Thinkpad a22m 2628 no sound

My Thinkpad a22m 2628 is running Windows 2000 SP4 and the drivers for the sound are installed acording to the computer and it seems to be utilizing the resources correctly. I have turned on the spekers themselves and they work fine under linux I know that it is a combo driver (CS4624/CS4297A) and I have installed to the letter of the drivers from the Lenovo website but still no sound with the speakers or headphone jacks any help would be appreciated.
Thank you in advance

Hello,
if you run the downloaded audio-package, it only will be extracted to C:\DRIVERS\W2K\Audio (or similar). You additionally have to execute the CRYSETUP.exe from there.
Please also read the "Readme" from download page for additional requirements to get sound.
My home-forum: http://www.thinkpad-forum.de
Wiki: Deutsches ThinkPad-Wiki English ThinkWiki
My ThinkPad-Collection

Similar Messages

  • Hard Drive Upgrade on a Thinkpad A20m 2628-11U

    I've got a Thinkpad A20m 2628-11U that has an IBM Travelstar 10gig Drive in it.  After using the laptop for about half an hour, the drive warms up and gets to the point of someone using a hammer and chisel to store data.  So I decided to purchase a WD250BEVE (PATA) drive to replace it.  Right off the bat, The laptop would not recognize the drive at all.  I've tried updating the bios and such to no avail.  I've even RMA'd the drive with western digital questioning them along the way as to the possibility of why their drive would not work in this unit.  They show no record of complaint.  When the new drive showed up, I got the same results.  Can anybody tell me if IBM put a drive or Brand limit on this unit or have any idea why a WD would not be recognized at all?
    Thanks for your time...
    Gary

    Welcome to the forum!
    Have you properly inserted the drive, because that's the reason for drive not being "seen" by the machine 90% of the time, and that can be tricky on A2x and A3x unit...make sure it's sitting properly in its caddy and is pushed in all the way.
    Even if your machine had a BIOS limit (137GB for older ThinkPads) the drive would still be recognized. There are no "brand restrictions" on ThinkPads of this generation.
    Hope this helps.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • Ethernet Capability in ThinkPad A21m [2628]

    My ThinkPad A21m [2628] does not currently have Ethernet capability.  (“Network card” was an optional extra at the time of purchase in 2001.)  The Ethernet port on the rear of the ThinkPad A21m is covered over with a cover that looks like it could be pried off.  It is hard to see whether there is an actual Ethernet port underneath the cover. 
    I am wondering whether I would be able to add Ethernet capability to this computer.  Can I simply pry off the cover, buy a compatible network card, put it into the computer myself according to the hardware manual, and then install the driver?  Or, does the fact that the Ethernet port is covered over mean that there is nothing I can do about it now?  My operating system is Windows 2000 SP4.  I would appreciate any advice on this issue. Thank you.
    Solved!
    Go to Solution.

    Yes.
    Just replace the modem card with an appropriate LAN/modem combo card and it will work "out of the box".
    You might have to download the appropriate driver, but the procedure is as simple as stated above, I've performed this myself many a times in the old days on both A2x and T2x units.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • Wireless Card IBM to laptop A22m - 2628

    Can anyone advice about the FRU number on the ref card in the subject. Thx, Kenneth

    Ron_9972 wrote:
    Hi kstrid,
    The FRU number for the wireless card is 06P3809.  The A22 System FRU Parts List is here:
    http://support.lenovo.com/en_US/detail.page?LegacyDocID=MIGR-38952&velxr-layout=print
    All part FRUs are listed in the Hardware Maintenance Manual:
    http://download.lenovo.com/ibmdl/pub/pc/pccbbs/bp_thinkpad/06p8883.pdf
    That is not the correct FRU for the card in question.
    Unlike other ThinkPads, A22m had an integrated wireless card in one of the PCMCIA slots - not in the mini PCI slot - and the FRU was 26P8087
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • Thinkpad Yoga: Strange honking sounds and audio/video glitches

    WARNING: LOUD VIDEO EXAMPLES
    I have a Thinkpad Yoga, type 20CD with Windows 8.1, and when I'm running some white noise to help me concentrate, I get these strange honking noises that are quite disruptive. Even worse is that when I'm trying to watch a video on youtube, the honking noise occurs and this seems to lead to quick stalls in the video as well (note: the major stall in the middle of this video may just have been a bit of lag, I meant to highlight the minor stalls like the one that occurs at around 2 seconds). Actually, it seems that the honking causes the entire system's video to stall (e.g. cursor stalls, clock stalls, etc)
    I've found only one other thread dealing with this issue and it wasn't resolved.
    Addressing the suggestions brought up in the linked thread:
    1) The problem occurs regardless of if I'm using the laptop's built-in speakers or my headphones. I don't see any reason to hook it up to my TV and check HDMI out.
    2) Yes, problem persists with headphones.
    3) The problem occurs whether I'm using the lowest quality or the highest quality audio.
    4) It's the whole system, not just one application.
    5) The microphone has nothing to do with it. Enabled or disabled, the problem still persists.
    I've updated my audio drivers but this hasn't done anything to mitigate the problem.
    Strangely enough, what does help is turning off my WiFi (i.e. Fn + F8). When the honking is occuring, I can switch the wireless card to airplane mode and the problem immediately goes away. I've read somewhere that this may be because of poor grounding on the audio card, meaning that the antenna is possibly picking up radio signals.
    Are there any possible solutions to this problem? 

    cesario85 wrote:
    OK The sticky label says SB0240
    Here's the screenshot:
    [img"]http://www.strikeforceguild.com/temp-images/IRQs.gif" width="640" height="45[/img]
    I have since tried putting in a different sound card (another soundblaster, I think a 28 model) and installed its drivers but had the same problems. Im having a go at using the onboard sound though, just to see.Message Edited by cesario85 on 09--2005 06:57 PM
    Audigy shares IRQ with IDE controller and firewire controller. This is not good.
    NOTE: I suppose you're running your PC on "Standard PC" -mode (since IRQ's >5 not showing). If so, you can try to assign IRQ for the PCI slot, Audigy is installed, manually from BIOS. See your motherboard manual page 4-26.
    Can you check if your PC is running as "Standard PC" and not as "ACPI Uniprocessor PC" (Device Manager --> Computer). Make it "ACPI Uniprocessor PC" --> you get more IRQs (virtual) in use.
    NOTE: You may need to reinstall OS to get this done.
    Also you may need to enable APIC mode on BIOS.
    How To:
    A) Go to 'Device Manager' a short cut to get there is "Right Click" on the My computer Icon on your desktop (Control Panel --> System --> Hardware),
    B) Next click on 'Computer', then double click on 'Standard PC'. Then select 'Driver' and then 'Update Driver'.
    C) At this point you will see a screen pop up asking you to do this "Automatically" or Select 'Display a list of the known drivers for this device', - Choose this option.
    D) Next you will see - 'Show all hardware of this device class'. Now you can select "ACPI Uniprocessor PC" in the list shown in the window to the right.
    E) Now Windows needs/will re-start and re-install all hardware/ settings needed to run in this configuration.
    .jtpMessage Edited by jutapa on 09--2005 0:23 PM

  • Thinkpad T500 suddenly no sound since yesterday~!

    I bought this Thinkpad T500 two months ago, every thing works fine but yesterday my laptop suddenly have NO sound, neither the headphone, i checked the sound device and i think it's fine and i scanned my pc there is no virus exist, so please help me with that lol (P.S. I think it was happened after i wake up my pc from stand by and my operating system is Vista Business)

    I recommend trying what this user did to fix his/her issue... http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/T500-no-sound-from-internal-speaker-but-Hea...
    IT Specialist and Consultant
    Lenovo Tablet Evangelist
    Current Machines: IdeaCentre A300, ThinkPad Tablet, IdeaPad U410, and Yoga 3 Pro Touch
    Deutsche Community   Comunidad en Español
    Lenovo - the latest in DOtabs, DOpads, DOcentre's, DOstations and DOservers!

  • Thinkpad T60 fans making sound

    Hello all,
    I had this thinkpad t60 for 10 months now, lately I noticed there's an noise coming from the fans located on the left side of the laptop when the systems heat up at 92º F.  The noise last about a few seconds during the warming up stage, then its quite like normal, it's repeats a few times during the laptop is ON.
    I don't know if anyone has the same problem, I'm thinking of something might get stuck blocking the fans or the oil is dried out.
    Any help would be appreciate.
    Thanks.
    TWS

    Yes, calling for support would be the best thing since it's under warranty.
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество
    Jane
    2015 X1 Carbon, ThinkPad Slate, T410s, X301, X200 Tablet, T60p, HP TouchPad, iPad Air 2, iPhone 5S, IdeaTab A2107A, Yoga Tablet, Yoga 3 Pro
    I am not a Lenovo Employee.
    I AM one of those crazy ThinkPad zealots!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!

