Thinkpad X1 and Windows 8

Hi i wanted to sum up what stuff doesn't work on Windows 8 for the Thinkpad X1. I use a Windows 8 Pro Version (Dreamspark) so it's not the costumerpreview or such thing. I installed all of the beta drivers provided by Lenovo.
1) Synaptic Ultranav: The driver simply fails to install. Cant't use gestures on the trackpad. Trackpoint runs but only with the default windows behavior (the scrolling is diffrently; ergo way worse).
2) There seems to be no Dolby Home Theater Support yet.
3) The Intel graphic driver lost it's option to turn off the automatic dimming of the display.
4) SystemUpdate gives back an error saying that the catalogue for the Thinkpad X1 were not found.
5) The mute microphone key doens't function -> no light on / microphone is constantly activated
6) Besides Display brightness none of the FN combinations work e.g. managing WLan and Bluetooth adapters
Ok, i will try to install the fingerprint reader, cardreader and so on. If i find more problems i'll post them here
Cheers,
Karl

Hi, maybe I can help.
1. Use the windows 7 version- works perfectly
2. New win8 drivers have it here-
http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?&DocID=HT074689
3. Try re-installing them as there's been a few added very recently.
4. Are you using version 5? (this automatically picked up the Audio Drivers with Dolby).
5. Need these driver-
http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?&DocID=HT074689
6. Again, sounds like your missing heaps of drivers.
Go nuts on the link above and come back to us if your still having problems.

Similar Messages

Comments on Thinkpad L420 and Windows 8.1

Hi
I installed Windows 8.1 build 9600 on a Thinkpad L420 to try it out.
Here are some of my comments.
1) ThinkVantage System Update does not install normally, you need to run the silent mode to install it.
Once it is installed it will install some of the drivers and Lenovo software on it.
You need to run it like this "SystemUpdate502-06-26-2013.exe /a /s /v"/qn"
Check this link: http://forums.lenovo.com/t5/Windows-8/Windows-8-1-Lenovo-system-update/td-p/1233289
Check the Thinkvantage software for Windows 8 here: http://support.lenovo.com/en_US/detail.page?LegacyDocID=migr-61432
2) For the intel drivers it is also good that you run the Intel autodetect tool on their website.
http://www.intel.com/p/en_US/support/detect
The newer intel video driver and Wifi are working fine on Windows 8.1
3) Bluetooth was not working. I went the the Broadcom site and downloaded the driver from their site. After installing it started working. (SetupBtwDownloadSE.exe)
Issues:
1) I can not make the "Fingerprint software". The figerprint device got recognized by Windows 8.1 like "Touchstrip Finger Print Sensor" by "AuthenTec" on Widows Device Manager.
But when I try to run Lenovo's Fingerprint software installer it tells me that Windows is missing the "Windows biometric framework".
Any tip on how to make it work will be welcome.
Regards.
Martin
Martín Itúrbide
OS2World.com NewsMaster
- Lenovo. Please unlock the Thinkpad Tablet bootloader
- Thinkpad Tablet 1838-22U
- Thinkpad L420 - 7853-3WS
- Thinkpad R51 - 1830-PS0
- ScrollPoint Pro Mouse
Solved!
Go to Solution.

We know about the issue with ThinkVantage Fingerprint Software and will have new software ready by the time Windows 8.1 is formally available.
But, Windows 8.1 has fingerprint software built-in so you can enroll your finger in the User Settings screen.
The only benefit to ThinkVantage Fingerprint Software, is the preboot support for T/W/X systems. Your L420 doesn't support fingerprint at preboot, therefore you don't need ThinkVantage Fingerprint Software for L420 on Win8.1 - there is no purpose for it.
So just install the Fingerprint driver from Windows Update (I think you already did this) and use the native Win8.1 fingerprint enrollment tool in the User Settings screen.

