ThinkPad W520 Docking Station

Hey, everyone. My ThinkPad W520 should be arriving here tomorrow, and along with it, I ordered the ThinkPad Mini Dock Plus Series 3 - 170W. Currently, I have two monitors, one running at a resolution of 2048x1152, and the other one running at 1680x1050. I'm just now seeing that the limitation for the DVI ports is 1920x1080, so I'm guessing that won't work to hook these up.
My other route that I can go is by buying a DVI to DisplayPort cable, and then hooking them up that way. Lenovo's site claims that the dock has "Two DisplayPorts supporting 2560 x 1600 resolution," but would that mean I can hook up (these) two displays simultaneously? Inside the W520, is the NVIDIA Quadro 2000M Graphics with 2GB DDR3 Memory.
Thanks in advanced!
-Joe

well the real limitation of the single link dvi port is actually the 2048x1152 @ 60 hz, but this resolution monitor is seldomly used so they just use WUXGA or FHD as the stated maximum, 30 inch or 27 inch high resolution LCD uses dual link dvi (which is not supported by the dock dvi).
You can hock up two displayport monitors up and still run the internal LCD, since the new W520 uses the optimus graphics technology.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Similar Messages

Thinkpad 433835U Docking Station W520 - USB Ports Not Working

I have recently purchased the 433835U Docking Station and have the same issue in which when I have my W520 docked, NONE of the USB ports work at all. In Device Manager, I have an Unknown Device with the Hardware Ids of:
USB\VID_17EF&PID_100A&REV_0000 and USB\VID_17EF&PID_100A.
Yesterday I had a technician come on-site and replace the motherboard on my W520 and I am having the same results. I am also the owner of a Lenovo T410s and when using the same 433835U Dock, all of the USB ports work as expected, so it can not be a problem with the docking station.
I have called Lenovo Technical Support for the past two days and was told that there could be a compatibility issue with the W520 and this dock and I can not find the proper driver for the Unknown Device Hardware Ids listed above.
Do the USB port on this 433835U Docking Station work at all for anyone else with a W520?
Can anyone provide and insight as to resolve this Unknown Device issue? I am thinking about purchasing the 433830U Docking Station to see if it might work.
Thanks much in advance

I have the 433830U dock and the USB ports all work fine with my W520.

W500/w520 docking station

Hi everyone,
I get a laptop through my school every two years. I currently have a w500, but next year we will be recieving new w520 thinkpads. I was wondering if the current mini series 3 docking station is compatible with my current w500, and later for the w520.

no the Series 3 docking station is not compatible with the W500, have a look at this KB article.
For the W520 you would need this dock:
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-76767
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

W520 Docking station not working with exterma DP monitors

It used to work. Recently, however, if I reboot the thinkpad in the doc, I lose the two DP external monitors.
I.e. the machine boots on internal display, and if I go to windows "screen resolution" I can see the names of the two external monitors greyed out with the wrong resolution.
If I do a WINDOWS-P, then extend to the second one, then make the third the "main display", then disable the internal panel, Im back to where I should be. If I sleep and wakeup, it keeps the arrangement. If I dock the notebook while running, it automatically jumps to the correct arrangeement (i.e. internal panel off, two external displays extended).
Its only if I boot when in in the doc it fails, and I ahve to wait for 5 minutes fo tthe machine to boot, then faf about for another minute to get the displays working. I have never had this problem with Dell laptops in docking stations with external displays.
I dont expect a solution - and I accept im probably the only person who gets this error.
The machine cant reboot (I can only shutdown and cold boot) since I enabled password protection for the HD in the bios, so I cant test that.

With Optimus enabled, the W520 and other Optimus machines lose their brains on a restart. This is present in the T420 and the T420S, too.
I have just gotten used to doing shutdowns.

Thinkpad A31 Docking Station

Hi there,
I have a Thinkpad A31 - 2652 with Windows XP (SP3) and I would like to get a docking tray with the ability to have dual VGA monitors (both external monitors).  I understand that the "ThinkPad T, A, and X Series Dock" has both a VGA and a DVI  I/O ports. But, here are my questions, what kind of DVI is included with this dock? Would it be possible then to get a DVI - VGA adapter and attach a monitor to it so the diplay is extended to the second monitor, not just replicated in the second monitor?
Thank you.

I have a T-30 XP Pro that I used a type 2878 Docking Station for a while. Yes, I put on a DVI adaptor and it looks like you can do 2 x AGP.

W520 Docking station usb ports

Ok so I have a W520 and have it in it's proper docking station. I was wondering if the USB ports on the BACK of the docking station are USB 3.0, or 2.0. I'd prefer if it was 3.0 but theres no way to tell. Hoping someone could help me out.
Thanks!
Solved!
Go to Solution.