  • PCI slot in Thinkpad Dock II unusable

    Hello, I have a Thinkpad a22m 2628-S1U which can be used with the Thinkpad Dock II. To avoid feeling tempted to buy a new laptop I bought that dock as well as an ATI Radeon x1550 to put in its PCI slot. These items were said to be compatible on http://thinkwiki.org the Linux thinkpad wiki.
    Now that I've tried it out, I'm starting to think the contributors to that site were windows users who didn't read the topic. Starting up docked gave the following lspci output (notice there's no radeon card):
    00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
    00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
    00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03)
    00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03)
    00:03.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 09)
    00:03.1 Serial controller: Xircom Mini-PCI V.90 56k Modem
    00:04.0 PCI bridge: Texas Instruments PCI2032 PCI Docking Bridge
    00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24/30 [CrystalClear SoundFusion Audio Accelerator] (rev 01)
    00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
    00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
    00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
    00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03)
    01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility M3 AGP 2x (rev 02)
    08:01.0 IDE interface: Silicon Image, Inc. PCI0648 (rev 01)
    08:02.0 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
    08:02.1 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
    0f:00.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01)
    For comparison, here's what my lspci looks like undocked:
    00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
    00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
    00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03)
    00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03)
    00:03.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 09)
    00:03.1 Serial controller: Xircom Mini-PCI V.90 56k Modem
    00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24/30 [CrystalClear SoundFusion Audio Accelerator] (rev 01)
    00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
    00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
    00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
    00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03)
    01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility M3 AGP 2x (rev 02)
    02:00.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01)
    So a few parts of the dock are getting detected but not the most important parts. The error that I think is related to the absence of the graphics card appears in dmesg. Look for the part about "cannot allocate resource region":
    Linux version 2.6.26-ARCH (root@T-POWA-LX) (gcc version 4.3.2 (GCC) ) #1 SMP PREEMPT Tue Sep 9 10:15:21 UTC 2008
    PAT disabled. Not yet verified on this CPU type.
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    BIOS-e820: 000000001fff0000 - 000000001fffec00 (ACPI data)
    BIOS-e820: 000000001fffec00 - 0000000020000000 (ACPI NVS)
    BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    0MB HIGHMEM available.
    511MB LOWMEM available.
    Entering add_active_range(0, 0, 131056) 0 entries of 256 used
    Zone PFN ranges:
    DMA 0 -> 4096
    Normal 4096 -> 131056
    HighMem 131056 -> 131056
    Movable zone start PFN for each node
    early_node_map[1] active PFN ranges
    0: 0 -> 131056
    On node 0 totalpages: 131056
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 4064 pages, LIFO batch:0
    Normal zone: 992 pages used for memmap
    Normal zone: 125968 pages, LIFO batch:31
    HighMem zone: 0 pages used for memmap
    Movable zone: 0 pages used for memmap
    DMI 2.3 present.
    ACPI: RSDP 000F7160, 0014 (r0 PTLTD )
    ACPI: RSDT 1FFF53D5, 002C (r1 PTLTD RSDT 6040000 LTP 0)
    ACPI: FACP 1FFFEB65, 0074 (r1 IBM TP-13 6040000 0)
    ACPI: DSDT 1FFF5401, 9764 (r1 IBM TP-13 6040000 MSFT 100000C)
    ACPI: FACS 1FFFF000, 0040
    ACPI: BOOT 1FFFEBD9, 0027 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
    ACPI: PM-Timer IO Port: 0x1008
    Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000)
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
    SMP: Allowing 0 CPUs, 0 hotplug CPUs
    PERCPU: Allocating 39464 bytes of per cpu data
    NR_CPUS: 16, nr_cpu_ids: 1
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130032
    Kernel command line: BOOT_IMAGE=arch ro root=802 hpet=force pci=routeirq acpi_osi=Linux panic=10
    ACPI: Added _OSI(Linux)
    Local APIC disabled by BIOS -- you can enable it with "lapic"
    mapped APIC to ffffb000 (0140e000)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 2048 (order: 11, 8192 bytes)
    Detected 697.417 MHz processor.
    Console: colour VGA+ 80x25
    console [tty0] enabled
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Memory: 514452k/524224k available (2120k kernel code, 9264k reserved, 744k data, 264k init, 0k highmem)
    virtual kernel memory layout:
    fixmap : 0xffee4000 - 0xfffff000 (1132 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
    lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
    .init : 0xc03d3000 - 0xc0415000 ( 264 kB)
    .data : 0xc031225e - 0xc03cc380 ( 744 kB)
    .text : 0xc0100000 - 0xc031225e (2120 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    CPA: page pool initialized 1 of 1 pages preallocated
    SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    Calibrating delay using timer specific routine.. 973.82 BogoMIPS (lpj=1622127)
    Security Framework initialized
    Capability LSM initialized
    Mount-cache hash table entries: 512
    CPU: L1 I cache: 16K, L1 D cache: 16K
    CPU: L2 cache: 256K
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    Freeing SMP alternatives: 9k freed
    ACPI: Core revision 20080321
    ACPI: Checking initramfs for custom DSDT
    ACPI: setting ELCR to 0200 (from 0e80)
    weird, boot CPU (#0) not listedby the BIOS.
    SMP motherboard not detected.
    Local APIC not detected. Using dummy APIC emulation.
    SMP disabled
    Brought up 1 CPUs
    Total of 1 processors activated (973.82 BogoMIPS).
    net_namespace: 652 bytes
    Booting paravirtualized kernel on bare hardware
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=14
    PCI: Using configuration type 1 for base access
    Setting up standard PCI resources
    ACPI: EC: Look up EC in DSDT
    ACPI: EC: non-query interrupt received, switching to interrupt mode
    ACPI: Interpreter enabled
    ACPI: (supports S0 S1 S3 S4 S5)
    ACPI: Using PIC for interrupt routing
    ACPI: EC: GPE = 0x9, I/O: command/status = 0x66, data = 0x62
    ACPI: EC: driver started in interrupt mode
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    pci 0000:00:07.3: quirk: region 1000-103f claimed by PIIX4 ACPI
    pci 0000:00:07.3: quirk: region 1040-104f claimed by PIIX4 SMB
    pci 0000:00:07.3: PIIX4 devres C PIO at 15e8-15ef
    pci 0000:00:07.3: PIIX4 devres I PIO at 03f0-03f7
    pci 0000:00:07.3: PIIX4 devres J PIO at 002e-002f
    PCI: Transparent bridge - 0000:00:04.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.DOCK._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 9 10 11)
    ACPI: Power Resource [PSER] (off)
    ACPI: Power Resource [PSIO] (on)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp 00:00: mem resource (0x0-0x9ffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc0000-0xc3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc4000-0xc7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc8000-0xcbfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xcc000-0xcffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd0000-0xd3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd4000-0xd3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd8000-0xd7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xdc000-0xdbfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe0000-0xe3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe4000-0xe7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe8000-0xebfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xec000-0xeffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xf0000-0xfffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0x0-0x9ffff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc0000-0xc3fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc4000-0xc7fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc8000-0xcbfff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xcc000-0xcffff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd0000-0xd3fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd4000-0xd3fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd8000-0xd7fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xdc000-0xdbfff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe0000-0xe3fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe4000-0xe7fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe8000-0xebfff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xec000-0xeffff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xf0000-0xfffff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0x0-0x9ffff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc0000-0xc3fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc4000-0xc7fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc8000-0xcbfff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xcc000-0xcffff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd0000-0xd3fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd4000-0xd3fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd8000-0xd7fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xdc000-0xdbfff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe0000-0xe3fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe4000-0xe7fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe8000-0xebfff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xec000-0xeffff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xf0000-0xfffff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp: PnP ACPI: found 15 devices
    ACPI: ACPI bus type pnp unregistered
    PCI: Using ACPI for IRQ routing
    PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
    PCI: setting IRQ 9 as level-triggered
    ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
    PCI: setting IRQ 10 as level-triggered
    ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
    ACPI: PCI Interrupt 0000:00:03.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
    ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
    PCI: setting IRQ 7 as level-triggered
    ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 7 (level, low) -> IRQ 7
    ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt 0000:08:01.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt 0000:08:02.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
    ACPI: PCI Interrupt 0000:08:02.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
    PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
    PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0
    PCI: Cannot allocate resource region 9 of bridge 0000:00:04.0
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    ACPI: RTC can wake from S4
    system 00:00: iomem range 0x100000-0x1fffffff could not be reserved
    system 00:00: iomem range 0xfff80000-0xffffffff could not be reserved
    system 00:02: ioport range 0x1000-0x103f has been reserved
    system 00:02: ioport range 0x1040-0x104f has been reserved
    system 00:02: ioport range 0xfe00-0xfe0f has been reserved
    system 00:09: ioport range 0x15e0-0x15ef has been reserved
    PCI: region 0000:08:02.0/9 too large: 0x0000000000000000-0x0000000003ffffff
    PCI: region 0000:08:02.1/9 too large: 0x0000000000000000-0x0000000003ffffff
    PCI: region 0000:08:02.0/10 too large: 0x0000000000000000-0x0000000003ffffff
    PCI: region 0000:08:02.1/10 too large: 0x0000000000000000-0x0000000003ffffff
    PCI: Bridge: 0000:00:01.0
    IO window: 2000-2fff
    MEM window: 0xf0200000-0xf02fffff
    PREFETCH window: 0x00000000f8000000-0x00000000fbffffff
    PCI: Bus 15, cardbus bridge: 0000:00:02.0
    IO window: 0x00001400-0x000014ff
    IO window: 0x00001c00-0x00001cff
    PREFETCH window: 0x30000000-0x33ffffff
    MEM window: 0x34000000-0x37ffffff
    PCI: Bus 19, cardbus bridge: 0000:00:02.1
    IO window: 0x00003400-0x000034ff
    IO window: 0x00003800-0x000038ff
    PREFETCH window: 0x38000000-0x3bffffff
    MEM window: 0x3c000000-0x3fffffff
    PCI: Bus 9, cardbus bridge: 0000:08:02.0
    IO window: 0x00004000-0x000040ff
    IO window: 0x00004400-0x000044ff
    PCI: Bus 13, cardbus bridge: 0000:08:02.1
    IO window: 0x00004800-0x000048ff
    IO window: 0x00004c00-0x00004cff
    PCI: Bridge: 0000:00:04.0
    IO window: 4000-4fff
    MEM window: disabled.
    PREFETCH window: disabled.
    ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt 0000:08:02.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
    ACPI: PCI Interrupt 0000:08:02.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    TCP: Hash tables configured (established 16384 bind 16384)
    TCP reno registered
    NET: Registered protocol family 1
    Unpacking initramfs... done
    Freeing initrd memory: 662k freed
    Simple Boot Flag at 0x35 set to 0x1
    IBM machine detected. Enabling interrupts during APM calls.
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    apm: overridden by ACPI.
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    msgmni has been set to 1006
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:00:00.0: Limiting direct PCI/PCI transfers
    pci 0000:00:03.0: Firmware left e100 interrupts enabled; disabling
    pci 0000:01:00.0: Boot video device
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    serial 00:0c: activated
    00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    ACPI: PCI Interrupt 0000:00:03.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
    input: Macintosh mouse button emulation as /class/input/input0
    PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP cubic registered
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    registered taskstats version 1
