Thinkpad Port Replicator II USB Port

I have a T30 laptop that had problems with the USB ports. so I turned them off.  I got a port replicator which has a USB port, but it does not seem to work either.  Is there any way to get the USB port on the replicator to work without turning on the USB ports on the laptop itself?

I considered a PCMCIA card, but I don't think I can use that card while also using a card for my wireless connection (not enough room).  This replicator seemed to be the best solution, since in addition to having a USB port, it also allows me to attach a separate keyboard and mouse.  There must be a way to turn off the USB ports on the laptop itself while allowing the port on the replicator to work.

Similar Messages

  • Thinkpad W530 Yellow (Rear) USB port stopped working

    I have had my W530 for about 3 month and the rear yellow USB port just stopped working a few days ago. I have recovered the whole system to factory status and updated the BIOS but the USB port is still not working. I tried several devices, it seems like that the USB has no power at all. The LED on the flash drives do not come on when I plug it in. All the other USB ports are working. Has anyone encountered the same problem before? Any help is appreciated.

    Hi all,
    The yellow USB port of my W530 stopped working suddenly today. It can charge but cant recognize any devices. The other devices work well. I have tried many ways like updating the bios, setting the bios to defaults... still not working.
    seems that its a big issue 
    Any ideas? Thank you!
    Moderator Note; subject edited; post merged in. Link to this thread removed.

  • How to Install a parallel port printer to usb port of Pavilion dv5 Notebook

    In trying to install my HP DeskJet 610C Parallel Port printer to my HP Pavilion dv5-1235dx Notebook PC with Windows Vista Home Premium 64-bit, I followed instructions given by HP Support some two years back.
    I connected up the two units through a Parallel-to-USB ports cable. The PC loaded and confirmed suitable driver. (Following advice from sites on the Internet, I have made repeated attempts to carefully install the printer, but to no avail).
    Upon my issuing the Print instruction, the printer invariably prints two copies of what appears to be 'gibberish' in two lines at the start of the sheet. Thereafter it picks up and then ejects 6-8 sheets of blank paper.
    Any help in resolving this anomalous situation will be be most welcome and much appreciated.
    I might add that the printer works normally when connected in parallel to an older, Compaq Armada 1750 Notebook (XP OS). In this instance too, the Parrallel/USB worked as in the Pavilion PC, above.  
    This question was solved.
    View Solution.

    Hi khalidem, 
    Sounds like you have a communication problem with the printer cables. Have you tried a new parallel to USB cable or adapter?
    I am an HP employee.
    Say Thanks by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"

  • Firefox does not paint the window if Windows 7 Basic theme is selected and Fujitsu USB port replicator PR07 is used

    If I use "Windows 7 Basic" theme on my laptop (Fujitsu Lifebook A532), the Firefox window is not painted.
    I see only the border of the window, the content not. As soon as I switch back to the "Windows 7" theme,
    it works again.
    It could be related to the graphics driver (from Intel) of my new laptop.
    Before I had a desktop computer, and did not have this problem.
    Update: the problem occurs only if I use my port replicator (Fujitsu USB Port Replicator PR07).
    If I unplug the replicator, and use only the monitor of my laptop, everything is fine.

    ''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''Please create a screenshot of the problem you're seeing by following the guide mentioned at [[How do I create a screenshot of my problem?]].
    Once you've done this, attach the saved screenshot file to your forum post by clicking the '''Browse...''' button below the ''Post your reply'' box. This will help us to visualize the problem.

  • ThinkPad USB Port Replicator with Digital Video (M01060) drivers for Windows 8 RTM

    Hello,
    I have a X301 with the port replicator (M01060) running Windows 8 RTM build. I tried installing the Windows 7 drivers with no luck. The screens will flicker and I also getting blue screen crashes. I had to uninstall the drivers but I can only use the port replicator as usb hub.
    Any workaround to this issue? I have 2 external monitors I use for work plus the laptop one as third.
    Thanks for your help.
    Marcelo

    I have the exact same problem on my W510. Everything but the screen Works. I cannot however do duplicate screens. That would help a Little bit, so I could use the big monitor instead of just the laptop.
    Please fix this Lenovo!

