The power button on my nano6 is not working. What should I do?
My nano works fine when it is plugged into my computer but when it's not I can't get it to turn on. It's like the button is broken/disconnected.
Hello courtPG
If the button is not working, then you may want to look at getting service on it as it is something that cannot be fixed easily. Check out the article below for all information on setting that up and any other questions that go along with it.
Service Answer Center – iPod
http://support.apple.com/kb/index?page=servicefaq&geo=United_States&product=ipod
Regards,
-Norm G.
Similar Messages
-
The left speaker of my iphone is not working, what should i do?
the left speaker of my iphone is not working, what should i do?
There is no "left speaker". It's a microphone... Try looking at the manual.
-
The sound on my Iphone 4s is not working. what should I do to fix it?
So randomly the sound on my iphone will not work. Sometimes it will work for short periods of time but then the sound bar will disappear and i'm not sure why...help please!
It sons silly but check the little button above the volume buttons on the side and make sure you can't see orange... If you can, flip it.... And the sound will work. Took me hours to figure that one out....
-
The music buttons in the control centre are not working ,What should i do to get them working
the soft music buttons in control centre are not working,
what should i do to get them workingTry trashing apple.com.dashboard.plist from preference library and restarting Mac.
Quit all applications.
Open Finder- Click the left most icon on the Dock.
Holding option key click the Go menu from the menu bar.
Select Library and then Preference folder.
Select apple.com.dashboard.plist and move it to trash.
Restart Mac. -
My Mac Mini was not sending a signal to the monitor. I powered down using the power button and now it will not start. When i power up I get a strange 2 tone sound, like a warning alarm. The fan starts, and the light comes on, but no screen.
I have tried with a wired USB keyboard and mouse using a single screen. Powered up with option pressed. No change.
Reset SMC no changeRun the Apple hardware test to see what it tells you. Run the extended test when prompted, which can take awhile.
-
My Ipad 2 will not power on. I have tried the two button approach but it did not work. Until last evening, the Ipad was working very well. After it entered the sleep mode, it would not come back on. What can I do?
The first thing to suspect is a completely drained battery. When this happens the iPad shuts down and will not turn on. Even if you charge the iPad it may take more than 30 minutes before it responds. Plug the iPad into the charger that came with it and plug the charger into a known good wall outlet. Do not charge the iPad by connecting it to a computer. Wait 30 minutes. Then reset the iPad. Press and hold both the Home button and the Sleep/Wake button continuously until the Apple logo appears. Then release the button and let the device restart. You will not lose data doing this. It's like a computer reboot.
If the iPad restarts let it continue to charge until the battery is at 100%. If the iPad does not restart consider making an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support. -
purchased Lion, installed it - once I log in - i get the curtain and message to hold the power button till it shuts down. Worked with the disk repair utility - fixed permissions to hold the power button till it shuts down. Worked with the disk repair utility - fixed permissions - still can't get past the "black curtain of death" any suggestions?
My machine was patched to date 10.x.x. I was lucky to get an internet connection and I selected the option to re-download Lion... its curruently being downloaded. What if that doesn't work?
Any thougths would be appreciated.
JoeAnd you have a workstation? not a notebook.
Usually a driver or hardware, nothing that Disk utility will fix.
You know of course what a Prohititory Sign is?
prohibitory sign, kernel panic
Forum devoted to Lion:
Mac OS X v10.7 Lion Communities
Tips and FAQs
FAQ kernelpanic
Resolving Kernel Panics
Avoiding eliminating Kernel panics
Lion App Compatibility Table - RoaringApps
RoaringApps Mac OS X Lion Application Compatibility
did you make sure your apps, drivers, and hardware support Lion? -
my iPod touch isn't working correctly.it is displaying a white light and no matter what i try it isn't helping.tries holding the reset and power button together and tryed holding the power button in but it doesn't work. please can someone help?