Yes. I have the W520 and doc, and all doc USB ports are USB 2.0
I have to plug my USB devices directly into the USB ports on the W520.

FOR SALE - Lenovo Thinkpad Tablet, Docking Station and Keyboard Folio Case

As my daughter is insisting on a laptop, her Thinkpad Tablet and Accessories will have to go....
The tablet is the 16GB WiFi Version (1838-5SG). The Docking Station is the standard one (0A33965), as is the Keyboard Folio Case (which is a Western European keyboard type - ASM P/N 0B33512 FRU P/N 03X6354).
The Tablet has one very tiny scratch on the screen, hardly noticeable, other than that is in perfect condition (the Styuls Pen is only 4 months old). The Docking Station has a slot cut out to enable a mini HDMI Cable to be connected through the facia (to the tablet), and other than that, is in perfect condition. The Folio Keyboard Case is in perfect condition. All cables, etc are included, and the Docking Station power cable has an EU plug (note that if you live in a Country which doesn't have EU Plug sockets, a standard plug can be purchased separately from the adaptor, they normally cost pennies....)
All boxes, packaging, instructions, etc are included, including the receipts for warranty purposes. The tablet and docking station are less than 1 year old, as verified by the receipts.
I can send full info, including photos, etc, if needed.
If anyone is interested, please make me an offer.

I was thinking i could use this Motorola Wireless Keyboard, it only needs an HID bluetooth connection, the ThinkPad Tab supports HID?

Thinkpad 8 Docking Station?

Does anybody know of a officialy compatible docking station for Thinkpad Tablet 8?

Most of us are using the Lenovo USB Y-cable 4X90G54343, but it is getting hard to find. Not aware of an actual dock, like the TP10's.

W520 docking station audio problems

My new W520 is nice but it has a few quirks:
1. When plugged into the docking station, my external speakers (Klipshe desktop) have bad background noise, like grinding metal when volume knob is at 20% or more. Unplugging the audio (green) cable from the docking station eliminates the noise, and the cable works great when plugged into my iPhone. The noise is apparently coming from the docking station!
2. Undocking the W520 causes the audio to no longer work. The Control Panel, Sound page shows just "Conexant 20672 SmartAudio HD" default device. That test results in "Failed to play test tone".
Any help or recommendations is appreciated !
Thank you,
Steve

Also please check Lenovo.com for an updated driver. I think there have been 2 drivers out in the past 3 weeks for the Conexant.
Perry
Perry
W520, I7 2720QM, M4 512 GB SSD OS/Program Disk, C300 256 GB Data Disk in Ultrabay Caddy; X220, I7 2620, Samsung 256 GB SSD, Intel 310 mSata Drv, T61, ancient but working, Asus MoBo, I7 2600k overclocked

Thinkpad T420s docking station

What docking station is compatible with this machine?

The same ones that the previous T-Series use.
EDIT: Here's the link.
http://shop.lenovo.com/SEUILibrary/controller/e/web/LenovoPortal/en_US/catalog.workflow:item.detail?...
This one has no eSata port and one less DVI, DisplayPort connectors.
http://shop.lenovo.com/SEUILibrary/controller/e/web/LenovoPortal/en_US/catalog.workflow:item.detail?...

W520 docking station ethernet not working

Again another small issue with the docking station. Before I begin, i'll let you know i've tested the router, the cables, and other sorts, and they are all working. So i don't think that's the issue.
My issue is that when I plug my ethernet cable into the back of my docking station, i get an ip address, but cannot connect to any websites. However, if i undock and take THAT SAME CABLE and plug it directly into the laptop, i get an ip address but can also connect to websites. Any thoughts? i thought it might be a driver issue, but i just updated everything on the computer and still no luck.
Any help would be greatly appreciated. Thank you

Not sure if this is the case with your docking station, but in the past, the ethernet NIC in the Lenovo docking bays were actually a third NIC, not a pass-thru. So it is conceivable that the IP settings (in particular Default Gateway and the DNS server addresses) are not set correctly.
Plug your docking bay back into Ethernet, and after you get your IP address, open up a command prompt, try IPCONFIG /ALL, and see what you get back.

X61 dock station and Linux

I have a Thinkpad X61. I bought it without a dock station and I never needed one. Now I need and I want to buy one. It will probably be second hand but that doesn't matter
I want to know if someone used a docking station with Linux distro (Ubuntu or Fedora pref.) I have concerns about network issues.
Thanks.

