about 4-6 times and then starts to beep in time with the flash again.
I will also add I have not reconfigured anything or added any RAM to my MacBook it is still on the standard (manufacturing) configuration as I have been looking about for anyone with similar issues and the main question back seems to be have you changed the RAM, I have also tried resetting teh RAM and the proble still persists.
If someone can help it would be awesome!

Here's the Apple support article on beeps https://support.apple.com/kb/HT1547

TS1365 My Macbook Pro 17" 2.44ghz all of a sudden one day decided to not boot up. When the power button is pressed the sleep light in the front on the latch release turns on and there is a small running sound but it never boots up and the screen never lig

My Macbook Pro 17" 2.44ghz all of a sudden one day decided to not boot up. When the power button is pressed the sleep light in the front on the latch release turns on and there is a small running sound but it never boots up and the screen never lights up. Anyone else have this problem? Any ideas?
I'd love to repair it but not if it'll cost 500 bucks or more to replace the logicboard.
I appreciate any help
Michael

Lao Bo,
yes, you can locate and copy a file from your HD to a USB key using UNIX commands. If you know the exact name of the file which you’re trying to locate, try this:
find / -iname filename -print
This command will search your entire internal disk for the particular filename. If you know that it’s within a particular user account, then you can save search time with this variation:
find /Users/username -iname filename -print
Either variation of this command will print all files found which have the given filename. Presuming that you’re able to identify the correct file, you can copy it to a USB key using the command
cp -p filename_returned_by_find /Volumes/USB_volume
If you’re not sure which volume name your USB key has, this command will show you what the possibilities are:
ls /Volumes
Please let me know if you have any trouble with these commands.

I occasionally have issues waking my macbook pro up from sleep mode and have to restart the computer. The apple store replaced the sleep part but the problem is still there

I occasionally have issues waking my macbook pro up from sleep mode resulting in my need to restart the computer. I dislike all of my programs opening at once when I do get the computer started becasue it slows the cpu down. The apple store replaced the sleep part but the problem is still there. Note: i never had this problem with snow leopard

I'm not certain but my new MBA 13...when in sleep mode comes back on from a black screen when I simply click on the left mouse button. Also, one time I did a SECURE EMPTY TRASH on files that totalled more than 1GB and it took so long that the fan kept increasing in speed so I pressed on the POWER button and the MBA shut...I was able to boot up with no problem. As a rule, I now only do secured erases for trash bin data totalling 500mb or less...anything above that gets a regular erase (dump).

What is the difference between closing your macbook & pressing apple-sleep?

What is the difference between closing your macbook & pressing apple-sleep? My friend aid that it is better to put your computer to sleep by pressing the apple then hitting sleep. I have been just closing it. Is there a difference? Also, is it better to shut your computer down every once and a while. It seems like it gets slow if I just have it sleep after a couple weeks. ALSO, after it has been on sleep every night for a while, my computer has trrouble turning off. I get the problem that says, the application finder has failed to quit try force quitting and try again

