This is my iphone 4 ECID: ********, now restore or update showing error code 1 what can i do now?
this is my iphone 4 ECID: ******, now restore or update showing error code 1 what can i do now?
From the article:
Error 1 means that your device or computer may have a hardware issue that's preventing the update or restore from completing.
1.Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
2.Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
3.Confirm that your security software and settings are allowing communication between your device and update servers.
4.If you still see the error message when you update or restore, contact Apple support.
Similar Messages
-
All of a sudden my iPhone 3GS gave me a message about setting "Location Services" I think? anyway, when it failed a few times, I was then directed to "restore" my phone. tried that and POOF!!!! could not be restored. Now have a cute little paper weight, but would like to convert it back to a phone. Any help?
Error 1 is a very bad Hardware Error of the Baseband Chip. There is no fix. If you have Warranty or AppleCare Coverage, make Genius Reservation and take iPhone to Apple for resolution.
-
My iPhone has crashed and i went to iTunes to restore it and after waiting for it to be restored it said "The iPhone could not be restored. An unknown error occurred (2006). Can anybody please help suggest what i should do now?
This error normally appears if you attempted to downgrade or modify your iOS. See here http://support.apple.com/kb/TS3694#error1015
-
when I do this steps thy give me a massege says " the iphone could not be restored . An unknown error accorred (3149) " . Can I get some help ?
Try using DFU/Recovery mode to restore
1. Plug iPhone 4 to computer
2. open iTunes
3. Turn off iPhone
4. Press home and power button for 10 seconds
5. Stop pressing the power. Button but keep pressing down the home button
iTunes should say the following; "iTunes won't be able to use your iPhone until you restore your device"
Then you'll have the option to restore and it should work, it has worked for me in the past -
Hi i'm trying to restore my iPod classic and it says that the iPod could not be restored. An unknown error occurred (1434) what can i do to fix this? Thanks
Error 1015: This error is typically caused by attempts to downgrade the iPhone, iPad, or iPod touch's software. This can occur when you attempt to restore using an older .ipsw file. Downgrading to a previous version is not supported. To resolve this issue, attempt to restore with the latest iPhone, iPad, or iPod touch software available from Apple. This error can also occur when an unauthorized modification of the iOS has occurred and you are now trying to restore to an authorized, default state.
http://support.apple.com/kb/TS3694#error1015 -
When i update my iphone 4s in itunes, it shows error 1. What can i do now?
When i update my iphone 4s in itunes, it shows "error 1". What can i do now?
That ususally indicates a hardware failure. Bring your phone into Apple.
-
For accident I uninstall creative cloud and now I want to installed again and it appears error code 86 what can I do know?
Belen Ochoa where are you receiving Error 86? During the installation process for the Creative Cloud Desktop application? If so which software firewall are you utilizing?
-
I have iphone 5s and i have error code 1009, what can i do?
I have iphone 5s and i have error code 1009, what can i do?
Make sure it's charged using a will charger. If it still won't turn on try resetting it (hold on/off and home buttons simultaneously for 10-15 seconds until you see the Apple logo, release and wait for it to restart).
-
HT4623 iPhone 4 will not restore and update. (Error 26)
My iPhone 4 will not restore and update on iTunes. Error 26. I have tried everything. Removing battery. Removing motherboard. DFU/Recovery Mode. No luck. Could it be hardware issue?
I have also tried different PCs and cables. I have tried iTunes 10.6.3 and even latest version. My iPhone is currently stucked in DFU loop.
-
Hi, my iphone 5 will not restore through iTunes. Error codes 2001 and 2006 appear. Please help.
Hi,
My iPhone5 will not restore through iTunes. Error code 2001 appears and once I received error code 2006. Please help?Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on)
If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software. If the errors persist on another computer and known-good USB cable, the device may need service. -
Help, my iphone is in recovery mode, and itunes shows error code 1
help me, please. my iphone 4 is stuck in recovery mode, and when trying to restore, itunes shows " error code 1, an unknown error occurred"
please help!!!me to ;/
[23:05:36.0982] [nand_part_core:INF@2289] first 2 pages of boot blocks written with copies of partition table
[23:05:36.0982] [nand_part_core:INF@3169] next 98 pages of boot blocks written with LLB image of size 150080 bytes
[23:05:36.0982] [nand_part_core:INF@3172] final 156 pages of boot blocks written with random data in full page format
[23:05:36.0982] entering update_gas_gauge
[23:05:36.0982] entering update_ir_mcu
[23:05:36.0982] looking for mcu nub...no entry from path!
