The operating system returned error 23(Data error (cyclic redundancy check).)

My Stored Procedures and Jobs Showing this Error. Even though i can able to access the data throgh SSMS in Database Engine.Please help on this.
Executed as user: RMS\Administrator. The operating system returned error 23(Data error (cyclic redundancy check).) to SQL Server during a read at offset 0x000006684a2000 in file 'F:\RMSLiveData\RMS.mdf'. Additional messages in the SQL Server error log and
system event log may provide more detail. This is a severe system-level error condition that threatens database integrity and must be corrected immediately. Complete a full database consistency check (DBCC CHECKDB). This error can be caused by many factors;
for more information, see SQL Server Books Online. [SQLSTATE HY000] (Error 823). The step failed.
Thanks
RehaanKhan. M

DBCCCHECKDB('DBNAME',REPAIR_ALLOW_DATA_LOSS)
For crying out loud! Don't you have any shame!
There are situations where you may have to run DBCC CHECKDB with the option REPAIR_ALLOW_DATA_LOSS, but it is not the first thing you shold try if the database seems to be corrupt. Particularly, you should first make sure that you work on a copy of the database
files. REPAIR_ALLOW_DATA_LOSS means that DBCC CHECKDB has carte blanche to throw all pages it can piece together - which could be about all data pages if it is that bad.
Corruption siuations are very difficult to assist with in forums, because there can be a lot of stake. The only advice I can give is to restore the database from a clean backup. If you don't have a clean backup, you have a problem. The database may still
be saved, but you need an expert on site to help you, if you have never worked with this before. Advice given in this forum applied haphazardly can result in more damage that you already have.
But, oh, one thing: this type of corruption are always due to hardware errors like bad disks or bad memory sticks. So just restoring the database is not enough. Finding new hardware is important too.
Erland Sommarskog, SQL Server MVP, [email protected]
Actually on the same disk there are other Databases Stored and they work Properly and Backup also can be taken for that Databases. But, for this particular database only this error is happening when iam trying to take backup. But data retrieval and access to
front end application happening as usual. Please help on this.
RehaanKhan. M

Similar Messages

The operating system returned error 170(The requested resource is in use)

Hello Experts,
We have a Sharepoint farm where we are receiving OS Error 170 for many days. It results in database shutdown/Start because required transaction file is not available.
The operating system returned error 170(The requested resource is in use.) to SQL Server during a write at offset 0x0000029495e000 in file 'F:\MSSQL10_50.INST1\MSSQL\DATA\****.***. Additional messages in the SQL
Server error log and system event log may provide more detail. This is a severe system-level error condition that threatens database integrity and must be corrected immediately
Write error during log flush.
Error: 9001, Severity: 21, State: 4.
The log for database 'DBNAME' is not available
We have checked the Anti Virus but all data files are excluded. We have also disabled the anti virus for some time but still issue persist.
This is a Virtual Machine and no VM snapshot backup is running during the time window.
Please help!
Thanks in advance.
Regards,
Divesh Mathur

Hello Experts,
We have a Sharepoint farm where we are receiving OS Error 170 for many days. It results in database shutdown/Start because required transaction file is not available.
The operating system returned error 170(The requested resource is in use.) to SQL Server during a write at offset 0x0000029495e000 in file 'F:\MSSQL10_50.INST1\MSSQL\DATA\****.***. Additional messages in the SQL
Server error log and system event log may provide more detail. This is a severe system-level error condition that threatens database integrity and must be corrected immediately
Write error during log flush.
Error: 9001, Severity: 21, State: 4.
The log for database 'DBNAME' is not available
Hello,
I sense a disk issue here( I am not sure).Log for database is not available seems when data needs to be written on log file it was not avaialble.Can you check with storage team that disk on which SQL server files reside is OK
Secondly did you run DBCC CHECKDB for your database in picture can you paste result of it.
Please mark this reply as the answer or vote as helpful, as appropriate, to make it useful for other readers

[823] [HY000] [Microsoft][ODBC SQL Server Driver][SQL Server]The operating system returned error 1450(Insufficient system resources exist to complete the requested service.) to SQL Server.

