Third Party Syslog on Windows LMS

Fortunately, I’ve previously been referred to the following whitepaper here with regards to installing a standalone syslog daemon on an LMS server.
However, I’m wondering if anyone has successfully implemented the local mode solution on a Windows instance of LMS?
If so, what edition of syslog-ng did you use?
Or alternatively, has anyone successfully installed another syslog receiver on a Windows LMS server that was able to forward messages to both internally to LMS and additional NMS hosts whilst maintaining the original source host details?
Thanks for any feedback.

You added the tag, lms2.6. In LMS 2.6, the only supported syslog server is the crmlog server which ships with LMS. Not even syslog-ng was tested. The syslog-ng support will require LMS 3.2. As for setting this up, I have only done it on Solaris.
It might be easiest to install Cygwin on your server, build syslog-ng under Cygwin (with spoofing enabled), then use the Cygwin syslog-ng binary. Finding a Windows native binary, or trying to build it with Win32 (if even possible) would probably be too much of a hassle.
Please support CSC Helps Haiti
https://supportforums.cisco.com/docs/DOC-8895
https://supportforums.cisco.com

Similar Messages

Report export to third party syslog server

Hi all,
Is there a way to send the Cisco ACS secure server report to third party syslog server?
Example: for audit purpose, i need the data extract from Monitoring & Reports > Reports > Catalog > AAA Protocol
I trying by create new remote log targets, the IP is pointing to third party syslog server.
and at the logging categories > global, i apply the new create log collector to all logging categoires.
Am i doing it right?
please comment, thanks
Noel

Hi Yong,
Yes that's possible. You can use the web interface to configure logging category messages so that they are sent to remote syslog server targets
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/logging.html#wp1052741
ACS provides these preconfigured global ACS logging categories, to which you can assign log targets.
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/logging.html#wp1052549
Configuring Per-Instance Remote Syslog Targets
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/admin_config.html#wp1063768
Jatin Katyal
- Do rate helpful posts -

How Do You Generate a 2048bit CSR for a Third Party SSL Certificate for LMS 4.0.1?

Our site requires Third Party SSL certificates to be installed on our servers. We have an agreement with inCommon. I have to supply a CSR in order to obtain the SSL certificate.
My installation is on a Windows 2008 server and I had the self-signed CSR already but it is only 1024 bits. Is there someplace in the GUI or OS where I can change the encryption?

This is a shot in the dark, but since CiscoWorks is using (I believe) Tomcat as the web server, could you run keytool to generate the CSR?
http://help.godaddy.com/article/5276
You could also use an online CSR gererator such as:
http://www.gogetssl.com/eng/support/online_csr_generator/
The key (pun intended) is having the private key on your server so that when you get the signed certificate and install it (using sslutil) it will be usable.
Hope this helps.

Intune & Third Party Software Automatic Updates

Can Windows Intune ensure third party software such as Java, Adobe Reader, & Flash is updated? I at-least want an email when a PC has an out of date version of the above software. If Windows Intune can't do
this, any recommendations?
We're a small business that simply uses Windows Intune and Office 365. Recently a PC had a vulnerable/out of date version of Java and visited a compromised site, resulting in a nasty virus. Obviously I don't want this to happen again.
Update: I ended up using GFI Cloud's patch management to address the lack of automatic third party patching in Windows Intune.

That requires manually uploading patch files for third party software daily... I'm looking for something that can automatically update common third party software that cause major security concerns, or at-least notify me when they are out of date.

A third party app had crashed my iPad iOS and will not reset. It gives a pop up window and seems very fishy.

I have a pop up window that says:
http://ios-support.net
The page at I-Pad support says:
Warning IOS - crash Report
Due to a third party application in your iPad, IOS crashed.
Contact Support for an Immediate Fix
i incantation reset anything, it seems extremely fishy and I'm locked up and ant do anything. Has anyone had this happen?
<Post edited by Host>

Do not call the number.
Double tap the Home button, then swipe upwards on the Safari preview.
Go to Settings - Safari - Clear History.
Restart Safari.

How can I set up printing to queues on a Windows 2008 server directly from the iPad apps and not from third-party applications without using AppleTalk or Bonjour?

We have a Windows 2003/2008 server-based network with a dedicated print server which we would like to be able to print to over Wi-Fi. How can I set up the printers on the iPad without downloading a third party application such as Print Central or Print N Share? I want to just click the arrow and "Print" then choose the printer, which doesnt show up. I want to be able to use the existing TCP/IP-based network that we have to reach these queues, not having to install Bonjour or AppleTalk to reach them.
Thanks,
KMQ7

This would really be the "Holy Grail" right now. I think this a feature that every large organization requires. AirPrint works on a small scale, but is not really an enterprise class application. In addition it uses the Bonjour discovery process which is difficult in a large LAN WAN environment. For those that would remind me, I am aware of the enhancement link

Formatting music from windows to a mac using third party app

i used a third party app so that i could download music from a pc onto my os x formatted ipod. initially it worked when i moved the music into my itunes library on my mac, but for some reason now a lot of the tracks won't play and my computer freezes if i press play on any track that originally was downloaded onto a pc. is there a way to identify where the songs came from and then delete then from the library without going through each one a seeing if it will play and then having to force quit itunes because it freezes?

