The wireless connection keeps going away and I need to power off and on the time capsule to get the wifi network up

Time Capsule wifi access very poor. it keeps disconnecting and i need to power on and off thr router to get the wifi connection back again. When it works its so slow, it works only in the roms nearby and not even upstairs in my home!

I cannot work from the serial number.. I need the model number. A1xxx in the rubber .. in the rubber.. for Gen1-3.. 2010 is probably Gen3 but can be early Gen4.
Follow up questions:
How do i take the firmware back to 7.6.1 or 7.5.2
wireless names are Room of requirement and Leaky Cauldron - Is that too long a name?
How do I set fixed wireless channels?
Can relocate. Its in the main level of the house to give me access upstairs in the bedrooms and down in the basement,
Change firmware.. hold down option whilst clicking version.
Wireless names.. short, no spaces and pure alphanumeric.. yes.. your names are wrong.. from my point of view.. more they do not obey the rules.. no spaces.
Check C9 here why this is important.
http://pondini.org/TM/Troubleshooting.html
Fix wireless channels.. option page in wireless are of utility.. you need to spend more time in the utility so you know what is there.
Location is everything.. sometimes you simply need more than one device.. wireless has limited range. Use ethernet or EOP - homeplug adapters to place another AP in area closer to your position.

Similar Messages

Want stream Netflix to blueray via Airport Express wifi. The blueray finds my wifi but the wireless connection failed - said, Ensure DHCP server is enabled on router and restart router. Don't think I have DHCP server. Suggestions anyone?

Want to stream Netflix to blueray player via my existing Airport Express wifi. The player finds my wifi but the wireless connection fails - says, " Ensure DHCP server is enabled on router and restart router." I don't think I have a DHCP server. Suggestions anyone?

I can't speak specifically regarding LG, but the Whole Home feature on Direct TV (record a movie on one DVR and watch it on another TV in another location) just won't work with wireless, and I have a strong fast connection at 300 Mbps. Ethernet works perfectly.
Few audio/video products will accept "n" wireless at 5 GHz. I suspect that your LG accepts a 2.4 GHz signal, which would top out at 130 Mpbs.
If you are trying to stream High Definition video, especially at 1080P, my opinion would be that it is unlikely that you will be able to do so reliably using wireless.
Perhaps another user who has figured out how to do this will post with some input.

Every time I try to connect to my 2TB Airport Time Capsule I get the following msg - "The server may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and

Every time I try to connect to my 2TB Airport Time Capsule I get the following message "The server may not exist or is unavailable at this time. Check the server name or IP address, check your network connection, and then try again." However, if I unplug it and then plug it in again, I can connect to it. How can this be corrected without having to unplug it all the time?

Are you using Yosemite??
This is stock standard yosemite bug and we have no simple fix for you..
You can fix it at its source..
Hack in DNS from Mavericks.. so Yosemite can be raised to a level of reliability above GHASTLY.. !!
http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/
Apple still have not fixed it.. and users are now sick and tired of the problem.. so have resorted to what can only be described as extreme measures.. in fact I wonder why people don't just revert to Mavericks.. or earlier.. whatever OS was reliable.. instead of seeing the latest greatest update as necessity.

When back up to time capsule I get the message no access to backupcopyfiledisc/Volume/data/imac.sparsebundle ( error - 1 )

When back up to time capsule I get the message no access to backupcopyfiledisc/Volume/Data/Terjesumac.sparsebundle ( error-1)

Try #C17 in Time Machine - Troubleshooting for known fixes. Works for me as well.
http://pondini.org/TM/Troubleshooting.html

After trying to restore from time capsule, I get the following message when I try to access the folder "data." The folder "Data" can't be opened because you don't have permission to see its contents. Any ideas?

after trying to restore from time capsule, I get the following message when I try to access the folder "data": "The folder “Data” can’t be opened because you don’t have permission to see its contents." Any ideas?

Are you restoring from a TM backup??
Check the methods Pondini outlines to do restore.
Q14-17
http://pondini.org/TM/FAQ.html

When my time machine tries to backup to my time capsule I get the following message"The backup disk image "/Volumes/Data/Kent's MacBook Pro.sparsebundle" is already in use. " What do I need to do to fix this?

When my time machine tries to backup to my time capsule I get the following message"The backup disk image “/Volumes/Data/Kent’s MacBook Pro.sparsebundle” is already in use. " What do I need to do to fix this?

Restart the Time Capsule.

I have: iMac 3.06GHz Intel Core i3, 4GB RAM, OS 10.7.5. It seems that a few times a day, the internet turns off and I need to turn OFF and then ON. There has also been about 3x in a week where everything freezes and I have to power down. What can I do?

What can I do to find out what's wrong with my iMac?
Internet keeps shutting down. I have to turn OFF and then ON. Sometimes, I'm just browsing the web, sometimes on Facebook and lately it happens when I'm on Dropbox uploading.
A few times while editing photos on Lightroom or Photoshop the computer will freeze and I can't do anything but power off ..
What can I do to see what's wrong with my iMac?
Thanks so much!
T

Hi! Thanks for the reply..
No, I do not get any prompt whatsoever.. I can move the mouse but cannot click on anything.. Just frozen screen, can't close a window, can't click on apple symbol on top to try to force quit an app..