I can't specifically give you any guarantees about X61, but I've used several Thinkpads with docking stations under Linux, and so have my colleagues at work, and I've never heard about any problems.
I love docking stations and I think they are well worth it if you can find one cheap. eBay in the US seems to be full of them, though shipping to Bulgaria might be a different matter...
As to your hard drive question, the following link should tell you all you need to know:
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-62432

Problem using DVD/CD drive with Thinkpad Advanced Dock -- drive gets "lost" on start-up

Hello, I have a Thinkpad Advanced Docking station, a Thinkpad T60p, and an UltraBay Slim Super Multi-Burner Drive (HL-DT-ST DVDRAM GSA-4083N) that I use in the docking station's expansion bay. Whenever I restart the docking station and computer, the multi-burner drive becomes "lost" -- I have to physically remove the drive and re-insert it for the computer to recognize the drive.
Has anyone else experienced this problem?
Does anyone know how to get around it?

Yes, I have had the same problem. I have the HP Pavilion 14.1" but similar stuff. I don't know if you noticed searching but there are a LOT of people who have this problem. Apple won't help me because they say its not them. HP and Costco Tech Support can't figure it out and I don't have another 3+ hours to sit on the phone more to figure it out. Its an issue with Apple and Windows believe it or not, I am considering selling my ipod and not using itunes to purchase music and movies anymore. So are friends. The ONE way to fix it is you go into the regedit and delete the upper and lower drive filters for the drive. The problem with this is now when you go back into itunes it will no longer recognize your drive. So two options you are left with A) Itunes working without your cd drive working at all OR B) your cd drive working for everything BUT itunes and when you use itunes you get that message about not finding your cd drive. So no matter what you do, itunes and your drive will never work together. That is just how it is and NO SOLUTION has been found. Apple doesn't know or care. HP or Microsoft has no idea because its something Apple did. And despite people frantically trying to find solutions online, there really doesn't seem to be any to this point. If someone finds a viable working solution to this problem to get your drive and itunes to work TOGETHER even after restarting, I would be VERY HAPPY as well as 'computerguy'!

Dual Screen ThinkPad W520 with docking station

I'm trying to use an external monitor with my docking station to extend my desktop but I can't get it to work.
I'm using the intel HD video card and I already followed thoses guide
https://wiki.archlinux.org/index.php/Intel
https://wiki.archlinux.org/index.php/Xo … ual_screen
/etc/X11/xorg.conf.d/20-intel.conf
Section "Device"
Identifier "old intel stuff"
Driver "intel"
Option "Shadow" "True"
Option "DRI" "false"
EndSection
/etc/modprobe.d/modprobe.conf
options i915 modeset=1
/etc/mkinitcpio.conf
MODULES="intel_agp i915"
FILES="/etc/modprobe.d/modprobe.conf
mkinitcpio -p linux
reboot
The output of xrandr -q is VGA1 disconnected even if it's plugged in the dock or the laptop itself.
Do you guys have any clues?
thanks

