Thinkcentre m93 tiny does not turn on and power indicator led is always red.

Any ideas ? Thanks.

Faulty AC adapter? Bad motherboard?
Disclaimer: While I do work for Lenovo Partner, all my contributions are my personal, non-official and not that of Lenovo or my employer.

Similar Messages

  • HT1267 what if your iphone 4 does not turn on and you dont have any way to get the Serial number what do u do

    what if your iphone 4 does not turn on and u have no way to get the serial number what do u do

    If you eject the SIM card tray the serial number is also there.  It's tiny, but there.
    When my iPhone won't turn on I first charge it with a known good cable for a few hours.  If nothing after that I begin a warranty lookup for repair.

  • My iPod does not turn on and it is not recognized by my laptop in iTunes... What can I do?

    My iPod does not turn on and it is not recognized by my laptop in iTunes... What can I do?
    Model iPod 2 Touch, 8G, It stoped working less than a month after it was purchased but I never sent it back for repairs or warranty to Apple.. Is there still a way to repair it on my own. It just simply does not turn on or charge and it is not recognized by iTunes when I plug it in to my MacBook Pro.
    Please advise...

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer                 
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. The appointment is free.
    Apple Retail Store - Genius Bar              

  • TS2771 My ipod touch gen 2 does not turn on and will not let me charge it.

    My ipod touch gen 2 does not turn on and will not let me charge it.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar

  • My ipod nano 7th gen does not turn on and is not recognized by my pc

    Don't know why my ipod does not turn on anymore. I only had it for 2 weeks. It also is not recognized on my pc or itunes when I plug it in with my USB.

    How long have you left the iPod to charge?  It can take up to 30 minutes for the iPod to power on or show any signs of life.  How long did you press and hold the Select (Center) and Menu buttons to reset the iPod?
    It might not to also make use of another USB sync cable if you have one laying around to rule out the possibility of a faulty/damaged cable.
    B-rock

  • Ipod touch 5th gen does not turn on and i only get an empty battery with thunderbolt at the bottom when i try to recharge it

    ipod touch does not turn onand i get empty batterywith small thunderbolt at the bottom wen i try to charge it

    - See:      
    iPod touch: Hardware troubleshooting
    - Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar      

  • Ipod does not turn on and is not recognized in Itunes and computer

    For some reason, one day, my ipod nano 4th generation just stopped working. On the device manager, I can see that the apple mobile USB driver is installed but it is not listed as an external hard drive on my computer. When I plug my ipod in, I have to push the top and the middle button together until it makes the sound when the computer recognizes a new USB. Then, it keeps saying 'waiting for ipod' and I eventually get a 1601 error message. I've tried everything, and it doesn't work at all. do you guys know how to fix this? This is just making me angry and furious.

    I have the same problem as from this morning my ipod nano just won't turn on and when I plug into computer its recognising an external hard drive but NOT syncing with itunes....Its just gone completely dead!!! Can anyone help?

  • IMac G5 does not turn on after power cord knocked off

    I have an iMac G5 that I recently passed on to my daughter. For the past few years it has been working fine except for one occasion that I replaced the power supply. At that time it was still covered by warranty and Apple sent me a replacement unit that I installed myself. Lately, the power cord was knocked off while the computer was on and now it will not turn on completely. It starts for about 15 seconds up to the gray Apple logo then the screen goes blank. I monitored the LEDs and all 3 do turn on then the computer shuts down. At first I thought it's the power supply that was affected with the power cord accident, and bought a replacement unit. I have just installed it but still the same problem exist. I am now asking for help from the expert souls out there to save this computer. Thanks.

    No more ideas except to try starting from the install disc and see if that works. Resetting the PRAM might jolt it back to life, it's worth a try, but I am not hopeful.
    If you do take it in, please let us know whether it was the logic board...

  • Engineer does not turn up and lies about it.

