The sound on my device isnt working correctly.

When i plug in headphones ( i tried several different sets) it doesnt recognize them and only plays on full volume through the right headphone reguardless of the volume slider and the left one gets no sound. If i do move the volume slider with the headphones in the volume coming through the built in speakers does change.
edit: its an ipod touch 3rd gen

Try the folowing to rule out a software problem
- Reset:
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Restore from backup
- Restore to factory defaults/new iPod
If you still have a problem then you likely have a problem with the headphone jack on the iPod. I would make an appointment at the Genius Bar of an Apple store.

Similar Messages

HT4137 the volume on my iphone isnt working

the volume on my iphone isnt working, how do I fix it?

I had the same problem as well for nearly 3 months.
I had tried bring the Iphone into my phone carrier and they sent me to the AppleStore. When I brought it to them they hooked it up to the diagnostic machine and they told me just to restart the Iphone from the factory settings.
This didn't work either. To complicate things more, other "solutions" seem to only yield temporary success. These temporary solutions included: blowing compressed air into every port, various restart combinations, various factory restore methods.
I had nearly given up until I stumbled upon a support post on Apple's website that finally yielded success.
http://support.apple.com/kb/TS1630
The solution for me is listed as line 7, which reads:
"Check the receiver mesh (which is on the top front of the device, above the display). If it appears blocked, use a clean, small, dry, soft-bristled brush to carefully and gently brush away any debris."
Apparently, this cylinder shaped, mesh area is in some way tied to what triggers the headphones/speaker selection. I am not sure how, but I can say that after gently brushing it out my sounds are working again; specifically my music is now able to play directly off the speakers and my Iphone apps all play their sounds agian.
Hope this helps you as well!

So this morning, the sound on my MacBookPro was working perfectly, but then all of the sudden, the sound didn't work. When i turned the volume up, it showed it turning up, but there was no noise. I also tried plugging in my earphones, and it still didn't

So this morning, the sound on my MacBookPro was working perfectly, but then all of the sudden, the sound didn't work. When i turned the volume up, it showed it turning up, but there was no noise. I also tried plugging in my earphones, and it still didn't work. I don't know what to do!!

Go step by step and test.
1. System Preference > Sound > Output > Internal Speakers
    Highlight Internal Speakers / Headphones
    Make sure that Mute is not enabled.
2.Plug in and remove the headphone.
    If you see red light in the headphone port, plug the headphone
    in and out of the port 5 or 6 times to flip the microswitch inside.
    Sound output may be stuck in the digital mode.
3. Reset PRAM. http://support.apple.com/kb/PH4405
4. Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
5. Applications > Utilities > Audio MIDI Setup
    Audio Devices window
    Side Bar
    Click the Built-in Output.
    Under Mute any of the boxes checked? If so, uncheck it.

Why is the sound on my Envy not working?

Why is the sound on my Envy not working? Checked all volume levels, mute, settings etc.

Hello NellyMac,
You state you are not getting any sound from your laptop, is that correct? I will be happy to help you.
Can you please provide the full make and model of the computer you have, If you are unsure where to locate that information have a look at this link for help if needed.
Please respond back at your earliest convenience.
Thanks
Clicking the White Kudos star on the left is a way to say Thanks!
Clicking the 'Accept as Solution' button is a way to let others know which steps helped solve the problem!

It was found an error in the OPF file: The file is not stored in Cover guide . To ensure the navigation on Kindle devices, you should correct that.

Hi,
I have found errors when uploading the ePub 3 fixed layout classic ebooks on Apple.
It was found an error in the OPF file: The file is not stored in Cover <guide>. To ensure the navigation on Kindle devices, you should correct that.
Please help me?
Thanks,
CK

Thank you but please help me solve this problem.
Kindly look at the below error:
It was found an error in the OPF file: The file is not stored in Cover <guide>. To ensure the navigation on Kindle devices, you should correct that.
Please let me know how it will solve.
Thanks,
CK

I have an Ipod Touch, it appears inactive and says conect to Itunes. When I connect it to the PC, the PC says "USB device not working". How can do to solve this problem.