Thinkpad e530c and windows aero

Hi
i have a thinkpad e530c core i3 with 4GB ram and i've installed a fresh copy of windows 8.1 but i cannot see any of the aero or glassy features with it. is it a problem with my laptop or what?

I had previously constant problems with ATI X1400 driver on T60 under Windows 7, especially with external display.
Finally AMD/ATI released 10.2 catalyst driver
http://support.amd.com/us/gpudownload/windows/Legacy/Pages/radeonaiw_vista32.aspx?type=2.4.1&product...
which I can confirm works stable and supports external LCD in decent way.
(if you found errors while installing, this is due to ATI/Microsoft stupid installation build - you have to remove first all Microsoft Visual C install kits).
Unfortunately we've lost Presentation Director with W7 (Lenovo why ????), now we left with Windows+P or Catalyst, OK, at least works fine now.

ThinkPad R61 and Windows 8.1 issues

Hi,
I have installed Windows 8.1 on my R61 and have a problem with sleep/hibernate. It never goes to this state, iI should stead LCD switch off but computer still runs. The only way to get back is switch off power and restart.
If I manually disable wireless driver before pressing sleep, then it goes to sleep state succesfully. Which driver i should use.
Solved!
Go to Solution.

Just for information:
solution is recent Lenovo update - needed to install System Update and it proposes patch for Windows 8.1.
After patching sleep and Hibernate is working.

ThinkPad T440 and Windows XP

Hello,
does anybody know if the ThinkPad T440 still supports Windows XP (I don't think so)?
Kind regards
Alex
Solved!
Go to Solution.

T440 definitely does not support XP. As Microsoft will stop supporting XP within a couple months it did not make business sense to provide/test drivers for XP anymore. It is past time to start using a different OS.

Issues with Thinkpad yoga on Windows 7 64-bit

I uninstalled the windows 8.1 that came with my Thinkpad Yoga to installe windows 7 64-bit because there was no support for Power Manager ( a tool that allows you to charge your battery only upto a certain percentage (eg 40%) which helps reduce battery aging when the notebook is mostly operated on AC power).
Doing that required me to fully clean the Hard-disk during the installation process.
I installed almost all of the drivers available on http://support.lenovo.com/us/en/products/laptops-and-netbooks/thinkpad-yoga-series-laptops/thinkpad-...
for thinkpad yoga and windows 7 64 bit.
Happily, this provided me the Power manager, and I can use it just as I wanted.
However, all these has brought in additional issues which are listed below:
1. The touch pad right click doesn't work. Only two finger tap works as right click.
2. The touch pad gestures for zoom and scroll doesn't work at all.
3. The screen auto-rotate doesn't work.
4. The touch screen gesture for zoom doesn't work.
I did install the ultra-nav and screen-rotate drivers, but I get error messages regarding synaptics ... not working and also sensor driver not working during the windows startup.
Any help please?
Thank you.

Just when I was happy that major issues have been resolved by constant updating, I am now experiencing this frightening problem. Mostly during startup, and lately in the middle of working, the screen freezes, shows very damaged image (like TV noise), produces the most unpleasant sound through the speakers and nothing works. I need to restart and hope that it will be ok. Sometimes it requires 2 or 3 restarts, going to safe-mode and returning back to get the issue resolved.
This has happened three or 4 times within 24 hrs. I searched in the forum and for another model it was suggested that epresscache might be the cause. I disabled the service, but the problem reappeared even then.
Any help please:
This is what appears on the screen when the computer freezes and produces loud unpleasant noise sound.
Link to image
Moderator note: large image(s) converted to link(s): About Posting Pictures In The Forums

