Thermaltake Silent Purepower 480W for K8N NEO4 Platinum

after much debacle of what psu to propel my MSI K8N NEO4 Platinum (Non SLI model) it has become clear to me that the only real choice i have within my reach is the thermaltake silentpurepower 480w, this is simply the best power supply i can get down here (Colombia, South America) and the most expensive one too.
i have done my fair share of research on the matter and have found a number of people using this power supply to power systems based on the K8N NEO4 Platinum, even some have been bold enough to use the SLI version of the board with this power supply.
so i guess its go for broke time on the matter, any feedback ?

Quote from: Stick on 26-January-06, 23:13:33
i have the buterfly model http://www.thermaltakeusa.com/2005/purepower/W001920.htm
it has a 20 pin connector and a 20 to 24 pin convertor, so you can plug it in both ways
from what ive seen its the same psu with different accesories, but its the same psu, so i guess this is it. Im gonna connect the 20pin to the 24 connector in the motherboard as those 20 to 24 adapters dont seen to generate any kind of trust in me, i guess as long as i keep my present setup and i dont overclock everything should run just fine.
many thanks...

Similar Messages

Thermaltake Silent Purepower 480W

Hi.
Cannot find a psu compatability list to say if this psu "Thermaltake Silent Purepower 480W" is ok with MSI K8N SLI Platinum
http://www.thermaltake.com/purepower/W001314.htm
Does anyone know
thanks for any help

I swear, people have one bad experience with a brand and automatically assume that they are all bad. I have never seen a power supply, motherboard, or any other part that didnt have a DOA every now and then. This is just a fact of the electronic world. I have personally built and used over 10 different high end Athlon 64 computers (both 754 and 939) that used Thermaltake power supplies (Ive also used PCP&C, OCZ, . Included models were the TR2 430W, dual rail 460w, older style 480w, and the 560w. Out of all that i had one 560w come with a 12v that was a little low, about 11.6. The rest of them, including the 560 replacement, have been rock solid. All of them run within 2% of spec all the time. ATX psu's actually only have to be within 5%.
So to say that they arent any good for amd64 is so much garbage. For running machines at base speeds and even modest overclocking, they are perfectly fine. For REAL overclocking, sli, or lots of hard drives get an OCZ 520SLI, silverstone 600, or any PC Power & Cooling (the absolute best but expensive as heck). Also, all of TT'S new models have dual 12v rails with definately more 18a. Research is a wonderful thing.
The most impressive unit of theirs that i have used was the 460w woo68 with dual 15amp 12v rails. Had it powering
amd 64 3700
msi k8n neo4-f
2x512 ddr400 patriot 2-3-2-5
zalman 7000b cu
80gb hd
250gb hd
sapphire x800xl w/ zalman vf700
nec dvd burner
lite on dvd reader
creative x-fi platinum
hauppauge wintv pvr350
modem
and 3 case fans
all night bf2 session and psu exhaust air was always cold and rails always great.
The 560 that user is having trouble with is most likely just a DOA like the tons of Antecs, Seasonic's, Enermax's, and even OCZ's that i have read about. Crap happens, RMA and forget about it.

Largest SATA drive for K8N Neo4 Platinum

I have a system based on the K8N Neo4 Platinum board, I'm planning to up, the storage capacity of my rig and was wondering if I can install a 500 GB or larger SATA or SATA II drive on it?
to make long story short I would like to know whats the largest Hard Drive (either IDE or SATA) one can install on a system with this board without problems or compatibility issues.
I presently have a Maxtor Diamond Plus 80GB SATA drive,
Any takers??? ???

I see no problems, just try it.
As for a Sata-II drive, don't take Maxtor, any other drive should be fine.
However, you maybe must jumper it to SATA-1, depends on the onboard controller.

X2 3800+ (E6) support for the K8N Neo4 Platinum/SLI

Hi everyone:
I have decided to purchase the K8N Neo4 Platinum/SLI (MS-7100-020) and I ready placed the order. However, I wonder if it supports the AMD X2 3800+ (E6 Version) CPU? The reason I asked the question because I found the following table from the Taiwan MSI web site which shows that X2 3800+ E6 is undertesting.
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=641&kind=1
Thank you for any replies.