I have an Ipod Touch, it appears inactive and says "connect to Itunes". When I connect to the PC, the PC says "USB device not working". How could do to solve this problem?

See:
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
or
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP

The sound mute button doesn't work on my HP pavilion dv6

The finger button on the pavilion dv6 doesn't work for the sound mute button. I'm not sure if a setting has been disabled or not. Anyone have any ideas on how to restore it ?

Hi,
Try the following.
Download the IDT Audio installer on the link below and save it to your Downloads folder.
http://ftp.hp.com/pub/softpaq/sp48501-49000/sp48668.exe
When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers. Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
When complete, restart the notebook and let Windows fully load. Open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation. When this has completed, right click the speaker icon in the Taskbar and select Playback Devices. Left click 'Speakers and Headphones' once to highlight it and then click the Set Default button - check if the mute button now functions correctly
Regards,
DP-K.
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

I have had my mac-book pro for almost a year, and have just got OSX Mavericks, and now the sound on my laptop is working in a sporadic way, can I change this at all on system preferences or will I have to get it repaired?

On my mac-book pro the sound isnt working after I have installed OSX Mavericks, should I take it to be repaired, or can I do something on System Preferences?

In addition to checking system preferences/sound/output and selecting built in if that does not work, make sure volume is up and mute not checked.
You can try the following, Take a set of headphones and plug theim in and out several times (there is a micro switch that sometimes gets stuck)
Go to applications>utilities>Audio MIDI set up, see if you can select built in there, make sure volume is uo mute not checked.
Try a NVRAM/PRAM reset:
Power off, power back on holding the following keys OPTION + COMMAND + P + R
Continue to hold these keys till you hear the start chime 2 times, then release,reboot

My trackpad isnt working correctly

When i woke up today my trackpad was just working incorrectly, when i use the left click, it works as it was the ¨enter button ¨ for example in safari when i look for a webpage, for example facebook, when i click the direction bar to start writing, the search starts immediately and i havent even type the webpage yet, other example is here, while im typing this and i make a left click, it takes it as the enter button and this line that indicates where im writing goes down, like this.
im writing, then i use the left click
and now im down.
My trackpad works as the enter button
Can someone tell me what is happening ?
When I restart my laptop the trackpad stills working incorrectly but when i turn it off and then i turn it on it works correctly for a short time and then
starts to work incorrectly again :S
please can someone help me?
Message was edited by: rafasaenz

Try resetting your SMC and pram. Follow the instructions for resetting the SMC for the type of MacBook you have.
MacBook and MacBook Pro
Laptops with a battery you can remove
Shut down the computer.
Disconnect the MagSafe power adapter from the computer, if it's connected.
Remove the battery.
Press and hold the power button for 5 seconds.
Release the power button.
Reconnect the battery and MagSafe power adapter.
Press the power button to turn on the computer.
Newer Mac portables
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
Resetting NVRAM / PRAM
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

Device not work correctly

sometime USB port not work correctly, the device only flashes once and then off, the process of "system" increases the CPU to 100%. then I reboot and it works back

What do you mean "the measurement failed"
Can you please provide more details. Like an error code.

No sound and audio device not working properly, T61 vista

I unistalled the audio device SoundMax integrated HD audio because I had problems getting the mic of my new webcam (Logitech pro 9000) to work. But after reinstalling the SoundMax audio driver the audio device is no longer working.
Installing the SoundMax driver doesn't report any problems and the device manger also says that the SoundMax integrated digital hd audio device is working properly. But the speaker icon on the taskbar is crossed out. When hovering the mouse over the speaker icon it says Volume: 0 SoundMax integrated digital hd audio. When opening the Volume Mixer it says "No audio decivice is installed"...
I've completly removed all drivers and reinstalling several times but I cannot get it to work so I really need some help now.
All software + drivers regarging the webcam has been completly removed.
System data:
T61, Vista business
Audio chip seems to be a Analog Devices 1984
SoundMax driver version 6.10.1.5510 (latest available from lenovo)

Really silly bug, but there are times with the T series laptops, specifically the T61s that seem to not project the sound through the speakers and the way to fix it is to just keep hitting the silver volume buttons up by your power button on the actual laptop. This may or may not work for you, but I literally just got done with this on a T61 running a fresh installation of XP. The buttons on the lenovo itself control the direct signal input and do a very poor job with integrating with Windows Vista and XP.
Let me know if that works for you.

