Third Party Video Camera Wants To Zoom

I use a Panasonic video camera connected via Firewire, when using iChat (4). Every few minutes the image it picks up of me zooms in, and then after a moment, it zooms back out. I have no idea what controls this, but it is driving me nuts.
Any thoughts what might be going on and how I can solve this problem?

Hi,
Some DV Camcorders have demo modes.
Some of these include showing you all the editing whizzy things but this sounds like it is showing you other features.
Check it is not stuck in a Demo mode.
9:09 PM Sunday; April 26, 2009

Similar Messages

Adding third party video card to P700 - no power connectors? New Power Supply Question...

Hello,
I have a new P700 30A90012US with a 650W PSU and that didn't come with a video card. I am planning to use it as a DAW and for occasional gaming via a dual boot.
I wanted to put in a third party video card like a nVidea 970 but there aren't ANY connectors for video cards that I can find inside. The monitor I have is a 3440x1440 monitor. I have ordered a second 2609 Processor and RAM from Lenovo and have the following questions:
Once I install the second processor, how much wattage for a video card is available to me?
I understand that the 3rd party video card isn't supported but how do I attach power to it?
If it is required that I have to replace the 650 power supply with an 850, does it come with the required cable? I only see a 4 pin connector on the mobo that is unused (and I believe it is for additional hdd)
I tried searching but I am at a loss.
Thanks,

Your config isn't really power hungry (and the 85W CPUs help a lot). Though technically outside of the official spec, I think you could easily go to a 225W card for graphics if you had the connectors available to support it. I'll double check the current when I get a chance, but it's probably really low risk if you want to convert your single 6-pin connector to dual 6-pin or a single 8-pin (via a dongle) to get to 225W TDP if you wanted to.
The PSU design is very modular, but unfortunately it's the aux power cable drops that kept it from being an easy field upgradable part. I always recommend that people buy the larger PSU if they ever think they'll be doing any upgrades in the future just to make sure they are covered.
And like I said if you're comfortable working inside the system, it's not impossible to upgrade that cable drop on your own if you want to go up to the 850W. You'd have to get the cable and PSU, but after that it would require removing the motherboard and PSU, cutting some cable ties and routing the new cable, then getting everything routed correctly such that the motherboard reinstalls cleanly.

Third party Video conference device conferencing with Cisco SX80

Hi ALL,
We have Cisco BE6K (Call Manager 10.5), CTS-SX80-IPST60-K9, DX650, 7861, 8861 IP phone, Cisco 2901 Voice Getaway, 3750 Switch and ASA. internet was connected on ASA. SIP connectivity (For DID) connected to Cisco 2901 Voice Getaway.
I need to know cisco best practice and implementation guide on below question:-
1. How Third party Video conferencing units (LIFESIZE and Polycom) can conference and call with Call Manager IP Phones and SX80. Third party device will not register on MY CUCM.
2. We have two site. On Sit-1 has own Call Manager 10.5 and Site-2 has own Call Manager 8.X both are reachable. Now How they make a call?
Thanks
Gazi Afzalur Rahman

HI Ayodeji,
Thank you for valuable update.
1. On B2B solution :-
a) Are Third party device needs to register on CUCM or not. What the B2B solution says because that device not register on CUCM?
b) Which connectivity i need Internet and SIP or Only Internet?
c) On other site are they need SIP connectivity or Internet ?
2. Sip trunk between the two clusters are we need SIP connectivity on both site or need only reachability? On this scenario are we need VOICE RT because we have different data connectivity router for both site.
Can You refer any CVD guide of implementation ..
Thanks In Advance
Gazi Afzalur Rahman

Third Party Nikon Camera Contol Software and Lightroom 4?

Hello Everyone
I am currently shooting tethered, from a camera stand, with a Nikon D90. My images go into a a specific directory. I then import them into Photoshop Elements 10 Organizer. I would like to do everything in one step.
Lightroom 4 lacks the camera control features that are essential for my current task. I have to have Live View and I need to see the image immediately after it is shot. It is also important to be able to change the camera settings from my computer, primarily F Stop. Is there a way to link Lightroom 4 with a third party camera control program such as Nikon Camera Control Pro 2 or something similar. There are several programs that give me adequate camera control.
Thank you for your help and suggestions.
Roger RCG1953

the third party 2 in 1 Camera Connection Kit
Is this really the actual name of it?

