The Tale of the Beeping Macbook - AKA- My Macbook Pro keeps beeping when trying to boot into Snow Leopard Disc's disk utility

Quick back story: about a month ago my macbook was falling and I caught it quickly, I had a game controller in my hand and it lightly hit it whilst I was catching it; the laptop made no contact with the floor, couch etc. Upon reveling in my epic matrix esque catch I noticed it was beeping and the screen was completely black - Horrified I held down the power button for a forced power down and then turned it back on to see that it was fine, along with no visible scars, dents etc to the chassis. Now flash forward to present day, and the macbook pro is only two months old (bought may 4th 2011) and I notice it's got some slightly irregular slow loading points when loading a browser, photoshop, etc. I do the standard disk utility to verify the disc and it says
"Checking volume bitmap.
Checking volume information.
Invalid volume file count
(It should be 537095 instead of 537096)
Invalid volume directory count
(It should be 161641 instead of 161640)
The volume Macintosh HD was found corrupt and needs to be repaired.
Error: This disk needs to be repaired. Start up your computer with another disk (such as your Mac OS X installation disc), and then use Disk Utility to repair this disk."
So I put in the snow leopard disc to go to the disk utility within, reboot the laptop, and it goes to the gray boot screen with the dark gray apple logo and stays there whilst doing the aforementioned beep from my spider-sense catch. Does anyone happen to know what is wrong? Would that tiny tap from my controller when catching it have caused this problem I have now? Is there anything I can do at home to fix this since I can't get to the disk utility on the snow leopard disk? Will Batman ever get out of the Joker's trap? Or am I better off just making a genius bar appointment? Thanks in advance.
-ZRS

Are you using the Snow Leopard disc that came with that Mac? A gray disc that came with a different Mac won't boot yours, and a Retail (white) disc with a version of OSX earlier than the one your Mac came with won't boot it, either.
If you don't have the right disc, do you have an external HD, or can you borrow one?
(By the way, your post shows you're running Tiger; you might want to update that.)

Similar Messages

I have a MacBook Pro 15" and my warranty just ran out! I partitioned my harddrive into two partitions, one with Snow Leopard and the other with microsoft.This morning I turned on my Macbook Pro and it will not boot into Snow Leopard.

Good Morning,
I have a MacBook Pro 15" and my warranty just ran out! I partitioned my harddrive into two partitions, one with Snow Leopard and the other with microsoft.This morning I turned on my Macbook Pro and it will not boot into Snow Leopard. I shut it off took out the battery, reinstalled the battery. Then I put in the Snow Leopard CD and booted up to disk utility and The Snow Leopard partion would not show up?? I do see the microsoft partion.
I also rebooted holding down the shift key and still no Snow Leopard
Could you please tell me what I can do, what keys do I press on restart any advice to get Snow leopard back.
thank you.

Have you restarted holding down the Opt key? That procedure should give you a gray screen with all of the partitions that exist. Then select the SL partition for boot. Also go to System Preferences and Startup Disk, unlock the lock and select the SL partition as the default boot partition, then relock.

When i try to install snow leopard with install disk, it has me restart the computer instead of installing. can anyone help me figure out how to get the disk to actually install?

when i try to install snow leopard with install disk, it has me restart the computer instead of installing. can anyone help me figure out how to get the disk to actually install?

Ok, it's just a glitch that it's not auto-rebooting from the disk.
Please backup your personal files off the machine to a regualr external drive and disconnect all drives before doing anything
Take the 10.6 disk out and clean and polish the bottom with a very soft clean cloth and a tiny bit of rubbing alcohol to cut the oils.
Stick the disk in and reboot holding c key down, this will make it boot from the disk and you can install Snow Leopard that way.

After installing it, my macbook would not restart. All i would see is the Apple and the twirling circle. To get back to be able to use internet i had to put Snow Leopard disc holding "C" key.