Mine worked, ran for 2 weeks already at stock, tried & ran to 2.2GHz on stock HSF with no problem.
Using X2 3800+ E6, MSI K8N PLI Platinum mobo, 3.7 bios & Inno3D 7800GTX single latest nvidia 78 drivers, 2x512MB DDR400 CL2.5 Kingston Ram, Hitachi T7K250 Sata 250GB HDD, NEC ND-3530A Benq 1640, , Silverstone Zeus 650W PSU
At first I have this concern too, but tried it anyway.
See my screenshots for your info.

Building system for friend with K8N Neo4 Platinum

MSI K8N Neo4 Platinum
AMD Athlon 64 3200+ Venice (ADA3200CGBOX)
CT2KIT12864Z40B (2x1GB)
eVGA 256-P2-N516 (7800GT)
WD2500KS (250GB SATAII HDD)
ATXA9N-SS/500 (Case)
Aspire 120MM
Aspire 80MM
ND-3550A (DVD-RW)
TG-480-U22 (PSU)
Can anyone recommend BIOS and drivers I should preload to a CD? I would rather not install from retail CDs only to download new ones.
Are there any other concerns or things I should know of?
Thanks!

Quote from: Kwea on 10-January-06, 23:21:38
MSI K8N Neo4 Platinum
AMD Athlon 64 3200+ Venice (ADA3200CGBOX)
CT2KIT12864Z40B (2x1GB)
eVGA 256-P2-N516 (7800GT)
WD2500KS (250GB SATAII HDD)
ATXA9N-SS/500 (Case)
Aspire 120MM
Aspire 80MM
ND-3550A (DVD-RW)
TG-480-U22 (PSU)
Can anyone recommend BIOS and drivers I should preload to a CD? I would rather not install from retail CDs only to download new ones.
Are there any other concerns or things I should know of?
Thanks!
You can use CD drivers (if needed to get connected to net) and update. because of the item on CD will be out dated
I'am using V1.09 BIOS, Nforce 666, GFX 7772 works good for me

K8N Neo4 Platinum random lock-ups and BSOD

I built a new PC about 3 months ago and from day 1 it has always locked up / frozen at random intervals. Sometimes it also BSOD's with a Machine Check Exception. Seems to lock up / freeze more often when have multifple windows open eg. Multiple IE running but really is random. I have replaced the Mobo and Ram but keep having the same issues. Have tried a clean install but no luck either. Did a clean install on an old IDE HDD and seemed fine but it did not have all of the software that I run on the SATA drive. Thinking the SATA drive may be the issue? Please Help!!!
System is as follows:
MSI K8N Neo4 Platinum [Bios 1.D]
AMD Athlon 64 X2 3800+ DC [AMD Drivers]
2 x Kingston 1024Mb ram [Dual Channel]
Nvidia 6800 Ultra [Latest Drivers 91.31]
Thermaltake Purepower 460W PSU +3.3V 30A, +5V 30A +12V 15A
Western Digital 200G SATA II HDD [SATA Port 5 i think]
1 x LG DVD +-R/RW [IDE Master] IDE port closest to edge of Mobo
1 x LG CDR/RW [IDE Slave]
MS XP Home SP2

Quote from: davePC on 09-August-06, 09:06:44
Did a clean install on an old IDE HDD and seemed fine but it did not have all of the software that I run on the SATA drive. Thinking the SATA drive may be the issue? Please Help!!!
Seemed fine?
There isn't really be any difference between an IDE drive and a sata.
Except that the sata drive needs some drivers as your installing the os.
Check your ram timings in bios but likely it's your psu.
Which components are on which rail?
The ones that use the +12v are your cpu,cdrom,dvdrom and graphics card.
Try disconnecting both roms and see if it improves things?

BSOD's on my x64 K8N Neo4 Platinum based PC, Any ideas what's wrong? Help!