Hi,
I am facing an issue while loading fresh data into SQL server database.
we are able to load data into staging area, but while processing stored procedures system face bellow error message :
[823] [HY000] [Microsoft][ODBC SQL Server Driver][SQL Server]The operating system returned error 1450(Insufficient system resources exist to complete the requested service.) to SQL Server during a write at offset 0x00000243bd0000 in file 'E:\SQLDB\DBName.mdf'.
Additional messages in the SQL Server error log and system event log may provide more detail. This is a severe system-level error condition that threatens database integrity and must be corrected immediately. Complete a full database consistency check (DBCC
CHECKDB). This error can be caused by many factors; for more information, see SQL Server Books Online.
we use windows 2008 R2 with SQL server managment studio 2008.
Appreciate your suggestion.
Thanks in advance.
Best Regards,
Manorath
Manorath

Hi Manorath,
Based on my research, this issue can be occurred in the following scenarios:
You are running a DBCC command on a large database. For example, you are running the DBCC CHECKDB statement on the database. At the same time, you run many DML statements on the database.
You create a database snapshot for a large database. At the same time, you are running many DML statements on the database.
In these scenarios, the SQL Server service stops responding. The DBCC CHECK statement is never completed, and you receive the error message repeatedly.
This issue occurs because the sparse file for a database snapshot file has exceeded the file size limitation in NTFS file system. When the operating system error 1450 occurs, SQL Server enters an infinite retry loop.
To fix this issue, please download and install Cumulative update package 1 for SQL Server 2008 Service Pack 1. Besides, because the fixes are cumulative, each new release contains all the hotfixes and all the security fixes that were included with the previous
SQL Server 2008 fix release. We recommend that you consider applying the most recent fix release that contains this hotfix.
Reference:
http://support.microsoft.com/kb/967164
Thanks,
Katherine Xiong
Katherine Xiong
TechNet Community Support

The Operating System returned Error 27(The drive cannot find the sector requested.)

On a Windows 2008 R2 server running SQL 2008 Standard on a Raid 5, when performing a backup on the databases via copy to another local drive I receive and The operating system returned error 27(The drive cannot find the sector requested.) to SQL Server during
a write at offset 0x0000002fd204000 in the file F:\SQLDATA\Email_Images.mdf. The server is a HP DL380p Gen8. I've contacted HP thinking this was a Hardware issue but HP ensure me its not and to contract Microsoft support.

Hi,
Unfortunately, the available information is not enough to have a clear view of the occurred behavior. Please offer us what backup method you are using, did you want to backup
the data to the CSV, the origional error you have got.
1. The best method would be to have separate disk drive for each cluster SQL instance and add the disk to the specific SQL group and add it to the dependency of the SQL resource.
There would be less overhead with this process other than having to create two disks, one of each instance
2. You could consider creating a file sharing resource on cluster and add the backup disk to this resource group and use it to back up the databases of both the instances
to single disk. The down side of this method would be, all the databases backups will fail if the fileshare resource goes down. You cannot use GUI to take the backup, need additional setup/maintenance for the fileshare resource group
http://support.microsoft.com/kb/224967
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

The operating system returned error 21(failed to retrieve text for this error. Reason: 15105

Hello everybody,
I have a huge database over windows 2003 server and sql server 2008 r2, all of them with all update, no firewall, no antivirus, no any server feature/role installed.
Over the last 2 months I suddently start getting the following error:
The operating system returned error 21(failed to retrieve text for this error. Reason: 15105) to SQL Server during a read at offset 0x000000000da000 in file 'S:\TempDB\tempdb.mdf'. Additional
messages in the SQL Server error log and system event log may provide more detail. This is a severe system-level error condition that threatens database integrity and must be corrected immediately. Complete a full database consistency check (DBCC CHECKDB).
This error can be caused by many factors; for more information, see SQL Server Books Online.
I have the TEMP database split over 5 partitions on 5 different SAN disk. beggining size of each partition fix to 20 GB with autogrow 10%. Single Instance, around 15 DB.
The space on each hard disk does not reach 60%.
I got the above error when all temp files reach 27 GB approx.
I already ran a check disk, checkDB and everything says no error found, but I still got same error.
Does anyone know what could cause something like this?
note, when getting the above error, the only way to fix it, because I cannot do any select on any DB is to restart the service, so each temp file start again at 20 GB and everythign seems to be fine until reach the size again.
Gilberto H.