    Freeing unused kernel memory: 264k freed
    input: AT Translated Set 2 keyboard as /class/input/input1
    ACPI: ACPI Dock Station Driver
    SCSI subsystem initialized
    libata version 3.00 loaded.
    ata_piix 0000:00:07.1: version 2.12
    scsi0 : ata_piix
    scsi1 : ata_piix
    Switched to high resolution mode on CPU 0
    ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x1850 irq 14
    ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1858 irq 15
    ata1.00: ATA-6: TOSHIBA MK1032GAX, AB211A, max UDMA/100
    ata1.00: 195371568 sectors, multi 16: LBA48
    ata1.00: configured for UDMA/33
    ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-T20L, NR02, max UDMA/33
    ata2.00: configured for UDMA/33
    scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1032GA AB21 PQ: 0 ANSI: 5
    scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20L NR02 PQ: 0 ANSI: 5
    ACPI: PCI Interrupt 0000:08:01.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI interrupt for device 0000:08:01.0 disabled
    Driver 'sd' needs updating - please use bus_type methods
    sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda:<4>Driver 'sr' needs updating - please use bus_type methods
    sda1 sda2 sda3 sda4
    sd 0:0:0:0: [sda] Attached SCSI disk
    sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 1:0:0:0: Attached scsi CD-ROM sr0
    ReiserFS: sda2: found reiserfs format "3.6" with standard journal
    ReiserFS: sda2: using ordered data mode
    ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: sda2: checking transaction log (sda2)
    ReiserFS: sda2: Using r5 hash to sort names
    rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month, y3k
    Non-volatile memory driver v1.2
    thinkpad_acpi: ThinkPad ACPI Extras v0.20
    thinkpad_acpi: http://ibm-acpi.sf.net/
    thinkpad_acpi: ThinkPad BIOS 13ET14WW (1.00c), EC unknown
    Registered led device: tpacpi::thinklight
    thinkpad_acpi: another device driver is already handling bay events
    thinkpad_acpi: disabling subdriver bay
    Registered led device: tpacpi::power
    Registered led device: tpacpi:orange:batt
    Registered led device: tpacpi:green:batt
    Registered led device: tpacpi::dock_active
    Registered led device: tpacpi::bay_active
    Registered led device: tpacpi::dock_batt
    Registered led device: tpacpi::unknown_led
    Registered led device: tpacpi::standby
    input: ThinkPad Extra Buttons as /class/input/input2
    e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
    e100: Copyright(c) 1999-2006 Intel Corporation
    ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
    e100: eth0: e100_probe: addr 0xf0120000, irq 10, MAC addr 00:03:47:0f:de:3d
    eepro100.c:v1.09j-t 9/29/99 Donald Becker
    eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others
    ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    gameport: CS46xx Gameport is pci0000:00:05.0/gameport0, speed 1807kHz
    Linux agpgart interface v0.103
    agpgart: Detected an Intel 440BX Chipset.
    agpgart: AGP aperture is 64M @ 0xf4000000
    [drm] Initialized drm 1.1.0 20060810
    ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    [drm] Initialized r128 2.5.0 20030725 on minor 0
    ath_hal: module license 'Proprietary' taints kernel.
    AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
    fuse init (API version 7.9)
    Marking TSC unstable due to: cpufreq changes.
    /proc/exmap: insert
    ACPI: AC Adapter [AC] (on-line)
    ACPI: Battery Slot [BAT0] (battery present)
    input: Power Button (FF) as /class/input/input3
    ACPI: Power Button (FF) [PWRF]
    input: Lid Switch as /class/input/input4
    ACPI: Lid Switch [LID]
    input: Sleep Button (CM) as /class/input/input5
    ACPI: Sleep Button (CM) [SLPB]
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    ACPI: ACPI0007:00 is registered as cooling_device0
    ACPI: Processor [CPU] (supports 8 throttling states)
    Clocksource tsc unstable (delta = 142862014 ns)
    ACPI: LNXTHERM:01 is registered as thermal_zone0
    ACPI: Thermal Zone [THM0] (49 C)
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sr 1:0:0:0: Attached scsi generic sg1 type 5
    Yenta: CardBus bridge found at 0000:00:02.0 [1014:0130]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:00:02.0, mfunc 0x00001000, devctl 0x66
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    Yenta: ISA IRQ mask 0x0038, PCI irq 11
    Socket status: 30000020
    Yenta: CardBus bridge found at 0000:00:02.1 [1014:0130]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:00:02.1, mfunc 0x00001000, devctl 0x66
    Yenta: ISA IRQ mask 0x0038, PCI irq 9
    Socket status: 30000006
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    Yenta: CardBus bridge found at 0000:08:02.0 [1014:0148]
    PCI: Bus 9, cardbus bridge: 0000:08:02.0
    IO window: 0x00004000-0x000040ff
    IO window: 0x00004400-0x000044ff
    PREFETCH window: 0x40400000-0x407fffff
    MEM window: 0x40800000-0x40bfffff
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:08:02.0, mfunc 0x00001002, devctl 0x66
    irq 11: nobody cared (try booting with the "irqpoll" option)
    Pid: 1799, comm: modprobe Tainted: P 2.6.26-ARCH #1
    [<c015a764>] __report_bad_irq+0x24/0x90
    [<c015aa52>] note_interrupt+0x282/0x2c0
    [<c0159e70>] handle_IRQ_event+0x30/0x60
    [<c015b2c3>] handle_level_irq+0xd3/0x100
    [<c010712b>] do_IRQ+0x3b/0x70
    [<c01049c7>] common_interrupt+0x23/0x28
    [<c0159e57>] handle_IRQ_event+0x17/0x60
    [<c015b26d>] handle_level_irq+0x7d/0x100
    [<c010712b>] do_IRQ+0x3b/0x70
    [<c01049c7>] common_interrupt+0x23/0x28
    [<c015007b>] show_initstate+0xb/0x50
    [<e0bd4830>] yenta_probe_cb_irq+0x80/0xf0 [yenta_socket]
    [<e0bd4bbb>] ti12xx_override+0x23b/0x6a0 [yenta_socket]
    [<c0210ce3>] pci_setup_cardbus+0x103/0x190
    [<e0bd5f02>] yenta_probe+0x5f2/0x643 [yenta_socket]
    [<c01cfa11>] sysfs_find_dirent+0x21/0x30
    [<c01d09c5>] sysfs_create_link+0x85/0x120
    [<c020b700>] pci_match_device+0xa0/0xc0
    [<c020b816>] pci_device_probe+0x56/0x80
    [<c026a9a6>] driver_probe_device+0x86/0x1a0
    [<c026ab31>] __driver_attach+0x71/0x80
    [<c020b760>] pci_device_remove+0x0/0x40
    [<c026a2d4>] bus_for_each_dev+0x44/0x70
    [<c020b760>] pci_device_remove+0x0/0x40
    [<c026a836>] driver_attach+0x16/0x20
    [<c026aac0>] __driver_attach+0x0/0x80
    [<c0269c67>] bus_add_driver+0x1a7/0x220
    [<c020b760>] pci_device_remove+0x0/0x40
    [<c026accc>] driver_register+0x5c/0x130
    [<c020ba4d>] __pci_register_driver+0x3d/0x80
    [<c0150738>] sys_init_module+0x148/0x1ca0
    [<c01a4bfa>] seq_open+0x3a/0x90
    [<c01c2aa6>] pde_users_dec+0x16/0x50
    [<e0bc9000>] hotplug_slot_attr_show+0x0/0x30 [pci_hotplug]
    [<c0268610>] device_remove_file+0x0/0x20
    [<c0103f73>] sysenter_past_esp+0x78/0xb1
    =======================
    handlers:
    [<e0a5f340>] (snd_cs46xx_interrupt+0x0/0x1e0 [snd_cs46xx])
    [<e0bd57e0>] (yenta_interrupt+0x0/0xe0 [yenta_socket])
    Disabling IRQ #11
    pccard: CardBus card inserted into slot 0
    ath_pci 0000:0f:00.0: enabling device (0000 -> 0002)
    ACPI: PCI Interrupt 0000:0f:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    input: PC Speaker as /class/input/input6
    USB Universal Host Controller Interface driver v3.0
    input: Video Bus as /class/input/input7
    ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
    IBM TrackPoint firmware: 0x0e, buttons: 3/3
    input: TPPS/2 IBM TrackPoint as /class/input/input8
    PPP generic driver version 2.4.2
    Uniform Multi-Platform E-IDE driver
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    parport_pc 00:0d: activated
    parport_pc 00:0d: reported by Plug and Play ACPI
    parport0: PC-style at 0x278, irq 5 [PCSPP,TRISTATE]
    MadWifi: ath_attach: Switching rfkill capability off.
    NET: Registered protocol family 23
    wifi0: Atheros AR2413 chip found (MAC 7.8, PHY 2112A 4.5, Radio 5.6)
    nsc-ircc 00:0e: activated
    nsc-ircc, chip->init
    nsc-ircc, Found chip at base=0x02e
    nsc-ircc, driver loaded (Dag Brattli)
    ath_pci: wifi0: Atheros 5212: mem=0x34000000, irq=11
    IrDA: Registered device irda0
    nsc-ircc, Found dongle: Reserved
    ppdev: user-space parallel port driver
    Yenta: ISA IRQ mask 0x0018, PCI irq 10
    Socket status: 30000006
    pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
    cs: IO port probe 0x4000-0x4fff: clean.
    Yenta: CardBus bridge found at 0000:08:02.1 [1014:0148]
    PCI: Bus 13, cardbus bridge: 0000:08:02.1
    IO window: 0x00004800-0x000048ff
    IO window: 0x00004c00-0x00004cff
    PREFETCH window: 0x40c00000-0x40ffffff
    MEM window: 0x41000000-0x413fffff
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:08:02.1, mfunc 0x00001002, devctl 0x66
    irq 11: nobody cared (try booting with the "irqpoll" option)
    Pid: 1799, comm: modprobe Tainted: P 2.6.26-ARCH #1
    [<c015a764>] __report_bad_irq+0x24/0x90
    [<c015aa52>] note_interrupt+0x282/0x2c0
    [<c0159e70>] handle_IRQ_event+0x30/0x60
    [<c015b2c3>] handle_level_irq+0xd3/0x100
    [<c010712b>] do_IRQ+0x3b/0x70
    [<c01049c7>] common_interrupt+0x23/0x28
    [<c014007b>] set_process_cpu_timer+0x2b/0xd0
    [<c0159e57>] handle_IRQ_event+0x17/0x60
    [<c015b26d>] handle_level_irq+0x7d/0x100
    [<c010712b>] do_IRQ+0x3b/0x70
    [<c01049c7>] common_interrupt+0x23/0x28
    [<c015007b>] show_initstate+0xb/0x50
    [<e0bd4830>] yenta_probe_cb_irq+0x80/0xf0 [yenta_socket]
    [<e0bd4aff>] ti12xx_override+0x17f/0x6a0 [yenta_socket]
    [<c0210ce3>] pci_setup_cardbus+0x103/0x190
    [<e0bd5f02>] yenta_probe+0x5f2/0x643 [yenta_socket]
    [<c01cfa11>] sysfs_find_dirent+0x21/0x30
    [<c01d09c5>] sysfs_create_link+0x85/0x120
    [<c020b700>] pci_match_device+0xa0/0xc0
    [<c020b816>] pci_device_probe+0x56/0x80
    [<c026a9a6>] driver_probe_device+0x86/0x1a0
    [<c026ab31>] __driver_attach+0x71/0x80
    [<c020b760>] pci_device_remove+0x0/0x40
    [<c026a2d4>] bus_for_each_dev+0x44/0x70
    [<c020b760>] pci_device_remove+0x0/0x40
    [<c026a836>] driver_attach+0x16/0x20
    [<c026aac0>] __driver_attach+0x0/0x80
    [<c0269c67>] bus_add_driver+0x1a7/0x220
    [<c020b760>] pci_device_remove+0x0/0x40
    [<c026accc>] driver_register+0x5c/0x130
    [<c020ba4d>] __pci_register_driver+0x3d/0x80
    [<c0150738>] sys_init_module+0x148/0x1ca0
    [<c01a4bfa>] seq_open+0x3a/0x90
    [<c01c2aa6>] pde_users_dec+0x16/0x50
    [<e0bc9000>] hotplug_slot_attr_show+0x0/0x30 [pci_hotplug]
    [<c0268610>] device_remove_file+0x0/0x20
    [<c0103f73>] sysenter_past_esp+0x78/0xb1
    =======================
    handlers:
    [<e0a5f340>] (snd_cs46xx_interrupt+0x0/0x1e0 [snd_cs46xx])
    [<e0bd57e0>] (yenta_interrupt+0x0/0xe0 [yenta_socket])
    [<e0ae4e30>] (ath_intr+0x0/0x4810 [ath_pci])
    Disabling IRQ #11
    Yenta: ISA IRQ mask 0x0018, PCI irq 10
    Socket status: 30000006
    pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
    cs: IO port probe 0x4000-0x4fff: clean.
    ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 7 (level, low) -> IRQ 7
    uhci_hcd 0000:00:07.2: UHCI Host Controller
    uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:07.2: irq 7, io base 0x00001860
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
    piix4_smbus 0000:00:07.3: IBM system detected; this module may corrupt your serial eeprom! Refusing to load module!
    piix4_smbus: probe of 0000:00:07.3 failed with error -1
    CMD648: IDE controller (0x1095:0x0648 rev 0x01) at PCI slot 0000:08:01.0
    ACPI: PCI Interrupt 0000:08:01.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
    CMD648: 100% native mode on irq 9
    ide0: BM-DMA at 0x3000-0x3007
    ide1: BM-DMA at 0x3008-0x300f
    Probing IDE interface ide0...
    usb 1-1: new full speed USB device using uhci_hcd and address 2
    usb 1-1: configuration #1 chosen from 1 choice
    hub 1-1:1.0: USB hub found
    hub 1-1:1.0: 4 ports detected
    Probing IDE interface ide1...
    usb 1-1.4: new low speed USB device using uhci_hcd and address 3
    usb 1-1.4: configuration #1 chosen from 1 choice
    ide0 at 0x3020-0x3027,0x3016 on irq 9
    ide1 at 0x3018-0x301f,0x3012 on irq 9
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    lp0: using parport0 (interrupt-driven).
    usbcore: registered new interface driver hiddev
    input: Logitech Logitech USB Optical Mouse as /class/input/input9
    input,hidraw0: USB HID v1.11 Mouse [Logitech Logitech USB Optical Mouse] on usb-0000:00:07.2-1.4
    usbcore: registered new interface driver usbhid
    usbhid: v2.6:USB HID core driver
    JFS: nTxBlock = 4027, nTxLock = 32219
    Adding 1100444k swap on /dev/sda4. Priority:-1 extents:1 across:1100444k
    warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
    conservative governor failed, too long transition latency of HW, fallback to performance governor
    thinkpad_acpi: requested hot key mask 0x0000ffff, forced to 0x00008000 (NVRAM poll mask is 0x00fb8000): no firmware mask support
    For comparison here is my dockless dmesg:
    Linux version 2.6.26-ARCH (root@T-POWA-LX) (gcc version 4.3.2 (GCC) ) #1 SMP PREEMPT Tue Sep 9 10:15:21 UTC 2008
    PAT disabled. Not yet verified on this CPU type.
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    BIOS-e820: 000000001fff0000 - 000000001fffec00 (ACPI data)
    BIOS-e820: 000000001fffec00 - 0000000020000000 (ACPI NVS)
    BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    0MB HIGHMEM available.
    511MB LOWMEM available.
    Entering add_active_range(0, 0, 131056) 0 entries of 256 used
    Zone PFN ranges:
    DMA 0 -> 4096
    Normal 4096 -> 131056
    HighMem 131056 -> 131056
    Movable zone start PFN for each node
    early_node_map[1] active PFN ranges
    0: 0 -> 131056
    On node 0 totalpages: 131056
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 4064 pages, LIFO batch:0
    Normal zone: 992 pages used for memmap
    Normal zone: 125968 pages, LIFO batch:31
    HighMem zone: 0 pages used for memmap
    Movable zone: 0 pages used for memmap
    DMI 2.3 present.
    ACPI: RSDP 000F7160, 0014 (r0 PTLTD )
    ACPI: RSDT 1FFF53D5, 002C (r1 PTLTD RSDT 6040000 LTP 0)
    ACPI: FACP 1FFFEB65, 0074 (r1 IBM TP-13 6040000 0)
    ACPI: DSDT 1FFF5401, 9764 (r1 IBM TP-13 6040000 MSFT 100000C)
    ACPI: FACS 1FFFF000, 0040
    ACPI: BOOT 1FFFEBD9, 0027 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
    ACPI: PM-Timer IO Port: 0x1008
    Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000)
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
    SMP: Allowing 0 CPUs, 0 hotplug CPUs
    PERCPU: Allocating 39464 bytes of per cpu data
    NR_CPUS: 16, nr_cpu_ids: 1
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130032
    Kernel command line: BOOT_IMAGE=arch ro root=802 hpet=force pci=routeirq acpi_osi=Linux panic=10
    ACPI: Added _OSI(Linux)
    Local APIC disabled by BIOS -- you can enable it with "lapic"
    mapped APIC to ffffb000 (0140e000)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 2048 (order: 11, 8192 bytes)
    Detected 697.425 MHz processor.
    Console: colour VGA+ 80x25
    console [tty0] enabled
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Memory: 514452k/524224k available (2120k kernel code, 9264k reserved, 744k data, 264k init, 0k highmem)
    virtual kernel memory layout:
    fixmap : 0xffee4000 - 0xfffff000 (1132 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
    lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
    .init : 0xc03d3000 - 0xc0415000 ( 264 kB)
    .data : 0xc031225e - 0xc03cc380 ( 744 kB)
    .text : 0xc0100000 - 0xc031225e (2120 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    CPA: page pool initialized 1 of 1 pages preallocated
    SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    Calibrating delay using timer specific routine.. 1396.15 BogoMIPS (lpj=2326640)
    Security Framework initialized
    Capability LSM initialized
    Mount-cache hash table entries: 512
    CPU: L1 I cache: 16K, L1 D cache: 16K
    CPU: L2 cache: 256K
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    Freeing SMP alternatives: 9k freed
    ACPI: Core revision 20080321
    ACPI: Checking initramfs for custom DSDT
    ACPI: setting ELCR to 0200 (from 0a20)
    weird, boot CPU (#0) not listedby the BIOS.
    SMP motherboard not detected.
    Local APIC not detected. Using dummy APIC emulation.
    SMP disabled
    Brought up 1 CPUs
    Total of 1 processors activated (1396.15 BogoMIPS).
    net_namespace: 652 bytes
    Booting paravirtualized kernel on bare hardware
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
    PCI: Using configuration type 1 for base access
    Setting up standard PCI resources
    ACPI: EC: Look up EC in DSDT
    ACPI: EC: non-query interrupt received, switching to interrupt mode
    ACPI: Interpreter enabled
    ACPI: (supports S0 S1 S3 S4 S5)
    ACPI: Using PIC for interrupt routing
    ACPI: EC: GPE = 0x9, I/O: command/status = 0x66, data = 0x62
    ACPI: EC: driver started in interrupt mode
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    pci 0000:00:07.3: quirk: region 1000-103f claimed by PIIX4 ACPI
    pci 0000:00:07.3: quirk: region 1040-104f claimed by PIIX4 SMB
    pci 0000:00:07.3: PIIX4 devres C PIO at 15e8-15ef
    pci 0000:00:07.3: PIIX4 devres I PIO at 03f0-03f7
    pci 0000:00:07.3: PIIX4 devres J PIO at 002e-002f
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11)
    ACPI: Power Resource [PSER] (off)
    ACPI: Power Resource [PSIO] (on)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp 00:00: mem resource (0x0-0x9ffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc0000-0xc3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc4000-0xc7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc8000-0xcbfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xcc000-0xcffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd0000-0xd3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd4000-0xd3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd8000-0xd7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xdc000-0xdbfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe0000-0xe3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe4000-0xe7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe8000-0xebfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xec000-0xeffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xf0000-0xfffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp: PnP ACPI: found 15 devices
    ACPI: ACPI bus type pnp unregistered
    PCI: Using ACPI for IRQ routing
    PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
    PCI: setting IRQ 5 as level-triggered
    ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
    PCI: setting IRQ 9 as level-triggered
    ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt 0000:00:03.1[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
    ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
    ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    ACPI: RTC can wake from S4
    system 00:00: iomem range 0x100000-0x1fffffff could not be reserved
    system 00:00: iomem range 0xfff80000-0xffffffff could not be reserved
    system 00:02: ioport range 0x1000-0x103f has been reserved
    system 00:02: ioport range 0x1040-0x104f has been reserved
    system 00:02: ioport range 0xfe00-0xfe0f has been reserved
    system 00:09: ioport range 0x15e0-0x15ef has been reserved
    PCI: Bridge: 0000:00:01.0
    IO window: 2000-2fff
    MEM window: 0xf0200000-0xf02fffff
    PREFETCH window: 0x00000000f8000000-0x00000000fbffffff
    PCI: Bus 2, cardbus bridge: 0000:00:02.0
    IO window: 0x00001400-0x000014ff
    IO window: 0x00001c00-0x00001cff
    PREFETCH window: 0x30000000-0x33ffffff
    MEM window: 0x34000000-0x37ffffff
    PCI: Bus 6, cardbus bridge: 0000:00:02.1
    IO window: 0x00003000-0x000030ff
    IO window: 0x00003400-0x000034ff
    PREFETCH window: 0x38000000-0x3bffffff
    MEM window: 0x3c000000-0x3fffffff
    ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    TCP: Hash tables configured (established 16384 bind 16384)
    TCP reno registered
    NET: Registered protocol family 1
    Unpacking initramfs... done
    Freeing initrd memory: 662k freed
    Simple Boot Flag at 0x35 set to 0x1
    IBM machine detected. Enabling interrupts during APM calls.
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    apm: overridden by ACPI.
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    msgmni has been set to 1006
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:00:00.0: Limiting direct PCI/PCI transfers
    pci 0000:00:03.0: Firmware left e100 interrupts enabled; disabling
    pci 0000:01:00.0: Boot video device
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    serial 00:0c: activated
    00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    ACPI: PCI Interrupt 0000:00:03.1[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
    input: Macintosh mouse button emulation as /class/input/input0
    PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP cubic registered
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    registered taskstats version 1
    Freeing unused kernel memory: 264k freed
    input: AT Translated Set 2 keyboard as /class/input/input1
    Switched to high resolution mode on CPU 0
    ACPI: ACPI Dock Station Driver
    SCSI subsystem initialized
    libata version 3.00 loaded.
    ata_piix 0000:00:07.1: version 2.12
    scsi0 : ata_piix
    scsi1 : ata_piix
    ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x1850 irq 14
    ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1858 irq 15
    ata1.00: ATA-6: TOSHIBA MK1032GAX, AB211A, max UDMA/100
    ata1.00: 195371568 sectors, multi 16: LBA48
    ata1.00: configured for UDMA/33
    ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-T20L, NR02, max UDMA/33
    ata2.00: configured for UDMA/33
    scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1032GA AB21 PQ: 0 ANSI: 5
    scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20L NR02 PQ: 0 ANSI: 5
    Driver 'sd' needs updating - please use bus_type methods
    sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda:<4>Driver 'sr' needs updating - please use bus_type methods
    sda1 sda2 sda3 sda4
    sd 0:0:0:0: [sda] Attached SCSI disk
    sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 1:0:0:0: Attached scsi CD-ROM sr0
    ReiserFS: sda2: found reiserfs format "3.6" with standard journal
    ReiserFS: sda2: using ordered data mode
    ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: sda2: checking transaction log (sda2)
    ReiserFS: sda2: Using r5 hash to sort names
    rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month, y3k
    Non-volatile memory driver v1.2
    thinkpad_acpi: ThinkPad ACPI Extras v0.20
    thinkpad_acpi: http://ibm-acpi.sf.net/
    thinkpad_acpi: ThinkPad BIOS 13ET14WW (1.00c), EC unknown
    Registered led device: tpacpi::thinklight
    thinkpad_acpi: another device driver is already handling bay events
    thinkpad_acpi: disabling subdriver bay
    Registered led device: tpacpi::power
    Registered led device: tpacpi:orange:batt
    Registered led device: tpacpi:green:batt
    Registered led device: tpacpi::dock_active
    Registered led device: tpacpi::bay_active
    Registered led device: tpacpi::dock_batt
    Registered led device: tpacpi::unknown_led
    Registered led device: tpacpi::standby
    input: ThinkPad Extra Buttons as /class/input/input2
    e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
    e100: Copyright(c) 1999-2006 Intel Corporation
    ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
    e100: eth0: e100_probe: addr 0xf0120000, irq 9, MAC addr 00:03:47:0f:de:3d
    eepro100.c:v1.09j-t 9/29/99 Donald Becker
    eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others
    ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    gameport: CS46xx Gameport is pci0000:00:05.0/gameport0, speed 1807kHz
    Linux agpgart interface v0.103
    agpgart: Detected an Intel 440BX Chipset.
    agpgart: AGP aperture is 64M @ 0xf4000000
    [drm] Initialized drm 1.1.0 20060810
    ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    [drm] Initialized r128 2.5.0 20030725 on minor 0
    ath_hal: module license 'Proprietary' taints kernel.
    AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
    fuse init (API version 7.9)
    Marking TSC unstable due to: cpufreq changes.
    /proc/exmap: insert
    ACPI: AC Adapter [AC] (on-line)
    ACPI: Battery Slot [BAT0] (battery present)
    input: Power Button (FF) as /class/input/input3
    ACPI: Power Button (FF) [PWRF]
    input: Lid Switch as /class/input/input4
    ACPI: Lid Switch [LID]
    input: Sleep Button (CM) as /class/input/input5
    ACPI: Sleep Button (CM) [SLPB]
    Clocksource tsc unstable (delta = 142842086 ns)
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    ACPI: ACPI0007:00 is registered as cooling_device0
    ACPI: Processor [CPU] (supports 8 throttling states)
    ACPI: LNXTHERM:01 is registered as thermal_zone0
    ACPI: Thermal Zone [THM0] (50 C)
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sr 1:0:0:0: Attached scsi generic sg1 type 5
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    Yenta: CardBus bridge found at 0000:00:02.0 [1014:0130]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:00:02.0, mfunc 0x00001000, devctl 0x66
    spurious 8259A interrupt: IRQ7.
    Yenta: ISA IRQ mask 0x0498, PCI irq 11
    Socket status: 30000020
    Yenta: CardBus bridge found at 0000:00:02.1 [1014:0130]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:00:02.1, mfunc 0x00001000, devctl 0x66
    Yenta: ISA IRQ mask 0x0498, PCI irq 5
    Socket status: 30000006
    pccard: CardBus card inserted into slot 0
    ath_pci 0000:02:00.0: enabling device (0000 -> 0002)
    ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    input: PC Speaker as /class/input/input6
    piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
    piix4_smbus 0000:00:07.3: IBM system detected; this module may corrupt your serial eeprom! Refusing to load module!
    piix4_smbus: probe of 0000:00:07.3 failed with error -1
    USB Universal Host Controller Interface driver v3.0
    ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
    uhci_hcd 0000:00:07.2: UHCI Host Controller
    uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:07.2: irq 5, io base 0x00001860
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    input: Video Bus as /class/input/input7
    ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
    IBM TrackPoint firmware: 0x0e, buttons: 3/3
    input: TPPS/2 IBM TrackPoint as /class/input/input8
    PPP generic driver version 2.4.2
    parport_pc 00:0d: activated
    parport_pc 00:0d: reported by Plug and Play ACPI
    parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
    NET: Registered protocol family 23
    nsc-ircc 00:0e: activated
    nsc-ircc, chip->init
    nsc-ircc, Found chip at base=0x02e
    nsc-ircc, driver loaded (Dag Brattli)
    IrDA: Registered device irda0
    nsc-ircc, Found dongle: Reserved
    MadWifi: ath_attach: Switching rfkill capability off.
    wifi0: Atheros AR2413 chip found (MAC 7.8, PHY 2112A 4.5, Radio 5.6)
    ath_pci: wifi0: Atheros 5212: mem=0x34000000, irq=11
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    lp0: using parport0 (interrupt-driven).
    ppdev: user-space parallel port driver
    JFS: nTxBlock = 4027, nTxLock = 32219
    Adding 1100444k swap on /dev/sda4. Priority:-1 extents:1 across:1100444k
    warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
    conservative governor failed, too long transition latency of HW, fallback to performance governor
    thinkpad_acpi: requested hot key mask 0x0000ffff, forced to 0x00008000 (NVRAM poll mask is 0x00fb8000): no firmware mask support
    I've tried multiple options in the BIOS. You can select AGP or PCI as the card for the root display device. The default is PCI so if there's a docked PCI card at POST, the BIOS will use that for the root display device... otherwise it will use the built in card. You can also select the root display device as LCD or CRT or both. The default is CRT so if there is an external monitor that's where the bootloader menu and such will appear, otherwise the laptop's own display gets used. Even if I've understood these incorrectly, all combinations yield a PCI video card that is not detected by lspci.
    I've also tried loading the module dock right after thinkpad_acpi. It loads and appears in lsmod but it doesn't help the situation at all. It also doesn't add a dock file to /proc/acpi/ibm. I also tried passing pci=routirq to the kernel, whatever that does and I've tried changing the four PCI related IRQ numbers in the BIOS and this has not helped.