Third party image viewer wanted

My company don't want to invest manpower in developing a good and stable image viewer. Can anyone suggest a good third party solution to present pictures (tiff,jpg etc...) and maybe other documents in a viewer component. I couldn't find a good comparsion of the available tools...
Thanks in advance.
TT

An Acrobat specific user forum may not be the optimal place to ask about the why-n-whatfore of a third party software.
Perhaps the application you are using has a vendor support site or user community?
Be well...

My video camera is automatically zoomed in when i open it. How do i fix this?

I am using iPhone 6 and i had updated it to the iOS 8.2. I started using its camera and video camera until one day when i opened the videocamera, it was automatically zoomed in. I tried to zoom out but it didn't work. When i switched to camera, it returned to its normal zoom again, that is, without it zooming in. I tried restarting my phone and it worked. But when it happened again, i did the same resolution but the problem was not fixed. Please help.

Are you sure the account is checked for new mail?
A .Mac type account is really an IMAP type account so any mailboxes stored on the server (under the .Mac account icon in the mailboxes drawer) are automatically synchronized with the server when first launching Mail and connected to the internet if the account is enabled under the Advanced tab for the account preferences.
I have 3 POP type accounts, a .Mac account and 2 IMAP type accounts. As a test, I deselected "Include when automatically checking for new mail" for all accounts and then quit and re-launched Mail. None of my accounts checked the incoming mail server for new mail but all server stored mailboxes for my .Mac account were synchronized with the server.

ThinkStation P700 - adding a third-party video card: supplementary power connectors?

Hi all,
I have recently purchased a ThinkStation P700 to replace my ageing setup and hopefully serve me for many years to come - It has not yet arrived (that's a different story altogether...).
I have a bit of a dillema regarding the video card I purchased for it. For my work I need CPU, much less so GPU, and especially not a Quadro. So for pure pleasure I added a GeForce GTX Titan Black (yes, I know that Lenovo will will not provide support for stability issues caused by this, etc, etc). I have the card already - here's my problem:
The card uses external power - it has one 8-pin and one 6-pin PCIe power connector on top of the board. With adapters I can get this to three 6-pin or multiple Molex, etc. The motherboard and the PSU in the P700 however, are so well designed and modular, that they almost seem too modular... I looked up the motherboard layout in the manual, and there are only 4-pin (?) connectors on the board, which are supposedly meant to be used with video cards. After a very long session with google it seems that hardly anyone has even heard of 4-pin power connectors for PCIe. Looking at pictures of the chassis available online, everything seems completely self-contained - the PSU slots into the board, and there are no free-hanging cables available whatsoever - am I right? Also pictures showing two full-size video cards installed, do not show power cables at all - maybe they're just cute marketing pics - the Quadros have power ports at the back - I simply can't see power cables in those pics, and the motherboard sockets are free. Obviously I know that the 4-pin, 6-pin and 8-pin are only combinations of 12V rails and ground.
So my questions are:
- are there any 6-pin or 8-pin connectors or Molex available anywhere at all?
- is there a spare part in the form of a 4-pin to 6-pin adapter? Is it perhaps bundled with the P700?
- how are the Lenovo-integrated video cards powered - surely with how thin the PCIE tracks are, they can't be powered only from the board - or can they?
- is this perhaps a joke on me / catch to make sure I only buy the pre-approved cards?
Thank you in advance.
Regards,
owczi
Solved!
Go to Solution.