  • Port Replicator III+ very high cpu when moving usb mouse only in W2k

    Tecra M2 with a port replicator III+
    It's set to dual boot into XP and Win2000 (yes I know it's getting on a bit, but I've got a lot of stuff installed in win2k that is difficult to get hold of these days).
    XP is 100% fine, but with win 2000 if I use my *USB mouse* on the *port replicator* ports and waggle the mouse around - the *CPU* jumps from 0 to *70+%* usage (the system process which I think indicatates as IRQ problem). If I plug the mouse into the laptop ports (when the laptop is docked) - it's fine, at most 5% cpu usage. It's a basic microsoft mouse. I definately think it's a usb problem of some kind, because the cpu even jumps a bit if I type quickly on my usb keyboard (only a couple of %). It happens with all the replicator's usb ports.
    Any ideas? I don't really want to plug in my mouse in the morning because it kinda defeats the point of having a docking station in the first place! I've got the mobile extensions installed. All the other aspects of the replicator are fine
    Martin

    Huh it will not be easy to find good explanation for this.
    At this time when Tecra M2 was offered on the market as compatible port replicator Toshiba has offered Toshiba Advanced Port Replicator III (not +) and at this time both supported operating system was tested with it.
    Later Toshiba has designed Toshiba Advanced Port Replicator III+ and confirmed compatibility with Tecra M2 but obviously with newer (at this time) WXP.
    So now you have follow situation: you use newer port replicator but with much older operating system so I presume there is maybe some compatibility problem with W2K.
    I cannot imagine you use it so often with W2K and if yes it cannot be so problematic to connect mouse directly on notebooks USB port.
    Sorry but I dont think there is anything you can do about it.

  • External USB2 drive doesn't work on left USB port

    Hi,
    I have an 2,5" external usb hard drive which works on my right usb port, but not on my left one, when i try the disk on the left port, afterwards the usb port is dead untill restart, even my mighty mouse does'nt work on it. My logic board and board with audio and left usb port are already replaced, without result, also the cable beween logic board and daughter board...
    The disk works on a colleage's macbook pro on both ports...
    what to do?

    Try resetting the PRAM:
    http://docs.info.apple.com/article.html?artnum=2238
    Make sure also that no USB devices are connected when you put the machine to sleep (close the lid, or start energy saver).
    A restart will clear a hung USB port usually.

  • Port replicator for P200 series?

    Hello, what kind of port replicator should I buy to work with a P200-RT9 series laptop?

    Hello
    Nick is absolutely right. It can not be connected to port replicator. All units that can be connected to port replicator have expansion port at the bottom side.
    Bye

  • Port replicator for Equium A60

    i want to use a port replicator for a A60 equium laptop can anyone advise what to use as i cannot see one listed for this laptop

    Hello
    Nick is absolutely right. It can not be connected to port replicator. All units that can be connected to port replicator have expansion port at the bottom side.
    Bye

  • How can I play itunes music through one of the usb ports on my new MacBook Air?

    Greetings Everyone.
      I just purchased my first Mac product I want to be able to play music from the itunes app from one of my usb ports to the usb port on the front panel of my Yamaha CD changer. I want to utilize the buit-in DAC of the Yamaha. A friend was able to run his Ipad through it but I can't see a way to run my MacBook Air through it. When I go to System Preferences -> Hardware -> Sound the only item listed for Output is "Internal Speakers".
    Any ideas? Thanks in advance.

    Reset the SMC and PRAM
    SMC Reset:
    Shut down the MacBook Pro.
    Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
    On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
    Release all the keys and the power button at the same time.
    Press the power button to turn on the computer. 
    PRAM:
    Shut down the MacBook Pro.
    Locate the following keys on the keyboard: Command, Option, P, and R.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.

  • MBP will not boot when a USB/USB2 Device is plugged into either USB port.

    MBP hangs on the initial Gray Screen when anything is plugged into either of my MBP's USB ports on boot and reboot. I've tried it with a USB mouse, USB2 Hard Drive, USB Memory Stick and USB RF Mouse. It DOES NOT happen when anything is plugged into the Firewire 800 port, only either USB port.
    It happens on reboot and a fresh start whenever something is plugged into either of these two USB ports. I've let the gray screen sit overnight, just to see if it would enter the Login Panel. Didn't happen.
    As soon as I unplug the USB item, the HD whirls up and a few seconds later the booting continues as normal. I have booted in verbose mode just to see what the system says. It stays on the gray screen, again, until I unplug the USB device. However, the screen does note the following:
    "The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 3 of hub @ location: 0x6000000)."
    The above error may or may not be related.
    ........AND BEFORE ANYONE SUGGESTS IT, YES I HAVE ZAPPED THE PRAM and reinstalled the OS from new MBP Install Disks from scratch! Still occurs.
    Hope someone can also validate what I've wrote with the newer MBP, as well.
    Many Thanks!

    JKosh wrote:
    MBP hangs on the initial Gray Screen when anything is plugged into either of my MBP's USB ports on boot and reboot. I've tried it with a USB mouse, USB2 Hard Drive, USB Memory Stick and USB RF Mouse. It DOES NOT happen when anything is plugged into the Firewire 800 port, only either USB port.
    It happens on reboot and a fresh start whenever something is plugged into either of these two USB ports. I've let the gray screen sit overnight, just to see if it would enter the Login Panel. Didn't happen.
    As soon as I unplug the USB item, the HD whirls up and a few seconds later the booting continues as normal. I have booted in verbose mode just to see what the system says. It stays on the gray screen, again, until I unplug the USB device. However, the screen does note the following:
    I'm having exactly the same problem with my MacBook Pro.
    It's either the usb hub or simply the iphone... every time I need to boot my macbook pro I have to disconnect every device. It's getting quite annoying.
    The previous 17" Powerbook G4 had no issues.