    I did upgrade the kernel yesterday and it caused the syntax of dmesg to change somewhat. Here is a docked dmesg from 2.6.27:
    Linux version 2.6.27-ARCH (root@architect) (gcc version 4.3.2 (GCC) ) #1 SMP PREEMPT Sun Oct 12 15:16:25 CEST 2008
    PAT WC disabled due to known CPU erratum.
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    BIOS-e820: 000000001fff0000 - 000000001fffec00 (ACPI data)
    BIOS-e820: 000000001fffec00 - 0000000020000000 (ACPI NVS)
    BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    last_pfn = 0x1fff0 max_arch_pfn = 0x100000
    kernel direct mapping tables up to 1fff0000 @ 7000-d000
    RAMDISK: 00e4d000 - 00effb5b
    DMI 2.3 present.
    ACPI: RSDP 000F7160, 0014 (r0 PTLTD )
    ACPI: RSDT 1FFF53D5, 002C (r1 PTLTD RSDT 6040000 LTP 0)
    ACPI: FACP 1FFFEB65, 0074 (r1 IBM TP-13 6040000 0)
    ACPI: DSDT 1FFF5401, 9764 (r1 IBM TP-13 6040000 MSFT 100000C)
    ACPI: FACS 1FFFF000, 0040
    ACPI: BOOT 1FFFEBD9, 0027 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
    0MB HIGHMEM available.
    511MB LOWMEM available.
    mapped low ram: 0 - 1fff0000
    low ram: 00000000 - 1fff0000
    bootmap 00002000 - 00006000
    (9 early reservations) ==> bootmem [0000000000 - 001fff0000]
    #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
    #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
    #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
    #3 [0000100000 - 000050c280] TEXT DATA BSS ==> [0000100000 - 000050c280]
    #4 [0000e4d000 - 0000effb5b] RAMDISK ==> [0000e4d000 - 0000effb5b]
    #5 [000050d000 - 0000510000] INIT_PG_TABLE ==> [000050d000 - 0000510000]
    #6 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
    #7 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000]
    #8 [0000002000 - 0000006000] BOOTMAP ==> [0000002000 - 0000006000]
    Zone PFN ranges:
    DMA 0x00000000 -> 0x00001000
    Normal 0x00001000 -> 0x0001fff0
    HighMem 0x0001fff0 -> 0x0001fff0
    Movable zone start PFN for each node
    early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x0000009f
    0: 0x00000100 -> 0x0001fff0
    On node 0 totalpages: 130959
    free_area_init_node: node 0, pgdat c03d9580, node_mem_map c1000000
    DMA zone: 3967 pages, LIFO batch:0
    Normal zone: 125968 pages, LIFO batch:31
    ACPI: PM-Timer IO Port: 0x1008
    SMP: Allowing 1 CPUs, 0 hotplug CPUs
    Local APIC disabled by BIOS -- you can enable it with "lapic"
    mapped APIC to ffffb000 (01402000)
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
    Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000)
    PERCPU: Allocating 39324 bytes of per cpu data
    NR_CPUS: 16, nr_cpu_ids: 1, nr_node_ids 1
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129935
    Kernel command line: BOOT_IMAGE=arch ro root=802 hpet=force pci=routeirq acpi_osi=Linux panic=10
    ACPI: Added _OSI(Linux)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 2048 (order: 11, 8192 bytes)
    TSC: PIT calibration confirmed by PMTIMER.
    TSC: using PIT calibration value
    Detected 697.407 MHz processor.
    Console: colour VGA+ 80x25
    console [tty0] enabled
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Memory: 514248k/524224k available (2151k kernel code, 9460k reserved, 844k data, 288k init, 0k highmem)
    virtual kernel memory layout:
    fixmap : 0xffee8000 - 0xfffff000 (1116 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
    lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
    .init : 0xc03f3000 - 0xc043b000 ( 288 kB)
    .data : 0xc0319f76 - 0xc03ed360 ( 844 kB)
    .text : 0xc0100000 - 0xc0319f76 (2151 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    CPA: page pool initialized 1 of 1 pages preallocated
    SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    Calibrating delay loop (skipped), value calculated using timer frequency.. 1395.93 BogoMIPS (lpj=2324690)
    Security Framework initialized
    Mount-cache hash table entries: 512
    CPU: L1 I cache: 16K, L1 D cache: 16K
    CPU: L2 cache: 256K
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    Freeing SMP alternatives: 9k freed
    ACPI: Core revision 20080609
    ACPI: Checking initramfs for custom DSDT
    ACPI: setting ELCR to 0200 (from 0e00)
    weird, boot CPU (#0) not listedby the BIOS.
    SMP motherboard not detected.
    Local APIC not detected. Using dummy APIC emulation.
    SMP disabled
    Brought up 1 CPUs
    Total of 1 processors activated (1395.93 BogoMIPS).
    net_namespace: 832 bytes
    Booting paravirtualized kernel on bare hardware
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=14
    PCI: Using configuration type 1 for base access
    ACPI: EC: Look up EC in DSDT
    ACPI: EC: non-query interrupt received, switching to interrupt mode
    ACPI: Interpreter enabled
    ACPI: (supports S0 S1 S3 S4 S5)
    ACPI: Using PIC for interrupt routing
    ACPI: EC: GPE = 0x9, I/O: command/status = 0x66, data = 0x62
    ACPI: EC: driver started in interrupt mode
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: 0000:00:00.0 reg 10 32bit mmio: [f4000000, f7ffffff]
    PCI: 0000:00:02.0 reg 10 32bit mmio: [50000000, 50000fff]
    pci 0000:00:02.0: supports D1
    pci 0000:00:02.0: supports D2
    pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:02.0: PME# disabled
    PCI: 0000:00:02.1 reg 10 32bit mmio: [50100000, 50100fff]
    pci 0000:00:02.1: supports D1
    pci 0000:00:02.1: supports D2
    pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:02.1: PME# disabled
    PCI: 0000:00:03.0 reg 10 32bit mmio: [f0120000, f0120fff]
    PCI: 0000:00:03.0 reg 14 io port: [1800, 183f]
    PCI: 0000:00:03.0 reg 18 32bit mmio: [f0100000, f011ffff]
    PCI: 0000:00:03.0 reg 30 32bit mmio: [0, fffff]
    pci 0000:00:03.0: supports D1
    pci 0000:00:03.0: supports D2
    pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:03.0: PME# disabled
    PCI: 0000:00:03.1 reg 10 io port: [1840, 1847]
    PCI: 0000:00:03.1 reg 14 32bit mmio: [f0121000, f0121fff]
    pci 0000:00:03.1: supports D1
    pci 0000:00:03.1: supports D2
    pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:03.1: PME# disabled
    pci 0000:00:04.0: supports D1
    pci 0000:00:04.0: supports D2
    PCI: 0000:00:05.0 reg 10 32bit mmio: [f0122000, f0122fff]
    PCI: 0000:00:05.0 reg 14 32bit mmio: [f0000000, f00fffff]
    pci 0000:00:05.0: supports D1
    pci 0000:00:05.0: supports D2
    PCI: 0000:00:07.1 reg 20 io port: [1850, 185f]
    PCI: 0000:00:07.2 reg 20 io port: [1860, 187f]
    pci 0000:00:07.3: quirk: region 1000-103f claimed by PIIX4 ACPI
    pci 0000:00:07.3: quirk: region 1040-104f claimed by PIIX4 SMB
    pci 0000:00:07.3: PIIX4 devres C PIO at 15e8-15ef
    pci 0000:00:07.3: PIIX4 devres I PIO at 03f0-03f7
    pci 0000:00:07.3: PIIX4 devres J PIO at 002e-002f
    PCI: 0000:01:00.0 reg 10 32bit mmio: [f8000000, fbffffff]
    PCI: 0000:01:00.0 reg 14 io port: [2000, 20ff]
    PCI: 0000:01:00.0 reg 18 32bit mmio: [f0200000, f0203fff]
    PCI: 0000:01:00.0 reg 30 32bit mmio: [0, 1ffff]
    pci 0000:01:00.0: supports D1
    pci 0000:01:00.0: supports D2
    PCI: bridge 0000:00:01.0 io port: [2000, 2fff]
    PCI: bridge 0000:00:01.0 32bit mmio: [f0200000, f02fffff]
    PCI: bridge 0000:00:01.0 32bit mmio pref: [f8000000, fbffffff]
    PCI: 0000:08:01.0 reg 10 io port: [3020, 3027]
    PCI: 0000:08:01.0 reg 14 io port: [3014, 3017]
    PCI: 0000:08:01.0 reg 18 io port: [3018, 301f]
    PCI: 0000:08:01.0 reg 1c io port: [3010, 3013]
    PCI: 0000:08:01.0 reg 20 io port: [3000, 300f]
    pci 0000:08:01.0: supports D1
    pci 0000:08:01.0: supports D2
    PCI: 0000:08:02.0 reg 10 32bit mmio: [52000000, 52000fff]
    pci 0000:08:02.0: supports D1
    pci 0000:08:02.0: supports D2
    pci 0000:08:02.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:08:02.0: PME# disabled
    PCI: 0000:08:02.1 reg 10 32bit mmio: [53000000, 53000fff]
    pci 0000:08:02.1: supports D1
    pci 0000:08:02.1: supports D2
    pci 0000:08:02.1: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:08:02.1: PME# disabled
    pci 0000:00:04.0: transparent bridge
    PCI: bridge 0000:00:04.0 io port: [0, fff]
    PCI: bridge 0000:00:04.0 32bit mmio: [0, fffff]
    PCI: bridge 0000:00:04.0 32bit mmio pref: [0, fffff]
    bus 00 -> node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.DOCK._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11)
    ACPI: Power Resource [PSER] (off)
    ACPI: Power Resource [PSIO] (on)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp 00:00: mem resource (0x0-0x9ffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc0000-0xc3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc4000-0xc7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc8000-0xcbfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xcc000-0xcffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd0000-0xd3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd4000-0xd3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd8000-0xd7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xdc000-0xdbfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe0000-0xe3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe4000-0xe7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe8000-0xebfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xec000-0xeffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xf0000-0xfffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0x0-0x9ffff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc0000-0xc3fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc4000-0xc7fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc8000-0xcbfff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xcc000-0xcffff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd0000-0xd3fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd4000-0xd3fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd8000-0xd7fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xdc000-0xdbfff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe0000-0xe3fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe4000-0xe7fff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe8000-0xebfff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xec000-0xeffff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xf0000-0xfffff) overlaps 0000:00:04.0 BAR 8 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0x0-0x9ffff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc0000-0xc3fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc4000-0xc7fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc8000-0xcbfff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xcc000-0xcffff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd0000-0xd3fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd4000-0xd3fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd8000-0xd7fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xdc000-0xdbfff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe0000-0xe3fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe4000-0xe7fff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe8000-0xebfff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xec000-0xeffff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xf0000-0xfffff) overlaps 0000:00:04.0 BAR 9 (0x0-0xfffff), disabling
    pnp 00:02: io resource (0x22-0x22) overlaps 0000:00:04.0 BAR 7 (0x0-0xfff), disabling
    pnp 00:02: io resource (0x92-0x92) overlaps 0000:00:04.0 BAR 7 (0x0-0xfff), disabling
    pnp 00:02: io resource (0xb2-0xb3) overlaps 0000:00:04.0 BAR 7 (0x0-0xfff), disabling
    pnp 00:0a: io resource (0x2e-0x2f) overlaps 0000:00:04.0 BAR 7 (0x0-0xfff), disabling
    pnp: PnP ACPI: found 15 devices
    ACPI: ACPI bus type pnp unregistered
    PCI: Using ACPI for IRQ routing
    PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
    PCI: setting IRQ 9 as level-triggered
    pci 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
    pci 0000:00:02.1: PCI INT B -> Link[LNKB] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    pci 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    pci 0000:00:03.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    pci 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
    PCI: setting IRQ 10 as level-triggered
    pci 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10
    pci 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    pci 0000:08:01.0: PCI INT A -> Link[LNKB] -> GSI 9 (level, low) -> IRQ 9
    pci 0000:08:02.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    pci 0000:08:02.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    pci 0000:00:04.0: BAR 7: can't allocate resource
    pci 0000:00:04.0: BAR 8: can't allocate resource
    pci 0000:00:04.0: BAR 9: can't allocate resource
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    ACPI: RTC can wake from S4
    system 00:00: iomem range 0x100000-0x1fffffff could not be reserved
    system 00:00: iomem range 0xfff80000-0xffffffff could not be reserved
    system 00:02: ioport range 0x1000-0x103f has been reserved
    system 00:02: ioport range 0x1040-0x104f has been reserved
    system 00:02: ioport range 0xfe00-0xfe0f has been reserved
    system 00:09: ioport range 0x15e0-0x15ef has been reserved
    pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
    pci 0000:00:01.0: IO window: 0x2000-0x2fff
    pci 0000:00:01.0: MEM window: 0xf0200000-0xf02fffff
    pci 0000:00:01.0: PREFETCH window: 0x000000f8000000-0x000000fbffffff
    pci 0000:00:02.0: CardBus bridge, secondary bus 0000:0f
    pci 0000:00:02.0: IO window: 0x001400-0x0014ff
    pci 0000:00:02.0: IO window: 0x001c00-0x001cff
    pci 0000:00:02.0: PREFETCH window: 0x30000000-0x33ffffff
    pci 0000:00:02.0: MEM window: 0x34000000-0x37ffffff
    pci 0000:00:02.1: CardBus bridge, secondary bus 0000:13
    pci 0000:00:02.1: IO window: 0x003400-0x0034ff
    pci 0000:00:02.1: IO window: 0x003800-0x0038ff
    pci 0000:00:02.1: PREFETCH window: 0x38000000-0x3bffffff
    pci 0000:00:02.1: MEM window: 0x3c000000-0x3fffffff
    pci 0000:08:02.0: CardBus bridge, secondary bus 0000:09
    pci 0000:08:02.0: IO window: 0x004000-0x0040ff
    pci 0000:08:02.0: IO window: 0x004400-0x0044ff
    pci 0000:08:02.0: PREFETCH window: 0x48000000-0x4bffffff
    pci 0000:08:02.0: MEM window: 0x40000000-0x43ffffff
    pci 0000:08:02.1: CardBus bridge, secondary bus 0000:0d
    pci 0000:08:02.1: IO window: 0x004800-0x0048ff
    pci 0000:08:02.1: IO window: 0x004c00-0x004cff
    pci 0000:08:02.1: PREFETCH window: 0x4c000000-0x4fffffff
    pci 0000:08:02.1: MEM window: 0x44000000-0x47ffffff
    pci 0000:00:04.0: PCI bridge, secondary bus 0000:08
    pci 0000:00:04.0: IO window: 0x4000-0x4fff
    pci 0000:00:04.0: MEM window: 0x40000000-0x47ffffff
    pci 0000:00:04.0: PREFETCH window: 0x00000048000000-0x0000004fffffff
    pci 0000:00:02.0: power state changed by ACPI to D0
    pci 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    pci 0000:00:02.1: power state changed by ACPI to D0
    pci 0000:00:02.1: PCI INT B -> Link[LNKB] -> GSI 9 (level, low) -> IRQ 9
    pci 0000:08:02.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    pci 0000:08:02.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    bus: 00 index 0 io port: [0, ffff]
    bus: 00 index 1 mmio: [0, ffffffff]
    bus: 01 index 0 io port: [2000, 2fff]
    bus: 01 index 1 mmio: [f0200000, f02fffff]
    bus: 01 index 2 mmio: [f8000000, fbffffff]
    bus: 01 index 3 mmio: [0, 0]
    bus: 0f index 0 io port: [1400, 14ff]
    bus: 0f index 1 io port: [1c00, 1cff]
    bus: 0f index 2 mmio: [30000000, 33ffffff]
    bus: 0f index 3 mmio: [34000000, 37ffffff]
    bus: 13 index 0 io port: [3400, 34ff]
    bus: 13 index 1 io port: [3800, 38ff]
    bus: 13 index 2 mmio: [38000000, 3bffffff]
    bus: 13 index 3 mmio: [3c000000, 3fffffff]
    bus: 08 index 0 io port: [4000, 4fff]
    bus: 08 index 1 mmio: [40000000, 47ffffff]
    bus: 08 index 2 mmio: [48000000, 4fffffff]
    bus: 08 index 3 io port: [0, ffff]
    bus: 08 index 4 mmio: [0, ffffffff]
    bus: 09 index 0 io port: [4000, 40ff]
    bus: 09 index 1 io port: [4400, 44ff]
    bus: 09 index 2 mmio: [48000000, 4bffffff]
    bus: 09 index 3 mmio: [40000000, 43ffffff]
    bus: 0d index 0 io port: [4800, 48ff]
    bus: 0d index 1 io port: [4c00, 4cff]
    bus: 0d index 2 mmio: [4c000000, 4fffffff]
    bus: 0d index 3 mmio: [44000000, 47ffffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    TCP: Hash tables configured (established 16384 bind 16384)
    TCP reno registered
    NET: Registered protocol family 1
    Unpacking initramfs... done
    Freeing initrd memory: 714k freed
    Simple Boot Flag at 0x35 set to 0x1
    IBM machine detected. Enabling interrupts during APM calls.
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    apm: overridden by ACPI.
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    msgmni has been set to 1006
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:00:00.0: Limiting direct PCI/PCI transfers
    pci 0000:00:03.0: Firmware left e100 interrupts enabled; disabling
    pci 0000:01:00.0: Boot video device
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver4 ports, IRQ sharing disabled
    serial 00:0c: activated
    00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    serial 0000:00:03.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    input: Macintosh mouse button emulation as /class/input/input0
    PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP cubic registered
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    registered taskstats version 1
    Freeing unused kernel memory: 288k freed