Thinkpad's and N100's w/ 945PM chipset can't address 3G Ram but Dell Can

Since I am a programmer, I am particularly interested in having the maximum amount of Ram available under 32 bit Windows.
Unfortunately, I have to buy a T61p to enable me to use 4GB.
From a reply to a NoteBook review Forum:
http://forum.notebookreview.com/archive/index.php/t-136639.html
At work, we have both Dell XPS and IBM/Lenovo Thinkpad laptops. We choose the T60 models for their compactness/weight and reliability, while we choose the XPS M1710 and M2010 for their 17 and 20-inch screens and somewhat faster graphics chips. The ThinkPad T60 computers have problems accessing over 3GB RAM, and that is NOT because of the chipset or the OS that we use, but, it is only because of the incompetent designers/engineers at IBM or Lenovo; let me explain:
We have tried to install both 32-bit and 64-bit version of Vista, Windows Server 2003 R2 STD, Win XP and different dists of LINUX on T60, T60p, Z61, Z61p, Z61m, (X60 and T43) and Lenovo 3000 series, but they simply can NOT access memory over 3GB (X60 and T43 can not support that since their chipset seem to have accessing issues over the magic 3GB, but we tried anyway)
We also tried the same thing on Dell XPS M1710 and M2010, and they could access almost the ENTIRE 4 GB installed even with 32-bit version of Windows Vista (BTW, 32-bit Vista can access 16 GB RAM with the right chipset so...). Of course, now you can guess that it was no problem with the 64-bit version of the OS:es we tried.
The Dell XPS M1710 and M2010 use exactly the same chipset found in T60 and Z60 series (Mobile Intel 945PM Express Chipset). In December 2006, we even opened a T60p (model 2007 8JG) and compared the chipset with the Dell XPS M1710, and well, I suppose that you have already guessed that it was the same chipset in both machines.
Honestly, I hoped that we would find the Mobile Intel 945 GM or GMS chipset in the T60 laptops (those chipsets seem to have this 3GB limit), since we had a BIG argue with the support guys at Lenovo, and they came with totally silly answers why the computers can not access over 3GB RAM. They even asked me what I need 4GB RAM for!! Can you imagine that?! You can ask ANY programmer/developer who works with virtual machines (both VPC and VMWare or even Parallels) and everyone will tell you that you can not have too much RAM!!! And it IS A BIG difference between 3GB and 4GB. However...
Now, we have heard rumors that HP NX94xx also can access 4GB RAM installed, but I can not confirm it myself, since I have not seen it myself.
And now, regarding to your post about mixing 2GB SO-DIMM with 1GB SO-DIMM, I would not recommend it. The 2GB SO-DIMM memory modules are pretty cheap now, and besides, you will lose a lot of speed mixing 2GB with 1GB memory modules. Just try different benchmarking programs and you will see. If you want to see quick results without a lot of installations, try Memtest86+
However, I think that it is very rotten that IBM/Lenovo does not care about their customers and lets a lot of incompetent technicians answer the phone. I have tried to come in contact with higher bosses and engineers, but they are simply unavailable. But it must be a way that we customers can make them hear us.. I only do not know how! :-/
And so, here ends my first (and long) post in here!
From the thinkpad forum, there is another confirmation, but the author is not aware that Dell did a better job with the P chipset:
T60/T61/p memory limitations -- the definitive answer [pics]
http://forum.thinkpads.com/viewtopic.php?t=49703
update 10/25/2007: now includes T60/p information.
T60 and T60p:
the T60 and T60p are based off of the intel socket M processors. no matter how much memory you install in these thinkpads, only 3GB will be addressable regardless of operating system used. this is a physical limitation and there is absolutely no workaround. if you have a T60/p then installing 4GB total system memory is a waste. save your money, stop at 3GB, and put the savings either in the bank or toward a T61/p if you want 4GB.
quoted from official lenovo documentation:
Quote: Maximum memory capacity may require the replacement of standard component with largest supported component available. On ThinkPad systems with an Intel 945GM, 945PM, GM965, or PM965 chipset, even though it is possible to physically install 4GB of memory, the actual amount of memory addressable by an operating system will be limited to 3GB. This limitation does not exist with the Intel GM965 and PM965 with the 64-bit operating systems Windows XP Professional 64-bit and Windows Vista 64-bit Editions.
the key point to take away from this quote: the T60 and T60p are based off of the 945GM and 945PM chipsets and therefore fall under the 3GB physical limitation as stated above. even with 4GB total system memory and a capable OS, you still can't see or use more 3GB no matter what you do.
T61 and T61p:
the T61 and T61p are based off of the intel socket P processors. these systems are capable of using up to 4GB total system memory as long as you use the proper OS. below are the results from the four most popular microsoft OSes tested on my T61p.

