There is no communication between devices which are connected to Linksys Wireless WAP4410N Access Point ?

Dear all,
     I deployed new Linksys Wireless WAP4410N Access Point and it is working fine. Laptop which is connected to AP can able to access internet. It can able to communicate with AP and also the gateway IP(Router IP) but the issue is wireless devices are not able to communicate between them. In the case LAN device can communicate between wireless devices. Can't able to share files between wireless devices.
     Please help me to troubleshoot this issue. Wat could be the issue over here. Wat step i have to take to clear this issue.
     Advance in thanks.
Thanks and regards,
Chandhuru.M

Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Thank you for using the Cisco Community Post Forums.
Under Wireless/Security how do you have the Wireless Isolation configured?
Wireless Isolation (within SSID) should be disabled to allow wireless computers associated to the same SSID to see and transfer files between each other
Thanks
Eric Moyers .:|:.:|:.
Cisco Small Business US STAC Advanced Support Engineer
CCNA, CCNA-Wireless
866-606-1866
Mon - Fri 09:00 - 18:00 (UTC - 05:00)
*Please rate the Post so other will know when an answer has been found.

Similar Messages

Can we get the list of Devices, which are connected to same Wifi?

HI All,
I am working with an iOS App which is related to Wifi-Network. I need to list out all the devices which are using same wifi connection, is there any way do. I have seen the Apples CaptiveNetwork, usinf that I can get the connected Wifi Info like SSID & BSSID, But I need fetch other devices info. I wanna connect to that device through wifi. Can anyone share with me please. Thanks in Advance.
--Rajesh.

You can't. That information isn't available to an app.

How can i check the devices which are connected with my AirPort Express?

I saw an unknown device in the app 'Who Uses My Wifi?', how can i check it through AirPort Utility and can i remove this device by the app?

Open AirPort Utility
Hold down the option key on your Mac while you double click the picture of the AirPort router
Currently connected wireless ciients will be displayed
Don't forget about the wireless printer you might have, baby monitor, wireless thermostat and other items that connect using wireless. They will appear on your check.....not just computers or iPhones, etc.
If you have 3 wireless devices, and you see 4 devices connected, you may have an unwanted guest.
If you are using good wireless security, like WPA2 Personal, and a good password, it is extremely unlikely that another device will be on your network

I have an iphone and an ipad (which are connected by the same apple id) i broke the phone and sold it but i didnt get to factory reset it because it was broken, is there any way for me to wipe my iphone from my ipad?

i have an iphone and an ipad (which are connected by the same apple id) i broke the phone and sold it but i didnt get to factory reset it because it was broken, is there any way for me to wipe my iphone from my ipad?

Try this:
Open the "Find my iPhone" app on your iPad, fill in your AppleID and password at the start up screen, and you should see a list of all your devices and their current location, if connected to a Wi-Fi or mobile data network. Devices not connected will be shown as "offline". But you can still trap on the icon and hit "erase iPhone" in the right hand window.
If your iPhone is not listed, you did not activate this feature during the setup of the phone and it can't be erased remotely.
If the phone is listed, even as offline, tap on "erase" to send the erase command. The next time your device will be connected to any kind of network, the content will be erased.

How can i see which devices are connected to my wireless network?

how can i see which devices are connected to my wireless network?

Login to your router and view the DHCP clients.

Hi there, i installed a system update earlier on my MacBookPro and now it wont connect to wi-fi, working through Network Diagnostics hasn't solved the issue. all other devices here are connecting normally. any ideas?

hi there, i installed a system update earlier on my MacBookPro and now it wont connect to wi-fi, working through Network Diagnostics hasn't solved the issue. all other devices here are connecting normally. any ideas?

Hi, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
10.4 instructions...
Is that Interface dragged to the top of Network>Show:>Network Port Configurations.
If using Wifi/Airport...
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6/10.7/10.8, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.

I Wanna See All Devices That Are Connected To My Router

I have a E1200 router and it's pretty good however I've noticed that there are 12 devices connected to my router when infact there should only be 4 devices connected. I would like to see all the devices that are connected and disconnect the ones that don't belong HELP!
Solved!
Go to Solution.

Are you using a software to see all devices that are supposed to be connected to your router? You can reset and start over with your router. Make sure you have a security enabled on it like WPA Personal. You can try DHCP Reservation as well to ensure that the devices that will have access to your router are only the ones you included on the list.