I did a software update check. It showed to update to 10.6.8v1.1. After installing it, my MacBook would not restart.
I have tried this more than once. After the install all that happens is i get the Apple emblem and the twirling circle. I have let that go for literaly a couple hours with no results.
To get to be able to use my Macbook i have had to install Snow Leopard by holding the C" key and re-installing Snow Leopard.
Any help would be appreciated. i Have purchased "Lion" and cant access App Store to install until this update is done.
Very frustrating.
thanks in advance.

That's why you can't access the App Store. Minimum requirement is v10.6.6
Install this combo update > Mac OS X 10.6.8 Update Combo
Then restart your Mac, open the App Store.
You can download Lion by clicking Redeem under Quick Links right side of the App Store window then entering the redemption code.
You have checked to make sure your Mac can run v10.7 Lion? >>>> OS X Lion - Technical Specifications

My 2008 iMac will get to the white boot up screen and has the loading circle and then it will freeze. And will freeze when attempting to boot recovery or bootable disc of Mavericks

Hi there, I have a 2008 iMac 24' 3.06 Intel Duo with 4gb ram. And yesterday it was working totally fine and jolly with no issues. Then I noticed there was an OS X update for Mavericks, so I finally decided to do it, and once it was rebooted it went to like the grey screen and I could move my mouse, just nothing else was there. So I tried to restart it, and then it booted up, but was really laggy, and so I decided to restart it and try again, this time the iMac froze at the login. So I decided to take it apart, pull the 500gb hard drive, connect it to my MacBook Pro, and then formatted it in Disc Utility. From there, I opened the Mavericks installer on my MacBook and then installed it to the iMac's hard drive via usb hard drive enclosement. And once the install of Mavericks was completed, I put the hard drive back into the iMac and tried to boot it. It now boots up to the white screen with the Apple and the loading circle underneath the Apple and then it freezes and doesn't go any further. So then once that happened, I turned it off and tried to boot it into recovery mode. Then it freezes on the screen with the Apple and loading circle below it. Then out of desperation, tried to use a bootable disc of Mavericks to see if i can at least get the iMac to boot up again, with no success. It froze at the same point again. So now I reach out to the Apple Community to see if anyone else has an idea on what I can do or if anyone had this issue and what they did to resolve it. Any help would be great. Thanks.

mddcfilms and Pat75, I'm having precisely this same issue -- no booting but spinning and freezing gear under the Apple logo. Have either of you come to a resolution? Here are my details:
iMac, Early 2008, 24”, 3.06 GHz, 4GB
September 2013: Nvidia GeForce 8800 GS GPU repaired, HDD replaced with Western Digital 2TB
21 April 2014: Erased HDD with Disk Utility on Mavericks USB; clean installation of Mavericks from the USB. Process completed without issue, including registration process. After a minute or two of poking around, machine shut down immediately (not through the shut-down process).
Since then it will not boot up. Grey screen and Apple logo appear, with gear spinning; the gear freezes, then the machine tries to boot up again. Occasionally I’ll hear “To use English for the main language, press the return key.”
I’ve tried booting into Safe Mode; same gear freeze and restart.
I’ve tried booting to the 10.9 Recovery disk; same gear freeze and restart.
Tried booting from Mavericks USB; same freeze and restart.
Tried booting from 10.6.3 DVD; same freeze and restart.
Ran Apple Service Toolkit (at Stormfront in the UK), which turned up nothing in error.
Started in single-user mode to test HDD and RAM, which are fine.
Started in verbose mode to check logs; some error messages but nothing seems crucial. After the log screen, the grey screen and Apple logo appear, gear spins, and then freeze.
Cannot get to Apple Hardware Test (vintage machine too old?)
Cannot get to Target Disk Mode with my MacBook Pro
Ideas: Potential booting flaw in Mavericks installation. Firmware incompatibility with Mavericks. Hardware issue in Nvidia GPU (known for problems). At the moment I'm hoping that it's a Mavericks installation or firmware issue, though I suspect the Nvidia GPU has blown up on me. These graphics cards are known for being pieces of junk, so I may try installing the lower spec ATI Radeon 2600 GPU if I can find one at a reasonable price.
Anybody else have precisely these problems or have any advice?