i wrote the article over at TPF regarding T60/1/p memory limitations.
while i've read that certain dell models can supposedly access all 4GB, i have yet to see definitive proof backing this up.   from my understanding, dell wrote their BIOSes to report the maximum installed memory but the systems still cannot utilize more than 3GB regardless of what is reported.   dell is the only manufacturer with a 945-based system which claims to use all 4GB so it leads me to think that something fishy is going on.   if the 945 could use more than 3GB then you'd think lenovo, apple, HP, etc. would have been able to pull it off as well.
before buying my T61p i performed weeks of research on the subject of 3GB/4GB limitations in chipsets.   i have yet to find definitive evidence showing that a merom-based system can truly access more than 3GB because of the chipset's lack of memory hoisting capability.   santa rosa seems to be the first mobile chipset supporting memory hoisting (which is necessary for moving memory addresses above the 4GB mark so that all 4GB of physical memory can be addressed by the OS).
the simple solution is to buy a T61p.   while the T60p did have optional IPS displays, the T61/p is better in absolutely every aspect except display quality.   i've had my hands on numerous T60/p systems of friends/family/colleagues and wouldn't trade my T61p for any of them.   my next upgrade won't happen until intel makes a mobile chipset able to address 8GB+ system memory (which santa rosa very well may be able to do but we won't know for sure until 4GB SODIMMs are released for public consumption).
ThinkStation C20
ThinkPad X1C · X220 · X60T · s30 · 600

Poor performance by Matlab and Windows benchmark tests

Hello
I have a Lenovo Thinkpad W520 with Windows 7 64bit installed. Compared to other Notebooks with comparable hardware, my Lenovo is very slow. To prove my thought, I carried through a Matlab (64bit) benchmark test and the Windows 7 benchmark test. In both tests, my Lenovo was worse than the other notebooks. During the tests I set the Power Manager to performance and activated the Lenovo turbo boost.
Now I want to ask, if there are any settings, perhaps in the bios, to speed the laptop up? Or why result such a bad performance although the hardware is very good?
Thanks for your help
Solved!
Go to Solution.

Thank you very much for your reply!
I dated up the BIOS from version 1.27 to 1.32. Now the benchmark tests all look great!!
Thanks

Thinkpad t500 and wifi card realtek RTL8192SE[solved]

I Buy a Lenovo Thinkpad T500 and the wireless adapter does not work in linux.
11b/g/n Wireless Lan Mini-PCI Express Adapter II.
lspci say:
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. Device e020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-ff-fe-22-55-88
lspci -n:
03:00.0 0280: 10ec:8172 (rev 10)
I need to buy another usb, pcmcia or mini pci-e wireless card.
Can you recommend one that works well? Because I never work with wifi cards on linux.
sorry my poor english
EDIT 21/07/09: add more information (thinkwiki):
http://www.thinkwiki.org/wiki/ThinkPad_ … Adapter_II
EDIT 22/10/09:
Finally came the expected driver, I think it's premature but it works perfectly.
Here the driver (r8192se_pci):
32bits: http://launchpadlibrarian.net/33927923/ … 009.tar.gz
64bits: http://launchpadlibrarian.net/34090326/ … bit.tar.gz
untar; make; make install; reboot and enjoy it
I test it with:
netcfg
standar commands:
ifconfig wlan0 up
iwlist wlan0 scan
iwconfig wlan0 essid MySsid
wpa_supplicant -B -Dwext -i wlan0 -c /etc/wpa_supplicant.conf
dhcpcd wlan0
The first time I compile the module, function correctly, but after scan for available networks I haven't any results.
Recompile and everything worked again
[b]I edit the wiki, pleased read it and help me because my English is a bit basic.
thanks
Last edited by takedown (2009-10-23 00:55:44)

