The sound won't work

Every time I try to make the sound work it just shows me this crossed out speaker with one of those do not enter looking signs below it please help!

Hopefully one of these steps should solve the problem.
1. System Preference > Sound > Output > Internal Speakers
    Make sure Mute is not enabled.
2. Remove the headphone.
    If you see red light in the headphone port, plug the headphone
    in and out of the port 5 or 6 times to flip the microswitch inside.
    Sound output may be stuck in the digital mode.
3. Reset PRAM.  http://support.apple.com/kb/PH4405
4. Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
5. Applications > Utilities > Audio MIDI Setup
    Audio Devices window
    Side Bar
    Click the Built-in Output.
    Under Mute any of the boxes checked? If so uncheck it.
Best.

Similar Messages

  • I accidentally left my phone unprotected during the rain. My phone got wet and when I got home the sound won't work and the next day it doesn't let me charge anymore. HELP!

    I went out to join the amazing race challenge in my work. When we were almost to the end, the weather changed and it started raining. I put my phone my my backpack and got wet along with my other stuff. By the time I got home, there's no more sound and it keeps showing "SLIDE TO TURN OFF". Then the next day, I can't charge anymore.

    You might consider a case like Otterbox or something similar for active events in outdoor use. They not only give good protection against drops but also protect from water. It's not meant to swim with take underwater pictures but really good for rain splatter or the situation you were in. Good luck.

  • TS3518 When using a projector the sound won't work with the picture.  I get one or the other. What can I do to get both?

    How can I get airplay to show picture and have sound using a VGA to hdmi adapter with Apple TV.  It won't play my video apps with sound? I get a choice of sound or video but not both?

    vga don't carry any sort of audio

  • HT2494 the sound won't work on my Macbook pro  the headphone port actually has a red light coming from it

    Can not get sound on my Computer.  The headphone port actually has a red light coming from it.  Help

    Insert a headphone jack and remove it and see if the light goes out. The red light indicates the switch didn't switch from head phone to your Mac's speakers. Some folks have actually used a match stick to undo the switch.

  • My sound won't work, how do i fix it if I've already tried the audio MIDI setup?

    So i plugged in a stereo system and when i unplugged it the sound won't work anymore unless it's plugged in? How do i fix it?

    Check  this document.
    Error "Licensing has stopped working" | Mac OS
    Try each step.
    When you get to the license recovery kit, type sudo, leave a space and drag LicenseRecover.py into
    the Terminal screen, then hit Enter. It should look like this:
    Enter your password, but remember the cursor will not move. Just hit enter and let the script run.

  • My macbook's sound won't work - no output devices found in settings?

    I've been having a lot of issues with my Macbook.  It has a 2.4 GHz Intel Core 2 Duo processor and is running on version 10.6.8 Mac OS X.  It asks for certification whenever surfing the web or loading websites, and always redirects to a different page.  Now, the sound won't work at all - regardless of mute on/ off or sound turning up and down. I went to settings to check out the problem, and there is no output or input device listed or found on that page.  I have no idea what's going on, and now, even though it's plugged in it won't charge.

    First thing I would try for your sound output issue would be to reset the parameter RAM.
    Best of luck.

  • TS3274 Sound won't work for games

    THe sound won't work for games unless I plug In headphones. The setting shows like the sound is on.

    If you lose sounds for keyboard clicks, games or other apps, email notifications and other notifications, system sounds may have been muted.
    System sounds can be muted and controlled two different ways. The screen lock rotation can be controlled in the same manner as well.
    Settings>General>Use Side Switch to: Mute System sounds. If this option is selected, the switch on the side of the iPad above the volume rocker will mute system sounds.
    If you choose Lock Screen Rotation, then the switch locks the screen. If the screen is locked, you will see a lock icon in the upper right corner next to the battery indicator gauge.
    If you have the side switch set to lock screen rotation then the system sound control is in the task bar. Double tap the home button and in the task bar at the bottom, swipe all the way to the right. The speaker icon is all the way to the left. Tap on it and system sounds will return.
    If you have the side switch set to mute system sounds, then the screen lock rotation can be accessed via the task bar in the same manner as described above.
    This support article from Apple explains how the side switch works.
    http://support.apple.com/kb/HT4085

  • Please help. My sound won't work.