The operating system returned error 21(failed to retrieve text for this error. Reason: 15105
Hello Gilberto,
See System Error Codes (0-499) for error code 21:
ERROR_NOT_READY
21 (0x15)
The device is not ready.
Could be an issue with your storage system
Olaf Helper
[ Blog] [ Xing] [ MVP]

I just got my iPhone 4 finger tips (CDMA) how do I know if the operating system is up to date?

I just got my iPhone 4 finger tip (CDMA) How do I know if the operating system is up to date?

Check Settings > General > About. Latest version for the CDMA phone is 4.2.10
Stedman

Boot Camp error when installing XP - cyclic redundancy check

I am trying to install Windows XP through boot camp and I have tried settting up using NTFS or FAT and when it go to the XP installation screen I kept getting an error: Data Error (cyclic redundancy check).
Does anyone know if there is anyway to solve this issue?

Yeah, cray-z is right. Check that boot sector anti virus is turned off. If that is not the problem check your h/d jumper settings or try loading the default bios settings, and if still no luck write zeros to the first 50 (I think and I will probably be corrected) sectors in your hard drive. I had the same problem and when I called western digital these where the steps the customer service guy told me to follow.

I am unable to download the programs onto my laptop. I keep getting a message that says the operating system no longer supports the programs.

I need help, i am not sure what operating system needs to be installed. I have a mac and the operating system is up to date.

Creative Cloud programs are not spec'd to work with Mac OS X 10.6.8. You would have to upgrade to at least version 10.7. You should check the system requirements for all of the programs you wish to install to see what the minimum is that would cover all of them. Just Google "InDesign system requirements" to find them for InDesign, and repeat for the other programs using their names instead of InDesign.

Unexpected error from the Operating System

Hello everyone. I have a PCI 1200 board and I use LabWindows/CVI. I want to
make a scan on an analog input channel of my board. For this, I tried the
functions Lab_ISCAN_Op, nidaqAIScanOp and DAQ_Op, and for all of them, the
same error occurs, which is:
return value == -10856
with the message:
osError: An unexpected error occured from the operating system while performing
the given operation.
Any hints for me?
Thanks in advance.
Yves

I have similar problem with Error code= --10452 (noIntAvailError: No
interrupt level is available for use) when I used the Dap_Op() function.
After checking the system's resources (from Control Panel -> System and
click on properties to get the system resources used by my Lab-PC-1200 card.
Win98 has plug and play and so it shows me only the I/O ranges. I forced
the system to allow the Lab-PC card to use IRQ=3 and DMA=5. This resolve my
problem and no more Daq_Op() error messages. I hope this will help. Jack
Sent via Deja.com http://www.deja.com/
Before you buy.

Error: The Operating system Windows Vista Version 6.1 is not supported

While installing Oracle Database 'win64_11gR1_database_11070' on Windows Server 2008 R2,x64, I get this error during Product specific pre-requisite checks:
"The Operating system Windows Vista Version 6.1 is not supported. Install the recommended service pack"
Edited by: aa100 on 16-Jun-2010 09:04

What's not clear with this message? Windows 2008 R2 requires 11gR2:
http://www.oracle.com/technology/software/products/database/oracle11g/112010_win64soft.html
Werner

BDD 2007 -- ZTI -- OSD error "The Operating System Installation Failed Unspecified Error (80004005)

Hi there
Wonder if anyone can advise me on a BDD 2007 OS deployment issue? (Apologies if this is in the wrong forum, I couldn't see a forum for BDD 2007.)
First of all, this BDD 2007 server and the OSD config was not done by me. For info, it is part of a SMS 2003 infrastructure.
I am trying to get the XP Pro build process working. I am led to believe the config has been completed.
Unfortunately, after booting the pc from the nic, I get an error. This is the order:
- the 'Initializing Windows PE' splash appears for perhaps 15 seconds
- very briefly, the text changes to 'Initializing Network'
- for a second or two only 'Initializing Windows PE' appears again
- then this error message appears:
"SMS Operating System Deployment - The Operating System Installation failed. Please contact your system administrator for assistance. Unspecified Error (80004005)"
I've spent some time looking into this error (80004005) and from what I can gather it possibly means 'access denied'.
I'm assuming after Windows PE loads the first Task Sequence begins, and if this possibly is where the issue lies?
One thing I cannot understand - the first Task Sequence (Initialization) has this command line (as do most, with different .wsf file):
cscript.exe "%SCRIPTROOT%\ZTIGather.wsf" /localonly
However, I cannot access %SCRIPTROOT% at all, Windows says it can't find it. I can run other variables such as %USERPROFILE%, %SYSTEMROOT%, etc, but cannot open %SCRIPTROOT%.
Is it simply the case that I should create a new system variable (that has not been created by whoever built the server)?
Thanks
John Henry

