There are no icons in my AirPort Utility window toolbar

I am trying to add a hard drive to my AirPort Extreme. Did the hardware hook up. I then went to the AirPort Utility to set it up. According to the Help, there should be icons in the toolbar. On my version of AirPort Utility (5.5.3) I don't see any icons. Any help would be appreciated.

When connecting a USB HDD to the USB port of the AirPort Extreme, it should show up in the AirPort Utility on the Disks tab. The following is snapshot of my Time Capsule that has a WD My Passport USB HDD attached to it. Does your USB HDD not show up in the AirPort Utility?

Similar Messages

  • Where has my airport utility window gone ? when I double click on the icon all I get is an image of a globe and a base station with no options to make changes in my airport extreme.

    Where has my airport utility window gone? When I double click on the airport utility icon all I get is a picture of a globe and a base station with no further  options available to modify my airport extreme. 

    Sorry, you lost me on that last post.
    Let's start over again.
    Open AirPort Utility on your Mac
    Are you asked for a password at this point?  If yes, enter the base station or device password that you used when you originally set up the AirPort router. Depending when you did this originally, you might have been given an option to use the same password as the wireless network. If you were not, then you have a separate password for the base station.
    You need that password to be able to access the settings for the AirPort router in AirPort Utility.
    If you see a window listing basic information, click Edit in the upper right corner of the window.
    If you are asked for a password, you must enter the device password or base station password that you established when you first set up the AirPort router as explained above.
    If you forgot the password, a Soft Reset will allow you to go in and reset the base station password.  Might be a good idea to write down that password.
    If you are still stuck, then the only option that you have at this point is to perform a Hard Reset to return the settings to factory defaults and then set up the AirPort router again.
    If you prefer, you can also do a Factory Default Reset. It's the same as a Hard Reset except for the timing of holding in the reset button.

  • Is there aoss on an airport extreme? I thought there was some way via the Airport Utility?

    is there aoss on an airport extreme? I thought there was some way via the Airport Utility.

    Nothing called "aoss" is on an AirPort Extreme.
    Using the Add Wireless Clients feature under the Base Station menu (top of screen) in AirPort Utility - Manual Setup, there are provisions to add a new wireless client using a PIN or allowing the device to connect on "First Attempt".
    Whether this is compatible with "aoss", I cannot say. Please let us know about your findings if you try this.

  • On iOS 7.0.2, after web (OTA) installation there are two icons for the app on the home screen; one is invalid.

    Hello,
    I have filed a bugreport, but I am curious if anybody else has noticed this.
    Summary:
    Icon that was displaying progress of installation stays on screen next to normal icon and it is impossible to delete it or start the app with it.
    Steps to Reproduce:
    1. Full factory reset of iPhone with iOS 7.0.2
    2. Open web page with link for OTA installation.
    3. After install is finished there are two icons for the app.
    Expected Results:
    Icon that was displaying the progress should disappear after installation.
    Actual Results:
    Icon that was displaying the progress stays on screen is not usable and cannot be deleted.
    Version:
    7.0.2
    Notes:
    Configuration:
    Server used to serve the page with installation files is "Server" app on MacBook Pro with Mountain Lion.
    The same happens if other servers are used; Ubuntu 12.04 LTS.

    Hello,
    I have the same problem!
    Any idea?
    Thanks.

  • My screen is white.  There are no icons.  Any thoughts?

    Display screen is white and there are no icons, just pointer.  Tried to restart.  Could the hardware be the issue.  Only 6 months old and already had hardware restored once.

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of this exercise is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login. Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
    Be sure your Mac is shut down.
    Press the power button.
    Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
    Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
    *Note: If FileVault is enabled under Mac OS X 10.7 or later, you can’t boot in safe mode.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem(s)?
    After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

  • There are no icons displayed if a document (.docx,xlsx or pptx) is within a document set

    Hi
    I am using SharePoint 2013 SP1 with the September 2014 CU.
    If I search for documents in document libraries, they work fine and in the search results I get the Icon to the left of the text showing what type of file it is and the refiner panel shows the different filetypes are returned.
    However, if the document is within a document set which itself is inside a document library, then there are no "filetype" refiners shown and the icon to the left of the text of the search result is not there.
    Have I misconfigured somnething ?
    Regards
    Nigel
    Nigel Price NJPEnterprises

    Hi，
    According to your description, There are no icons displayed if a document is within a document set.
    For your issue, make sure you have made the Type column displayed in the library.
    Go to Library->Modify View->make sure the Type column has been selected:
    Best Regards,
    Lisa Chen
    Forum Support
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Lisa Chen
    TechNet Community Support

  • There are no icons of the apps i downloaded. I mean, I used them for a while, then my iPod died, I charged it a little, then turned it on, and saw blanks instead of apps. They work pretty fine, but there are no icons, just white rectangles. What can I do?