None.
There's no particular need to shut down the computer except when traveling or moving the computer.
Whatever other problems you've described have nothing to do with sleeping or shutdown. More likely you need to do some maintenance and/or check that you haven't installed incompatible third-party software.
Kappy's Personal Suggestions for OS X Maintenance
For disk repairs use Disk Utility. For situations DU cannot handle the best third-party utilities are: Disk Warrior; DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible. TechTool Pro provides additional repair options including file repair and recovery, system diagnostics, and disk defragmentation. TechTool Pro 4.5.1 or higher are Intel Mac compatible; Drive Genius is similar to TechTool Pro in terms of the various repair services provided. Versions 1.5.1 or later are Intel Mac compatible.
OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep. Dependence upon third-party utilities to run the periodic maintenance scripts had been significantly reduced in Tiger and Leopard.
OS X automatically defrags files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive. As for virus protection there are few if any such animals affecting OS X. You can protect the computer easily using the freeware Open Source virus protection software ClamXAV. Personally I would avoid most commercial anti-virus software because of their potential for causing problems.
I would also recommend downloading the shareware utility TinkerTool System that you can use for periodic maintenance such as removing old logfiles and archives, clearing caches, etc.
For emergency repairs install the freeware utility Applejack. If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the commandline. Note that presently AppleJack is not compatible with Leopard.
When you install any new system software or updates be sure to repair the hard drive and permissions beforehand. I also recommend booting into safe mode before doing system software updates.
Get an external Firewire drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
1. Retrospect Desktop (Commercial - not yet universal binary)
2. Synchronize! Pro X (Commercial)
3. Synk (Backup, Standard, or Pro)
4. Deja Vu (Shareware)
5. Carbon Copy Cloner (Donationware)
6. SuperDuper! (Commercial)
7. Intego Personal Backup (Commercial)
8. Data Backup (Commercial)
The following utilities can also be used for backup, but cannot create bootable clones:
1. Backup (requires a .Mac account with Apple both to get the software and to use it.)
2. Toast
3. Impression
4. arRSync
Apple's Backup is a full backup tool capable of also backing up across multiple media such as CD/DVD. However, it cannot create bootable backups. It is primarily an "archiving" utility as are the other two.
Impression and Toast are disk image based backups, only. Particularly useful if you need to backup to CD/DVD across multiple media.
Visit The XLab FAQs and read the FAQs on maintenance, optimization, virus protection, and backup and restore.
Additional suggestions will be found in Mac Maintenance Quick Assist.
Referenced software can be found at www.versiontracker.com and www.macupdate.com.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.

HT6150 Single press of Power Button does not put my MacBook Pro to sleep after this update! Do I need to change anything in the settings? Any help please? Thank you!

The title says it all! After installing the new Mavericks update, I cannot put my MacBook Pro to sleep after a single press of the Power Button like before. Does it have something to do with this update or my MacBook Pro? Or do I have to change something in Settings?
Any help would be appreciated.
Thanks!

Send your opinion to Apple.
But remember that there are others.
A moment is a medieval unit of time equal to 1.5 minutes or 1/40 of an hour. This reckoning is derived from the work of Bartholomeus Anglicus, writing in 1240 that each hour was divided into four points, each point into ten moments, each moment into twelve ounces, and each ounce into 47 atoms.
In modern English it usually refers to "a short period of time",[2] the exact length remaining ambiguous.

My Macbook pro, (late 2010) sometimes will sleep and won't wake up. then the sleep light flashes.What's the problem?

My Macbook pro, (late 2010) sometimes will sleep and won't wake up. then the sleep light flashes.What's the problem

Hi I've been following this thread (along with a different one on the same topic). I've been having the same problem with my ibook. I can add that I have no problem with startup. It's just that the screen "goes to sleep" unexpectedly and may operate normally for a few minutes or a few hours at most. Opening and closing the lid or restarting seems to cause it to awaken but then usually for just a few seconds or minutes. If it is connected to another video display that display continues functioning fine even though the computer screen is blank. In addition the desktop is there and visible faintly or if totally blank can be backlit through the apple logo and can be read. I've had my logic board replaced twice under the extended warranty and assumed it was that but now I'm thinking of the reed switch. Apple refuses to consider any further work under warranty as the last repair was in Jan, 06 and they claim only a 90 parts warranty and the machine is from 03. Any thoughts before I cut the wires? I have reset the pmu, run cocktail and disk utility. Other than the sleep issue the machine works fine. thanks Ronda or anyone else who has any ideas... Dave

My MacBook wont turn on but the sleep mode turn on

How to troubleshoot my MacBook only the sleep mode turn on

Yeah, if you're having that many problems, I would either go to an Apple Store or call Apple and demand a new one. Something doesn't sound right with your MacBook at all.

MacBook doesn't sleep when I close the Lid.

Hi Folks,
Im new in this Mac World, finally i got my first Mac. A MacBook 3,1 White with Leopard installed.
I think that there's a problem with it. When I close de lid the Mac doesn't enter in the sleep mode. If it is in the Battery it got in sleep mode after 5-6 minutes, because its the time configured in the System Preferences.
If the power cord is pluged it doesn't got in the sleep mode, never. The monitor shutdowns but the light doesn't blink and when I open the lid I can see that the system doesn't have got in the sleep mode.
Does anyone have this same problem ? Please help!
Thanks in advance,
Fred.