Over the past few month I've been getting BSOD's. There is no real pattern to their occurence and it's not something which is constantly happening (It happened around 5 times in the past 2 months), but I've really grown to hate them. You see, after getting one what has happened in the past is that when I go to restart my pc after getting a BSOD, I find I need to re-install my whole OS! What happens is that after booting (which oddly enough doesn't work well after a BSOD, It freezes on the boot screen and I need to restart several times), a black screen appears telling me that certain files in the C:Windows\ direcotory are corrupt or missing.
So the real problem is that the BSOD's cause me to re-install my whole OS. One will happen, then it will be ok, I turn the system on, log into windows, then it might happen again, after which I'll need to re-install. The files that go missing are always different too, and when I run scan-disk (after plugging in my main drive into another computer) it finds corrupt files and deletes them.
At first I thought it was Azureus (p2p client) which was causing the problems because it seemed to happen when I was runing that. I stopped using it, and the BSOD's still occured...sometimes randomly when browsing...etc. I figured that since files got deleted and corrpupted, it must be a problem withthe Hard Drive....So I bought a new one, and I've still had the BSOD error (although files haven't been deleted yet).
So yeah, I really need to solve this problem as it is taking away from my productivity and causing me to re-install far too often. I will post the BSOD info as well as my system info below (and a screen shot):
Quote
MACHINE_CHECK_EXCEPTION
*** STOP: 0x0000009c (0x0000000000000004,0xFFFFF80000113BC0, 0x00000000B2000000, 0x0000000000070F0F)
I looked that up on the net, and it seems the first part seems to indicate, or at least COULD indicate overheating. I checked CPU and System temps and they seem acceptable.
I am running Windows XP x64 Edition with the following hardware (please note that all of the hardware drivers I'm using are written for x64, MSI is so good:)). I have had this PC before it started having these problems, it could be related to using x64 I guess, but the error doesn't show that does it?
Quote
AMD Athlon 64 3200+ 2.0 GHz Socket 939 (Venice Core) w/ stock heatsink/fan
MSI K8N Neo4 Platinum S-939 nForce4 Ultra
OCZ PC-3200 DDR400 Premier Series 1GB (2x512MB) Dual Channel Kit CAS 2.5
Ati Radeon x800xl 256MB gddr3, PCI-E
LG 17" L1720B LCD monitor 16ms, 1280x1024
Western Digital Caviar 120GB SATA
Western Digital Caviar SATA II (WD1600JS) 160GB 7200RPM 8MB Buffer
Western Digital Caviar SATA II (WD2500KS) 250GB 7200RPM 16MB Buffer
Pioneer DVR-109 DVD-RW
Pioneer DVR-110D DVD-RW
Antec Sonata II Mid tower ATX black power supply 450 Watt ( ATX12V 2.01 )
Creative I-Trigue 2.1 L3450 speakers
Sony 1.44MB Floppy Disk Drive
Microsoft multimedia keyboard and Microsoft optical mouse (PS/2)
My OS and drivers are fully updated. As for my BIOS I've been running the version I'm using now forquite some time and I believe it is version 1.5. Also in another bad turn of events, my northbridge fan seems to be on its way out of this world (this just happned so I don't think its related to the BSOD). I haven't been able to find a replacement, and since its not spinning very fast, and sometimes stops...It's causing the heatsink to get quite hot. I need to get a new one, and I can't find them anywhere...I wonder if thats covered under warranty... I looked into getting a different heatsink, but my Graphics card is so colse to this heatsink, that theres no room for a bigger one at all.
Do you think this problem is motherboard related, I cannot understand what the technical info the BSOD gives me means, can anybody understand it? I don't think its my HD's, or Ram, or CPU...could it be a motherboard problem? And if so, its under 1 year old, can I get an RMA?
Thanks for the help in advance.

At one time I had a weak 450w psu that had only 18a on the 12v rail. When I overclocked my cpu and gpu, I was getting bsod's every once in a while and couldnt figure it out until I read a similar post like yours on this forum. I decided to upgrade my psu and havent had that problem since.
Power supplies can be deceiving. I now have a 480w psu but its has 30a on the 12v rail. So what we need to know is the ratings of your psu (see my sig) just to see if your psu is the culprit. Just my 2 cents.

Constant HDD access (K8N Neo4 Platinum)