    I called BT at 4:42. Operator told me an engineer would come before 6pm. I asked if the engineer was definitely coming, the operator replied that yes, he definitely was coming by 6:00.
    At 5:58, the engineer had still not arrived, so I phoned again. I stated that no engineer had arrived. I was then put on hold while the order was checked. When the operator came back on the line, I was transferred to the Infinity Team.
    The Infinity Team operator introduced himself then put me on hold while he checked what was happening to the order.
    At 6:14 he came back told me he was checking with the engineer and put me back on hold.
    At 6:18, the operator asked me whether I was calling from the landline or mobile. I replied landline and he said he would call me back. As I had not heard anything from anyone at BT despite there being a problem, I asked to remain on hold while he sorted out what was going on. I had little confidence in receiving a call back.
    At 6:38 I was told the operator was speaking to engineers.
    At 6:44 the line went dead.
    At 6:45 the operator called back, apologised and told me he was speaking to the engineers. I was put on hold again.
    At 6:59 the operator said the engineer called at 1:30 pm and waited half an hour. I was then asked the colour of my door. It is glass and white – was then told that is what the engineer said. I asked what floor did he call at?
    At 7:12, the line went dead. The operator did not call back.
    I live in a small maisonette – it is impossible for the engineer knocking not to be heard. Totally impossible. The engineer is lying. BT and the engineer have both my mobile and home number. No calling card was left and no one called and no one knocked the door. Furthermore, no one mentioned a failed engineer visit during my first call when I was still being assured the engineer was on his way.
    It is poor enough, an engineer just not showing up, but the subsequent lie and just getting cut off is unacceptable.

    OMG the same thing has just happened to me. 
    I was assigned a slot from 8am to 1pm for an engineer to arrive.  At 13:20pm when noone had arrived I called BT.  I was transferred on the call a number of times having to go through the whole story with several people and was then cut off.  I had to call a number of times before I was able to get through to someone who could help.  I was then kept on hold for a very long time while the person contacted the engineering department.
    I was told that if I waited for a further hour someone would be with me.  At about 2:30pm I then called BT again when noone had turned up.  I made the call from my home office and was looking out on the street infront of my house while i was on the phone.  I was on the phone with BT till after 3pm and never once did I see any BT vehicle or engineer on the street.  I was then told that the engineer had visited my home at 2:30pm and had tried to contact me on my mobile but noone was in!  So as it turns out I was on the phone to BT from my personal landline number looking out onto my front door at the same time as the engineer had visited and determined that I was not in!!!  I cannot believe it!  I actually will have proof of this from my phone records as well!  The engineer apparently also rang my mobile which was on my desk next to me while I was on the landline with BT!! 
    I must say that being treated like this has left me with very little trust in BT - and this is before I even have the phone installed!!!  I now have to wait to the 29th Jul for this all to happen again!!!

  • HT201263 ipod charger exploded and the itouch does not turn on and is not recognized by windows or itunes

    connected the charger and after about 5 seconds the charger exploded with a bang and you could smell burnt circuits and the screen went black and hasn't started since then..

    When all of the magic blue smoke comes out your device is toast, and unless your device is still under warranty there isn't much you can do except buy another iPod.
    BTW:  If you were using an Apple brand charger and the failure was not due to an electrical storm or a problem with the house wireing, you may be covered.....

  • Nature space app sound does not turn off and why is the camera living underneath the app screen

    Cannot get the sound on the nature space app to turn off. And wondering if the app normally uses the camera. As I'm new to this it could be simple? Or is it a bug? The camera is sitting under the screen which isn't t making sense to me!!

    Never mind. Apparently a duplicate of other threads. Possible fix: update the defective OSX Lion to Mountain Lion.

  • My imac does not turn al the way on the sreen is blank and it beeps

    can some one help with my problem with my imac it does not turn on and only beeps

    This indicates  problem with RAM.
    You have to take the computer to the Apple store to have it checked out.
    http://support.apple.com/kb/HT5860?viewlocale=en_US
    Best.