I'm not sure what log message I should look at. I already looked at the Xorg log
[ 184.940]
X.Org X Server 1.11.3
Release Date: 2011-12-16
[ 184.941] X Protocol Version 11, Revision 0
[ 184.941] Build Operating System: Linux 3.1.5-1-ARCH x86_64
[ 184.941] Current Operating System: Linux DUDE-ARCHLINUX 3.2.1-1-ARCH #1 SMP PREEMPT Fri Jan 13 06:50:31 CET 2012 x86_64
[ 184.941] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=/dev/disk/by-uuid/216a6a09-6be1-47c8-8147-377642302ba6 ro quiet splash
[ 184.941] Build Date: 17 December 2011 09:17:41AM
[ 184.941]
[ 184.941] Current version of pixman: 0.24.0
[ 184.941] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 184.941] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 184.942] (==) Log file: "/var/log/Xorg.0.log", Time: Tue Jan 24 09:14:51 2012
[ 184.951] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 184.980] (==) No Layout section. Using the first Screen section.
[ 184.980] (**) |-->Screen "Screen0" (0)
[ 184.980] (**) | |-->Monitor "Monitor0"
[ 184.980] (**) | |-->Device "Device0"
[ 184.980] (==) Automatically adding devices
[ 184.980] (==) Automatically enabling devices
[ 185.024] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 185.024] Entry deleted from font path.
[ 185.043] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 185.043] Entry deleted from font path.
[ 185.043] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 185.044] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 185.044] Entry deleted from font path.
[ 185.044] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 185.044] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 185.044] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 185.044] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 185.044] (II) Loader magic: 0x7ccae0
[ 185.044] (II) Module ABI versions:
[ 185.044] X.Org ANSI C Emulation: 0.4
[ 185.044] X.Org Video Driver: 11.0
[ 185.044] X.Org XInput driver : 13.0
[ 185.044] X.Org Server Extension : 6.0
[ 185.046] (--) PCI:*(0:0:2:0) 8086:0126:17aa:21d1 rev 9, Mem @ 0xf1400000/4194304, 0xe0000000/268435456, I/O @ 0x00006000/64
[ 185.046] (--) PCI: (0:1:0:0) 10de:0dfa:17aa:21d1 rev 161, Mem @ 0xf0000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x00005000/128, BIOS @ 0x????????/524288
[ 185.046] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 185.046] (II) LoadModule: "extmod"
[ 185.075] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 185.089] (II) Module extmod: vendor="X.Org Foundation"
[ 185.089] compiled for 1.11.3, module version = 1.0.0
[ 185.089] Module class: X.Org Server Extension
[ 185.089] ABI class: X.Org Server Extension, version 6.0
[ 185.089] (II) Loading extension MIT-SCREEN-SAVER
[ 185.089] (II) Loading extension XFree86-VidModeExtension
[ 185.089] (II) Loading extension XFree86-DGA
[ 185.089] (II) Loading extension DPMS
[ 185.089] (II) Loading extension XVideo
[ 185.089] (II) Loading extension XVideo-MotionCompensation
[ 185.089] (II) Loading extension X-Resource
[ 185.089] (II) LoadModule: "dbe"
[ 185.089] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 185.090] (II) Module dbe: vendor="X.Org Foundation"
[ 185.090] compiled for 1.11.3, module version = 1.0.0
[ 185.090] Module class: X.Org Server Extension
[ 185.090] ABI class: X.Org Server Extension, version 6.0
[ 185.090] (II) Loading extension DOUBLE-BUFFER
[ 185.090] (II) LoadModule: "glx"
[ 185.090] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 185.104] (II) Module glx: vendor="X.Org Foundation"
[ 185.105] compiled for 1.11.3, module version = 1.0.0
[ 185.105] ABI class: X.Org Server Extension, version 6.0
[ 185.105] (==) AIGLX enabled
[ 185.105] (II) Loading extension GLX
[ 185.105] (II) LoadModule: "record"
[ 185.105] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 185.106] (II) Module record: vendor="X.Org Foundation"
[ 185.106] compiled for 1.11.3, module version = 1.13.0
[ 185.106] Module class: X.Org Server Extension
[ 185.106] ABI class: X.Org Server Extension, version 6.0
[ 185.106] (II) Loading extension RECORD
[ 185.106] (II) LoadModule: "dri"
[ 185.106] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 185.117] (II) Module dri: vendor="X.Org Foundation"
[ 185.117] compiled for 1.11.3, module version = 1.0.0
[ 185.117] ABI class: X.Org Server Extension, version 6.0
[ 185.117] (II) Loading extension XFree86-DRI
[ 185.117] (II) LoadModule: "dri2"
[ 185.118] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 185.118] (II) Module dri2: vendor="X.Org Foundation"
[ 185.118] compiled for 1.11.3, module version = 1.2.0
[ 185.118] ABI class: X.Org Server Extension, version 6.0
[ 185.118] (II) Loading extension DRI2
[ 185.118] (II) LoadModule: "intel"
[ 185.119] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 185.135] (II) Module intel: vendor="X.Org Foundation"
[ 185.135] compiled for 1.11.2, module version = 2.17.0
[ 185.135] Module class: X.Org Video Driver