    There are no icons of the apps i downloaded. I mean, I used them for a while, then my iPod died, I charged it a little, then turned it on, and saw blanks instead of apps. They work pretty fine, but there are no icons, just white rectangles. What can I do?

    - First try resetting the iPod:
    Reset iPod touch:  Press and hold the On/Off Sleep/Wake button and the Home
    button at the same time for at least ten seconds, until the Apple logo appears.
    - If still problem restore the iPOd via iTunes on your computer.  First from backup and if problem persists restore to factory defaults/new iPod.

  • With the left panel, trying to use the Presets, in the tutorial to the left of the commands there are square icons, for example "Lightroom B

    With the left panel, trying to use the Presets, in the tutorial to the left of the commands there are square icons, for example “Lightroom B & W Presets”. On my program they are arrowheads pointing to the right. When I click on any Preset, it does not work.
    Also, Right Panel, Color, White Balance, “As Shot” only has 2 options (auto & custom) vs. tutorial that has 9 options.

    You are not supposed to connect a pair of speakers(as in left and right in a stereo pair)to two separate out jacks on the sound card.the place on the card where headphones/speakers with the mini jack goes is the right place.

  • HT204318 Copied my iTunes from my Mac to my Windows 7 laptop, now there are thousands of songs missing on the Windows copy with the exclamation point.

    Copied my iTunes from my Mac to my Windows 7 laptop, now there are thousands of songs missing on the Windows copy with the exclamation point. everything shows up, playlists and tracks, there are just a bunch of songs with exclamation points. how can i properly sync my iTunes from my Mac to my PC? using iTunes

    Moving a library: Quick answer if you use iTunes' default preferences settings:  Copy the entire iTunes folder (and in doing so all its sub-folders and files) intact to the other drive.  Hold down the option (alt) key (shift on Windows) and open iTunes.  At the prompt to create or choose a library choose the copied iTunes folder.

  • HT204318 Copied my iTunes from my Mac to my Windows 7 laptop, now there are thousands of songs missing on the Windows copy with the exclamation point. everything shows up, playlists and tracks, there are just a bunch of songs with exclamation points. how

    Copied my iTunes from my Mac to my Windows 7 laptop, now there are thousands of songs missing on the Windows copy with the exclamation point. everything shows up, playlists and tracks, there are just a bunch of songs with exclamation points. how can i properly sync my iTunes from my Mac to my PC? using iTunes

    nope all my songs are copied and organized into the iTunes library.

  • How can I add additional airport expresses to my system that are not being recognized by Airport utility?

    I recently purchased time capsule to upgrade my wireless system. I have 3 airport expresses in my network; I was able to reconfigure one, but the other 2 won't reconfigure.  They are not recognized by Airport utility after being reset; the time capsule and one reconfigured airport express shows up.  I would like to use the other two airport expresses to extend my wireless system. I would appreciate any help and suggestions.

    Unfortunately, you will have to use Apple's WDS setting for all of the devices on the network....Time Capsule, new AirPort Express and older AirPort Express devices.
    That is going to slow things down tremendously on the network.
    WDS only operates at "g" wireless speed, so you lose any "n" speed advantage of your newer devices.
    Worse, the bandwidth is cut in half on the entire network for each device that is set up as "relay" or "remote" on the system.
    So, the first "remote" (or relay) cuts wireless speed from 54 Mbps down to 27 Mbps. The second cuts everything down to about 14 Mbps and the third drops everything down to about 7 Mpbs. That is much slower than the old wireless "b" systems.
    Compare that to "n" speeds of 130 Mbps or up to 300 Mbps (if you are using 5 GHz) and you can easily see that you are losing more than 90% of the speed capability on the network.
    Do you even want to consider doing this?

  • Airport Extreme and Airport Express are not found on the Airport Utility.  Internet still works.  Huh?