Hi,
Now THAT was lots of info, and more. Much appreciated.
1. Power connectors - Indeed, Titan (Black) is 8 + 6 - so I'm happy with the info I got from you guys so far.
2. Specs listing dual K6000 - this site (looks like a Lenovo site?): http://thinkstation-specs.com/thinkstation-p700/ - there's a PDF with the same info there. This even says 3 x K6000 in SLI. I mean the board physically has three long slots, and three of those 4-pin ports that according to the manual have something to do with power - but I can't see this working. The psref site says K6000 (one) but the online shop will not let you configure the P700 with one - unless some other options preclude it and that's why I didn't see it.
3. CPU - I have no need for dual CPUs right now so I went for a single E5-1650v3 - I bought the P700 not P500 just so that I have an upgrade option, I may not use the second socket in the end but who knows.
4. Yes, I got the 9364-8i card (plus supercap module) - is this a Lenovo-specific model? Hard to find anything about it online - or is it just new? The blind mate assemblies are good news. So not much different to server-type drive caddies in the end - minus hot swap maybe.
5. Regarding the drives - are the internal (not front - the bottom ones) drive bays also referred to as FLEX bays? Theye are four of them and I intend to use four drives only ( 2x 240G SSD RAID 1 pre-installed + 2 x 4TB RAID 1 mine) - so why do I need to stick two drives into one tray - or is this just if I wanted to maximise the number of drives usable? The 4TB drives are HGST UltraStar 7k4000 - standard, full-thickness 3.5". The SSDs are Lenovo's whatever - the "240G SSD" option - Intel I think, looking at psref.
6. Shipping delays - see, this is the sort of concrete info I was looking for and I'm immensely thankful for this.
The rest is a rant/vent someone from Lenovo should read.
So - in the meantime I started giving Lenovo UK & Ireland some abuse over Twitter (sorry, but well deserved IMO) - name and shame does wonders in the age of social media.
Had I been told something along the lines of "sorry, new product, build issues, we're working on it", I would have (reluctantly) shut up and waited for my turn. I'm an engineer myself, supporting systems where minutes of downtime cost hundreds of thousands, and working with vendors a lot. Delays and issues happen, when an engineer tells me there's an issue and I don't sense B/S, I accept it.
If the product is still wet, don't open it for orders or say it's pre-order. I can see that in the US the P700 is still "coming soon", in the UK it suddenly became available so I ordered it.
However, the process here is broken: Lenovo UKI (is it the same in the US?) uses DigitalRiver as the shop/shipping/support front end. That's all well and good, outsourcing does work in some cases. BUT there's no way to view the estimated shipping dates - only customer support can retrieve them from Lenovo (why can't they just make this info available online - to avoid people over-relying on it?)
The Customer Support cannot tell me anything. The only thing they can do is pull an estimated shipping date out of some magic 8-ball. Two weeks pass since order, I ask CS, they give me Dec 18th shipping date. I call them on the 22nd, on the call with me they tell me it's now magically the 22nd. Come on...
Throughout all this time I got zero notifications about anything happening with the order, as far as the Lenovo site is concerned, it's "in process" since Nov 29. Do you know that when I order a Domino's pizza from round the corner, I get a live animated progress screen from order through assembly, baking, QA and delivery?
Yes, it costs money and yes, businesses pushing more consumer grade disposable **bleep** than anything else, don't care about customer loyalty anymore, but why don't you at least show the high-end customers some respect - why can't you implement a tracking process for custom builds, or at least keep people updated?
I specifically chose the Lenovo P-series because I have no doubt that they are the best on the market. Dell don't offer the same storage options and customisation options. HP are not up there either. Fujitsu Siemens make great machines with straightforward hinged doors and drive bays behind them, but they have a **bleep** distribution model i.e. via specialised resellers only, making it near-impossible for a regular mortal to buy - at least in the UK. So the sad thing here is that I will most likely just wait and you'll still get my money - but if the official channels keep treating me like an idiot, I am very tempted to take my $4k somewhere else.

Third Party Video Modules

I have an MCU with EMP, and all works fine. I would like to have a "higher end" camera for conference rooms etc. Ideally, it would also be able to work with a projector on a laptop, incorporating IP Communicator. Any ideas? Thanks

I just got a resolution from TAC on this issue.
These settings fixed the issue for 8945 and Jabber clients.
Preferred video codecs:
Choice 1 : H.264
Video codec settings:
Video resolution: CIF (352x288)
Frame rate: 30fps
Video Bitrate: 384
Video packet size: 1400 Bytes
Advanced RTP settings
H.264 payload type (1): 103
H.264 payload type (1): 124
H.263+ payload type (1): 97
Polycomm Compatible; Yes

My video camera will not zoom since installing iOS 7

Since installing iOS 7 on my ipad retina the video will not zoom during recording. In iOS 6 I could zoom the recorded video.
Any answers please.

Me too. Since upgrading to iOS7, Siri gives me "I'm sorry about this..." MOST of the time. Fine on weather; 100%, but if I ask to send someone a message or text, it 'thinks' for a long time and eventually says "I'm really sorry about this". My friend's iPhone 5 works instantly, side by side; completely different yet same version of iOS and all settings same. I've tried everything: hard resets, switching Siri on and off, reset net prefs and all settings, even tried a different sim, everything I can think of, but Siri is still slow, unresponsive and 100% fails on complex tasks. Anyone any more ideas?

Third-Party SIP camera

I've connected an IP security camera that has SIP phone capabilities to our CM 5.1. All the phones are Cisco SCCP phones. The camera is fully registered and can call any extension in our calling space. However when I try to call the camera from the phones, I get a fast busy. I'm not sure if it's a CM config issue or I missed something on the camera. What am I missing to get the SCCP phones to call SIP devices?
Thanks!