[ 185.135] ABI class: X.Org Video Driver, version 11.0
[ 185.135] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server
[ 185.136] (--) using VT number 7
[ 185.148] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 185.148] drmOpenDevice: node name is /dev/dri/card0
[ 185.148] drmOpenDevice: open result is 8, (OK)
[ 185.148] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 185.148] drmOpenDevice: node name is /dev/dri/card0
[ 185.148] drmOpenDevice: open result is 8, (OK)
[ 185.148] drmOpenByBusid: drmOpenMinor returns 8
[ 185.148] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 185.148] (**) intel(0): Depth 24, (--) framebuffer bpp 32
[ 185.148] (==) intel(0): RGB weight 888
[ 185.148] (==) intel(0): Default visual is TrueColor
[ 185.148] (**) intel(0): Option "DRI" "false"
[ 185.148] (**) intel(0): Option "Shadow" "True"
[ 185.148] (II) intel(0): Integrated Graphics Chipset: Intel(R) Sandybridge Mobile (GT2+)
[ 185.148] (--) intel(0): Chipset: "Sandybridge Mobile (GT2+)"
[ 185.149] (**) intel(0): Shadow buffer enabled, 2D GPU acceleration disabled.
[ 185.149] (**) intel(0): Relaxed fencing enabled
[ 185.149] (**) intel(0): Wait on SwapBuffers? enabled
[ 185.149] (**) intel(0): Triple buffering? enabled
[ 185.149] (**) intel(0): Framebuffer tiled
[ 185.149] (**) intel(0): Pixmaps tiled
[ 185.149] (**) intel(0): 3D buffers tiled
[ 185.149] (**) intel(0): SwapBuffers wait enabled
[ 185.149] (==) intel(0): video overlay key set to 0x101fe
[ 185.149] (II) intel(0): Output LVDS1 using monitor section Monitor0
[ 185.149] (II) intel(0): found backlight control interface /sys/class/backlight/acpi_video1
[ 185.149] (II) intel(0): Output VGA1 has no monitor section
[ 185.150] (II) intel(0): EDID for output LVDS1
[ 185.150] (II) intel(0): Manufacturer: LEN Model: 40b1 Serial#: 0
[ 185.150] (II) intel(0): Year: 2009 Week: 0
[ 185.150] (II) intel(0): EDID Version: 1.3
[ 185.150] (II) intel(0): Digital Display Input
[ 185.150] (II) intel(0): Max Image Size [cm]: horiz.: 35 vert.: 19
[ 185.150] (II) intel(0): Gamma: 2.20
[ 185.150] (II) intel(0): DPMS capabilities: StandBy Suspend Off
[ 185.150] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 185.150] (II) intel(0): First detailed timing is preferred mode
[ 185.150] (II) intel(0): redX: 0.610 redY: 0.348 greenX: 0.316 greenY: 0.589
[ 185.150] (II) intel(0): blueX: 0.151 blueY: 0.066 whiteX: 0.313 whiteY: 0.329
[ 185.150] (II) intel(0): Manufacturer's mask: 0
[ 185.150] (II) intel(0): Supported detailed timing:
[ 185.150] (II) intel(0): clock: 108.5 MHz Image Size: 345 x 194 mm
[ 185.150] (II) intel(0): h_active: 1600 h_sync: 1648 h_sync_end 1680 h_blank_end 1920 h_border: 0
[ 185.150] (II) intel(0): v_active: 900 v_sync: 903 v_sync_end 908 v_blanking: 942 v_border: 0
[ 185.150] (II) intel(0): Supported detailed timing:
[ 185.150] (II) intel(0): clock: 90.4 MHz Image Size: 345 x 194 mm
[ 185.150] (II) intel(0): h_active: 1600 h_sync: 1648 h_sync_end 1680 h_blank_end 1920 h_border: 0
[ 185.150] (II) intel(0): v_active: 900 v_sync: 903 v_sync_end 908 v_blanking: 942 v_border: 0
[ 185.150] (II) intel(0): Unknown vendor-specific block f
[ 185.150] (II) intel(0): LP156WD1-TLB2
[ 185.150] (II) intel(0): EDID (in hex):
[ 185.150] (II) intel(0): 00ffffffffffff0030aeb14000000000
[ 185.150] (II) intel(0): 0013010380231378ea43c59c59519626
[ 185.150] (II) intel(0): 11505400000001010101010101010101
[ 185.150] (II) intel(0): 010101010101622a404061842a303020
[ 185.150] (II) intel(0): 350059c2100000195323404061842a30
[ 185.150] (II) intel(0): 3020350059c2100000190000000f00a9
[ 185.150] (II) intel(0): 0932a9092816090030e40002000000fe
[ 185.150] (II) intel(0): 004c503135365744312d544c423200e2
[ 185.150] (II) intel(0): EDID vendor "LEN", prod id 16561
[ 185.151] (II) intel(0): Printing DDC gathered Modelines:
[ 185.151] (II) intel(0): Modeline "1600x900"x0.0 108.50 1600 1648 1680 1920 900 903 908 942 -hsync -vsync (56.5 kHz)
[ 185.151] (II) intel(0): Modeline "1600x900"x0.0 90.43 1600 1648 1680 1920 900 903 908 942 -hsync -vsync (47.1 kHz)
[ 185.151] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 185.151] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 185.151] (II) intel(0): Printing probed modes for output LVDS1
[ 185.151] (II) intel(0): Modeline "1600x900"x60.0 108.50 1600 1648 1680 1920 900 903 908 942 -hsync -vsync (56.5 kHz)
[ 185.151] (II) intel(0): Modeline "1600x900"x50.0 90.43 1600 1648 1680 1920 900 903 908 942 -hsync -vsync (47.1 kHz)
[ 185.151] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 185.151] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 185.151] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 185.151] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 185.151] (II) intel(0): EDID for output VGA1
[ 185.151] (II) intel(0): Output LVDS1 connected
[ 185.151] (II) intel(0): Output VGA1 disconnected
[ 185.151] (II) intel(0): Using exact sizes for initial modes