Is it possible to bypass the number of partitions limitation (no more than 2) when trying to boot into windows by not using boot camp assistant, and instead just partitioning the drive manually?

I can't find a specific answer to this question.
I did have a functioning Windows 8 installation on my MacBook Pro previously. I tried to make a third exFAT partition so as to have a drive mutually readable/writable to both operating systems. This made it so I could no longer boot into my Windows installation.
I know I'll need the boot camp drivers installed on the Windows installation after the fact, but would manually creating a partition and installing the OS without Boot Camp Assistant work? And would I be able to boot from it while having a total of 3 partitions?

That's the spirit!
Just be sure to have your OS X junk safe in a tested backup, in case the whole thing craps out and you end up having to do a low-level partition and erase of the entire drive.
And like I said, the problem is not OS X. I've set up mine at least once with 4 partitions holding as many flavors of OS X as can run on the hardware, all perfectly bootable on demand.

"The requested operation requires elevation" is an error message I keep getting when trying to open attachments or documents. How do I get rid of this?

I keep getting the error message "The requested operation requires elevation" when I try to open attachments or documents. How do I get rid of this?

This is the entire message. I have gotten this message many, many times and it's always the same.
I'm trying to open text attachments to Thunderbird with Open Office.

IMac won't boot unless snow leopard disc is in the drive

I am running 10.6.4 and have a boot camp partition running windows 7. The windows side is working fine, however snow leopard will not boot unless I put the disc in the drive. I don't need to do anything else at all, just put the disc in. If I do not put the disc in, I get the apple logo appear, a time bar appears at the bottom of the screen which fills up a small amount and then disappears and then I get the grey spinning circle and the apple logo for ever more!
Can anyone please offer me some advice?

Something you could try would be booting to the Snow Leopard install disk. Once at the welcome screen, choose your language and click next. At the top of the screen you will notice the menu bar appear, choose Utilities > Disk Utility. In Disk Utility choose your Mac partition, from there go to the First Aid tab and Verify the Disk and also your Disk Permissions. If any errors show up click Repair on the respective option. After that try booting to OS X again, without the Snow Leopard disk inserted.

Unable to upgrade my 3 year-old MacBook Pro (w/ Intel chip) 10.5.8 to Snow Leopard using installation disk. Why is this so difficult?

I have a macbook pro OSX 10.5.8 and cannot seem to upgrade to Snow Leopard using my Snow Leopard disk. My MacBook Pro has an Intel chip. Why is this so complicated and how am I supposed to install Snow Leopard if I can't do it via disk??

It may interest you to know that if you want to upgrade to Lion, the only additional cost will be $29 - one price for all the computers using your Apple ID. You must upgrade to Snow Leopard first.
Something else to keep in mind - your MacBook Pros may also meet Mountain Lions's requirements:
Macs that will support OS X 10.8 Mountain Lion
As usual, the newer the Mac the better:
MacBook Pro – 13″ from mid 2009 or later, 15″ from late 2007 and newer, 17″ from late 2007 and newer
from http://osxdaily.com/2012/02/16/os-x-10-8-mountain-lion-system-requirements/

MacBook Pro won't boot into Snow Leopard

Hello all,
I've been running Snow Leopard for a few weeks now with no problem, but today my laptop refuses to boot into the Snow Lepoard partition, it is stuck on a grey screen with the logo and a spinning wheel.
I have tried booting into safe mode with no luck. Also I have a Windows boot camp partition which I can boot to and work properly, and finally I have booted from the Snow Leopard disk and run disk utility, the HDD can be verified and the only warnings I get when repairing permissions are about SUID files being modified and will not be repaired. I don't know if that s the root of my problems, any advise will be greatly appreachiated (sp?).
Thanks

Thanks for the help, but I would like to know what went wrong and how to avoid this in the future.
I've usually found that such problems are accompanied by hard drive damage, but you say it's testing fine, so that's obviously not it. But sometimes vital files get corrupted somehow and you never know why, unfortunately. It could have its roots in some application crashing a year ago.