    I've had this iPod for awhile and sometimes when I try to listen to music, the sound won't work. I've tried turning my iPod on and off, but this doesn't work. I know my sound is all the way up. It usually works just fine with headphones but not without them. I turned my iPod off and on and it plate music for the first few seconds and stopped after that. It feels a little hot when I listen to music but I turned it off too keep it cool. And when I turned it back on and played music I noticed it getting a little hot when it stopped. Is it overheating? What do I do?

    It worked right after I pushed power and home button. But the sound is gone again. When I open music there is no slider for volume. The mute switch is not on, so I'm not sure what is wrong. Would u have anymore suggestions.
    Thank you

  • My macbook pro is freezing/sound won't work

    A few days ago my Macbook pro started freezing up and requiring a forced power off each time. Sometimes the screen would go completely white, other times the cursor would still move but the display was broken and unable to be clicked. It happens at random intervals, sometimes without me even running any programs it will freeze up and go to a blank screen. A lot of times it takes a few consecutive tries to actually restart it in the first place.
    Anyway, I contacted Apple Support Chat and the employee helped me to Repair the Disk Permissions which provided a temporary fix. After it kept acting up later, I followed her instructions to do both a PRAM reset and SMC reset. However, after performing both of those today now my screen has gone dark blue a few times and also the sound won't work with or without headphones.
    Could someone please help me?

    A few days ago my Macbook pro started freezing up and requiring a forced power off each time. Sometimes the screen would go completely white, other times the cursor would still move but the display was broken and unable to be clicked. It happens at random intervals, sometimes without me even running any programs it will freeze up and go to a blank screen. A lot of times it takes a few consecutive tries to actually restart it in the first place.
    Anyway, I contacted Apple Support Chat and the employee helped me to Repair the Disk Permissions which provided a temporary fix. After it kept acting up later, I followed her instructions to do both a PRAM reset and SMC reset. However, after performing both of those today now my screen has gone dark blue a few times and also the sound won't work with or without headphones.
    Could someone please help me?

  • My sound won't work on my ipod 5. I plugged the speakers in and it works fine.  When the headphones aren't plugged in and I turn the volume up it says that they are plugged in.  Please help !

    my sound won't work on my ipod 5. I plugged the speakers in and it works fine.  When the headphones aren't plugged in and I turn the volume up it says that they are plugged in.  Please help !

    - Try cleaning out/blowing out the headphone jack. Try inserting/removing the plug a dozen times or so. (this was already sugested) There is a little switch in the headphone jack that disconnects the speaker when the headphone jack is inserted.
    Try the following to rule out a software problem
    - Check also Settings > General > Accessibility > Hearing. Make sure that the sound balance is not set all the way to "R".
    - Reset the iPod. Nothing will be lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup
    - Restore to factory settings/new iPod.
    - Make an appointment at the Genius Bar of an Apple store. Seems you have a bad headphone jack.
    Apple Retail Store - Genius Bar
    If not under warranty Apple will exchange your iPod for a refurbished one for this price. They do not fix yours.
    Apple - iPod Repair price                  
    A third-party place like the following will replace the jack for less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
    Replace the jack yourself
    iPod Touch Repair – iFixit

  • My iPad2 side switch is acting up, it will only allow me to have either sound or rotate. If I unmute the rotate won't work, if I mute the rotate works. How can I get the iPad to unmute and rotate? I have restored, downloaded updates and rebooted.

    My iPad2 side switch is acting up, it will only allow me to have either sound or rotate. If I unmute the rotate won't work, if I mute the rotate works. How can I get the iPad to unmute and rotate? I have restored, downloaded updates and rebooted.

    You should be able to control the function that the side switch isn't controlling via the left-hand end of the taskbar : http://support.apple.com/kb/HT4085 - is the icon that appears there (notification mute or rotation lock) indicating that that function is 'off' ?