[ 185.151] (II) intel(0): Output LVDS1 using initial mode 1600x900
[ 185.152] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 185.152] (II) intel(0): Kernel page flipping support detected, enabling
[ 185.152] (**) intel(0): Display dimensions: (448, 254) mm
[ 185.152] (WW) intel(0): Probed monitor is 350x190 mm, using Displaysize 448x254 mm
[ 185.152] (**) intel(0): DPI set to (90, 90)
[ 185.152] (II) Loading sub module "fb"
[ 185.152] (II) LoadModule: "fb"
[ 185.152] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 185.153] (II) Module fb: vendor="X.Org Foundation"
[ 185.153] compiled for 1.11.3, module version = 1.0.0
[ 185.153] ABI class: X.Org ANSI C Emulation, version 0.4
[ 185.153] (==) Depth 24 pixmap format is 32 bpp
[ 185.153] (II) intel(0): Allocated new frame buffer 1600x900 stride 6656, tiled
[ 185.157] (II) UXA(0): Driver registered support for the following operations:
[ 185.157] (II) solid
[ 185.157] (II) copy
[ 185.157] (II) composite (RENDER acceleration)
[ 185.157] (II) put_image
[ 185.157] (II) get_image
[ 185.157] (==) intel(0): Backing store disabled
[ 185.157] (==) intel(0): Silken mouse enabled
[ 185.157] (II) intel(0): Initializing HW Cursor
[ 185.223] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 185.227] (==) intel(0): DPMS enabled
[ 185.227] (==) intel(0): Intel XvMC decoder enabled
[ 185.227] (WW) intel(0): Disabling Xv because no adaptors could be initialized.
[ 185.227] (II) intel(0): direct rendering: Disabled
[ 185.227] (==) intel(0): hotplug detection: "enabled"
[ 185.227] (--) RandR disabled
[ 185.227] (II) Initializing built-in extension Generic Event Extension
[ 185.227] (II) Initializing built-in extension SHAPE
[ 185.227] (II) Initializing built-in extension MIT-SHM
[ 185.227] (II) Initializing built-in extension XInputExtension
[ 185.227] (II) Initializing built-in extension XTEST
[ 185.227] (II) Initializing built-in extension BIG-REQUESTS
[ 185.227] (II) Initializing built-in extension SYNC
[ 185.227] (II) Initializing built-in extension XKEYBOARD
[ 185.227] (II) Initializing built-in extension XC-MISC
[ 185.227] (II) Initializing built-in extension SECURITY
[ 185.227] (II) Initializing built-in extension XINERAMA
[ 185.227] (II) Initializing built-in extension XFIXES
[ 185.227] (II) Initializing built-in extension RENDER
[ 185.227] (II) Initializing built-in extension RANDR
[ 185.227] (II) Initializing built-in extension COMPOSITE
[ 185.227] (II) Initializing built-in extension DAMAGE
[ 185.254] (II) AIGLX: Screen 0 is not DRI2 capable
[ 185.254] (II) AIGLX: Screen 0 is not DRI capable
[ 185.582] (II) AIGLX: Loaded and initialized swrast
[ 185.582] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[ 185.583] (II) intel(0): Setting screen physical size to 448 x 254
[ 185.918] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[ 185.918] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 185.918] (**) Power Button: Applying InputClass "keyboard-layout"
[ 185.918] (II) LoadModule: "evdev"
[ 185.919] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 185.932] (II) Module evdev: vendor="X.Org Foundation"
[ 185.932] compiled for 1.10.99.902, module version = 2.6.0
[ 185.932] Module class: X.Org XInput Driver
[ 185.932] ABI class: X.Org XInput driver, version 13.0
[ 185.932] (II) Using input driver 'evdev' for 'Power Button'
[ 185.933] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 185.933] (**) Power Button: always reports core events
[ 185.933] (**) Power Button: Device: "/dev/input/event3"
[ 185.933] (--) Power Button: Found keys
[ 185.933] (II) Power Button: Configuring as keyboard
[ 185.933] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"
[ 185.933] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 185.933] (**) Option "xkb_rules" "evdev"
[ 185.933] (**) Option "xkb_model" "evdev"
[ 185.933] (**) Option "xkb_layout" "us, ca"
[ 185.933] (**) Option "xkb_options" "grp:caps_toggle"
[ 185.997] (II) config/udev: Adding input device Video Bus (/dev/input/event4)
[ 185.997] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 185.997] (**) Video Bus: Applying InputClass "keyboard-layout"
[ 185.997] (II) Using input driver 'evdev' for 'Video Bus'
[ 185.997] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 185.997] (**) Video Bus: always reports core events
[ 185.997] (**) Video Bus: Device: "/dev/input/event4"
[ 185.997] (--) Video Bus: Found keys
[ 185.997] (II) Video Bus: Configuring as keyboard
[ 185.997] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4/event4"
[ 185.997] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 185.997] (**) Option "xkb_rules" "evdev"
[ 185.997] (**) Option "xkb_model" "evdev"
[ 185.997] (**) Option "xkb_layout" "us, ca"
[ 185.997] (**) Option "xkb_options" "grp:caps_toggle"
[ 185.999] (II) config/udev: Adding input device Video Bus (/dev/input/event5)