Gilson 307 pump which are connected via a system interface module 506C

hello,
I have a master's thesis received the task to control gilson pumps.
Unfortunately I have no experience with LabView.
It is generally possible to steer the pump? I read a lot and it will describe this is not possible. But I have a compoliertes Pogramm and unfortunately can not get the source code and the driver. There you can control the pumps.
Can one of you help. I would be very grateful.
hardware:
three Gilson 307 which are connected via a system interface module 506C. The interface module is connected via an RS232 connection.
LabView 2012
Thank you very much in advance and best regards
Michael

Thanks for the extra comments GerdW.
Perhaps there is someone who wants to help me, in the manual are not the commands available. Even the technicians of Gilson I could not tell from his documentation of the command sets.
many greetings
Michael

I have a canon AirPrint printer an iPad 4 Which are connected to the same wifi connection but will not work any ideas

I have a canon airprint printer new + an iPad 4 also new which are connected to the same wifi router but the iPad cannot find the printer no matter what I do I can't find the printer ? Any idea's

You don't mention the router model but some Thompson routers appear to have a problem working with Bonjour/mdns. There's some information here:
http://blog.hosk.in/2011/01/telecom-nz-thomson-tg585v8-with-apple.html

How can I know which clients are connected to my network through express and which are connected through extreme?

I have an airport express extending, through wireless, a network provided by an airport extreme. How can I know which clients are connected to my network through express and which are connected through extreme?
Here you can see both routers:
I would expect to some clients connected to the express, other than the extreme. And that's all I see: only the airport extreme appears as client of the airport express.
Below, one can see the summary of the config for both routers.
Would somebody explain it?
Thanks,
Marcelo
Message was edited by: Marcelão

please disregard this answer.
Message was edited by: Marcelão

How to see all devices that are connected to Apple ID

How to see all devices that are connected to Apple ID

Are you using a software to see all devices that are supposed to be connected to your router? You can reset and start over with your router. Make sure you have a security enabled on it like WPA Personal. You can try DHCP Reservation as well to ensure that the devices that will have access to your router are only the ones you included on the list.

HT1420 How do you find list of actual devices that are connected to your itunes account? I'd like to know before deauthorizing, exactly what devices it is showing as connected

How do you find list of actual devices that are connected to your itunes account? I'd like to know before deauthorizing, exactly what devices it is showing as connected

Click here and ask. If the iTunes Store staff doesn't give it to you, no.
(86004)

HT204291 Does mirroring automatically mirror content to other devices which are registered under the same name ? If so does this occur across different distances? Does Apple Tv store mirrored content?

Does apple tv automatically mirror content from one device to all other iPad or mackbook devises which are registered under the same name? If so does a device have to be in the same area ?

Welcome to the Apple Community.
Mirroring only works FROM a mobile device TO an Apple TV.

Can I disable photo stream from select devices that are connected to my iTunes account?

Hello, I was wondering is there any way to do this because I have three iPads connected onto my account, one is in another country and one my parents own, but for my personal one, I would like to disable this feature so my pictures don't get uploaded. My parents like to see the photos being taken by family in another country and I would like those two devices connected only.

You can turn off photo stream on one device without effecting the others. If you want to keep the photo stream photos on the device you are going to turn it off on, you will need to same them to your camera roll before doing so. To do this open the my photo stream album, tapping Select, tapping the photos, tap the share icon (box with upward facing arrow), then tapping Save to Camera Roll. Then go to Settings>iCloud>Photos and turn off My Photo Stream. This will delete the photo stream photos from this device, but not the others (and you already saved copies of these photos to your camera roll so they will still be on your device).
The other two iPads that are signed into your iCloud account with photo stream enabled will still be sharing the same photo stream but you will no longer see it, and your photos will no longer be added to the stream. They can still share photos with you by adding them to a shared stream and inviting you as a subscriber (as explained here: http://help.apple.com/icloud/#/mmc0cd7e99).

Some devices able to connect to the wireless and s...

So I recently decided to reset my lenovo laptop to factory settings using the lenovo one key recovery. Unlike before, I now cannot connect to my bt infinity wireless or wired internet. It say limited connection but won't allow internet access.
I then realised that several devices are connected and working with the home internet including computers, ipods etc (all of which have been connected before I reset my laptop). But any new devices (including my ps3 and ipad) will not connect and have the same problem as the laptop.
please someone help!

If you've never changed any settings on the hub, bar the admin password, I'd factory reset it - http://bt.custhelp.com/app/answers/detail/a_id/11386
Then see if those devices that couldn't connect now can.
-+-No longer a forum member-+-

There is no communication between devices which are connected to Linksys Wireless WAP4410N Access Point ?

Similar Messages

Maybe you are looking for