My Ipad 2 won't reboot. the little circle keeps going round but the buttons don't work. help please.

My Ipad 2 won't reboot. The little circle keeps going round but that's all, it won't boot. nothing happens when I press the button on the top either. Please help.

After you hold the power and home buttons at the SAME time until the Apple Logo appears (ignore the red slider to shut down) then let go of both buttons and you don't need to do anything else. Your iPad will restart all by itself. Just be patient, but leave your iPad alone after the Logo appears.

Since I upgraded my 5c to iOS 7.1.1 my apps randomly stop working. The only way to get them to work is to power off and on. Any suggestions?

My apps including safari are randomly not able to access their servers. Then my wifi goes to E. I have to power off and on to make them work. What should I do?

Double-press the HOME button. Then flick each screen image up to terminate the application and free up its memory. When all apps have been killed. reset the phone by holding the HOME and SLEEP buttons at the same time until an Apple logo appears.

My wireless printer keeps going offline--how can I "stabilize" the connection"

my wireless printer keeps going offline--how can I "stabilize" the connection?
This question was solved.
View Solution.

Hello gerrie,
What i would do is Power cycle the printer and the router as well
-basically having them turned off for about 10-15 seconds
-and then powering back the router back on wait for all the lights to turn on completely
-and after that is back up and running i would turn the printer back on and re-establish the connection between the printer and the Wireless network
I am an HP employee.
__ if this Solution has helped Please Mark as Resolved and feel free to Provide a Kudos__

HT1339 My iPod classic shows that memory full in "other" category however there is nothing on it. I have left it connected all day and over night trying to restore it but the progress bar never goes away.

My iPod classic shows that memory full in other category however there is nothing on it. I have left it connected all day and over night trying to restore it but the progress bar never goes away. Is it shot or are there other options to restore to factory settings?

Hi pbworth,
When troubleshooting issues with iPod classic, it may be helpful to place the iPod into Disk Mode. For information on how to do so:
Putting iPod into Disk Mode
http://support.apple.com/kb/HT1363
Thanks,
Matt M.

My new macbook air and new thunderbolt monitor will not work together. the keyboard will not engage and the monitor screen keeps going black. is it a problem with the monitor, connection, laptop?

my new macbook air and new thunderbolt monitor will not work together. the keyboard will not engage and the monitor screen keeps going black. is it a problem with the monitor, connection, laptop?

A new Mac comes with 90 days of free tech support from AppleCare.
AppleCare: 1-800-275-2273
Call AppleCare. They will help you.
Best.

Airport keeps dropping the wireless connection to my network 2 or 3 times a day.

Hi,
Since apple's recent firmware update for my macbook pro, airport keeps dropping the wireless connection to my network 2 or 3 times a day. It then searches for a network but can't find it, but if I select my network manually it connects immediately ???
Any fixes for this ..... in layman's language please!
Thanks,
Steve

It is not the router. There are a number of factors that are involved. If the router is a G/N router you may have to switch to G-Only (or disable N). You may also have a 5 GHz wireless phone or other routers in the neighborhood interfereing with the signal.
Try this:
1. Open network preferences. Take note of what IP address is assigned. Then, click Advanced.
2. Click on TCP/IP and select Using DHCP with manual address and type the IP address below that.
3. Click OK.
4. Set your Router to Wireless-G only (or disable N) and change the channel to 11 or some higher number.
This should keep it from dropping the wireless connection. It is a bug in the OS. Apple has not fixed it in 3 years.
You wireless connection will be a tad slower, but you really won't notice.
Hope that helps.
DB

HT1338 The screen on my MacBook Pro keeps going black. This is happening more frequently. I have had it in to the Apple store multiple times and they can't find a problem.

My MacBook Pro screen keeps going black. This is happening more frequently. I have had it in to the Apple store several times for this and they can't find anything wrong other than it is locked up for a while. Since it is happening more and more, I am worried that at some point this will be permanent.

Has it actually happened at the store?
If not then we need to get it to do that. Now it may be completely random but you need to try and make a note of as many things as possible that happen when it does it.
How long has it been on for, what are you doing at the time, what's connected. If it's reproducible then you've at least got somewhere.

I get "an error has occurred in the script on this page" it comes up for no reason on Firefox and I can't remove the message, it then goes away on it's own after 3 minutes? how do I prevent this message coming up? I have Windows 7.

I get "an error has occurred in the script on this page" it comes up for no reason on Firefox and I can't remove the message, it then goes away on it's own after 3 minutes? how do I prevent this message coming up? I have Windows 7.
I can work the screen behind the message which stays in the centre of my screen.

Windows version is...?
What pages are giving you problems? [post links to same]
Are you getting the script errors only when attempting to print or...?
Has your printer's manufacturer confirmed that your currently installed printer software is IE11-compatible (yet)?
~Robear Dyer (PA Bear) MS MVP-Windows Client since 2002 Disclaimer: MS MVPs neither represent nor work for Microsoft

The wireless connection keeps going away and I need to power off and on the time capsule to get the wifi network up

Similar Messages

Maybe you are looking for