    Switched to high resolution mode on CPU 0
    input: AT Translated Set 2 keyboard as /class/input/input1
    ACPI: ACPI Dock Station Driver
    SCSI subsystem initialized
    libata version 3.00 loaded.
    ata_piix 0000:00:07.1: version 2.12
    scsi0 : ata_piix
    scsi1 : ata_piix
    ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x1850 irq 14
    ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1858 irq 15
    ata1.00: ATA-6: TOSHIBA MK1032GAX, AB211A, max UDMA/100
    ata1.00: 195371568 sectors, multi 16: LBA48
    ata1.00: configured for UDMA/33
    ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-T20L, NR02, max UDMA/33
    ata2.00: configured for UDMA/33
    scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1032GA AB21 PQ: 0 ANSI: 5
    scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20L NR02 PQ: 0 ANSI: 5
    pata_acpi 0000:08:01.0: PCI INT A -> Link[LNKB] -> GSI 9 (level, low) -> IRQ 9
    pata_acpi 0000:08:01.0: PCI INT A disabled
    Driver 'sd' needs updating - please use bus_type methods
    sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda: sda1 sda2 sda3 sda4
    Driver 'sr' needs updating - please use bus_type methods
    sd 0:0:0:0: [sda] Attached SCSI disk
    sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 1:0:0:0: Attached scsi CD-ROM sr0
    ReiserFS: sda2: found reiserfs format "3.6" with standard journal
    ReiserFS: sda2: using ordered data mode
    ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: sda2: checking transaction log (sda2)
    ReiserFS: sda2: Using r5 hash to sort names
    rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month, y3k
    Non-volatile memory driver v1.2
    thinkpad_acpi: ThinkPad ACPI Extras v0.21
    thinkpad_acpi: http://ibm-acpi.sf.net/
    thinkpad_acpi: ThinkPad BIOS 13ET14WW (1.00c), EC unknown
    Registered led device: tpacpi::thinklight
    thinkpad_acpi: another device driver is already handling bay events
    thinkpad_acpi: disabling subdriver bay
    Registered led device: tpacpi::power
    Registered led device: tpacpi:orange:batt
    Registered led device: tpacpi:green:batt
    Registered led device: tpacpi::dock_active
    Registered led device: tpacpi::bay_active
    Registered led device: tpacpi::dock_batt
    Registered led device: tpacpi::unknown_led
    Registered led device: tpacpi::standby
    input: ThinkPad Extra Buttons as /class/input/input2
    e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
    e100: Copyright(c) 1999-2006 Intel Corporation
    e100 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    e100 0000:00:03.0: PME# disabled
    e100: eth0: e100_probe: addr 0xf0120000, irq 11, MAC addr 00:03:47:0f:de:3d
    eepro100.c:v1.09j-t 9/29/99 Donald Becker
    eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others
    Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    gameport: CS46xx Gameport is pci0000:00:05.0/gameport0, speed 1807kHz
    Linux agpgart interface v0.103
    agpgart-intel 0000:00:00.0: Intel 440BX Chipset
    agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf4000000
    [drm] Initialized drm 1.1.0 20060810
    pci 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    [drm] Initialized r128 2.5.0 20030725 on minor 0
    ath_hal: module license 'Proprietary' taints kernel.
    AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
    fuse init (API version 7.9)
    Marking TSC unstable due to cpufreq changes
    ACPI: AC Adapter [AC] (on-line)
    ACPI: Battery Slot [BAT0] (battery present)
    input: Power Button (FF) as /class/input/input3
    ACPI: Power Button (FF) [PWRF]
    input: Lid Switch as /class/input/input4
    ACPI: Lid Switch [LID]
    input: Sleep Button (CM) as /class/input/input5
    ACPI: Sleep Button (CM) [SLPB]
    Clocksource tsc unstable (delta = 142865538 ns)
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    processor ACPI0007:00: registered as cooling_device0
    ACPI: Processor [CPU] (supports 8 throttling states)
    thermal LNXTHERM:01: registered as thermal_zone0
    ACPI: Thermal Zone [THM0] (24 C)
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sr 1:0:0:0: Attached scsi generic sg1 type 5
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    Yenta: CardBus bridge found at 0000:00:02.0 [1014:0130]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:00:02.0, mfunc 0x00001000, devctl 0x66
    Yenta: ISA IRQ mask 0x00b8, PCI irq 9
    Socket status: 30000020
    Yenta: CardBus bridge found at 0000:00:02.1 [1014:0130]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:00:02.1, mfunc 0x00001000, devctl 0x66
    Yenta: ISA IRQ mask 0x00b8, PCI irq 9
    Socket status: 30000006
    Yenta: CardBus bridge found at 0000:08:02.0 [1014:0148]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:08:02.0, mfunc 0x00001002, devctl 0x66
    irq 9: nobody cared (try booting with the "irqpoll" option)
    Pid: 1302, comm: modprobe Tainted: P 2.6.27-ARCH #1
    [<c015ce54>] __report_bad_irq+0x24/0x90
    [<c015d142>] note_interrupt+0x282/0x2c0
    [<c015c450>] handle_IRQ_event+0x30/0x60
    [<c015d9b3>] handle_level_irq+0xd3/0x100
    [<c010710b>] do_IRQ+0x3b/0x70
    [<c0104927>] common_interrupt+0x23/0x28
    [<c03100d8>] cache_add_dev+0x272/0x44a
    [<c015c430>] handle_IRQ_event+0x10/0x60
    [<c015d95d>] handle_level_irq+0x7d/0x100
    [<c010710b>] do_IRQ+0x3b/0x70
    [<c015cbc1>] setup_irq+0x121/0x250
    [<c0104927>] common_interrupt+0x23/0x28
    [<c015007b>] rt_mutex_adjust_prio_chain+0x20b/0x340
    [<e0c168cc>] yenta_probe_cb_irq+0x9c/0x110 [yenta_socket]
    [<e0c16c58>] ti12xx_override+0x238/0x6a0 [yenta_socket]
    [<e0c17fe2>] yenta_probe+0x622/0x673 [yenta_socket]
    [<c01d4012>] sysfs_add_one+0x12/0x50
    [<c01d40bd>] sysfs_addrm_start+0x6d/0xc0
    [<c0318f05>] _spin_unlock+0x5/0x20
    [<c020bce0>] pci_match_device+0xa0/0xc0
    [<c020c4b6>] pci_device_probe+0x56/0x80
    [<c026da76>] driver_probe_device+0x86/0x1a0
    [<c0318af4>] _spin_lock_irqsave+0x34/0x50
    [<c026dc01>] __driver_attach+0x71/0x80
    [<c020c400>] pci_device_remove+0x0/0x40
    [<c026d3a4>] bus_for_each_dev+0x44/0x70
    [<c020c400>] pci_device_remove+0x0/0x40
    [<c026d906>] driver_attach+0x16/0x20
    [<c026db90>] __driver_attach+0x0/0x80
    [<c026cd37>] bus_add_driver+0x1a7/0x220
    [<c020c400>] pci_device_remove+0x0/0x40
    [<c026dd9c>] driver_register+0x5c/0x130
    [<e08be000>] yenta_socket_init+0x0/0x14 [yenta_socket]
    [<c020c6f7>] __pci_register_driver+0x47/0x90
    [<e08be000>] yenta_socket_init+0x0/0x14 [yenta_socket]
    [<c010111a>] do_one_initcall+0x2a/0x160
    [<c0123480>] hrtick_start_fair+0x190/0x1b0
    [<c0126635>] check_preempt_wakeup+0xe5/0x120
    [<c0126def>] try_to_wake_up+0xaf/0x180
    [<c015474b>] sys_init_module+0x8b/0x1b0
    [<c0103ef3>] sysenter_do_call+0x12/0x33
    =======================
    handlers:
    [<c0229cfc>] (acpi_irq+0x0/0x1f)
    [<e0a663c0>] (snd_cs46xx_interrupt+0x0/0x1f0 [snd_cs46xx])
    [<e0c17880>] (yenta_interrupt+0x0/0xf0 [yenta_socket])
    [<e0c17880>] (yenta_interrupt+0x0/0xf0 [yenta_socket])
    Disabling IRQ #9
    pccard: CardBus card inserted into slot 0
    PCI: 0000:0f:00.0 reg 10 32bit mmio: [0, ffff]
    ath_pci 0000:0f:00.0: enabling device (0000 -> 0002)
    ath_pci 0000:0f:00.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    input: PC Speaker as /class/input/input6
    USB Universal Host Controller Interface driver v3.0
    input: Video Bus as /class/input/input7
    ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
    Error: Driver 'pcspkr' is already registered, aborting...
    NET: Registered protocol family 23
    IBM TrackPoint firmware: 0x0e, buttons: 3/3
    input: TPPS/2 IBM TrackPoint as /class/input/input8
    parport_pc 00:0d: activated
    parport_pc 00:0d: reported by Plug and Play ACPI
    parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
    nsc-ircc 00:0e: activated
    nsc-ircc, chip->init
    nsc-ircc, Found chip at base=0x02e
    nsc-ircc, driver loaded (Dag Brattli)
    IrDA: Registered device irda0
    nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500
    PPP generic driver version 2.4.2
    Uniform Multi-Platform E-IDE driver
    MadWifi: ath_attach: Switching rfkill capability off.
    wifi0: Atheros AR2413 chip found (MAC 7.8, PHY 2112A 4.5, Radio 5.6)
    ppdev: user-space parallel port driver
    ath_pci: wifi0: Atheros 5212: mem=0x34000000, irq=9
    Yenta: ISA IRQ mask 0x0038, PCI irq 11
    Socket status: 30000006
    pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
    cs: IO port probe 0x4000-0x4fff: clean.
    pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x47ffffff
    pcmcia: parent PCI bridge Memory window: 0x48000000 - 0x4fffffff
    cmd64x 0000:08:01.0: IDE controller (0x1095:0x0648 rev 0x01)
    CMD64x_IDE 0000:08:01.0: PCI INT A -> Link[LNKB] -> GSI 9 (level, low) -> IRQ 9
    cmd64x 0000:08:01.0: 100% native mode on irq 9
    ide0: BM-DMA at 0x3000-0x3007
    ide1: BM-DMA at 0x3008-0x300f
    Probing IDE interface ide0...
    Probing IDE interface ide1...
    ide0 at 0x3020-0x3027,0x3016 on irq 9
    ide1 at 0x3018-0x301f,0x3012 on irq 9
    piix4_smbus 0000:00:07.3: IBM system detected; this module may corrupt your serial eeprom! Refusing to load module!
    piix4_smbus: probe of 0000:00:07.3 failed with error -1
    Yenta: CardBus bridge found at 0000:08:02.1 [1014:0148]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:08:02.1, mfunc 0x00001002, devctl 0x66
    irq 9: nobody cared (try booting with the "irqpoll" option)
    Pid: 1302, comm: modprobe Tainted: P 2.6.27-ARCH #1
    [<c015ce54>] __report_bad_irq+0x24/0x90
    [<c015d142>] note_interrupt+0x282/0x2c0
    [<c015c450>] handle_IRQ_event+0x30/0x60
    [<c015d9b3>] handle_level_irq+0xd3/0x100
    [<c010710b>] do_IRQ+0x3b/0x70
    [<c0104927>] common_interrupt+0x23/0x28
    [<c031007b>] cache_add_dev+0x215/0x44a
    [<c03100d8>] cache_add_dev+0x272/0x44a
    [<c015c430>] handle_IRQ_event+0x10/0x60
    [<c015d95d>] handle_level_irq+0x7d/0x100
    [<c010710b>] do_IRQ+0x3b/0x70
    [<c015cbc1>] setup_irq+0x121/0x250
    [<c0104927>] common_interrupt+0x23/0x28
    [<c015007b>] rt_mutex_adjust_prio_chain+0x20b/0x340
    [<e0c168cc>] yenta_probe_cb_irq+0x9c/0x110 [yenta_socket]
    [<e0c16b97>] ti12xx_override+0x177/0x6a0 [yenta_socket]
    [<e0c17fe2>] yenta_probe+0x622/0x673 [yenta_socket]
    [<c01d4012>] sysfs_add_one+0x12/0x50
    [<c01d40bd>] sysfs_addrm_start+0x6d/0xc0
    [<c0318f05>] _spin_unlock+0x5/0x20
    [<c020bce0>] pci_match_device+0xa0/0xc0
    [<c020c4b6>] pci_device_probe+0x56/0x80
    [<c026da76>] driver_probe_device+0x86/0x1a0
    [<c0318af4>] _spin_lock_irqsave+0x34/0x50
    [<c026dc01>] __driver_attach+0x71/0x80
    [<c020c400>] pci_device_remove+0x0/0x40
    [<c026d3a4>] bus_for_each_dev+0x44/0x70
    [<c020c400>] pci_device_remove+0x0/0x40
    [<c026d906>] driver_attach+0x16/0x20
    [<c026db90>] __driver_attach+0x0/0x80
    [<c026cd37>] bus_add_driver+0x1a7/0x220
    [<c020c400>] pci_device_remove+0x0/0x40
    [<c026dd9c>] driver_register+0x5c/0x130
    [<e08be000>] yenta_socket_init+0x0/0x14 [yenta_socket]
    [<c020c6f7>] __pci_register_driver+0x47/0x90
    [<e08be000>] yenta_socket_init+0x0/0x14 [yenta_socket]
    [<c010111a>] do_one_initcall+0x2a/0x160
    [<c0123480>] hrtick_start_fair+0x190/0x1b0
    [<c0126635>] check_preempt_wakeup+0xe5/0x120
    [<c0126def>] try_to_wake_up+0xaf/0x180
    [<c015474b>] sys_init_module+0x8b/0x1b0
    [<c0103ef3>] sysenter_do_call+0x12/0x33
    =======================
    handlers:
    [<c0229cfc>] (acpi_irq+0x0/0x1f)
    [<e0a663c0>] (snd_cs46xx_interrupt+0x0/0x1f0 [snd_cs46xx])
    [<e0c17880>] (yenta_interrupt+0x0/0xf0 [yenta_socket])
    [<e0c17880>] (yenta_interrupt+0x0/0xf0 [yenta_socket])
    [<e0b3fdf0>] (ath_intr+0x0/0x4880 [ath_pci])
    [<e0cf28a0>] (ide_intr+0x0/0x220 [ide_core])
    [<e0cf28a0>] (ide_intr+0x0/0x220 [ide_core])
    Disabling IRQ #9
    Yenta: ISA IRQ mask 0x0038, PCI irq 11
    Socket status: 30000006
    pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
    cs: IO port probe 0x4000-0x4fff: clean.
    pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x47ffffff
    pcmcia: parent PCI bridge Memory window: 0x48000000 - 0x4fffffff
    uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10
    uhci_hcd 0000:00:07.2: UHCI Host Controller
    uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:07.2: irq 10, io base 0x00001860
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    usb 1-1: new full speed USB device using uhci_hcd and address 2
    usb 1-1: configuration #1 chosen from 1 choice
    hub 1-1:1.0: USB hub found
    hub 1-1:1.0: 4 ports detected
    lp0: using parport0 (interrupt-driven).
    usb 1-1.4: new low speed USB device using uhci_hcd and address 3
    usb 1-1.4: configuration #1 chosen from 1 choice
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    usbcore: registered new interface driver hiddev
    input: Logitech Logitech USB Optical Mouse as /class/input/input9
    input,hidraw0: USB HID v1.11 Mouse [Logitech Logitech USB Optical Mouse] on usb-0000:00:07.2-1.4
    usbcore: registered new interface driver usbhid
    usbhid: v2.6:USB HID core driver
    ACPI: EC: missing confirmations, switch off interrupt mode.
    JFS: nTxBlock = 4026, nTxLock = 32211
    Adding 1100444k swap on /dev/sda4. Priority:-1 extents:1 across:1100444k
    warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
    conservative governor failed, too long transition latency of HW, fallback to performance governor
    thinkpad_acpi: requested hot key mask 0x0000ffff, forced to 0x00008000 (NVRAM poll mask is 0x00fb8000): no firmware mask support
    Note the "can't allocate resource areas"... And here is the new dockless dmesg:
    Linux version 2.6.27-ARCH (root@architect) (gcc version 4.3.2 (GCC) ) #1 SMP PREEMPT Sun Oct 12 15:16:25 CEST 2008
    PAT WC disabled due to known CPU erratum.
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    BIOS-e820: 000000001fff0000 - 000000001fffec00 (ACPI data)
    BIOS-e820: 000000001fffec00 - 0000000020000000 (ACPI NVS)
    BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    last_pfn = 0x1fff0 max_arch_pfn = 0x100000
    kernel direct mapping tables up to 1fff0000 @ 7000-d000
    RAMDISK: 00e4d000 - 00effb5b
    DMI 2.3 present.
    ACPI: RSDP 000F7160, 0014 (r0 PTLTD )
    ACPI: RSDT 1FFF53D5, 002C (r1 PTLTD RSDT 6040000 LTP 0)
    ACPI: FACP 1FFFEB65, 0074 (r1 IBM TP-13 6040000 0)
    ACPI: DSDT 1FFF5401, 9764 (r1 IBM TP-13 6040000 MSFT 100000C)
    ACPI: FACS 1FFFF000, 0040
    ACPI: BOOT 1FFFEBD9, 0027 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
    0MB HIGHMEM available.
    511MB LOWMEM available.
    mapped low ram: 0 - 1fff0000
    low ram: 00000000 - 1fff0000
    bootmap 00002000 - 00006000
    (9 early reservations) ==> bootmem [0000000000 - 001fff0000]
    #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
    #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
    #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
    #3 [0000100000 - 000050c280] TEXT DATA BSS ==> [0000100000 - 000050c280]
    #4 [0000e4d000 - 0000effb5b] RAMDISK ==> [0000e4d000 - 0000effb5b]
    #5 [000050d000 - 0000510000] INIT_PG_TABLE ==> [000050d000 - 0000510000]
    #6 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
    #7 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000]
    #8 [0000002000 - 0000006000] BOOTMAP ==> [0000002000 - 0000006000]
    Zone PFN ranges:
    DMA 0x00000000 -> 0x00001000
    Normal 0x00001000 -> 0x0001fff0
    HighMem 0x0001fff0 -> 0x0001fff0
    Movable zone start PFN for each node
    early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x0000009f
    0: 0x00000100 -> 0x0001fff0
    On node 0 totalpages: 130959
    free_area_init_node: node 0, pgdat c03d9580, node_mem_map c1000000
    DMA zone: 3967 pages, LIFO batch:0
    Normal zone: 125968 pages, LIFO batch:31
    ACPI: PM-Timer IO Port: 0x1008
    SMP: Allowing 1 CPUs, 0 hotplug CPUs
    Local APIC disabled by BIOS -- you can enable it with "lapic"
    mapped APIC to ffffb000 (01402000)
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
    Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000)
    PERCPU: Allocating 39324 bytes of per cpu data
    NR_CPUS: 16, nr_cpu_ids: 1, nr_node_ids 1
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129935
    Kernel command line: BOOT_IMAGE=arch ro root=802 hpet=force pci=routeirq acpi_osi=Linux panic=10
    ACPI: Added _OSI(Linux)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 2048 (order: 11, 8192 bytes)
    TSC: PIT calibration confirmed by PMTIMER.
    TSC: using PIT calibration value
    Detected 697.409 MHz processor.
    Console: colour VGA+ 80x25
    console [tty0] enabled
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Memory: 514248k/524224k available (2151k kernel code, 9460k reserved, 844k data, 288k init, 0k highmem)
    virtual kernel memory layout:
    fixmap : 0xffee8000 - 0xfffff000 (1116 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
    lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
    .init : 0xc03f3000 - 0xc043b000 ( 288 kB)
    .data : 0xc0319f76 - 0xc03ed360 ( 844 kB)
    .text : 0xc0100000 - 0xc0319f76 (2151 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    CPA: page pool initialized 1 of 1 pages preallocated
    SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    Calibrating delay loop (skipped), value calculated using timer frequency.. 1395.93 BogoMIPS (lpj=2324696)
    Security Framework initialized
    Mount-cache hash table entries: 512
    CPU: L1 I cache: 16K, L1 D cache: 16K