Please note that the T500 has different hardware configurations.
Other options in wireless card (for the T500): intel 5100 - intel 5300.
This models work fine under linux
lspci -vv:
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
Subsystem: Lenovo Device 20e0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device 2114
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f4400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 41c9
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
Subsystem: Lenovo Device 2114
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f4200000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 Communication controller: Intel Corporation Mobile 4 Series Chipset MEI Controller (rev 07)
Subsystem: Lenovo Device 20e6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fc226800 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: heci
Kernel modules: heci
00:03.2 IDE interface: Intel Corporation Mobile 4 Series Chipset PT IDER Controller (rev 07) (prog-if 85 [Master SecO PriO])
Subsystem: Lenovo Device 20ea
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at 1828 [size=8]
Region 1: I/O ports at 180c [size=4]
Region 2: I/O ports at 1820 [size=8]
Region 3: I/O ports at 1808 [size=4]
Region 4: I/O ports at 1810 [size=16]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel modules: ata_generic, pata_acpi, ide-pci-generic
00:03.3 Serial controller: Intel Corporation Mobile 4 Series Chipset AMT SOL Redirection (rev 07) (prog-if 02 [16550])
Subsystem: Lenovo Device 20ec
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 1830 [size=8]
Region 1: Memory at fc024000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: serial
00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
Subsystem: Lenovo Device 20ee
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 29
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fc025000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 1840 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable+
Address: 00000000fee0300c Data: 41c1
Capabilities: [e0] PCIe advanced features <?>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1860 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1880 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 18a0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at fc226c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
Subsystem: Lenovo Device 20f2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fc020000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 0, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4169
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f4300000-f43fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 1, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4171
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=0c, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 00000000f4000000-00000000f40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 3, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4179
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=14, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 00000000f4100000-00000000f41fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 4, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4181
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 18c0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 18e0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1c00 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fc227000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=15, subordinate=18, sec-latency=32
I/O behind bridge: 00005000-00008fff
Memory behind bridge: f4800000-f7ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f3ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Lenovo Device 20f4
00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03)
Subsystem: Lenovo Device 20f5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: iTCO_wdt
00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Device 20f8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 28
Region 0: I/O ports at 1c48 [size=8]
Region 1: I/O ports at 183c [size=4]
Region 2: I/O ports at 1c40 [size=8]
Region 3: I/O ports at 1838 [size=4]
Region 4: I/O ports at 1c20 [size=32]
Region 5: Memory at fc226000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Mask- 64bit- Count=1/16 Enable+
Address: fee0300c Data: 4199
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] PCIe advanced features <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
Subsystem: Lenovo Device 20f9
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fc227400 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c60 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. Device e020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at f4300000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP+ BadDLLP- Rollover- Timeout+ NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-ff-fe-22-55-88
15:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba)
Subsystem: Lenovo Device 20c6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f4800000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=15, secondary=16, subordinate=17, sec-latency=176
Memory window 0: f0000000-f3fff000 (prefetchable)
Memory window 1: 80000000-83fff000
I/O window 0: 00005000-000050ff
I/O window 1: 00005400-000054ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
15:00.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04) (prog-if 10 [OHCI])
Subsystem: Lenovo Device 20c7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f4801000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
15:00.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21)
Subsystem: Lenovo Device 20c8
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f4801800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
15:00.3 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc
15:00.4 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 11)
Subsystem: Lenovo Device 20ca
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f4802000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
15:00.5 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 11)
Subsystem: Lenovo Device 20cb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f4802400 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

Time capsule 4th gen firmware 7.6.1 and Windows 7 Home Premium

Hi I have a Time capsule 4th gen firmware 7.6.1 and Windows 7 Home Premium and every time I try to copy a large file from the TC to my Windows 7 laptop the TC crashes. The time capsule disk dissapears from the network and the wireless is still on but with limited connectivity for everyone including the macs connected to the same network. On the contrary, I can copy any files to the TC. No problem. I've tried all the suggestions. Lmcompatibilitylevel 1, disable 128-bit encryption, and disabled windows search. No luck! Any other suggestions?