[ 185.999] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 185.999] (**) Video Bus: Applying InputClass "keyboard-layout"
[ 185.999] (II) Using input driver 'evdev' for 'Video Bus'
[ 185.999] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 185.999] (**) Video Bus: always reports core events
[ 185.999] (**) Video Bus: Device: "/dev/input/event5"
[ 185.999] (--) Video Bus: Found keys
[ 185.999] (II) Video Bus: Configuring as keyboard
[ 185.999] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:0a/LNXVIDEO:01/input/input5/event5"
[ 185.999] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)
[ 185.999] (**) Option "xkb_rules" "evdev"
[ 185.999] (**) Option "xkb_model" "evdev"
[ 185.999] (**) Option "xkb_layout" "us, ca"
[ 185.999] (**) Option "xkb_options" "grp:caps_toggle"
[ 186.000] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[ 186.000] (II) No input driver/identifier specified (ignoring)
[ 186.001] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[ 186.001] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 186.001] (**) Sleep Button: Applying InputClass "keyboard-layout"
[ 186.001] (II) Using input driver 'evdev' for 'Sleep Button'
[ 186.001] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 186.001] (**) Sleep Button: always reports core events
[ 186.001] (**) Sleep Button: Device: "/dev/input/event2"
[ 186.001] (--) Sleep Button: Found keys
[ 186.001] (II) Sleep Button: Configuring as keyboard
[ 186.001] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2/event2"
[ 186.001] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[ 186.001] (**) Option "xkb_rules" "evdev"
[ 186.001] (**) Option "xkb_model" "evdev"
[ 186.001] (**) Option "xkb_layout" "us, ca"
[ 186.001] (**) Option "xkb_options" "grp:caps_toggle"
[ 186.002] (II) config/udev: Adding input device Integrated Camera (/dev/input/event8)
[ 186.002] (**) Integrated Camera: Applying InputClass "evdev keyboard catchall"
[ 186.002] (**) Integrated Camera: Applying InputClass "keyboard-layout"
[ 186.002] (II) Using input driver 'evdev' for 'Integrated Camera'
[ 186.002] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 186.002] (**) Integrated Camera: always reports core events
[ 186.002] (**) Integrated Camera: Device: "/dev/input/event8"
[ 186.003] (--) Integrated Camera: Found keys
[ 186.003] (II) Integrated Camera: Configuring as keyboard
[ 186.003] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input8/event8"
[ 186.003] (II) XINPUT: Adding extended input device "Integrated Camera" (type: KEYBOARD, id 10)
[ 186.003] (**) Option "xkb_rules" "evdev"
[ 186.003] (**) Option "xkb_model" "evdev"
[ 186.003] (**) Option "xkb_layout" "us, ca"
[ 186.003] (**) Option "xkb_options" "grp:caps_toggle"
[ 186.004] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event7)
[ 186.004] (II) No input driver/identifier specified (ignoring)
[ 186.004] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 186.004] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 186.004] (**) AT Translated Set 2 keyboard: Applying InputClass "keyboard-layout"
[ 186.004] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 186.005] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 186.005] (**) AT Translated Set 2 keyboard: always reports core events
[ 186.005] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 186.005] (--) AT Translated Set 2 keyboard: Found keys
[ 186.005] (II) AT Translated Set 2 keyboard: Configuring as keyboard
[ 186.005] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 186.005] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 11)
[ 186.005] (**) Option "xkb_rules" "evdev"
[ 186.005] (**) Option "xkb_model" "evdev"
[ 186.005] (**) Option "xkb_layout" "us, ca"
[ 186.005] (**) Option "xkb_options" "grp:caps_toggle"
[ 186.006] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event9)
[ 186.006] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 186.006] (II) LoadModule: "synaptics"
[ 186.006] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 186.016] (II) Module synaptics: vendor="X.Org Foundation"
[ 186.016] compiled for 1.11.0, module version = 1.5.0
[ 186.016] Module class: X.Org XInput Driver
[ 186.016] ABI class: X.Org XInput driver, version 13.0
[ 186.016] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[ 186.016] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 186.016] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 186.016] (**) Option "Device" "/dev/input/event9"
[ 186.346] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5888
[ 186.346] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4820
[ 186.346] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 186.346] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 0
[ 186.346] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left right double triple
[ 186.346] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[ 186.346] (**) Option "TapButton1" "1"
[ 186.346] (**) Option "TapButton2" "2"
[ 186.347] (**) Option "TapButton3" "3"