  • When I connect my iphone 5 to charge, repeated again and again the charge sound, but does not turn! HELP!!

    help with iphone, you may not start and repeat the sound over and over again that the screen is broken?

    Hello obrunaga,
    Thank you for providing the details of the issue you are experiencing with your iPhone.
    I recommend following steps 2-6 below for an issue like the one you described:
    If a single application is not responding or stops responding when it opens, you can force it to close.
    If the device is unresponsive or if certain controls aren't working as expected, restart your device.
    If the device remains unresponsive or does not turn on (or power on),reset your device.
    If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
    If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
    Let charge for at least twenty minutes, then see if it starts normally.
    If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
    If the screen displays a red battery icon, continue charging the device until the battery is fully charged.
    If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
    Connect the device to your computer and open iTunes.
    If the device appears in iTunes, select and click Restore on the Summary pane. Learn more about restoring iOS software.
    If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
    If the above steps do not resolve the issue, contact Apple.
    You can find the full article here:
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    If you get to step 5, I recommend backing up your iPhone before performing the restore:
    iOS: Back up and restore your iOS device with iCloud or iTunes
    http://support.apple.com/kb/HT1766
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • Imac does not turn off.

    hello,
    I have an imac, running on os x lion. u know how, when you click on shutdown, it shows the white screen. sometimes my imac does not turn off and keep showing it. could you please tell me what i can do to solve this problem.
    thanks

    The safe boot more or less resets system files.
    When it is something in the hardware:
    1.do the Pram and the SMC resets:
    http://support.apple.com/kb/ht1379
    http://support.apple.com/kb/HT3964
    2. shutdown the mac and startup while holding the ALT(option) key: choose the Recovery Disk, from the window choose Disk Utility, select the Lion disk, choose "repair disk".
    When it is not a hardware problem:
    3. List the applications you installed in the last 6 months, also the ones from the Appstore.
    4. List the plugins (extensions) you have in Safari.

  • My blackberry z30 does not turn on with red light flashing

    hi i have a blackberry z30 , after charging my blackberry z30 it does not turn on and show me a red light blinking 5 times...what i should do? please help. 

    Hi and Welcome to the Community!
    Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):Connect your BB to the wall chargerLeave it alone for 2 hours, no matter what the LED or the display doesHold the up/down volume keys until the device is fully powered offWait 15 minutesPower up normallyWait another 2 hours, no matter what the LED or the display doesThis has been known to "kick start" some BBs. If it fails, then please try again but increase the step 4 wait time to 2 hours, and perhaps as long as 4-5 hours. If it fails to help, then your next step is in-person evaluation by a qualified technician. If you remain in warranty, seek support under those terms. If you have no warranty, then seek out a local (to you) shop with a qualified technician and have them provide you with a proper evaluation and estimate.
    Good luck and let us know!

Maybe you are looking for

  • Proximity Sensor locks touch screen

    Hello, I got a Z1C, the screen broke and I replaced it with a new funcioning one, but the problem is that whenever the proximity sensor notices that something (ear, hand, pocket) is closing in on it it does its function of locking the touch screen bu

  • Grouping objects by drawing round them

    I am using the latest Pages (5.1) and I do a lot of grouping of graphics objects. However, the only way I know to do it is to select every object individually (holding the command key). Is there any way to draw round part of the screen to define an a

  • Enabling multiple BAdi Calls

    Hello there, i'm relatively new to ABAP and SAP R/3. I use SAP CRM 5.0, and implemented an address check for the transaction BP (for creation of business partners) via the BAdi "address_check". Now I'd like to know why a BAdi is only called once afte

  • Pages Video Tutorials: how do I find them?

    I don't seem to be able to find tutorials for Pages (or for Keynote, which I know exists). Not sure why this is so hard to find!!

  • Grey screen fix ??

    I'm trying to fix the Grey screen issue on my Mac book pro.  I have started it up using command"R".  I tried reinstalling Mac OSX but there is not enough space required.  There is only 49.4 mb available. I then went into disk utility and started veri