The shutter for my front camera doesn't open. Help!

My ipod broke,but then we got it fixed and it doesn't work now. I've tried everything that everyone told me to do to fix it.

Hi janaína,
Thanks for visiting Apple Support Communities.
If you haven't already, the next troubleshooting step to recommend is backing up and restoring your iPhone:
iTunes: Restoring iOS software
http://support.apple.com/kb/HT1414
Best,
Jeremy

Similar Messages

  • IPod 4g: the accumulator does not load, camera doesn' t open, reset done but still defect, what can I do?

    I can't load the accumulator, the camera does not open the lens. The cable is not defekt. iPod does not recognise when electric- cable is pluged.

    I think load the accumulator means charge the iPod.
    Not Charge
    - See:      
    iPod touch: Hardware troubleshooting
    - Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar      
    Also:
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • The icon  for PHOTOSHOP 64-BIT DOESN'T OPEN ANYMORE. I GET A MESSAGE THAT SAYS IT CAN NOT BE FOUND IN THE DYNAMIC LIBRARY.

    THE PHOTOSHOP ICON 64-BIT DOESN'T OPEN ANYMORE THE PROGRAM. I GET A MESSAGE THAT IT CAN NOT BE FOUND IN THE DYNAMIC LIBRARY. WHAT TO DO TO RESTORE IT AND OPEN THE PROGRAM?

    Urazurrutia which operating system are you using?  I would recommend removing and reinstalling Photoshop to restore the application.  What specific version of Photoshop are you facing difficulties with?

  • My ipad front camera doesn't working,cannot take a picture this moment,how to fix this problem?

    My ipad front camera doesn't working,cannot take a picture this moment,how to fix this problem?

    Try closing the Camera app via the taskbar and see if it works when you re-open the app : from the home screen (i.e. not with the Camera app 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Camera app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
    If that doesn't work then try a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

  • I have an iPad two and my front camera doesn't work I have tried resetting it Clicking it twice nothing works can you please help me!!??

    I have an iPad two and my front camera doesn't work I have tried resetting it Clicking it twice nothing works can you please help me!!??

    Try closing the Camera app:
    1. Double-click the Home button to reveal the Task Bar
    2. Hold down the Camera app for a second or two until you see the minus sign
    3. Tap the minus sign to close app
    4. Tap area above Task Bar to return to Home screen
    If the above doesn't solve the problem, do a reset:
    Hold the Sleep and Home button down for about 10 seconds until you see the Apple logo. Ignore the red slider

  • Front camera doesn't work! Battery dies super fast!

    Hello! I received my ipod touch 5th generation as a bday gift in November 2012 and I'm having a couple of issues with it. First the battery dies really fast. I have wifi on all the time and I dunno if this is the issue, but using music playback for about 4-5 hrs/day and reading/instagram/fb/WWF for like 1-2 hrs, it lasts about 15 - 20 hrs. I think there has to be a problem because my touch 3rd gen lasted longer basically doing the same thing. And if I play a video for <1hr, the battery lasts less than 12 hrs. That's one thing. Also, a couple of times both the front and back camera have frozen up, and for about a week now, the front camera doesn't work. When I switch to it, it closes up as if it's taking a picture, but it never opens up again, it just stays there. This is for video and camera. The front one just doesnt work. PLEASE HELP! I'm obssesed with this thing and I'm really disappointed by these features. I dunno what to do. And the worst is that after I try to switch to the front camera, I can't switch back. I have to restart the ipod to be able to use the back camera, because it just doesn't do anything. 

    For the camera problem
    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up           
    - Restore to factory settings/new iOS device.
    -  Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar
    The battery life you are getting is normal and expected. If you have a concern after doing the above make an appointment at the Genius Bar.

  • Iphone 5c front cam doesn't work...

    hey, as I said my FRONT cam doesn't work on my Iphone 5c.. I had it 2 weeks ago. When I open the photo app its work good for the
    other cam (extern one) but when I wanna take a selfie with the front cam it's like loading and I can't take any picture from the front cam. I'm on an Iphone 5c 8Go on 8.1.2. I was waiting for a bug correction on the new update but it still not working... HELP!
    here the front -->

    Hey there biloute35,
    If you still have not been able to use the front facing camera, I would like to recommend the troubleshooting in the following article:
    Get help with the camera on your iPhone, iPad, or iPod touch
    If you see a closed lens or black screen when you open the Camera app, try these steps:
    Make sure that there’s nothing blocking the camera lens. If you’re using a case, try removing it.
    Force the app to close, then open the Camera app again.
    Restart your device, then open the Camera app again.
    If your device has a front and rear camera, try both cameras by tapping  (camera swap icon). If you see the closed lens or black screen on only one camera, take your device to an Apple Retail Store or Authorized Service Provider for more help.
    Thank you for using Apple Support Communities.
    Take care,
    Sterling

  • HT201471 I have an iPad 3 model A1416 16GB.  It is about 1 1/2 years old. When I opened it today the pad for my password came up and then before I could put in my password the screen went black and now I can not get it to work at all.  What should I do?