Hello all, this is my first time posting on these forums.
A couple of days ago I put together a new system for myself, with the following components:
* Athlon64 3200+ processor
* MSI K8N Neo4 Platinum motherboard
* 1Gb RAM
* Gigabyte 128Mb GeForce 6600GT graphics card
* 2x Seagate 250Gb 7200rpm SATA drives
* LG IDE dual-layer DVD-RW drive
* Apacer 7-in-1 internal USB 2.0 card reader
* Thermaltake "soprano" ATX midi-tower w/ 400W PSU
The two hard drives I have connected to ports SATA5 and SATA6 on the motherboard and set up in a RAID1 configuration (using the on-board Silicon Image SiI 3114 RAID controller). I then installed Windows XP Professional, which went on fine. The only problem I have now is that the hard drives are being constantly accessed by the system, even when I'm doing nothing on the system. This isn't just an occasional access once every second or so, the little HDD LED just flickers away merrily the whole time. I have run both filemon and diskmon on the system, and found that while no particular files appear to be being accessed, there is almost constant write activity being performed to the hard drives.
I have narrowed it down to somehow involving the Windows XP RAID drivers. If I boot from the Windows XP install disk and load the third party drivers for the SiI 3114, I get the constant disk access when sitting at the first screen of the install process ("Welcome to Windows XP" text-only screen). If I do the same without loading the drivers (thus Windows does not recognise the RAID drive), no disk access. I have tried updating the RAID controller drivers under the Device Manager (now up to version 1.2.0.0), but it does not fix the problem. I have done a full virus and spyware scan (bearing in mind that this is a clean install), with no results. I have checked all running processes and services (including making sure Indexing Service is not running), but have been unable to find anything that could be causing this constant activity. I have yet to try actually breaking the mirror and running the drives off the normal SATA controller. I will be trying that tonight when I get home if no other solution presents itself, but obviously I would rather get it behaving properly in RAID1 if at all possible.
It's driving me crazy. There doesn't appear to be any actual issues with the performance of the machine, but the constant hard disk activity can't be good for the drives long-term. I have searched these forums for a possible solution, and while some people have had similar problems, none of the suggested solutions have worked for me so far. If anyone can help me with my dilemma, I would be Eternally Grateful(tm).

Yes! At least I'm not alone... constant disk ticking is driving me nuts too.
I have same issue with a newly built system - different board but Sil3114.
My C: is on the NF4 SATA interface, but I have 4 250GB Seagaets on the Sil3114, intended for a RAID5 array. Having installed XP, I've become distracted by the constant disk access and have been trying everything to eliminate it before proceeding with the rest of the build - nogo. Your post gave me the clue - boot with Sil3114 disabled = no disk activity; boot with enabled = constant disk flogging.
I've got the Sil driver up to 1.2.3.1 but no better. Suspect it may be the Sil3114 BIOS that needs upgrading but seems no way to flash it - have you got anywhere with your debugging?
Appreciate a solution before I go crazy with the tick, tick tick....

K8N Neo4 Platinum - fan replacement

I have a 2 month old K8N Ne04 Platinum edition (not SLI) motherboard. At first the system was dead quiet, however the NForce4 Ultra's stock fan has become increasingly loud over the last week, to the point where I can no longer hear myself think.
Can a new fan be ordered and attached to the existing heatsink, or does the whole unit need to be replaced? I have no idea what 3rd party part would be compatible, any pointers would be greatly appreciated. Thanks!

Quote from: Iceman81 on 07-July-05, 07:30:38
Hello there, I too had the same problem after 1 month of having the K8N Neo4 Platinum Motherboard. All was well and silent then all of a sudden the NORTHBRIDGE fan started clattering and getting very loud to which was very disturbing.
The only way around this is completely taking out the "MSI" provided NORTHRBIDGE fan by removing the motherboard from the case and pressing on the clips on back of the board that hold the fan and then popping in a new NORTHBRIDGE fan/cooler. I found a great replacement for the cheapie MSI provided fan in the "VANTEC CCB-A1C Ball VGA COOLER" which is all copper based and purchased from www.newegg.com for under 15 US dollars shipped.
Below is the picture of what the fan I recommend looks like...
I have since been using the "VANTEC ICEBERG COPPER COOLER" and the NForce4 chipset has been running very-very cool and was a perfect fit!
Take care, Ice!
Sorry to revive an old thread but looking at my problem and how often it was that question asked here, I want you to help clear things up...
Is this Cooler you are referring to, this one? The same model and everything?
http://articulo.mercadolibre.com.ar/MLA-23998289-cooler-chipset-o-video-vantec-iceberq-modding-_JM
Because if it is, I can buy it here knowing I will have that cooler replaced...
Another thing, Which is better? Titanium or copper? cos the titanium one is cheaper...
Thanxs a lot for helping me out pals...
EDIT: Sorry, pal... Didn't mean to offend anyone