  • My sound won't work on my ipad even though the sound is up and the button on the side is on volume? Any ideas ipad 2

    My sound won't work on my ipad even though the sound is up and the button at the side is on volume? Any ideas. For ipad 2

    They will replace it with a refurb of like kind if the problem is deemed to be hardware related and not caused by misue. They will probably try restoring the device and troubleshoot it on their own before they replace it for you .... And I'm talking about an Apple Store here.
    You should probably try this next.
    You can try resetting all settings. Settings>General>Reset>Reset All Settings. You will have to enter all of your device settings again.... All of the settings in the settings app will have to be re-entered.

  • My Mac's sound won't work-the buttons do though

    When I play videos(i haven't checked youtube yet) my sound was out if i paused the video and restarted. Now my sound won't work at all or even for my Facebook games. I had this problem before with just youtube and i was able to fix that, but now i can't fix this. Help?

    Hey saxon198
    If it is just the one user account, then the next step would be to migrate the data that you have to a new user. The best method is to copy your Home Folder to an external hard drive. The next step after that is complete is to delete the user that is causing the issue. Then all you have to do is to copy your data back over. Just copy the contents of the documents folder into the new documents folder instead of replacing it. Now things that probably will not make the move unless you have iCloud or another syncing service is Contacts, Calendars and Notes. You can export those if needed. If it seems confusing or to daunting, then the next step would be to contact Apple Support for further help. I have provided a link to do so with multiple different options for you.
    Isolating an issue by using another user account
    http://support.apple.com/kb/TS4053
    OS X: Manually migrating data from another Mac
    http://support.apple.com/kb/HT6101
    Contact Apple Support
    https://www.apple.com/support/contact/
    Regards,
    -Norm G.

  • The turn-on sound won't Work, the computer opens ok silently??

    The turn-on sound won't Work, the computer opens ok, but silently??

    Restart in Safe Mode, it's possible a cache may have become corrupt.

  • I just got an iphone 4 yesterday. I got everything all set up and working great. When I woke up last this morning, my ipod has no sound and the albums covers are all mixed up. I've checked all my settings and volume control. My text sound won't work eithe

    I just got an iphone 4 yesterday. I got everything all set up and working great. When I woke up last this morning, my ipod has no sound and the albums covers are all mixed up. I've checked all my settings and volume control. My text sound won't work either. However, my ringtone works just fine.

    Have you taken the steps recommended in the User Guide:  restart, reset, restore?

Maybe you are looking for

  • SDK 2007 on SAP B1 2005 Company Database

    Hi Guys, Does anybody know how or could we use the library of SDK 2007 (SAPbobsCOM2007.dll) on company that still running SAP B1 2005 SP1 ?? Currently in my system has installed : 1. SAP B1 Server 2005 2. SAP B1 Client 2005 3. SAP B1 SDK 2005 4. SAP

  • SRW.SET_HYPERLINK - Handle SPACE in filename AND open in NEW WINDOW

    Report 10g (10.1.2.3.0 - 32bit on Windows 7 64bit) Issue #1: using srw.set_hyperlink to get a handle on *.pdf file on remote server. Report is launched as PDF. PDF that is opened via the URL launches in same window as report. I need run report as PDF

  • Delayed image loading

    hi there I'm working on a project including a GUI with images. I'm loading image-files using Toolkit.getDefaultToolkit().getImage() and I display them with the drawImage()-method from the Graphics class. The problem is the following: The loading of I

  • Load Balancing Two Servers

    i have two Solaris servers running 9iAS R2 OC4j. current patch level is 9.0.2.3 i'm trying to load balance the instances according to the instructions in this document: Oracle9i Application Server: mod_oc4j Technical Overview all i should need to do

  • Backend Operation for OK button of Data Set tab of Data Definition

    Hello everyone, Please let me know what happens at backend when we click on OK button Data Set tab of Data Definition in Unifier ! Cheers, Gagan