    I have an iPad 3 model A1416 16GB.  It is about 1 1/2 years old.  When I opened it today the screen for my password came up and then before I could enter it the screen went blank. I can not get it to do anything now. It had about 24% of charge left. I plugged it into the charger and still nothing. What do I do?  How do I get it to work?

    Try the following:
    1. Reset
    Hold the Sleep and Home button down until you see the Apple logo
    2. Restore:
    http://support.apple.com/kb/HT1414
    3. Recovery:
    http://support.apple.com/kb/HT1808

  • My Itunes account tells me i need to update it to version 10.6.1, but when I click download and the computer (mac 2007) goes to the "checking for softwares" page it doesn't find the update?

    my Itunes account tells me i need to update it to version 10.6.1, but when I click download and the computer (mac 2007) goes to the "checking for softwares" page it doesn't find the update? Help me please, what do I do?

    Try updating to 10.6.3.25.
    A .dmg installer for iTunes version 10.6.3.25 for Mac OS can be found at the following download page on the Apple website:
    iTunes 10.6.3

  • How much to replace the shutter for the Canon 6D?

    I heard some place online said the cost for replace shutter for Canon 5D Mark 2 is about $250, and someone else mentioned to replace the shutter for Canon 6D is about $150.
    Can anyone here tell how much is it cost to replace the shutter for canon 6D from Canon Serivce?
    thanks. 

    As ebiggs has already hinted... it would be extremely surprising if a shutter on a 6D has already failed given the number of shutter activations that these things are rated to take (it would normally take a very active photography many years to wear out a shutter and a casual photographer would be unlikely to ever wear out a shutter.)
    This makes me wonder why you think your shutter has failed.   Perhaps there is a different issue that might be more easily remedied.
    Tim Campbell
    5D II, 5D III, 60Da

  • How do I get the Label for a Front Panel Control to appear in the Block Diagram but not on the Front Panel?

    How do I get the Label for a Front Panel Control to appear in the Block Diagram but not on the Front Panel? On the Front Panel I am making a complex control that consists of a Slider and a Numerical Input box. Both Controls display the same information and either can be used for Input. When one changs, the other is made to display the same value.
     But I only want the Slider to display the Label on the Front Panel, to avoid confusion. On the Block Diagram however, I want both controls to display their Labels so that I know what they are. How do I display the Label for a Control on the Block diagram, but not display its Label on the Front Panel?

    No.  The Label Visible property is separate for the front panel control label and the block diagram terminal label.
    How did you start out with the block diagram's label not being visible?  Whenever I drop a control or indicator, the label is always visible on both the FP and BD by default.  Maybe there is a LabVIEW option that causes new controls/indicators not to have their labels visible by default, but I have yet to find it.  I don't think an item should ever be dropped without the label visible, good LabVIEW coding practice demands that the labels for control terminals on the block diagram be visible so that you know what control or indicator a wire is going to.
    That being said, I have seen a lot of VI's posted where the label for the terminal on the BD is not shown (against good programming practice.)  I've gone to the BD and right clicked to show the label.  Sometimes, the people have an empty label (which will turn off the visibility for both the FP and BD) and I'm forced to add some text of my own into the label so I can figure out what their code is doing.  When I add some text to the label, at that time, I find both the BD and FP labels become visible.
    Are you dealing with controls that have empty labels to start?
    Good programming practices:
    1.  Always have a name for all of your controls, never use and empty label by deleting the text in the label.
    2.  Make the labels unique.  For example, don't have two controls both called Stop.  How do you know quickly know which terminal relates to which control?
    3.  Always show the labels on the block diagram, so you know the function of a control's terminal.  If you want to hide the label on the FP, that's okay.
    4.  If you want a different label to appear on the FP than whatever you actually called the control, then use the caption.  You can hide the label and show the caption.  This is useful if you need to programmatically change what the "label" is on the front panel such if you are making an application that needs to change its user interface such as for a foreign language.

  • HT5361 IN OS 10 where can one find the folder for images that came with email?