I can't get the sound on the games to work on my ipad 2?~the sound on everything else is working

My ipad is working fine except the sounds won't play when playing games!

I am talking about the Ver 3 download link that came with the purchase email.
That link is no longer available. Use "Migration Assistant" to copy your Applications from your old mac to the new Mac, then immediately run software update. Aperture Version 3.2 will not run on your new mac with Mavericks, you will have to Upgrade to version 3.4.5 at least - you can download this update from the Support page: Aperture 3.4.5
Then launch Aperture and enter your registration key and try now too update from version 3.4.5 to 3.5 from the AppStore. The AppStore will change your Aperture registration to an AppStore version, so you will able to reinstall by downloading from the AppSTore in future.
If you want transfer only Aperture and no other applications, do it manually: You will have to copy not only the application but folders from the libraries as well:
/Applications/Aperture.app
/Library/Application Support/Aperture/
~/Library/Application Support/Aperture/
Leonie

How can I get the sounds , like clicking,etc to work on iPad 2 with IOS 5. In the settings all sounds are on and the volume is high but I don't get a sound.

After downloading IOS 5, I no longer get the sounds on my IPAD 2 to work. They are on in settings and the volume is at maximum, but the sounds such as keyboard click, email sent etc, donor work.
Any suggestions.
Regards

Have you got notifications muted ? Only notifications (including games) get muted, so the iPod and Videos apps, and headphones, still get sound.
Depending on what you've got Settings > General > Use Side Switch To set to (mute or rotation lock), then you can mute notifications by the switch on the right hand side of the iPad, or via the taskbar : double-click the home button; slide from the left; and it's the icon far left; press home again to exit the taskbar. The function that isn't on the side switch is set via the taskbar instead : http://support.apple.com/kb/HT4085

Please help the sounds on my games wont work

The sounds on the ipod on my ipad work but the sounds for all of my other apps are not working please help

OK......double click your home button and swipe the lowest row of apps you've recently used will come up. With you finger, swipe that row to the right and you'll likely see an icon on the far left that is a mute icon. Touch it and your sounds should come back.
Don't be scared. There is something simple and we're going to find it.

The calendar sync is recently not working correctly, not display "All events" but it only displays the last six months for my individual entries. My repeating entires do go back further, though. How do I fix?

I have an iPad 5.1.1. The calendar sync has started to not work correctly. I have it checked "All events," but it only displays the last two months for my individual entries. My repeating entires do go back further, though. How do I fix?

HI Jason269. Thanks for your reply, however I wrote that I already have "All events" checked. If All Events is checked and it doesn't diaplay all events, how do I fix? It seems this is a common issue, as I have read many others on here state the same problem.
I believe my problem occurred when I synced my iMac calendar to my iPad calendar using yahoo. Yesterday, I unsynced them on my iMac controls. When I checked my iPad calendar, all of my old entries reappeared - but only for five seconds and disappeared again. So, the data is saved and still there but cannot be displayed, even when I have All events checked. In fact, it only shows my individual entries for the last two months, but does show all my recurring entries. If I switched to last six months, I will see everything for the last six months. If I switch back to all events, it is only for the last two months.
As I mentioned, others on here have expressed exactly the same issue, including the two month example and having used yahoo.
For legal purposes, I need to be able to use the information from my indidual calendar entries in an upcoming court case. So I really need to fix this ASAP!

The sound on my device isnt working correctly.

Similar Messages

Maybe you are looking for