[23:05:36.0982] TiSerialFlasher not supported on this platform. Exiting.
[23:05:36.0982] entering update_baseband
[23:05:36.0982] update_baseband: registering for progress notifications
[23:05:36.0982] create_baseband_update_options: Got imeisv: 16
[23:05:36.0982] baseband updater options = <CFBasicHash 0x17533030 [0x59b710]>{type = mutable dict, count = 7,
[23:05:36.0982] entries =>
[23:05:36.0982] 0 : <CFString 0xcf1e38 [0x59b710]>{contents = "SystemRoot"} = <CFString 0x1761cb70 [0x59b710]>{contents = "/mnt1"}
[23:05:36.0982] 5 : <CFString 0xcf1dc8 [0x59b710]>{contents = "DisallowFusiing"} = <CFBoolean 0x59b910 [0x59b710]>{value = true}
[23:05:36.0982] 6 : <CFString 0xcf1f48 [0x59b710]>{contents = "autoSetupEnv"} = <CFBoolean 0x59b918 [0x59b710]>{value = false}
[23:05:36.0982] 7 : <CFString 0xcf1e48 [0x59b710]>{contents = "DataRoot"} = <CFString 0x1761e8e0 [0x59b710]>{contents = "/mnt2"}
[23:05:36.0982] 8 : <CFString 0xcf1d98 [0x59b710]>{contents = "forceUpdate"} = <CFBoolean 0x59b910 [0x59b710]>{value = true}
[23:05:36.0982] 9 : <CFString 0xcf1f58 [0x59b710]>{contents = "disablePing"} = <CFBoolean 0x59b910 [0x59b710]>{value = true}
[23:05:36.0982] 10 : <CFString 0xcf1eb8 [0x59b710]>{contents = "IMEISwVersion"} = <CFNumber 0x17533010 [0x59b710]>{value = +16, type = kCFNumberSInt32Type}
[23:05:36.0982] }
[23:05:36.0982] update_baseband: querying baseband info
[23:05:36.0982] bbupdater: BEGIN: Querying info at stage first
[23:05:36.0982] bbupdater: BEGIN: Preparing first stage
[23:05:36.0982] bbupdater: Requested boot mode: kBBUBootModeNone
[23:05:36.0982] bbupdater: Creating transport, attempts remaining 5...bbupdater: FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater: powercycling modem
[23:05:36.0982] bbupdater: Creating transport, attempts remaining 4...bbupdater: FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater: powercycling modem
[23:05:36.0982] bbupdater: Creating transport, attempts remaining 3...bbupdater: FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater: powercycling modem
[23:05:36.0982] bbupdater: Creating transport, attempts remaining 2...bbupdater: FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater: powercycling modem
[23:05:36.0982] bbupdater: Creating transport, attempts remaining 1...bbupdater: FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater: powercycling modem
[23:05:36.0982] bbupdater: Creating transport, attempts remaining 0...bbupdater: FAILED(kBBUReturnIOError)
[23:05:36.0982] bbupdater: END(kBBUReturnIOError): Preparing first stage
[23:05:36.0982] bbupdater: END(kBBUReturnIOError): Querying info at stage first
[23:05:36.0982] send_bbupdate_status: sending baseband update status to host
[23:05:36.0982] update_baseband: calling CFNotificationCenterRemoveEveryObserver
[23:05:36.0982] update_baseband: bbupdater error: The operation couldn\U2019t be completed. (BBUpdater error 3 - Failed creating a communication transport to baseband.)
[23:05:36.0982] 0: RamrodErrorDomain/3ec: update_baseband: failed querying baseband info
[23:05:36.0982] 1: BBUpdater/3: Failed creating a communication transport to baseband.
[23:05:36.0982] unable to convert ramrod error 1004
[23:05:36.0982] restore failed with CFError:
[23:05:36.0982] 0: AMRestoreErrorDomain/ffffffff: failed to update device firmware
[23:05:36.0982] 1: AMRestoreErrorDomain/ffffffff: ramrod firmware update failed
[23:05:36.0982] 2: RamrodErrorDomain/3ec: update_baseband: failed querying baseband info
[23:05:36.0982] 3: BBUpdater/3: Failed creating a communication transport to baseband.