From what I know, windows will not recognize the complicated data of a mac formatted device; hence not recognizing it. Macs can recognize a windows formated ipod though, so if you decide to reformat it on windows, then you can use it on both computers. If you dont though, looks like you are out of luck, sorry.
Hope I helped.

WIndows 8.1 64bit, Windows Installers stalls with any install, updates or third party programs.

WIndows 8.1 64bit, Windows Installers stalls with any install, updates or third party programs. Third party program installations work if I restart in safe mode. Updates don't as they cannot be installed in safe mode and require normal mode.
Been happening for months now. Some installations after a long time finally proceed, others dont.
Already trying uninstalling antivirus (Bitdefender) with no result.
Thanks

Hi，
Could you check this issue under clean boot?
Also try this fix tool it repair corrupted registry keys.
https://support.microsoft.com/en-us/mats/program_install_and_uninstall
Regards,
D. Wu
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

WLC 5508 - EAP-TLS - Windows 8.1 Third Party PKI

Hello,
Does anybody know what could prevent a Windows 8/8.1 system to connect to a WLC via EAP-TLS? Windows 7/XP do not have any problems here.The radius server accepts the request, but WIndows 8 still tries to authenticate.
Software is updated to 7.6.120.0, I tried to setup timeout values, but no success at all.
Did anyone have similar problems with Windows 8/81?
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Starting key exchange to mobile 0c:8b:fd:eb:16:17, data packets will be dropped
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Sending EAPOL-Key Message to mobile 0c:8b:fd:eb:16:17
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Sending EAPOL-Key Message to mobile 0c:8b:fd:eb:16:17
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Reusing allocated memory for EAP Pkt for retransmission to mobile 0c:8b:fd:eb:16:17
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 mscb->apfMsLwappLradNhMac = 00:24:97:52:87:d6 mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 13
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 mscb->apfMsBssid = 00:24:97:70:9a:00 mscb->apfMsAddress = 0c:8b:fd:eb:16:17 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId =
0 mscb->apfMsLwappMwarInet.ipv4.addr = -1407817979
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1407817773 mscb->apfMsLwappLradPort = 10367
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Entering Backend Auth Success state (id=6) for mobile 0c:8b:fd:eb:16:17
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Received Auth Success while in Authenticating state for mobile 0c:8b:fd:eb:16:17
*Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 dot1x - moving mobile 0c:8b:fd:eb:16:17 into Authenticated state
*osapiBsnTimer: Jun 24 12:43:13.801: 0c:8b:fd:eb:16:17 802.1x 'timeoutEvt' Timer expired for station 0c:8b:fd:eb:16:17 and for message = M2
*dot1xMsgTask: Jun 24 12:43:13.801: 0c:8b:fd:eb:16:17 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 0c:8b:fd:eb:16:17
*dot1xMsgTask: Jun 24 12:43:13.802: 0c:8b:fd:eb:16:17 mscb->apfMsLwappLradNhMac = 00:24:97:52:87:d6 mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 13
*dot1xMsgTask: Jun 24 12:43:13.802: 0c:8b:fd:eb:16:17 mscb->apfMsBssid = 00:24:97:70:9a:00 mscb->apfMsAddress = 0c:8b:fd:eb:16:17 mscb->apfMsApVapId = 1
*dot1xMsgTask: Jun 24 12:43:13.802: 0c:8b:fd:eb:16:17 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1407817979
*dot1xMsgTask: Jun 24 12:43:13.802: 0c:8b:fd:eb:16:17 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1407817773 mscb->apfMsLwappLradPort = 10367
*osapiBsnTimer: Jun 24 12:43:16.801: 0c:8b:fd:eb:16:17 802.1x 'timeoutEvt' Timer expired for station 0c:8b:fd:eb:16:17 and for message = M2
*dot1xMsgTask: Jun 24 12:43:16.802: 0c:8b:fd:eb:16:17 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 0c:8b:fd:eb:16:17
*dot1xMsgTask: Jun 24 12:43:16.802: 0c:8b:fd:eb:16:17 mscb->apfMsLwappLradNhMac = 00:24:97:52:87:d6 mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 13
*dot1xMsgTask: Jun 24 12:43:16.802: 0c:8b:fd:eb:16:17 mscb->apfMsBssid = 00:24:97:70:9a:00 mscb->apfMsAddress = 0c:8b:fd:eb:16:17 mscb->apfMsApVapId = 1
*dot1xMsgTask: Jun 24 12:43:16.802: 0c:8b:fd:eb:16:17 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1407817979
*dot1xMsgTask: Jun 24 12:43:16.802: 0c:8b:fd:eb:16:17 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1407817773 mscb->apfMsLwappLradPort = 10367
*osapiBsnTimer: Jun 24 12:43:19.801: 0c:8b:fd:eb:16:17 802.1x 'timeoutEvt' Timer expired for station 0c:8b:fd:eb:16:17 and for message = M2
*dot1xMsgTask: Jun 24 12:43:19.801: 0c:8b:fd:eb:16:17 Retransmit failure for EAPOL-Key M1 to mobile 0c:8b:fd:eb:16:17, retransmit count 3, mscb deauth count 0
Any hint would be great .... Thank you...