    CPU: L2 cache: 256K
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    Freeing SMP alternatives: 9k freed
    ACPI: Core revision 20080609
    ACPI: Checking initramfs for custom DSDT
    ACPI: setting ELCR to 0200 (from 0e00)
    weird, boot CPU (#0) not listedby the BIOS.
    SMP motherboard not detected.
    Local APIC not detected. Using dummy APIC emulation.
    SMP disabled
    Brought up 1 CPUs
    Total of 1 processors activated (1395.93 BogoMIPS).
    net_namespace: 832 bytes
    Booting paravirtualized kernel on bare hardware
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
    PCI: Using configuration type 1 for base access
    ACPI: EC: Look up EC in DSDT
    ACPI: EC: non-query interrupt received, switching to interrupt mode
    ACPI: Interpreter enabled
    ACPI: (supports S0 S1 S3 S4 S5)
    ACPI: Using PIC for interrupt routing
    ACPI: EC: GPE = 0x9, I/O: command/status = 0x66, data = 0x62
    ACPI: EC: driver started in interrupt mode
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: 0000:00:00.0 reg 10 32bit mmio: [f4000000, f7ffffff]
    PCI: 0000:00:02.0 reg 10 32bit mmio: [50000000, 50000fff]
    pci 0000:00:02.0: supports D1
    pci 0000:00:02.0: supports D2
    pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:02.0: PME# disabled
    PCI: 0000:00:02.1 reg 10 32bit mmio: [50100000, 50100fff]
    pci 0000:00:02.1: supports D1
    pci 0000:00:02.1: supports D2
    pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:02.1: PME# disabled
    PCI: 0000:00:03.0 reg 10 32bit mmio: [f0120000, f0120fff]
    PCI: 0000:00:03.0 reg 14 io port: [1800, 183f]
    PCI: 0000:00:03.0 reg 18 32bit mmio: [f0100000, f011ffff]
    PCI: 0000:00:03.0 reg 30 32bit mmio: [0, fffff]
    pci 0000:00:03.0: supports D1
    pci 0000:00:03.0: supports D2
    pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:03.0: PME# disabled
    PCI: 0000:00:03.1 reg 10 io port: [1840, 1847]
    PCI: 0000:00:03.1 reg 14 32bit mmio: [f0121000, f0121fff]
    pci 0000:00:03.1: supports D1
    pci 0000:00:03.1: supports D2
    pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:03.1: PME# disabled
    PCI: 0000:00:05.0 reg 10 32bit mmio: [f0122000, f0122fff]
    PCI: 0000:00:05.0 reg 14 32bit mmio: [f0000000, f00fffff]
    pci 0000:00:05.0: supports D1
    pci 0000:00:05.0: supports D2
    PCI: 0000:00:07.1 reg 20 io port: [1850, 185f]
    PCI: 0000:00:07.2 reg 20 io port: [1860, 187f]
    pci 0000:00:07.3: quirk: region 1000-103f claimed by PIIX4 ACPI
    pci 0000:00:07.3: quirk: region 1040-104f claimed by PIIX4 SMB
    pci 0000:00:07.3: PIIX4 devres C PIO at 15e8-15ef
    pci 0000:00:07.3: PIIX4 devres I PIO at 03f0-03f7
    pci 0000:00:07.3: PIIX4 devres J PIO at 002e-002f
    PCI: 0000:01:00.0 reg 10 32bit mmio: [f8000000, fbffffff]
    PCI: 0000:01:00.0 reg 14 io port: [2000, 20ff]
    PCI: 0000:01:00.0 reg 18 32bit mmio: [f0200000, f0203fff]
    PCI: 0000:01:00.0 reg 30 32bit mmio: [0, 1ffff]
    pci 0000:01:00.0: supports D1
    pci 0000:01:00.0: supports D2
    PCI: bridge 0000:00:01.0 io port: [2000, 2fff]
    PCI: bridge 0000:00:01.0 32bit mmio: [f0200000, f02fffff]
    PCI: bridge 0000:00:01.0 32bit mmio pref: [f8000000, fbffffff]
    bus 00 -> node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11)
    ACPI: Power Resource [PSER] (off)
    ACPI: Power Resource [PSIO] (on)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp 00:00: mem resource (0x0-0x9ffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc0000-0xc3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc4000-0xc7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xc8000-0xcbfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xcc000-0xcffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd0000-0xd3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd4000-0xd3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xd8000-0xd7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xdc000-0xdbfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe0000-0xe3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe4000-0xe7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xe8000-0xebfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xec000-0xeffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp 00:00: mem resource (0xf0000-0xfffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
    pnp: PnP ACPI: found 15 devices
    ACPI: ACPI bus type pnp unregistered
    PCI: Using ACPI for IRQ routing
    PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
    PCI: setting IRQ 9 as level-triggered
    pci 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
    pci 0000:00:02.1: PCI INT B -> Link[LNKB] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    pci 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    pci 0000:00:03.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    pci 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
    PCI: setting IRQ 10 as level-triggered
    pci 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10
    pci 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    ACPI: RTC can wake from S4
    system 00:00: iomem range 0x100000-0x1fffffff could not be reserved
    system 00:00: iomem range 0xfff80000-0xffffffff could not be reserved
    system 00:02: ioport range 0x1000-0x103f has been reserved
    system 00:02: ioport range 0x1040-0x104f has been reserved
    system 00:02: ioport range 0xfe00-0xfe0f has been reserved
    system 00:09: ioport range 0x15e0-0x15ef has been reserved
    pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
    pci 0000:00:01.0: IO window: 0x2000-0x2fff
    pci 0000:00:01.0: MEM window: 0xf0200000-0xf02fffff
    pci 0000:00:01.0: PREFETCH window: 0x000000f8000000-0x000000fbffffff
    pci 0000:00:02.0: CardBus bridge, secondary bus 0000:02
    pci 0000:00:02.0: IO window: 0x001400-0x0014ff
    pci 0000:00:02.0: IO window: 0x001c00-0x001cff
    pci 0000:00:02.0: PREFETCH window: 0x30000000-0x33ffffff
    pci 0000:00:02.0: MEM window: 0x34000000-0x37ffffff
    pci 0000:00:02.1: CardBus bridge, secondary bus 0000:06
    pci 0000:00:02.1: IO window: 0x003000-0x0030ff
    pci 0000:00:02.1: IO window: 0x003400-0x0034ff
    pci 0000:00:02.1: PREFETCH window: 0x38000000-0x3bffffff
    pci 0000:00:02.1: MEM window: 0x3c000000-0x3fffffff
    pci 0000:00:02.0: power state changed by ACPI to D0
    pci 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    pci 0000:00:02.1: power state changed by ACPI to D0
    pci 0000:00:02.1: PCI INT B -> Link[LNKB] -> GSI 9 (level, low) -> IRQ 9
    bus: 00 index 0 io port: [0, ffff]
    bus: 00 index 1 mmio: [0, ffffffff]
    bus: 01 index 0 io port: [2000, 2fff]
    bus: 01 index 1 mmio: [f0200000, f02fffff]
    bus: 01 index 2 mmio: [f8000000, fbffffff]
    bus: 01 index 3 mmio: [0, 0]
    bus: 02 index 0 io port: [1400, 14ff]
    bus: 02 index 1 io port: [1c00, 1cff]
    bus: 02 index 2 mmio: [30000000, 33ffffff]
    bus: 02 index 3 mmio: [34000000, 37ffffff]
    bus: 06 index 0 io port: [3000, 30ff]
    bus: 06 index 1 io port: [3400, 34ff]
    bus: 06 index 2 mmio: [38000000, 3bffffff]
    bus: 06 index 3 mmio: [3c000000, 3fffffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    TCP: Hash tables configured (established 16384 bind 16384)
    TCP reno registered
    NET: Registered protocol family 1
    Unpacking initramfs... done
    Freeing initrd memory: 714k freed
    Simple Boot Flag at 0x35 set to 0x1
    IBM machine detected. Enabling interrupts during APM calls.
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    apm: overridden by ACPI.
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    msgmni has been set to 1006
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:00:00.0: Limiting direct PCI/PCI transfers
    pci 0000:00:03.0: Firmware left e100 interrupts enabled; disabling
    pci 0000:01:00.0: Boot video device
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver4 ports, IRQ sharing disabled
    serial 00:0c: activated
    00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    serial 0000:00:03.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    input: Macintosh mouse button emulation as /class/input/input0
    PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP cubic registered
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    registered taskstats version 1
    Freeing unused kernel memory: 288k freed
    Switched to high resolution mode on CPU 0
    input: AT Translated Set 2 keyboard as /class/input/input1
    ACPI: ACPI Dock Station Driver
    SCSI subsystem initialized
    libata version 3.00 loaded.
    ata_piix 0000:00:07.1: version 2.12
    scsi0 : ata_piix
    scsi1 : ata_piix
    ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x1850 irq 14
    ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1858 irq 15
    ata1.00: ATA-6: TOSHIBA MK1032GAX, AB211A, max UDMA/100
    ata1.00: 195371568 sectors, multi 16: LBA48
    ata1.00: configured for UDMA/33
    ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-T20L, NR02, max UDMA/33
    ata2.00: configured for UDMA/33
    scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1032GA AB21 PQ: 0 ANSI: 5
    scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20L NR02 PQ: 0 ANSI: 5
    Driver 'sd' needs updating - please use bus_type methods
    sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda: sda1 sda2 sda3 sda4
    Driver 'sr' needs updating - please use bus_type methods
    sd 0:0:0:0: [sda] Attached SCSI disk
    sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 1:0:0:0: Attached scsi CD-ROM sr0
    ReiserFS: sda2: found reiserfs format "3.6" with standard journal
    ReiserFS: sda2: using ordered data mode
    ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: sda2: checking transaction log (sda2)
    ReiserFS: sda2: Using r5 hash to sort names
    rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month, y3k
    Non-volatile memory driver v1.2
    thinkpad_acpi: ThinkPad ACPI Extras v0.21
    thinkpad_acpi: http://ibm-acpi.sf.net/
    thinkpad_acpi: ThinkPad BIOS 13ET14WW (1.00c), EC unknown
    Registered led device: tpacpi::thinklight
    thinkpad_acpi: another device driver is already handling bay events
    thinkpad_acpi: disabling subdriver bay
    Registered led device: tpacpi::power
    Registered led device: tpacpi:orange:batt
    Registered led device: tpacpi:green:batt
    Registered led device: tpacpi::dock_active
    Registered led device: tpacpi::bay_active
    Registered led device: tpacpi::dock_batt
    Registered led device: tpacpi::unknown_led
    Registered led device: tpacpi::standby
    input: ThinkPad Extra Buttons as /class/input/input2
    e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
    e100: Copyright(c) 1999-2006 Intel Corporation
    e100 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
    e100 0000:00:03.0: PME# disabled
    e100: eth0: e100_probe: addr 0xf0120000, irq 11, MAC addr 00:03:47:0f:de:3d
    eepro100.c:v1.09j-t 9/29/99 Donald Becker
    eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[email protected]> and others
    Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    gameport: CS46xx Gameport is pci0000:00:05.0/gameport0, speed 1864kHz
    Linux agpgart interface v0.103
    agpgart-intel 0000:00:00.0: Intel 440BX Chipset
    agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf4000000
    [drm] Initialized drm 1.1.0 20060810
    pci 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    [drm] Initialized r128 2.5.0 20030725 on minor 0
    ath_hal: module license 'Proprietary' taints kernel.
    AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
    fuse init (API version 7.9)
    Marking TSC unstable due to cpufreq changes
    ACPI: AC Adapter [AC] (on-line)
    ACPI: Battery Slot [BAT0] (battery present)
    input: Power Button (FF) as /class/input/input3
    ACPI: Power Button (FF) [PWRF]
    input: Lid Switch as /class/input/input4
    ACPI: Lid Switch [LID]
    input: Sleep Button (CM) as /class/input/input5
    ACPI: Sleep Button (CM) [SLPB]
    Clocksource tsc unstable (delta = 142862504 ns)
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    processor ACPI0007:00: registered as cooling_device0
    ACPI: Processor [CPU] (supports 8 throttling states)
    thermal LNXTHERM:01: registered as thermal_zone0
    ACPI: Thermal Zone [THM0] (34 C)
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sr 1:0:0:0: Attached scsi generic sg1 type 5
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    Yenta: CardBus bridge found at 0000:00:02.0 [1014:0130]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:00:02.0, mfunc 0x00001000, devctl 0x66
    spurious 8259A interrupt: IRQ7.
    Yenta: ISA IRQ mask 0x00b8, PCI irq 9
    Socket status: 30000020
    Yenta: CardBus bridge found at 0000:00:02.1 [1014:0130]
    Yenta: Using INTVAL to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta TI: socket 0000:00:02.1, mfunc 0x00001000, devctl 0x66
    Yenta: ISA IRQ mask 0x00b8, PCI irq 9
    Socket status: 30000006
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    pccard: CardBus card inserted into slot 0
    PCI: 0000:02:00.0 reg 10 32bit mmio: [0, ffff]
    ath_pci 0000:02:00.0: enabling device (0000 -> 0002)
    ath_pci 0000:02:00.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    input: PC Speaker as /class/input/input6
    USB Universal Host Controller Interface driver v3.0
    uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10
    uhci_hcd 0000:00:07.2: UHCI Host Controller
    uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:07.2: irq 10, io base 0x00001860
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    piix4_smbus 0000:00:07.3: IBM system detected; this module may corrupt your serial eeprom! Refusing to load module!
    piix4_smbus: probe of 0000:00:07.3 failed with error -1
    Error: Driver 'pcspkr' is already registered, aborting...
    usb 1-1: new low speed USB device using uhci_hcd and address 2
    input: Video Bus as /class/input/input7
    usb 1-1: configuration #1 chosen from 1 choice
    ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
    IBM TrackPoint firmware: 0x0e, buttons: 3/3
    input: TPPS/2 IBM TrackPoint as /class/input/input8
    NET: Registered protocol family 23
    parport_pc 00:0d: activated
    parport_pc 00:0d: reported by Plug and Play ACPI
    parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
    nsc-ircc 00:0e: activated
    nsc-ircc, chip->init
    nsc-ircc, Found chip at base=0x02e
    nsc-ircc, driver loaded (Dag Brattli)
    IrDA: Registered device irda0
    nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500
    PPP generic driver version 2.4.2
    MadWifi: ath_attach: Switching rfkill capability off.
    wifi0: Atheros AR2413 chip found (MAC 7.8, PHY 2112A 4.5, Radio 5.6)
    lp0: using parport0 (interrupt-driven).
    ath_pci: wifi0: Atheros 5212: mem=0x34000000, irq=9
    ppdev: user-space parallel port driver
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0xc00-0xcf7: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    usbcore: registered new interface driver hiddev
    input: Logitech Logitech USB Optical Mouse as /class/input/input9
    input,hidraw0: USB HID v1.11 Mouse [Logitech Logitech USB Optical Mouse] on usb-0000:00:07.2-1
    usbcore: registered new interface driver usbhid
    usbhid: v2.6:USB HID core driver
    JFS: nTxBlock = 4026, nTxLock = 32211
    Adding 1100444k swap on /dev/sda4. Priority:-1 extents:1 across:1100444k
    warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
    conservative governor failed, too long transition latency of HW, fallback to performance governor
    thinkpad_acpi: requested hot key mask 0x0000ffff, forced to 0x00008000 (NVRAM poll mask is 0x00fb8000): no firmware mask support
    The strangest thing has also happened recently. The laptop refuses to use its own display when starting up in the dock unless an external monitor is plugged in. If a CRT is plugged in, the docked laptop starts up and shows the splash screen on its LCD. If no CRT is plugged in, turning on the docked laptop results in a blank screen. This might have happened because I fiddled with the BIOS which would make alot of sense but resetting the BIOS to default configuration hasn't fixed the problem. I also could have broken a pin but the last thing I remember doing before this happened is running cat /sys/module/snd_ac97_codec/parameters/power_save. It's one of those untouchable virtual files that causes a kernel oops when I try to read it sometimes. I have no idea how this would break the dock but it doesn't matter. Even if using the dock requires some external monitor jazz, I still want the card to be detected and it isn't.
    Sorry to bombard you with obscure information but I don't know where else to turn. I've asked on the thinkpad mailing list and IRC channel to no response and I've seen one other "knowledgeable person" mention these errors on the LKML. I will subscribe to that and ask him too. I'm just very surprised... this gave me the impression that what I wanted to do would work trivially and automatically on Linux and now I'm finding that it's broken for me and possibly every other Linux user. I will seek out thinkpad users from around here with all types of models and distros and see if they have any luck. So far Arch, Arch install CD and an ancient Ubuntu install CD don't work here. If anyone has this and can test it or can decipher some ideas from the posted output (new kernel parameters, new kernel config flags, new udev rules, new modules?) I'd really appreciate it.