[23:05:36.0982] waiting for host to acknowledge final status received...
[23:05:36.0982] void AppleUSBDeviceMuxXXXXXXXXXXXXXXXXXXX(mbuf_t) received reset, closing 0x97b1e4d0
[23:05:36.0982] recv(12, 4) failed: connection closed
[23:05:36.0982] unable to read message size: -1
[23:05:36.0982] received NULL message from host, expected final status
[23:05:36.0982] attempting to dump restore log
[23:05:36.0982] writing log file: /mnt1/restore.log -
Trying to update to IOS8 stuck on restoring firmware, then showed error code
Tried updating my phone, and it kept getting stuck when it was "restoring firmware", now I cannot get my phone to even function.
Solved an issue like this on my iPhone 6 on Verizon by, get this, removing the SIM card, plugging the phone with its red iTunes death screen into the computer, and performing the "Restore / Restore & Update" now without the SIM, which worked fine and then slipped the SIM back in the phone and started using it.
This sounded too easy to be true and I tried it and it worked. Mine was locking up near the end of the restore every time while doing the firmware and I was going to take the phone back into the store when I saw a post stating that worked for someone and I am so grateful I tried it.
EDIT: Oops, old post. Sorry. -
HT201413 i keep getting error code-1 what can i do to get my iphone to work agian
hi i have a iphone 3gs from att i have no phone service but use it like a ipod but now it keeps telling me to restore it but when i do it gives me a -1 error code so now my phone will not go to the home screen and all it dose is plug in to itunes ...what do i do with out buying the apple care plan?
i have this too on my hp photosmart b210
no one seems to know how to fix it!! -
Error code -1303. what can I do to fix this?
My father bought a used ipod classic 80G 2 days ago. I hooked the ipod up to my itunes and restored it. As i was loading music to it, I realized that the music was not loading and I got a error code -1303. I restored the ipod again, same thing happened. I reformatted the ipod and then restored it again and now it let me add 6G's to it but it won't let me add more. Now i'm getting error code -53 and error code -1303. What is this and how can I fix it? Please help!
Since it is under warranty, bring it back to Apple store, and explain to them the issue.
But if it is too inconvenient to go there, then here is an earlier post which may help you, 2 possible solution.
Untick - enable Disk Use.
Network drive conflict - need to rename the iPod drive.
Have a nice day! -
I am trying to figure out why I cannot restore my Ipod touch 64, when I get through the whole restore it states "error code 1602". I have used the original cable that came with the Ipod and have tried it on two different computers. When I turn it on only the apple logo appears and nothing else happens. Please help
Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on)
If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software.
If the phone is stuck on the Apple logo, you can try a hard reset (deletes no info). Press and hold the power button and Home button until the phone turns off. Then try to power it up again.
Simply restarting your computer will not cause your iPhone to stop working unless there is a major issue with software conflicts on your computer... i.e.... corrupt iTunes installation.
Try disabling any security software you might have and avoid using and USB hubs or extenders etc.
If the hard reset doesn't work in getting your phone to boot up, then you'll have to do a restore of the device.
Maybe you are looking for
-
Is there a way to downdrade after installing Pro Applications updates 2010-2 and 2008-05? The updates seem to have broken my programs.
-
Xdo loader is not replacing the RTF template
Hi , I am using the below syntax to upload the RTF template. It has to replace the existing template. But it is not doing. java oracle.apps.xdo.oa.util.XDOLoader UPLOAD -DB_USERNAME apps -DB_PASSWORD $apps_pw -JDBC_CONNECTION $p_host:$p_port:$p_insta
-
File name font (web gallery output)
I am using CS4 with adobe bridge. I have created some web galleries and have selected the option to show the file name. This shows up just below the picture in the gallery. The problem is the font is too light to show up against my chosen backgrou
-
Microsoft.BDD.PnPEnum.exe is not a valid win32 application
Hi all, Im running into an unusual bug during my media based Win 7 32 bit light touch deployment. After the wizrad completes and it formats the drives right about the time its ready to inject the drivers i get an error E:\Deploy\Tools\X86\Microsoft.D
-
Application got locked when power failure(abnormal shutdown)
hi all,,, I am developing swings application where user needs to login by giving valid Uname and password(only one user at a time,multiple users not allowed) and im storing this data(Uname and pwd) and status(looged in/not) in xml,my app is working f