Hello Dino,
thanks very much for your reply.
The client uses a machine-certificate, the PKI is not a microsoft one, but a third party PKI. The certificate is fresh and valid, the root-cert is installed and checked to be validated against it for the login.
Clock is correct too. The same setup works flawlessly in Windows 7 and XP.
EKU is set on the certificate (1.3.6.1.5.5.7.3.2)
I suspect the cert-setup itself, but don't get a clue where this might stuck...
Björn

Security settings change when rendered from third party Windows 2008 R2 server

We created a fillable PDF form in Adobe Acrobat and made it Reader extended. Opening the form on a local hard drive the security settings show that Signing: is Allowed. We can sign documents in the form with a signature pad.
After we upload it to a third party Windows server 2008 R2, and we later go to access the form, the server renders it back to us in Adobe Reader. We are unable to digitally sign documents in the form with a Topaz signature pad. We notice that although the form was originally created with the form being Reader extended the security settings change to Signing: Not Allowed.
How can we get the server to render the document back to us where we can digitally sign documents in the form?

The second file still shows the extended rights header is present (it's warning you about restrictions at the top of the dialog while also reporting the method is "no security") but the digital signature which grants those extended rights will be invalidated if *anything* in the file structure is changed. I suspect in this case that the server software is doing something to your file; it may be trivial such as adding an XMP tag, but it's enough to break the hash check.

Need help finding folder to load a third party web gallery in bridge cs4 on windows 7

I purchased a third party PayPal webgallery for cs4. I do not know exactly where to put this on my windows 7 program folders. On CS3 it used to go
in program folder>plugins etc but with bridge, I can't find the folder where it should live. Any clues please ??

Isn't there a manual or description coming with that plugin?

After upgrading to OS Mavericks, I realized that the Partition for Windows is gone. I have really important data on this drive without a back up. Is there any way I can get this data before reformatting. Is there any third party software for receiving the

After upgrading to OS Mavericks, I realized that the Partition for Windows is gone. I have really important data on this drive without a back up. Is there any way I can get this data before reformatting. Is there any third party software for receiving the data or any possible way? Money is not a limitation to this fix. Please help!!!

sure pretty simple. make a backup of your current settings
http://support.apple.com/kb/HT1766?viewlocale=en_US
then restore device from old backup you need pics off of
then import pics to computer
http://support.apple.com/kb/HT4083
you may need to save pics to camera roll first
then restore the new backup and sync pics back to phone via itunes
Peace, Clyde

In Windows XP I have lost control over third party cookies

I bought a refurbished computer with Windows XP. But now I have noticed there is no control over cookies in Firefox. In Windows Vista there was 'block third party cookies' there was 'state which websites to permanently block' or 'allow' and even then I was only using Firefox... Now there is nothing. On top of that none of the "cookies control" add-ons for Firefox seem to be any good at all. I don't know what to do!
Why would Firefox change with Windows XP?? I can see with IE of course but Windows operating system has nothing to do with Firefox, if you know what I mean.

Please review this information [[Enabling and disabling cookies]]

Executing system command (third party program) from extend script without showing console on windows

I am using following code on mac:
app.system("/path/to/external/executable &");
It runs external program in background (without showing console/terminal).
On windows I tried many things like:
app.system('start "" "/path/to/external/executable"');
app.system('start "" /B "/path/to/external/executable"');
And I was also trying to solve it using visual basic.
Unfortunately everytime I use app.system(...) then windows console is showed on the screen for half of the second, then it disappears and progrm runs in background. Is it possible to avoid showing console window? Maybe there is another way of executing third party program?

You can try to save a vbscript :
Dim objShell
Set objShell = WScript.CreateObject( "WScript.Shell" )
objShell.Run("""\path\to\external\executable"""), 0, True
Set objShell = Nothing
than just execute it from javascript:
var vbFile = new File("path to your vbscript file")
vb.execute();

Cannot view third party flash (windows 7)

I've been trying to check the box to enable me to allow third party content but it will not check no matter what I do.
I've seen people post about this before, but the other posts were from users with different operating systems. I'm running windows 7 with firefox 3.6.12 and adobe flash 10.1
Please help..

Delete the 'Flash Player' folders at %APPDATA%\Adobe and %APPDATA%\Macromedia and try again. (Type or copy/paste these addresses into the Windows Explorer address bar.)

Third Party Syslog on Windows LMS

Similar Messages

Maybe you are looking for