My previous reply: red herring. The problem didn't occur again right away, but eventually it did. Completely repeatable: start copying a 100GB file off the Time Capsue to the ThinkPad, and the entire wi-fi network goes down; nothing to do but pull the plug on the TC and restart it.
I have tried several different versions of the Intel wi-fi driver under Windows 7 and 8 -- same problem in all cases.
At least one other thread describing these same symptoms points to the firmware as the culprit (https://discussions.apple.com/thread/3582780?start=0&tstart=0). I have just downgraded the TC firmware from 7.6.1 to 7.5.2 as suggested; so far so good.

T430u and Windows 8 Problems

Hi everyone,
Really need some helps here. I bought a T430u , and to be honest, i'm rather dissapointed with this. My keyboard was dead in a matter of weeks, so i've just get it back from the sevice centre. And now I have another problems:
1.Cannot wake up from sleep
I've read on another sites that I have to disable expresscache and quick start, but then it'll make the ssd caching useless isn't it? And yet after I uninstall expresscache and disabled quick start, it still doesn't solve my problem. Now it'll wake from sleep but will crash and restart.
2.Glitchy trackpad
On some occassion, the trackpad just stop working for 1 - 5 minutes. And then it'll work again. Now I mainly use mouse, but seriously...
I've upgraded all the lenovo driver and windows update too. But it doesn't solve anything...

Hi centraldogma,
Welcome to Lenovo Community. I'm assuming that the system is still under warranty. I would suggest calling Tech Support to see if they can help you troubleshoot the problems. If that doesn't help perhaps they can advise about the last option of returning the system.
ThinkPad: T530 / X1 Gen 2 / Helix - Yoga: Tablet 2 Pro (Win) / Yoga 3 Pro
If you find a post helpful and it answers your question, please click the "Accept As Solution" button.
Lenovo Advocate ~ I am not employed by Lenovo or Microsoft. I am a volunteer.
Microsoft MVP - Consumer Security
SpywareHammer

Intel Matrix Storage Manager disables Windows Update and Windows Validation on Windows 7 64-bit

I have a Lenovo ThinkPad R61 8918CTO on which I did a clean install of Windows 7 Ultimate SP1 (64-bit) on a new Seagate Momentus XT 750GB drive. The installation was trouble-free, as were all of the post-install Windows Updates.
Then I installed ThinkVantage System Update 4.03 and used it to install most of the available Lenovo updates. Big mistake. I'll spare you a detailed account of the hours I wasted troubleshooting, rolling back to previous restore points, and doing more troubleshooting, but it turns out that installing Intel Matrix Storage Manager driver v. 8.9.2.1002 caused Windows Update and Windows Validation to fail.
Symptoms: Windows Update control panel can't check for updates and reports that the Windows Update service isn't running when it actually is. Online Windows Validation fails and the standalone Windows Validation utility won't install. Microsoft programs that require a validated copy of Windows (e.g., Microsoft Security Essentials) won't install.
Solution: Roll back the driver for the relevant SATA controller to the previous driver.
I've reinstalled ThinkVantage System Update 4.03 and hidden the proposed Intel Matrix Storage Manager update; since then, I've used it to complete my Lenovo updates without issue.
I hope this post will help other people with this problem find the solution a lot faster than it took me!