For the point to point call they setup normally using IP addresses. See of the port numbers for the camera are opened from SCCP side.

Video call from Cisco 8945 SCCP to Polycom VVX 1500 Third party Sip Phones between intercluster trunks is not working

Dear All,
We have two cucm Clusters in Different Locations between that clusters i created
Inter-Cluster Trunk (Non-Gatekeeper Controlled) Now all are working fine Between Clusters
audio calls & Video calls between sccp 8945 phones , but iam facing a Problem with third party
Video Phones (Polycom VVX 1500 ) Third Party SIP Phones located in second cluster, From 1 st cluster cisco 8945 Video
phone to 2nd cluster Polycom Video phone all calls are works for voice call only, but no video ,
Please Suggest me Solution.
Thank you,
Sriman

Try setting up a SIP trunk between the two clusters and set a route patten just to the VVX 1500 and check how that goes.
From memory inter-cluster trunks are a H.323 like protocol which might have video inter-op issues with the Polycom device.

My new camera wants osx 10.4 0r more to upload videos can i download this upgrade

my new video camera want osx 10.4 or larger can i download this upgrade from apple store?

prkrgrp wrote:
osx 10.4.11
intel core 2 duo
1 gb 667 mhz
Run Software Update to get to the most up-to-date version of 10.4.x. You will find Software Update by clicking the Apple Symbol in the upper left of your screen and then clicking Software Update.
However you have a pretty old machine and you cannot access the Mac App Store on 10.4.x, you need at least 10.6.6 to do so. Look at the minimum specifications the camera you are considering has then compare with your machine's specifications. If you are not sure what the specs are on your machine open System Profiler (Applications- Utilities - System Profiler) and you can find the specifications.

Can an external video camera connect through a Mac to Apple TV?

The business has a conference room that they would like use for video conferencing. They have a flat screen TV and asked if they could mount a video camera above the TV, that is connected to a MacBook Pro or MacMini, and use the external camera for video conferencing. They wouldn't be using it with FaceTime, it's a third party video conferencing program. They just want to know if they could mirror the video conference call through Apple TV when using an external camera?

Hi,
Thanks for your assistance, but I spent quite some time researching this before posting, and the post you link to (which I've already read) doesn't actually answer my question, that person is asking about his wireless speakers receiving individual sound channels through airplay. Other discussions, which I've also looked at, seem inconclusive.
I was really posting in the hopes of finding anyone who had personal experience of trying to play a fullscreen, 5.1 surround video file using airplay mirroring from their mac to their Apple TV, and if they received 5.1 sound.
Thanks again for your help though.