    IN OS 10 where can one find the folder for images that came with email?
    I wish to delete the leftover image files to free up drive headroom.

    I checked in this place, no dice!
    Home/Library/Mail Downloads, or
    the system "Downloads" folder

  • My front camera is Not open and the front speaker too

    My front camera is Not open and the front speaker isn't work too

    Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new).  Try each of these in order until the issue is resolved.

  • Why can't I open and retrieve my files from iPhoto and my address book after importing the files from my Power mac G5 to my new Mac Pro? I get a warning that says the new OS on my Pro doesn't open files from a Power Mac. Any idea how I can fix this?

    Why can't I open and retrieve my files from iPhoto and my Address Book after importing the files from my Power Mac G5 to my new Mac Pro? I get a warning that says the new OS on my Pro doesn't open files from a Power Mac. Any idea how I can fix this?

    For your addressbook, export the files to vCard on the PowerMac, then bring them over to your Mac Pro. For your iPhoto, copy the Users -> yourname -> Pictures folder to your Desktop on the Mac Pro, and open iPhoto on the Mac Pro holding the command and option keys.  Select the library file from that Pictures folder and open it.  It should import all the pictures into iPhoto as part of the rebuild process.  Other PowerPC to Intel migration issues are covered here: https://discussions.apple.com/docs/DOC-2295

  • The "general"tab in firefox options doesn't open

    I can't download anymore. Trying to check my settings the "general"tab in firefox options doesn't open. What can I do?
    thanks in advance,
    August

    Hi,
    Please check if the '''Options''' tabs are working in [https://support.mozilla.com/en-US/kb/Safe%20Mode Safe Mode.]
    Useful links:
    [https://support.mozilla.com/en-US/kb/Options%20window All about Tools > Options]
    [http://kb.mozillazine.org/About:config Going beyond Tools > Options - about:config]
    [http://kb.mozillazine.org/About:config_entries about:config Entries]
    [https://support.mozilla.com/en-US/kb/Page%20Info%20window Page Info] Tools (Alt + T) > Page Info, Right-click > View Page Info
    [https://support.mozilla.com/en-US/kb/Keyboard%20shortcuts Keyboard Shortcuts]
    [https://support.mozilla.com/en-US/kb/Viewing%20video%20in%20Firefox%20without%20a%20plugin Viewing Video without Plugins]
    [http://kb.mozillazine.org/Profile_folder_-_Firefox Firefox Profile Folder & Files]
    [https://developer.mozilla.org/en/Command_Line_Options#Browser Firefox Commands]
    [https://support.mozilla.com/en-US/kb/Basic%20Troubleshooting Basic Troubleshooting]
    [https://support.mozilla.com/en-US/kb/common-questions-after-upgrading-firefox-36 After Upgrading]
    [https://support.mozilla.com/en-US/kb/Safe%20Mode Safe Mode]
    [http://kb.mozillazine.org/Problematic_extensions Problematic Extensions]
    [https://support.mozilla.com/en-US/kb/Troubleshooting%20extensions%20and%20themes Troubleshooting Extensions and Themes]
    [https://support.mozilla.com/en-US/kb/Troubleshooting%20plugins Troubleshooting Plugins]
    [http://kb.mozillazine.org/Testing_plugins Testing Plugins]

Maybe you are looking for

  • Mac mini as a voice recorder

    hello planning to buy a mac mini i would like to know if if can be used as a recorder (just connecting a microphone to audio in). does it work ? is there anyone with real experience with it ? thanks in advance and have a nice weekend. Bruno

  • VAT number on PO

    Guys - I have the following error: When i create a PO for one company code in NL for a domestic vendor, the VAT number does not get populated. I have maintained VAT number in vendor master for the vendor and in config for teh company code. Please sug

  • Dynamic Tabs Shell : issue with taskflows using pages

    Hi, We use the Dynamic tabs shell page template in our application. It works fine when used with taskflows with page fragments. However it errors when trying to render a taskflow with pages instead of fragments as: <FormRenderer><encodeAll> Multiple

  • Same problem as all the others - HELP!! Where is my Ipod?

    Like everyone else, Itunes no longer detects my Ipod. I've spent night after night trying everything in the "troubleshoot" list and even met with the "genius" in the apple store.....all to no avail. Basically, iTunes wont recognize by Ipod or crashes

  • Iphoto out of date

    I have iPhoto 09, 8.1.2 and love it but I need to upgrade to use iCloud, but it won't let me. Will I have to purchase iLife '11 to use iCloud then?