I get "The requested URL /mc/welcome was not found on this server." when trying to log into Yahoo email

I can log into my Yahoo accounts with IE. I've tried disabling my plug-ins and extensions and logging in under safe mode. It's also not a version issue. I've been using 3.6.13 for a while and the problem first arose about 3 days ago. Upgrading to version 4 doesn't help either.

I had the exact same problem and I found it to be in the Panda Cloud anti-virus software. Panda Cloud added on a "URL SECURITY" feature and this started the problem. I uninstalled this "feature" and problem solved.

IMac fell on the floor - Windows 7 boots up, Snow Leopard does not

Hello everyone
My first generation aluminium-intel-mac fell off a small stool I carelessly placed it on. Interestingly, pressing the option-key and booting up windows after turning on the power works just fine. Trying to boot up Snow Leopard however won't get me past the loading screen. Also, there's this odd clicking noise every few seconds.
I've tried the following:
Starting up in safe mode -> loading screen
Resetting NVRAM -> loading screen
Booting from the Snow Leopard Install disk -> loading screen
Help!

That odd clicking sound tells me you damaged your Hard Drive when you dropped it. Take it to an Authorized Apple Service Provider.

Why does my MacBook pro keep beeping 3 times. The screen is frozen.

Like my MacBook Pro keeps beeping 3 times and pausing for 2 seconds. The screen is frozen. How do I fix this and what is going on?

That is a RAM issue, do you have any spare ram you can swap to confirm? Possible causes:
a ram module going bad
installation of incompatible ram
your ram may have become dislodged
I would suggest:
- removing all ram from your MBP, and reinstall it to see if that helps.
- if you recently installed new ram, remove it, then restart the computer with the old ram to see if this helps.

!!!HI, SO I BOUGHT MOUNTAIN LION ON MY MACBOOK PRO TRYING TO UPGRADE FROM SNOW LEOPARD, AND WHILE TRYING TO REINSTALL THE OS SETUP AS IT SHOWED IT COULDNT BE VERIFIED, I CROSSED OUT MOUNTAIN LION FROM MY PURCHASES, ITS NOW GONE, DO I HAVE TO BUY IT AGAIN?

HI, SO I BOUGHT MOUNTAIN LION ON MY MACBOOK PRO TRYING TO UPGRADE FROM SNOW LEOPARD, AND WHILE TRYING TO REINSTALL THE OS SETUP AS IT SHOWED IT COULDNT BE VERIFIED, I CROSSED OUT MOUNTAIN LION FROM MY PURCHASES, ITS NOW GONE, DO I HAVE TO BUY IT AGAIN?

Please google search for "Mountain Lion disk crash" before upgrading you mac pro. You might need to replace you Mac hard drive after the upgrade.So many people had the same problems including me.
Be aware of the Mountain Lion upgrade problem.

I did a factory reset on my late 2008 MacBook from a Snow Leopard disc. It installed fine, but as soon as I began to use the computer (safari) it froze. Couldn't even force quit. So I held down the power button to turn it off, and now it won't start up.

I did a factory reset on my late 2008 MacBook from a Snow Leopard disc. It installed fine, but as soon as I began to use the computer (safari) it froze. Couldn't even force quit. So I held down the power button to turn it off, and now it won't start up. It goes to the grey Apple screen and just sits there loud as can be. Help! Please keep in mind I've not done anything like this before and am going to need a little hand-holding. Thanks in advance.

Hi. Don't worry it's nothing serious. Insert the Instal Disc (Snow Leopard) and press the C button while turning on the computer. Once you see the desktop, go to Utility and choose Disk Utility. Select the Macintosh Partition on the left window pane and then click on Repair Disk and Repair Disk Permissions on the bottom right corner. Wait for both processes to finish. Click on the Apple icon (top left corner) and choose quit. Your computer should restart. See if it reboots normally. If not you can always reinstall the OS following the same steps. Good luck!

The Tale of the Beeping Macbook - AKA- My Macbook Pro keeps beeping when trying to boot into Snow Leopard Disc's disk utility

Similar Messages

Maybe you are looking for