  • Tells me i can't use cover flow?

    hello,
    i just reinstalled windows xp home on my computer, itunes gives me the "itunes is unable to browse album covers on this computer"
    my specs are the following:
    windows xp home sp3
    latest directX
    updated drivers (i think, windows was having a problem with updates)
    700mhz ibm thinkpad a22m (2628) 512mb of ram 40gb hdd, i think ati rage M1
    it works perfectly on my ibook g3 500 and imac g3 500 which are both obviously half of this thinkpad.
    it worked before the windows reinstallation.

    Start menu -> Control panel - Add/remove programs.
    Select QuickTime and run Repair.

  • Unable to install volume controls / battery status software on A22m

    I have a rather old ThinkPad - a A22m 2628-TSU - that I just recently reformated and installed with Windows XP.
    I'm now trying to install the software that'll let you adjust the volume with the volume buttons and that'll show the batteries status and am having some difficulty doing so.  I would have thought that Keyboard Customizer Utility for Windows 2000, XP - ThinkPad and ThinkPad Power Management driver for Windows Vista, XP, 2000, Me, 98 SE - ThinkPad would have done the trick, but alas, it appears that they do not.  I ran the *.exe that I downloaded, which created a C:\DRIVERS directory, and I then ran the setup files within each of the newely created directories, but that didn't help.  So what will help?
    Also, unrelated to this...  whenever I try to visit lenovo.com, in Firefox, on that computer, the computer freezes.  It doesn't do this in Internet Explorer and lenovo.com is the only page I've found that causes this problem in Firefox (well, the whole computer freezes, but it only happens while I'm using Firefox).  I know this is a short in the dark, but...  any ideas?

    You need to install the Hot Key driver from the system utilities file matrix. (You may also need the on screen display utility also?) 
    re. the firefox, sorry I don't use it.
    Message Edited by andyP on 12-24-2007 09:59 PM
    Andy  ______________________________________
    Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
    Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
      Deutsche Community     Comunidad en Español    English Community Русскоязычное Сообщество
    PepperonI blog 

  • 2 problems, video drivers, and cpu underclocked a22m

    hi, I have an a22m 2628-RSU, first off, whatever OS I install the cpu runs at 697mhz, the bios says it is an 850mhz (the cpu it self says 850/256 meaning 850mhz 256k cache) I even replaced the CPU with an identical one, and still 697mhz.
    the bios has the cpu set to performance not battery life. I have the same problem with an a21m which is a 700mhz, but only runs at 547mhz.
    problem 2, I have installed windows 7 RC (7100) everything works great except it does not like the video card, same happend with vista. It says drivers are installed, but I know they are not functioning. 3d screen savers like the 3d text which work flawlessly in windows xp, tell me that my video card does not support them, in both windows vista, and 7.
    thank you in advanced for any help.
    IBM Thinkpad a22m, 850mhz (697mhz) 512mb of ram, 120gb HDD, dual boot windows xp pro, and windows 7 RC (7100)
    IBM Thinkpad a21m 700mhz (547mhz) 384mb 40gb, Windows XP

    Welcome to the forum!
    You have to push the machine pretty hard (open 10 Firefox windows and run Photoshop at the same time) to get the CPU to work at maximum speed. That is one of the ideas behind Intel's SpeedStep that your A22m has.
    Graphic cards as old as yours are not supported by Vista or W7. 
    Hope this helps.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • A22m with windows 7

    Hello, I know what your thinking, but it actually runs better windows xp, except for one thing, the display drivers.
    same thing happens in vista. the drivers install successfully, but in device manager I get this error: Windows has stopped this device because it has reported problems. (Code 43)
    people told me its because the video card is "too old" it works in XP, and can handle direct 3D with directX 9, it has no reason not to work. has ANYONE gotten this card to work in either windows vista or windows 7?
    its an a22m 2628-RSU
    OS: Windows 7 RC (7100)
    Thank you in advanced, Joey 
    IBM Thinkpad a22m, 850mhz (697mhz) 512mb of ram, 120gb HDD, dual boot windows xp pro, and windows 7 RC (7100)
    IBM Thinkpad a21m 700mhz (547mhz) 384mb 40gb, Windows XP

    There is no support for ThinkPads that old for either Vista or W7 when it comes to graphics.
    Try using the XP driver.
    Good luck.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • No sound X31

    I don't have any sound when viewing Youtube on IE or Firefox. I think it disappeared after a windows xp update (before the Microsoft cut-off date). I still get beeps from the X31 Thinkpad though, just no sound with Youtube or XP on start up for example. By the way Youtube is lagging too since the win xp update -it wasn't before though. I updated all the drivers for the X31 from your Lenovo site but to no avail. I have the latest Flash installed. Installed Shockwave too Direct X installed - didn't make a difference I think its something to do with the windows xp update cause after that my Thinkpad got stuffed up, Youtube slowed and Soundmax drivers kept disappearing and reappearing. I tried the regedit trick for audio whereby you trick windows into thinking it's service pack 2 (I'm on service pack 3, XP). Also checked Device Manager under audio, no ! marks beside the audio. I tried CCleaner as well. I disabled the video accelerator under settings in Youtube video as well I don't have many 3rd party programs installed on the Thinkpad eg no iTunes, no Skype either. Thanks in advance
    Solved!
    Go to Solution.

    Service pack 3 included the HDA drivers.  Did you change the registry back from trying to fool the system into thinking you had Service Pack 2?  
    What is exactly listed under Sound, video and game controllers in Control Panel?
    In C: there should be a folder labeled Drivers.  There should be a folder in there called Audio.  In there, there should be an icon for Install.  See if you can install it from there.
    You might want to check and see if you are set to automatically install all updates from Windows Update.  If you are, Windows might be installing a later driver that might not be  working quite right.  I wouldn't let Windows automatically install optional updates.   
    Another thing you could do if you haven't already tried it is install TVSU and run it and see what it comes up with.  You'll need an up to date net.framework installed to run it.  If there is a bios available, that could fix it.  I usually don't recommend updating the bios just because bios updates can be a little dangerous  to do, but in this case it might just fix it if there is one available.    
    I have an X32 running the preload that I'm checking out your problem with and it's set up pretty much the same as yours.  We should be able to figure this out.
    Regards,
    Dave
    T430u, x301, x200T, x61T, x61, x32, x41T, x40, U160, ThinkPad Tablet 1838-22R, Z500 touch, Yoga Tab 2 Windows 8.1, Yoga Tablet 3 Pro
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
    If someone helped you today, pay it forward. Help Someone Else!
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • G580 Poor Sound

    Hi
    I just installed an application caled camtasia on my g580, which is is video making tool. I done a few tests of the sound playback of my recording and the sound is really hissy and muffled like speaking into a cup. I tried increasing the system sound and lowering the microphone sound, which helped a little bit but not much. I still get the hissing interference sound in the background.
    I used camtasia on my old XP HP laptop and never had this problem.
    Any thoughts on proper sound settings I can use or changes I can make to fix this?
    Thanks
    Andrew

    No it is the same both headset on and when unplugged.
    I have two microhpone devices listed in the properties. The default one says manufacturer is Microsoft so I am guessing that it is the built in microphone. If I mute the microphone and try speaking with my headphones on then nothing gets recorded, same with if I remove my microphone headset.
    I take it if you plug in a mic then this is what directs the sound through the system but the main microphone is still the default device?
    Also wondering why I do not have realtek showing up anywhere. I have realtek folder in my program files. Seen a thread here where no sound problem was fixed by doing some tweaking in realtek advanced control panel wherever that is:
    http://forums.lenovo.com/t5/X-Series-ThinkPad-Laptops/X230-No-Sound-Until-I-Go-To-Settings-To-Play-S...

  • Cannot map sound through it from another system?

    I have two systems, the mac mini and a thinkpad notebook. I initially setup the mac speaker output to go to the input on my thinkpad dock, worked like a charm, I could hear both the sounds on the mac (itunes for instance) while still being able to hear sounds on my thinkpad when I'm working through the same speakers.
    I just tried this in reverse as the family would like the mac to have sound when I'm out of the house with my laptop. It doesn't work.
    When I am looking at the input for sound on the mac and I play a sound on the thinkpad the mac KNOWS the sound is being played, the input level shows it, but it just will not actually play it through the speakers.
    What am I missing here? Sound does play from the mac through the speakers though.

    Well, this worked and didn't work. It did pass sound through, but it always had an annoying "buzz" in the speakers, like a mic hooked up to an amp etc. Also, the sound wasn't clean and crisp, was kind of choppy I guess...Tried it even at the lowest levels I could set everything to, the buzz was always there and the sound just wasn't quite right.
    Thanks for the suggestion though!
    It's just too bad a mac can't do this natively and clean like my thinkpad does...on the thinkpad no buzz and sound is clear as a bell...Guess the family will just have to get use to plugging the speakers into the mac when I've taken my laptop with me and left for the day.

Maybe you are looking for

  • Issue while creating a field at header level in CRM 4.0

    Hi, Using transaction EEWB, I tried to add a custom field at the header level to an existing Project. The Project already had an extension created to which I made the modifications i.e. added the field at header level. But, when I tried to generate t

  • JTree background color. How to...?

    I have set the background color of Jtree to pink and have used setOpaque(true). Now when ever I click on a node the node's color is not changing to the default blue color. How to change it?

  • Which is the correct Camera Raw Plugin

    Hi, I have been scouring your website to find the correct camera raw plugin for lightoom and my 50D. I seem to be going around in circles and am beginning to become a bit frustrated. Can you please help me?

  • Integration within SAP HR

    Hi Group, I wanted detailed Intergration within SAP HR. Can any body send to [email protected] Regs, Brahma

  • Bluetooth 4.0 on my mid 2010 iMac?

    Hiya, I'd like to start using a bluetooth foot pedal (IK Blueboard) to control amplitube on my mac but it needs bluetooth 4.0 to connect which my apparently aging mid 2010 iMac doesn't have. Does anyone know of any mac compatible usb Bluetooth 4.0 do