    Good People,
    I have an Airport Extreme serving as my wireless router with an external hard drive connected to it.  I also have an Airport Express in another room connected to a stereo for Airplay.  Neither can be found on the Airport Utility (v5.5.3), but wireless internet still works.  This happens often, with both reappearing in Airport Utility for short amounts of time periodically.  What's the deal?  Both the Extreme and Express are less than 6 months old.  It's a bit frustrating not getting tunes when you have everything set up right and not being able to use Time Machine consistently.
    All recommendations appreciated.
    Thanks.

    shakeelium wrote:
    Good People,
    I have an Airport Extreme serving as my wireless router with an external hard drive connected to it.  I also have an Airport Express in another room connected to a stereo for Airplay.  Neither can be found on the Airport Utility (v5.5.3), but wireless internet still works.  This happens often, with both reappearing in Airport Utility for short amounts of time periodically.
    I've once had the same problem.
    The reason for that issue is the frequency (radio band) hopping of the station.
    On your AP-Extreme
    Enter the manual setup
    Disable Guest Network if not desperately needed
    Set a dedicated name for the 5GHz wireless (wireless -> wireless options)
    Eventually change the radio mode (if no 802.11b/g systems in your home) to "only 802.11n (5GHz) - only 802.11n (2.4GHz)" by holding down the option key *alt* while clicking on the drop down.
    On your Mac
    Disable (switch off) wireless
    Enter system configuration -> network -> wireless
    Uncheck "Ask to join new networks"
    Enter advanced options and check that your wireless name is in the first position of the list. If not, drag it with the mouse to the first position.
    Click apply
    Join your wireless again and try to connect to the 5GHz name (SSID) because the 5GHz will improve the connection speed of your Mac remarkably.
    Eventually you might change the settings on the Express too.
    Check the location of the AP-Extreme.
    It should NOT be placed: On the floor, in a corner, behind furniture, near metal objects, life high voltage wire or cordless phone bases.
    It should be placed: As high as possible (up on a shelf or ceiling mounted) with a maximum line of sight to all stations, even thru walls.
    If your home situation allows that, try to use the 5GHz band only. If you own a iPhone this must use the 2.4GHz radio.
    Lupunus

  • What are the correct Time Capsule Airport Utility Disk options?

    During configuration of the Time Capsule what are the correct options/settins in the Airport Utility on the Disk tab?  Does File Sharing interfere with Server File Saring>

    You can turn on file sharing.. it will not interfere with your server since it has a different IP address.
    You can use either device password or disk password.. do not use the profiles as that complicates things.. and Apple did not build in a link to Server to use standard user login which is a great pity.. when you have an active directory type setup it .. the TC could have been made a lot more business like.. However apple really have the TC aimed at the domestic market and users without a server.
    What are you intending to use the TC for?
    Most people would be better buying an airport extreme rather than TC when they are running business setup.

  • ITunes/Airport Utility Windows cannot connect to Airport Express

    I really hope someone can help me with this since I have spent 2 days trying to get my new Airport Express to stream music with no luck yet.
    I have a wireless network using Netgear WGR614 with WPA security settings. The AE has V6.3 firmware update and I used the Airport Admin 4.2 to set it up. I tried all the recommendations here and connected the AE to the router LAN port using ethernet cable and did a factory default reset. I then configured it to join my existing wireless network providing the WPA details.
    That is when the problem starts. After successfully updating and rebooting the AE shows solid green LED. However, using Airport Admin to connect fails intermittently with error -6753 asking me to check my network settings even though they are fine. If I try a few more times, it connects and I am able to enter and modify settings. When doing another update, it again fails with error -6753, but a few retries later, it does go through. Note that all this time, the ethernet cable is still connected to the AE even though it is setup to connect to my wireless network.
    Now, I unplug and relocate my AE near my stereo - it starts up fine and shows solid green light. My router "attached devices" page indicates that the device is connected with the DHCP ip address of 192.168.0.3. However, when I now try to use Airport Admin, it ALWAYS gives me the connection error -6753. The AE shows up in iTunes, but when I connect to it, it just hangs and after a minute or so, just gives up and goes back to the "Computer" speaker.
    I tried to do a ping on the ip address, and it gives me "Request timed out". I thought maybe it is my laptop interfering so I did ensure that I turned off ALL firewalls, but the problem still remains.
    So in short, AE seems to be joined and connected to my existing wireless network (green light), but neither Airport Admin nor iTunes nor ping utility can even communicate with it; and it seems to be due to the error -6753. I have tried pretty much every advise regarding connecting via wired etc. and nothing seems to work. This is not a wireless interference issue too, because the error also appears when connected via cable.
    Any help really appreciated.
    Thanks.
    R