Do you have all the latest firmware updates? Check Software Update.

TS1365 Battery is fully charged. When I first put on my Macbook, screen went blue and nothing happened. Now, there is no fire up when I depress the start button. When I close the lid, the sleep light comes on.

Can somebody help me? When i first turned on my MacBook, it never booted up and ultimately the screen went blank. The battery is fully charged and now when I depress the start-up button, nothing happens. Its worth noting that when I close the lid, the sleep light turns on. Thank you in advance for your help. PMB

hi,
try inserting the cd install to boot on diagnostic
Press D during startup
take an apointment with applestore
regards

I have an Macbook with OS 10.6.8 using Itunes 10.4.1 to sync my Iphone4. The itunes just do not sync my contacts ... No error messages .... nothing ... just do not work ... Does anybody have a clue what is going on ? tks

I have a Macbook with OS 10.6.8 using Itunes 10.4.1 to sync my Iphone4. The itunes do not sync my contacts ... No error messages .... nothing ... just do not work ... However, It is working for apps, calendar and email. Does anybody have a clue what is going on ? tks

There is also an option to reset all data on the device with the next sync.
MJ

Since I installed Lion on my macbook the LED light does not pulse when I close the screen - the sleep function does not work.

Since I installed Lion on my macbook the LED light does not pulse when I close the screen - the sleep function does not work neither when chosen after pressing the button nor chosen in the apple menu..

I have had the same problem but on another forum it was suggested that disabling internet sharing would solve this. This fix seems to work on my machine - why it works I do not understand

On my MacBook with Lion Safari does start, does not react immediately after trying to open it. Installing a new Safari does not help. Removing parts of Safari in the Library did not help. Where can I find and remove all components (LastSession ...)?

How can I reset Safari with all components? On my MacBook with Lion, Safari does not start, does not react immediately after trying to open it. Installing a new Safari does not help. Removing parts of Safari in the Library does not help. Where can I find and remove all components as LastSession and TopSites?

The only way to reinstall Safari on a Mac running v10.7 Lion is to restore OS X using OS X Recovery
Instead of restoring OS X in order to reinstall Safari, try troubleshooting extensions.
From the Safari menu bar click Safari > Preferences then select the Extensions tab. Turn that OFF, quit and relaunch Safari to test.
If that helped, turn one extension on then quit and relaunch Safari to test until you find the incompatible extension then click uninstall.
If it's not an extensions issue, try troubleshooting third party plug-ins.
Back to Safari > Preferences. This time select the Security tab. Deselect: Allow plug-ins. Quit and relaunch Safari to test.
If that made a difference, instructions for troubleshooting plugins here.
If it's not an extension or plug-in issue, delete the cache.
Open a Finder window. From the Finder menu bar click Go > Go to Folder
Type or copy paste the following
~/Library/Caches/com.apple.Safari/Cache.db
Click Go then move the Cache.db file to the Trash.
Quit and relaunch Safari to test.

I share a macbook with my other half and we both use it for our iphones. When syncing using the new software I now have all of her and my contacts on my phone. I don't want her contacts! How do I get rid?

I share a macbook with my other half and we both use it for our iphones. When syncing using the new software I now have all of her and my contacts on my phone. I don't want her contacts! How do I get rid?

Hi,
You have 2 solutions:
1 - You can use 2 differents icloud account
2 - You use the same account but you don't sync yours contacts.
You configure that in Settings > icloud
You activate or desactivate what you want.
Have a nice day.

I have a long-existing iPhone 4s with one apple id and started a job where I received a macbook with another apple id. how do i get my phone to sync with the Mac Pro and secondly how do i get my music on there?

i have a long-existing iPhone 4s with one apple id and started a job where I received a macbook with another apple id. how do i get my phone to sync with the Mac Pro and secondly how do i get my music on there?

No not bothered about sycing apps etc it is all about calendars and maybe notes. IN terms of how its done I just want it the easiest way and preferably so that if an entry is made on one calendar then it populates the other.
Thgius is beacuse I have my work diary on outlok, which I then link with my ical. I want to make sure that information is then shared with her.
Chris

The Macbook with the sleep disorder.

Similar Messages

Maybe you are looking for