K8N Neo4 Platinum as HTPC mobo questions

I've been looking at building a Home Theater PC (HTPC) for a little while now and have been investigating various parts, including possible motherboards. The MSI K8N Neo4 Platinum is a key canidate and I was wondering if I could get some advice from people who actually use the board as to whether it would be suitable. Here is the basic run down of what I need:
1) I have read that there are potential issues with the AMD 90nm cores. It seems a lot of people in the forum are running them though. Has the problem been cleared up with the latest BIOS? (I am looking at using at least a 3500+ Venice core, but might try to go a little higher).
2) The board has a cooling fan on it, How loud is it? (The goal is to try and make the system as silent as possible without going over budget)
3) Front side Firewire connector - it seems like its located between two PCI slots. Has this posed a problem?
4) The PCI slot "reserved" as a comm slot - is it usable for other PCI devices? (One reason this board is on the short list is that it has 4 PCI slots. I plan on putting in at least 3 tuner cards, possibly 4 or using the 4th for a sound card or some other device. Thus, having this slot available as a general purpose PCI is important. Some retailers claim it is 'reserved' others don't.)
Any other recommendations would also be appreciated. Especially as concerns silencing and processor choice.
-Watson

Quote from: watson on 08-March-06, 00:54:50
1) I have read that there are potential issues with the AMD 90nm cores. It seems a lot of people in the forum are running them though. Has the problem been cleared up with the latest BIOS? (I am looking at using at least a 3500+ Venice core, but might try to go a little higher).
There were, make sure u get a E4 revision or higher. 99,9% of CPU's shipped today will have that.
Quote from: watson on 08-March-06, 00:54:50
2) The board has a cooling fan on it, How loud is it? (The goal is to try and make the system as silent as possible without going over budget)
Very, I have the same fan. I run it at 5v, than it's OK, u can get an adapter in most PC shops. Getting a passive haetsink is also a possibility, but that will void your warrenty.
Quote from: watson on 08-March-06, 00:54:50
3) Front side Firewire connector - it seems like its located between two PCI slots. Has this posed a problem?
Dunno, Don't see why, make sure u get a HTPC with a front bracket with a FW port.
Quote from: watson on 08-March-06, 00:54:50
4) The PCI slot "reserved" as a comm slot - is it usable for other PCI devices? (One reason this board is on the short list is that it has 4 PCI slots. I plan on putting in at least 3 tuner cards, possibly 4 or using the 4th for a sound card or some other device. Thus, having this slot available as a general purpose PCI is important. Some retailers claim it is 'reserved' others don't.)
Hmm, my gues is that that would be a problem.
Quote from: watson on 08-March-06, 00:54:50
Any other recommendations would also be appreciated. Especially as concerns silencing and processor choice.
See if this will fit in ur HTPC (the 80mil one)
http://www.coolermaster-europe.com/index.php?LT=english&Language_s=2&url_place=product&p_serial=RL-MUA-E8U1%20/%20EBU1&other_title=+RL-MUA-E8U1%20%2F%20EBU1+AQUAGATE%20Mini%20R80%20%2F%20R120
Underclocking and undervolting will also help keeping the CPU cool = less need for noisy fans.
Be weary of components causing heat. Samsung HDD's are the coolest, use as many as the onboard stuff as possible, etc..
Stick to 1 casefan and put it on the NB-FAN, so Corecenter or Speedfan can manage the fan speed. Recomended brands are Papst, Panaflo and Vantec Stealth.
4GB limit is due to having a 32bit OS. With 32bits u can only adress a max of 3GB. It might work using XP 64-bit, but I don't see why a anyone would need it.

K8N Neo4 Platinum power on/off problem

Hi all.
I just got a K8N Neo4 Platinum, and have a problem with switching it on and off.
When I switch on the mains to the PC PS(before turning the PC on), the fans start turning, and I hear disks spinning up. The PC power LED is off, but the HD LED is on. There is no picture on the monitor.
If I then switch the PC on, it boots normal, power LED is on, and the HD LED is normal. The PC is working absolutely normal, with winXP.
But when I turn the PC off again, the fans remain on, power LED goes off, HD LED on. And I can't switch the PC on again, till I have toggled the mains supply.
I have tried measuring what comes on the power connector. It looks like there is still 12V when the PC is supposed to be switched off. Don't know if that is right.
There is also 5VSB and PWR OK, but I think they are supposed to be there.
I hope I have been able to explain the problem in understandable english.
Jens G