    Thanks for the response. Here is an update:
    I tried to connect to the AE from another windows laptop...and it worked. So it seems that it is only my laptop that cannot connect to the AE. The only difference is that I used my laptop to initially connect to the network created by the AE, and after that I could never get it to connect.
    Interestingly, when I did manage to get into the AE and check its log, here is what I find...
    Jan 1 00:00:00 5 Configuration updated.
    Jan 1 00:00:01 5 Initialized (firmware 6.3).
    Jan 1 00:00:15 5 Joined BSS 00:09:5b:fb:7c:7a
    Jan 1 00:00:16 5 Installed unicast TKIP key for authenticator 00:09:5b:fb:7c:7a
    Jan 1 00:00:30 5 Internet configuration leased (host 192.168.0.3/24 gateway 192.168.0.1 dns1 192.168.0.1 domain innomedia.com lease 7776000).
    Jan 1 01:14:29 5 Disassociated with station 00:09:5b:fb:7c:7a (message integrity error).
    Jan 1 01:14:38 5 Disconnected from network.
    Jan 1 01:15:31 5 Joined BSS 00:09:5b:fb:7c:7a
    Jan 1 01:15:31 5 Installed unicast TKIP key for authenticator 00:09:5b:fb:7c:7a
    Jan 1 01:16:14 5 Internet configuration leased (host 192.168.0.3/24 gateway 192.168.0.1 dns1 192.168.0.1 domain innomedia.com lease 7776000).
    Jan 1 01:27:18 5 Connection accepted from ::ffff:192.168.0.6/1153.
    Jan 1 01:27:24 5 Connection accepted from ::ffff:192.168.0.6/1154.
    Jan 1 02:35:43 5 Deauthenticated with station 00:09:5b:fb:7c:7a (leaving network).
    Jan 1 02:35:43 5 Disconnected from network.
    Jan 1 02:35:49 5 Disassociated with station 00:09:5b:fb:7c:7a (message integrity error).
    Jan 1 02:35:49 5 Joined BSS 00:00:00:00:00:00
    Jan 1 02:35:51 5 Deauthenticated with station 00:09:5b:fb:7c:7a (4-way timeout).
    Jan 1 02:35:51 5 Disconnected from network.
    Jan 1 02:35:59 5 Disconnected from network.
    Jan 1 02:36:52 5 Joined BSS 00:09:5b:fb:7c:7a
    Jan 1 02:36:53 5 Installed unicast TKIP key for authenticator 00:09:5b:fb:7c:7a
    Jan 1 02:37:07 5 Internet configuration leased (host 192.168.0.3/24 gateway 192.168.0.1 dns1 192.168.0.1 domain innomedia.com lease 7776000).
    Jan 1 02:50:49 3 Administrative access denied to ::ffff:192.168.0.2/2397.
    Jan 1 02:51:08 3 Administrative access denied to ::ffff:192.168.0.2/2400.
    The administrative access denied is pointing to my laptop, whereas the connection accepted was the other laptop from which everything works. So it seems that the AE is specifically not allowing my laptop to talk to it! Given that my AE is being connected in Client mode, there are no settings I can access to see why it has singled my laptop out.
    Any help appreciated.
    Thanks
    R

  • Airport utility windows 7, airport utility windows 7

    Dear Sir,
    I have a Windows 7 64 bits. The AirPort Utility installed correctly with no error but I can not see my TC and AE. ("AirPort Utility was unable to find any AirPort wireless device ...")
    On another PC with Windows XP SP3 Airport Utility works correctly and I see Time capsula OK.
    Can you help me with Windows 7.
    Best regards,
    Alex

    UPDATE
    * I located the IP address and admin password of the airport extreme and was able to log into to the (File / configure other) airport extreme.
    I believe it's a W7 bonjour issue.
    As you can see in my attachments, Bonjour is installed however msconfig running services show it as stopped. I can't get it to start.
    ** How can I force bonjour to start? **
    Here are my replies to your recommended steps:
    What version extreme are you talking about? Actual model A1xxx from the base is a big help.
    - I forgot to check this
    Step 1.. Ping.. Ping is your most important tool to find things on a network.
    Open a command window and type ping 10.0.1.1 (or whatever is the current IP of the extreme).
    - Yes, I can ping it.
    Please turn off all firewalls.
    - Yes, firewall is off
    Make sure the win7 is not in homegroup.
    - done.
    Make sure win7 is set to home.. not work or public for location of the network.
    - done.
    Step 2. .. This assumes you now have ping response.
    In whatever airport utility you like, reset the extreme to use all SMB names.
    - WHERE do I make these changes?

Maybe you are looking for