Since no one has answer this post, I recommend opening a support case with CSS as they can work with you to solve this problem.
Garth Jones | My blogs: Enhansoft and
Old Blog site | Twitter:
@GarthMJ

Error -2147024714 : Automation Error the operating system cannot run %1'

Post Author: greg.thompson
CA Forum: General
After installing Crystal Reports 10 Pro, I am receiving the following Business Objects error "Error -2147024714 : Automation Error the operating system cannot run %1" While trying to run reports within Business Objects 6.5 SP 2 HF 932, The desktop O/S XP Pro w/sp 2. Tried uninstalling both, reinstalling twice did not solve the problem. I switched the install order the second time, also used all default install locations, any ideas here.

Post Author: greg.thompson
CA Forum: General
After installing Crystal Reports 10 Pro, I am receiving the following Business Objects error "Error -2147024714 : Automation Error the operating system cannot run %1" While trying to run reports within Business Objects 6.5 SP 2 HF 932, The desktop O/S XP Pro w/sp 2. Tried uninstalling both, reinstalling twice did not solve the problem. I switched the install order the second time, also used all default install locations, any ideas here.

MP has rejected a policy request from GUID:27935EC8-95F1-4104-A613-E72D2A9764E0 because it was not approved. The operating system reported error 2147942405: Access is denied.

Why Microsoft doesn't have correct fix to run automatically. How many years we need to cry with same error again n again?
Does any one have correct solution which will fix permanently while running more than 4000 systems in our environment
Manual stuff isn't easy. Pls provide permanent fix?
MP has rejected a policy request from GUID:27935EC8-95F1-4104-A613-E72D2A9764E0 because it was not approved. The operating system reported error 2147942405: Access is denied.

This isn't a bug to fix. This is by design. Clients must be approved to be managed. Thus, only your configuration or expectations must be fixed. To correct your configuration, see the link Henrik posted. To correct your expectations, read the content linked
by Henrik.
Jason | http://blog.configmgrftw.com

Two days ago, I loaded Light Room 6. Today I went back to Light Room 5. LR 6 corrupted an entire folder of images, and caused errors on my Raid 5 causing win 7 to run "Chk Dsk" and fix the errors to the operating system. LR 5 has not shut down for the las

Two days ago, I loaded Light Room 6. Today I went back to Light Room 5. LR 6 corrupted an entire folder of images, and caused errors on my Raid 5 causing win 7 to run "Chk Dsk" and fix the errors to the operating system. LR 5 has not shut down for the last 5 hours. LR 6 has a serious bug. Anyone else experiencing this problem. Yesterday I was on tech support, waiting for 3 hours, finally they picked up and informed me there department was closing and someone else would call me on Monday. So, I'm working today and all day Sunday to make up for the down time using LR 6.
I don't know if the bug exists in the program or the "Creative Cloud.
Question: Does anyone know why if I bought Light Room 6 [NOT Light Room CC with the monthly rental], I have to enter my serial number if I want to use it?

Entering the serial number is probably part of the registration process.
Just out of curiosity, what were you doing on LR6 when the folder of images became corrupted?

Why am I suddenly getting the following error message: "The specified location is reserved by the operating system and is not permitted. Please choose a different location." I've been recording all night and I haven't changed any of the parameters.

Why am I suddenly getting the following error message: "The specified location is reserved by the operating system and is not permitted. Please choose a different location." I've been recording all night and I haven't changed any of the parameters.

Hi Tom,
Looks like we have problem here as we see another blank post from you here. It's probably something to do with your email. Let me send you a PM with my email address and we can communicate that way.
Thanks,
Kevin

The operating system returned error 23(Data error (cyclic redundancy check).)

Similar Messages

Maybe you are looking for