This happened after installing a new advanced format drive with 4k-byte sectors, I'd guess. If the storage driver doesn't report the physical sector size to Windows, update fails.
I just ran across this myself (again) putting Win 7 on a T400.
I don't know why this is still going on. It may be that the update lists for older machines still have pre-AF-drive drivers listed.
FYI, another fix is going to the Intel site and installing the latest Matrix Storage Manager AHCI driver. This may be more desirable than rolling back to an older driver in some cases.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Memory Leak Lenovo X201 and Windows 8

Hi,
I'm having a memory leak issue with my X201 and Windows 8. My system starts almost without memory, taking 6.7 of 7.8 GB RAM.
More people seem to have the same problem:
http://answers.microsoft.com/en-us/windows/forum/windows_cp-windows_programs/windows-8-rtm-memory-le...
I have installed the available beta drivers but they don't help. Any advice?
Spec:
- Windows 8 Enterprise
- Intel Core i7-620M Processor (2.66GHz, 4MB L3, 1066MHz FSB)
- Genuine Windows 7 Professional 64
- Genuine Windows 7 Professional 64 US English
- 12.1" WXGA LED Panel, 2x2 UltraConnect II antenna; with Camera and Wireless Broadband Upgradeable
- 8 GB PC3-8500 DDR3 SDRAM 1067MHz SODIMM Memory (2 DIMM)
- Keyboard UK English
- TrackPoint with Fingerprint Reader
- 128 GB Solid State Drive, Serial ATA
- 5-1 Media Card Reader and Modem
- ThinkPad X200 Series 9 cell Li-Ion Battery (up to 5 hours life)
- Country Pack United Kingdom with Line cord & 65W AC adapter
- Bluetooth w/ antenna
- Intel Centrino Advanced-N 6200 (2x2 AGN)
- Integrated Wireless Wide Area Network upgradable

Does Windows 8 manage memory differently?

Problem to come back from sleep mode in Lenovo Thinkpad T400 using Windows XP

Problem to come back from sleep mode in Lenovo Thinkpad T400 using Windows XP. Each time closing the T400 lid and try to make the laptop into a sleep mode for some time, it does not properly come out of sleep mode. Login screen is able to see when opening the lid for the first time, but it only seen for a while before then a black screen on T400 Thinkpad appears. Sometime the hard drive activity can be shown also. And then, to come back I had only one option to hard re-boot.
I tried Fn+F4 and power button once to come back but no use.
Please provide me some solution for this?
Thanks in Advance.

oh sorry and its been closed inbetween uses. When i open it the keyboard doesn't light up and it makes no sound.

T43 IBM Thinkpad, I installed Windows XP pro on a new harddisk, found no netowork

T43 IBM Thinkpad, I installed Windows XP pro on a new harddisk, found no network, so installed drivers for the chipset and network. Still no way to go on inernet.
Folloing drivers i installed from following site. What do I do now:
http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?&DocID=HT035703
Oss50w – chipset driver
7ora09ww – Ethernet driver
1ywc54ww – wifi driver

Hi guys and thanks for your help. Yes, after authenication and working on this Windows partition, I have less than 3GB space. Also, I cannot drag and drop files from desktop, like a text file into the Windows partition. Says it doesn't have permissions to drop files.
It looks like now I will in fact have to start from scratch and repartition the HD but put in a minimal 12GB or so into the Windows partition. Also, I tried to name the Windows label, but it's locked and under get info, it says the Windows partition is read only, ownership grayed out and says it is NT coded format. Shouldn't that be MS-DOS or FAT 32 automatically?
I have to tell all of you that this is getting time consuming, too complicated and when I get my own ProBook, I have no desire to install VISTA or MS whatever. Plus, we have to still do the MS security pack updates and install virus software for the Windows partition, isn't that correct?
Is there a step by step link here like a BootCamp/Windows XP Pro installation tutorial so I can move a bit faster on my next attempt?
Thanks SteveB

Thinkpad X1 and Windows 8

Similar Messages

Maybe you are looking for