[ 186.453] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 186.453] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 186.560] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input9/event9"
[ 186.560] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 12)
[ 186.560] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[ 186.560] (**) synaptics: SynPS/2 Synaptics TouchPad: MaxSpeed is now 1.75
[ 186.560] (**) synaptics: SynPS/2 Synaptics TouchPad: AccelFactor is now 0.036
[ 186.560] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 186.560] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[ 186.560] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 186.560] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 186.560] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 186.561] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0)
[ 186.561] (II) No input driver/identifier specified (ignoring)
[ 186.562] (II) config/udev: Adding input device TPPS/2 IBM TrackPoint (/dev/input/event10)
[ 186.562] (**) TPPS/2 IBM TrackPoint: Applying InputClass "evdev pointer catchall"
[ 186.562] (II) Using input driver 'evdev' for 'TPPS/2 IBM TrackPoint'
[ 186.562] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 186.562] (**) TPPS/2 IBM TrackPoint: always reports core events
[ 186.562] (**) TPPS/2 IBM TrackPoint: Device: "/dev/input/event10"
[ 186.562] (--) TPPS/2 IBM TrackPoint: Found 3 mouse buttons
[ 186.562] (--) TPPS/2 IBM TrackPoint: Found relative axes
[ 186.562] (--) TPPS/2 IBM TrackPoint: Found x and y relative axes
[ 186.562] (II) TPPS/2 IBM TrackPoint: Configuring as mouse
[ 186.562] (**) TPPS/2 IBM TrackPoint: YAxisMapping: buttons 4 and 5
[ 186.562] (**) TPPS/2 IBM TrackPoint: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 186.562] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/serio2/input/input10/event10"
[ 186.562] (II) XINPUT: Adding extended input device "TPPS/2 IBM TrackPoint" (type: MOUSE, id 13)
[ 186.562] (II) TPPS/2 IBM TrackPoint: initialized for relative axes.
[ 186.562] (**) TPPS/2 IBM TrackPoint: (accel) keeping acceleration scheme 1
[ 186.563] (**) TPPS/2 IBM TrackPoint: (accel) acceleration profile 0
[ 186.563] (**) TPPS/2 IBM TrackPoint: (accel) acceleration factor: 2.000
[ 186.563] (**) TPPS/2 IBM TrackPoint: (accel) acceleration threshold: 4
[ 186.563] (II) config/udev: Adding input device TPPS/2 IBM TrackPoint (/dev/input/mouse1)
[ 186.563] (II) No input driver/identifier specified (ignoring)
[ 186.564] (II) config/udev: Adding input device ThinkPad Extra Buttons (/dev/input/event6)
[ 186.564] (**) ThinkPad Extra Buttons: Applying InputClass "evdev keyboard catchall"
[ 186.564] (**) ThinkPad Extra Buttons: Applying InputClass "keyboard-layout"
[ 186.564] (II) Using input driver 'evdev' for 'ThinkPad Extra Buttons'
[ 186.564] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 186.564] (**) ThinkPad Extra Buttons: always reports core events
[ 186.564] (**) ThinkPad Extra Buttons: Device: "/dev/input/event6"
[ 186.564] (--) ThinkPad Extra Buttons: Found keys
[ 186.564] (II) ThinkPad Extra Buttons: Configuring as keyboard
[ 186.564] (**) Option "config_info" "udev:/sys/devices/platform/thinkpad_acpi/input/input6/event6"
[ 186.564] (II) XINPUT: Adding extended input device "ThinkPad Extra Buttons" (type: KEYBOARD, id 14)
[ 186.564] (**) Option "xkb_rules" "evdev"
[ 186.564] (**) Option "xkb_model" "evdev"
[ 186.565] (**) Option "xkb_layout" "us, ca"
[ 186.565] (**) Option "xkb_options" "grp:caps_toggle"
Last edited by mtetreault (2012-01-24 14:17:56)

Not Getting "Undock" Option in Windows 7 with W520 in Docking Station

I just bought a W520 which is my 5th ThinkPad in about 10 years. This one is different in that I don't get the option to "Undock" in the Windows 7 "Shutdown" option list. I also noticed the W520 doesn't seat as securely into the docking station as my prior ThinkPads, but the docking station ports all work correctly.
Is there something wrong with my hardware or Windows 7 settings?

Hi all
I guess, this article would help
http://social.technet.microsoft.com/Forums/en-US/w7itproinstall/thread/94468d2b-4ae8-4228-90a6-2c5ae...
If the undock option is not available, you could just put your laptop into sleep mode (or simply close the lid by default) and just undock the docking station from it. Resuming from sleep mode does not take much time either.
Have a nice day!
Peter
W520 (4284-A99)
Does someone’s post help you? Give them kudos as a reward, as they will do better to improve | Mark it as solved if the solution works for you, so it could be reference for others in the future
=====================================
Sound Enthusiast and Enhancement (Post comments, share mixes, etc.)
http://forums.lenovo.com/t5/General-Discussion/Dolby-Home-Theater-v4-for-most-Lenovo-Laptops/td-p/62...

ThinkPad W520 Docking Station

Similar Messages

Maybe you are looking for