Flip Video camera & problems with iMovie 08

If you are having problems with iMovie and Flip Video, here is the Flip Video email response on 27 May 2008:
Hello,
Thank you for your response.
We are not authorized to support third party applications, which is why we do not provide specific instructions regarding iMovie or any other third party application. We only support the Flip and the Flip program, while offering suggestions regarding other programs.
The Apple website also offers Perian as a workaround regarding audio on the Tiger operating system with the latest QuickTime. The latest QuickTime upgrade didn’t allow for audio playback of AVI files, which is why Perian is now offered as a work around by us and by Apple.
It seems as though you are able to playback your videos, as well as use them in outside applications. If this is not the case, and you are having issues using your Flip video or your Flip video program, feel free to contact us further.
Thank you,
Consumer Support
Pure Digital Technologies, Inc.
This is my email to Flip Video on 26 May 2008:
My MAC Updater downloaded the new QT 7.4.5 on 5 Apr 2008. I have been making movies in iMovie, and then posting them to YouTube. In the beginning I uploaded the movies as MOV files but soon discovered AVI files (larger file and longer time to upload) had more clarity when viewed on YouTube. Once the new QT 7.4.5 downloaded all my AVI files had picture, but no sound! I downloaded the Perian component as posted in QT discussions. The sound returned to the AVI files. However, when I Exported an AVI movie from iMovie the picture quality was worse than the MOV movie. There is something wrong with the new QT 7.4.5 when working with AVI, my AVI movies look terrible. These AVI files were all downloaded from my Ultra Flip Video camera with Flip’s codec 3vix. Flip is aware of this problem and acknowledged it last Friday. Flip says Apple is aware of the problem.
My MAC PowerPc G4 has performed well in the past two months when working with the Flip Video camera. So, at Flip Video’s suggestion I upgraded the operating system to OS 10.5 from OS 10.4.11. Flip Video says their camera works with OS 10.5. Once OS 10.5 was uploaded I soon discovered that iMovie 08 would not operate on my PowerPc G4, 1.86 MHz. The speed requirement for iMovie 08 is 1.9 GHz.
At this point of “spinning my wheels for nearly a month” with this Flip Video camera, I decided to purchase a new iMac. On May 2, 2008, I walked out of the Apple Store in Walnut Creek with the new iMac 20-inch: 2.66GHz. Now the Flip video camera should work and all my video problems solved. However, this was not to be.
When I attempted to Import Flip Video AVI and MOV files into iMovie 08 the files were “grayed out” and would not Import. None of my previous Flip Video files would Import. I tried making new Flip Video movies, they also would not Import into iMovie 08.
At another Apple Store, the tech suggested I download the previous version of iMovie HD. I did this and with hours of working through the different Export options I was able to create movies to post again on youTube. However, the picture quality of the newer iMovies has never approached the quality of my last post before QT 7.4.5 downloaded. Remember my problems started with QT 7.4.5. Well, my new iMac came with QT 7.4.1, I have not Uploaded QT 7.4.5 and won’t until Flip Video fixes this problem.
Examples of my Flip Video movies can be viewed on youTube at: sffoggydays. The last video with excellent picture quality was posted 6 Apr 2008 titled “A Day at the San Francisco Zoo, Chapter Nine, L-Taravel Ride to BART.” This video was made in iMovie and Exported before QT 7.4.5 downloaded. All the youTube Flip Videos made after 6 Apr 2008 have poor picture quality.
It is time for Flip Video camera to stop “passing the buck” to Apple. When manufactures of operating system such as Apple and Microsoft create newer and upgraded systems, it is the responsibility of the manufactures of applications to redo their programs for operating on the new systems. Here is where Flip Video is not accepting this responsibility to Mac users of their camera. The Flip Video application/codex/drivers need to be updated in order to fix the following problems:
- No sound on AVI files in QT 7.4.5
- No Import of AVI and MOV files in iMovie 08
- Poor picture quality for youTube in Export of iMovie HD
I like my Flip Video camera, want to continue making movies for youTube, and recommending the camera to others. The Flip Video camera people need to fix these problems for Mac users.

Hi!
I agree 100%!
I also purchased the Flip Video - was thrilled to see that they worked with Apple computers. I made several movies with it when I had my PowerBook G4. I went on a great vacation & took several once in a lifetime videos. Got home & couldn't wait to put them in my iMoive -06, burn them on my iDVD and sent them to several family members & friends. Before I got the chance, I had my system updater tell me that there was a new version to QT. GREAT, I thought, just in time for my vacation videos. Like you, after the QuickTime upgrade, I got video, but no sound. I was SICK about it! I also wrote to the Flip people & got a response somewhat like yours. I left the videos on my Flip which left no room for any others, but I didn't want to take the chance of losing them. After reading from Flip that it would work with OS 10.5 system, I talked myself into getting a new MacBook Pro. Came with all the upgrades iLife -08 and the OS 10.5.2 OK...finally, after months of stressing over losing the vacation videos, I had all I needed to save them! Of course the $2,000.00 price tag hurt a bit, but I deserve a new computer.
Well...I STILL can't get my priceless vacation videos edited and burned! I tried downloading 2 different programs that were supposed to help convert my Flip movies to something that would work, but they haven't. I could get it to work on my desktop with QT, but what good is that?? I want to make DVD's to send to others & save for my grandkids (if I ever am lucky enough to get some!)
I'm TOTALLY disgusted & feel I've wasted my money on the Flip Camera (that at one time I loved & was seriously considering giving them as gifts) the $2,000.00 on a new computer (that even though I do deserve, didn't REALLY need one yet!) AND I still have vacation videos that I can't share!
So... I agree! Flip should honor their word that is printed on the box & MAKE it work with all Apple computers. Surely they can find a fix!
TOTALLY disgusted with the whole FLIP/APPLE mess!
Oh, Flip also said they 'heard' that QuickTime Pro would work with iMovie -08 - although they haven't actually tested it themselves. NO THANKS!!! I've got WAY too much money invested in this stupid Flip camera!