  • USB Port on Keyboard

    I remember reading somewhere that there is a limitation as to what you can plug into the USB port on the Apple keyboard that comes with the iMac. Can anyone confirm this? Is the keyboard USB port USB2? Can I use a memory card reader in this port?
    Thanks

    Keyboard USB ports are low-power USB 1.1. USB 2.0 devices may work, but at 1.1 speeds. Devices that tend not to work are those that need to be powered from the USB port; whether a memory card reader would work I can't say not having tried one.

  • HT5868 My iphone 5 with ios 7 stopped promting me to "trust this computer" and wont charge from USB ports now

    My iphone 5 with ios 7 stopped promting me to "trust this computer" 1 day ago after doing it everytime i plugged it in to a USB port on my work laptop. It will now no longer charge from any of the USB ports. The USB ports work fine on the laptop for other devices and my phone will prompt me and charge at any other computer in my office. I possibly hit do not trust by accident which may have caused this. I reset all settings on the phone and rebooted my laptop and none of this fixed the issue. Phone syncs and charges fine at home and there were no issues with my work laptop up until 2 days ago with prompts or charging. Any ideas??

    Hi,
    I'm new on this forum and with my iphone 5c.
    'Till some days ago I had a Windows Vista pc and when I connected the iphone, it was recognized.
    Yesterday I decided to change my SO in Linux Ubuntu 13.04 but now my iphone isn't recognized and I'm not able to use it.
    This message appears on my iphone
    "Trust This Computer? Your settings and data will be accessible from this computer when connected via USB or Wi-Fi. [Trust] [Don't Trust]"
    I clicked Trust but the iphone buzzes twice, then repeats the prompt. This will repeat endlessly.
    I read a lot about the bug, but is there any solutions waiting for the resolution of bug?
    I can't use my iphone!!!!

  • K450 USB Ports and Card Readers not working

    When I plug in devices to my K450 ideacentre desktop USB ports, they are not recognized.  The same for a couple of memory cards I have tried in the card reader.  These are all working fine when put in other computers.  The card reader and USB ports do work when I insert a multi card reader into the USB port or a multi USB port into the USB port (and then use either of those to read the same external hard drive or memory cards that don't show up when installed directly).  Any idea what this could be?  I'm sure it's something simple that I'm missing but I can't figure it out.  I'm running Windows 8.  Thanks for any help!

    I wanted to add to this...I did plug in a CF card the other day and that was recognized.  I then tried my external hard drive directly again in a front USB port and it worked for a while (an hour or so).  Then it suddenly was not there anymore as if I'd ejected it even though I didn't.  Tried to put it back in and nothing.  This tells me it may be a hardware problem since it "recognized" it for a bit.  It's very frustrating.

  • USB port dies then lives again

    MacBook Pro 17" 3,1 plugged in to AC. Mouse connected to right USB port. Mouse/USB port dies. I unplug it, then plug it back in, and works again. This occurs about once every 15-30 minutes or so. It's a clear mouse and you can see the little laser inside doing its thing. The laser goes dim occassionally, as if it's not drawing enough power.
    It's only a mouse and the computer is plugged in, so it seems strange that it's not receiving enough juice. I could understand a portable HDD, but a mouse?

    If you are using a 3rd party mouse, check the manufacturer site to see if you need to update any drivers.
    Trash the mouse preference, restart your computer and empty the trash.
    Resetting your Mac's PRAM and NVRAM

Maybe you are looking for

  • Runtime Errors Raise Exception in Solution Manager

    Hi Guru's, While I try to excute the transaction solman_issue_mgnt in solution manager for issue tracking, runtime errors occurs. Error analysis     A RAISE statement in the program "CL_GUI_HTML_VIEWER============CP" raised the      exception     con

  • OS 10.4.6 and display connector

    In March I got a G4 Mini to replace my old Mac. In the formidable process of getting all my functions to work on the Mini, I would have to swap computers several times, so I did not screw the connector from my monitor to the adapter on the Mini. In a

  • Problem With Org Id - Operating Unit

    Hi All, I open a session in an instance of database. I set the org_id in this way : begin dbms_application_info.set_client_info(131); end; When I run this query "select org_id from po_headers", the only purchase orders that appear are related with or

  • Reference field in the smartform

    hello, can you help me to specify reference field in smartform. That means, i had created the structure in which there is a field VEMNG for which the reference field is VEMEH from reference table VEPO. Then i had written the program and created the i

  • Account Lookup Case sensative - make insensative

    Hello, When looking up an account or searching for an account within the application is there a way to make the Account Lookup field not be case sensitive or a wild card that can be added. The "is like" doesn't work. Thanks