Try the remaining items in the white-screen topic of.
iPod touch: Hardware troubleshooting
If not successful. let the battery fully drain and then charfe for an hour and try again.
Frequently a white scree nis due to a hardware problem. -
The return button on my macbook is not working, any suggestions?
the return button on my macbook is not working, any suggestions?
By the way, if you are still interested, I found a solution. It's a bit crazy, but basically I have insulated the parts of the keyboard connector corresponding to the power button using some thin tape and then used a very thin wire going from the logicboard (where the test pads for startup are located) to my eject key, this way the original power button does not respond anymore and the eject key can be used as the power button, just like in the new Airs
I can provide photos if you want. -
My power button on my iphone is not working. What can i do about that?
my power button on my iphone is not working. What can i do about that?
Meaning that you cannot restart or reset the phone? If you haven't tried already, try both options.
Otherwise, you can do a backup & restore, or even a restore as new (only after a successful backup).
If the issue persists, then look at a replacement. Either it will be a hardware defect (free if within warranty), or physical damage ($49 with AppleCare Plus, $149 without it.) -
How do I reject incoming calls on Ios7 when locked? Power button on top right does not work.
I am also facing the same issues. Sometime i get an option to reject call and sometime i won't .
Tried all the basic troubleshooting i could from my end but nogo. Also tried complete reset by loosing data still the same results. Any suggestions and fix, Apple ??? -
i updated to iOS 5.1 but my camera buttone form the lock screen is not working what should i do. i tryed restoring but it didnt work .
When i try the camera loncher but it's not workingi feel stupid now because i didnt know to swipe it up lol
thanks -
My phone died last night and when I plugged it in it wouldn't turn on.I tried restarting it but it has yet to turn on since last night,It was just a black screen,i try the on/off and home buttons together but its not working,What should I do?
How long have you had your phone? Because if you've had it a long time, the battery in the phone might of died on you. Or have you dropped it in water, snow, from high up? All those things could of disconnected something internally in your phone, or permentaly damaged the internal hard drive its self, or the sims card.
-
The home button of my iPod is not working and it got 1 year of warranty and going to Apple store, my iPod is silver color. if they give me a new one can I pick another color ?
No, they will give you a refurbished (but basically a brand-new) iPod touch in the same color. I have the Silver as well...sort of kicking myself for not waiting for the Blue one to come back in stock.
-
My iphone5c is still under the 1 year warranty, the top button constantly sticks and does not work properly will Apple still replace my phone even though there is a few chips and scratches on the back?
As Peter says above, only an Apple Store genius can advise you.
But to further clarify, you seem to postulate that if Apple helps you, the cure would be a replacement. That is not necessarily true. Let them look at it and advise you what the remedy is. They may offer you nothing (saying it's your fault), or they may offer you a solution (keeping your current iPhone), or possibly a replacement.
Maybe you are looking for
-
Hi, I am unable to update the Business Area . I have some blank Busines Areas i should update the Business Area line items same as According to the belnr(header) REPORT zfir_vendorwise_grir_balances NO STANDARD PAGE HEADING L
-
NoSuchMethod when deploying Queue2Topic sample process in 10.1.2.0.2
I have deployed this tutorial process before on another 10.1.2.0.2 system with no problems. However, on this particular BPEL PM, the deployment works fine but errors appear in the domain.log as it tries to activate the JCA agent. The error is as foll
-
I am putting together a photobook. When I format it for 8'x10 hardcover some of the photos come up with a warning of low resolution. Is there anyway to preview how the pictures will print so I can figure if they are acceptable? Is there anything I
-
I have a CSS styled menu on website that worked perfectly fine in IE 6, but doesn't work at all in IE 7. heres the code: any suggestions?
-
Error in PSA after running process chain
Hello All, I have ran a process chain, which came back with an error. I have checked the PSA and there is one line which has an error. How can I resolve it and reload the data into the cube succesfully? Is there away to delete the data from the PS