Flip Video camera & problems with QT 7.4.5

If you are having problems with QT 7.4.5 and Flip Video, here is the Flip Video email response on 27 May 2008:
Hello,
Thank you for your response.
We are not authorized to support third party applications, which is why we do not provide specific instructions regarding iMovie or any other third party application. We only support the Flip and the Flip program, while offering suggestions regarding other programs.
The Apple website also offers Perian as a workaround regarding audio on the Tiger operating system with the latest QuickTime. The latest QuickTime upgrade didn’t allow for audio playback of AVI files, which is why Perian is now offered as a work around by us and by Apple.
It seems as though you are able to playback your videos, as well as use them in outside applications. If this is not the case, and you are having issues using your Flip video or your Flip video program, feel free to contact us further.
Thank you,
Consumer Support
Pure Digital Technologies, Inc.
Here is my email to Flip Video on 26 May 2008:
My MAC Updater downloaded the new QT 7.4.5 on 5 Apr 2008. I have been making movies in iMovie, and then posting them to YouTube. In the beginning I uploaded the movies as MOV files but soon discovered AVI files (larger file and longer time to upload) had more clarity when viewed on YouTube. Once the new QT 7.4.5 downloaded all my AVI files had picture, but no sound! I downloaded the Perian component as posted in QT discussions. The sound returned to the AVI files. However, when I Exported an AVI movie from iMovie the picture quality was worse than the MOV movie. There is something wrong with the new QT 7.4.5 when working with AVI, my AVI movies look terrible. These AVI files were all downloaded from my Ultra Flip Video camera with Flip’s codec 3vix. Flip is aware of this problem and acknowledged it last Friday. Flip says Apple is aware of the problem.
My MAC PowerPc G4 has performed well in the past two months when working with the Flip Video camera. So, at Flip Video’s suggestion I upgraded the operating system to OS 10.5 from OS 10.4.11. Flip Video says their camera works with OS 10.5. Once OS 10.5 was uploaded I soon discovered that iMovie 08 would not operate on my PowerPc G4, 1.86 MHz. The speed requirement for iMovie 08 is 1.9 GHz.
At this point of “spinning my wheels for nearly a month” with this Flip Video camera, I decided to purchase a new iMac. On May 2, 2008, I walked out of the Apple Store in Walnut Creek with the new iMac 20-inch: 2.66GHz. Now the Flip video camera should work and all my video problems solved. However, this was not to be.
When I attempted to Import Flip Video AVI and MOV files into iMovie 08 the files were “grayed out” and would not Import. None of my previous Flip Video files would Import. I tried making new Flip Video movies, they also would not Import into iMovie 08.
At another Apple Store, the tech suggested I download the previous version of iMovie HD. I did this and with hours of working through the different Export options I was able to create movies to post again on youTube. However, the picture quality of the newer iMovies has never approached the quality of my last post before QT 7.4.5 downloaded. Remember my problems started with QT 7.4.5. Well, my new iMac came with QT 7.4.1, I have not Uploaded QT 7.4.5 and won’t until Flip Video fixes this problem.
Examples of my Flip Video movies can be viewed on youTube at: sffoggydays. The last video with excellent picture quality was posted 6 Apr 2008 titled “A Day at the San Francisco Zoo, Chapter Nine, L-Taravel Ride to BART.” This video was made in iMovie and Exported before QT 7.4.5 downloaded. All the youTube Flip Videos made after 6 Apr 2008 have poor picture quality.
It is time for Flip Video camera to stop “passing the buck” to Apple. When manufactures of operating system such as Apple and Microsoft create newer and upgraded systems, it is the responsibility of the manufactures of applications to redo their programs for operating on the new systems. Here is where Flip Video is not accepting this responsibility to Mac users of their camera. The Flip Video application/codex/drivers need to be updated in order to fix the following problems:
- No sound on AVI files in QT 7.4.5
- No Import of AVI and MOV files in iMovie 08
- Poor picture quality for youTube in Export of iMovie HD
I like my Flip Video camera, want to continue making movies for youTube, and recommending the camera to others. The Flip Video camera people need to fix these problems for Mac users.

Flip video ( I just bought one) makes AVI files (AVI is a container like QT is one) using 3ivX. All you need is the free Perian codec and you can playback, edit etc. Export the to a MOV container which doesn't reencode them and you should have usable files.
They have a valid point - they supply software and they have no obligation to make their camera work in iMovie. Reviews I have read say it works OK in IM6 vs. the iLife 08 version. Note that QT doesn't work natively with DivX, WMV and you don't see Apple saying they are obligated to fix Quicktime. They like their codecs and they don't care about others any more than Flip does.
You can always open in MPEG Streamclip and export them to a non lossy codec like Animation and use those new QT files as well. Or DV as another format option.

Third Party Video Camera Wants To Zoom

Similar Messages

Maybe you are looking for