Quote from: fflex on 02-March-05, 19:21:07
That the comp turn itself on when the different front side connectors etc isnt in, i dont think that's a problem with ur PSU.
Same thing happend to me when i forgot to plug them in a couple of days ago. I got a Tagan 480W, and its flawless!
Have u ever considered unplugging everything, and doing it from the beginning? ......
I have tried from the beginning many times, but it's always failing.
BUT..... Today I got a new K8N Neo4 Platinum from a vendor next door to where I work, and it works perfectly
I had a suspicion that the motherboard was causing the fail, but couldn't be sure without trying a new one. Now the first one is going back to the shop where I bought it.
Thanks to all for all the suggestions you have come up with.
Jens G

K8N NEO4 PLATINUM WONT TURN OFF WHEN SHUTDOWN

Hello,
I recently built a system for my friend and he wanted the following setup. Everything works good, but when he selects Windows to shutdown, the OS goes through regular procedures, then the screen fades to black. However, the fans keep running and the PSU is still live..... so it seems the system isnt shutting down 100%. I have seen this issue before, but dont remember how to fix it. Something to do with the registry or within the system, alas, i cannot remember. please assist.
K8N NEO4 Platinum SLI Mobo
AMD 3500+ Venice Core processor 939 chipset
Antec TruePower PSU 480W
2 x 512 Corsair PC3200 RAM
Antec case
2 x Evga 6800gt ultra video cards
2 x Hitachi 80GB Sata II drives in a Raid 0
1 x NEC DVD/R/RW drives
Windows XP Pro OS

Have you tried searching at all? What BIOS version u using? I'd recommend flashing the latest.
Quote from: gerasimatos on 15-November-05, 04:32:02
Hello,
I recently built a system for my friend and he wanted the following setup. Everything works good, but when he selects Windows to shutdown, the OS goes through regular procedures, then the screen fades to black. However, the fans keep running and the PSU is still live..... so it seems the system isnt shutting down 100%. I have seen this issue before, but dont remember how to fix it. Something to do with the registry or within the system, alas, i cannot remember. please assist.
K8N NEO4 Platinum SLI Mobo
AMD 3500+ Venice Core processor 939 chipset
Antec TruePower PSU 480W
2 x 512 Corsair PC3200 RAM
Antec case
2 x Evga 6800gt ultra video cards
2 x Hitachi 80GB Sata II drives in a Raid 0
1 x NEC DVD/R/RW drives
Windows XP Pro OS

K8N Neo4 Platinum - 20 Pin PS Compatible?

Hello,
I was considering an upgrade, which would include a K8N Neo4 Platinum motherboard, with an A64 3200 Venice, X850XT, and 1GB RAM.
My current power supply is a 480W Antec model, with a 20-pin ATX connector. I know some motherboards with a 24-pin socket are backwards compatible to work with 20-pin power supplies, the extra 4 pins are just left empty. Is this the case with the K8N Neo4 Platinum, or will it only work with the 24-pin power supplies?
Thanks!

I run 380W ANTEC 20pin with all the item in my SIG up to 2550 Mhz. The X850XT mite use a lot of juice but if your using an ANTEC True Power 480 Its got 28A on a single 12v rail. Or is it a different 480? Most here would say 24-28A 12V is good for a 64bit system and or in SLI config.
Most 24+4 pin MOBO will work with 20+4 pin as long as its a good PSU. So far I only know of DFI-SLI boards that need 24+4 pin to run.
Quote
K8N Neo4 Platinum motherboard, with an A64 3200 Venice, X850XT, and 1GB RAM
<------------ nice budget gaming rig. 3200+ Venice will easly OC to 2400Mhz on stock Vcore and runs very cool. Upto 2700Mhz on air cooling, 2900Mhz on water. I take it your using non SLI version of NEO 4, 7125 ? Great MOBO just the lack of SLI, only useful if running X2-Geforce cards. X850XT one of the best single cards out there, for me I've always used Geforce. 1GB is the sweet spot, only running more apps needs more RAM. Make sure that if its 2X512 match pair they work with this board. Some people here have problems running 4X512 @ 400Mhz+ 2X512 should be fine. Just do a search in this forum and also check out the MSI test report
Good luck

MSI K8N Neo4 Platinum SLI sound needs -5V; newest Antec 550W has no -5V rail

I came within a whisker of ordering a non-returnable 3700 Venice, MSI K8N Neo4 Platinum SLI mobo and an upgraded Power Supply, Antec's newest 550W PS the TP2-550 EPS12V ($117). This has dual 2x24pin 12V 19A rails and is touted as the new V2.0 EPS12V/ATX12v compatible power supply for high performance SLI systems. By accident I came across a page at MSI for this mobo
http://www.msi.com.tw/program/products/mai...ail.php?UID=641
At the end is this warning: MSI Reminds You...
• For this model, you must use a Power Supply which has a -5V pin supply. Also, the users manual which I downloaded on Pg 2-10 says the same thing
The above Antec PS specs do not show a -5V rail, nor does an Enermax 600W I looked at. The V2.0 specs for ATX12v which added 2x24pin 12V rails dropped -5V rail from the spec and it appears MSI is not conforming to the spec (See Antec response at end) None of the web sites selling these PS & mobos contain any warning. I vaguely recall from a forum a while back it may have something to do with the Soundblaster system in the mobo.
http://www.antec.com/us/productDetails.php?ProdID=22551 (click specifications)
Isn't this a major showstopper which is going to cause a lot of grief for those of us upgrading to SLI systems using this mobo and upgrading our PS to the newest & best power design? We won't know the PS won't work until we build the system.
Regards, Ron
Antec reply to me:
>>>>Thanks for the link. Since MSI's website does state the motherboard needs the -5v, the True550EPS12V will not work with this motherboard. The Standard (http://enhanceusa.com/documents/atx12v_v2.01.pdf) has removed the use for the -5v rail and it is no longer needed. MSI has not manufactured that motherboard to the Standard. Finding an ATX12V v2.0 power supply with the -5v might be hard to find. You should contact MSI for a compatibility list of power supplys that were tested to work with the K8N SLI Platinum.

Quote from: ccve3 on 21-May-05, 07:27:40
Wow!! syar2003 thanks for that post. I've spend an hour going through it & fasteddies links. Now I are a power expert. The dual rail argument is enough for me to go back to the MSI K8N Neo4 Platinum SLI with one of the single rail PS -5V units listed by fasteddie. The only question left now refers to computerpro3 recommendation on ultra power supplies for SLI
>>I quite simply wouldn't dream of putting anything else in my machine. Keep in mind, this section is for 2x 6800 models, not the 6600's which most any good psu will handle (like Antec Neopower, ocz 520, etc). . Pc Power and Cooling 510 Deluxe SLI edition (refer to list)
2. Zippy/Emacs 550-700w models
3. OCZ 600w (personally I would get the pcp&c for the price, but it's been proven here, so I'll be fair...).
These are really high end, expensive and only 3-4 choices. Since I'm getting one 6800GT and eventually another & possibly eventually a 4800 X2, I was hoping the OCZ 520W would do it but computerpro3 says Powermaster 520 isn't good enough for SLI. I found that there is an OCZ 600W ATX12 dual rail which surprisingly has a -5V rail needed for K8N Neo4 SLI Soundblaster. Will this meet computerpro3's preference for a high end PS for SLI systems even though I'm losing the 1 rail advantage. Maybe the 600 Watts just overwhelms the 1 rail/2 rail question.
Thanks again for the teriffic help
Regards, Ron
Wondering what you settled on. I got the Antec TP550 and it's flawless on the board. I even have the older 20pin model which works perfectly (including sound). If you really wanted what I would consider to be a top dog (pcpower and cooling), and find the -5v rail missing, all you have to do is place a phone order and request they add a -5v rail. It's a minimal cost and a total solution for having everything. Just my $0.02

K8N Neo4 Platinum (PCB 1.0) and AMD 64 3800+ X2

Help!
I have a K8N Neo4 Platinum (PCB 1.0) and it had an AMD 64 3200+ single core CPU.
Now I've upgraded to an AMD 64 3800+ X2 dual core but the BIOS and MS Vista are seeing only the one core.
The BIOS is at the latest version - 1.D.
Whats' going on?
Hitch.

Quote from: hitchhiker on 20-April-07, 08:44:57
This motherboard does support the X2 CPU right?
It's listed as supported on the MSI website but has nayone else got both cores running on it?
Hitch.
Yes it does support X2
Did you clear cmos with power cable disconnected from psu?
Look at my signature for link to proper method.

Thermaltake Silent Purepower 480W for K8N NEO4 Platinum

Similar Messages

Maybe you are looking for