This Officejet 6500A is so noisy - both previous HP printers were quite. Sounds like a tractor

This HP printer I've owned - loved the others. The new Officejet 6500A is so noisy - it sounds like a tractor starting whenever it pulls in a new page to print. YUK Any suggestions ??

The printer sounds defective, my Officejet 6500 was as quiet as my other HP inkjet printers. I would first try the troubleshooting steps in this page to ensure the paper path is not obstructed, if that fails I would suggest you Contact HP.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

Windows Folder icon instead of Officejet 6500a Plus E710n icon in Devices and Printers

Can anyone help me to get the OfficeJet 6500a Plus e710n printer icon to display properly in Devices and Printers?
I recently reinstalled Windows 8.1. However, when I installed my printer, instead of the printer icon appearing in Devices and Printers I get a generic yellow Windows folder icon. The Fax icon is OK, just the printer icon is wrong.
If I double click on the icon, I get a mostly blank page with a message near the top saying: "Updated information is available about your device. Click here to download or learn more." If I click on the notice, a dropdown menu appears with "Download updated information" or "Learn more". If I choose downloaded update information, a new printer window appears which is mostly blank except for a message at the centre of the window which says, "No tasks are available on this page" The Learn more option just gives me info about updating drivers.
The printer icon on the Start menu is fine.
I've used HP Print and Scan Doctor to uninstall and reinstall my printer but this hasn't helped. The program found a problem with the printer driver and fixed it, but that hasn't changed the icon either.
I am running Windows 8.1 Pro 64bit fully up to date, and used the latest full version of the HP installation program for the printer (not the basic version) and HP Print and Scan Doctor v4.6.
This question was solved.
View Solution.

Hi,
Try following these steps and let me know if that may help:
From the control Panel select Network and internet and open the Network and Sharing Center.
Click on Change Advanced Sharing Center.
Ensure that Network Discovery is trned on but uncheck the box next to "Turn on automatic setup of network connected devices".
From devices and printer right click the printer and select Remove Device, repeat the for the Fax icon.
Note: if no such option exists for the printer follow the next steps.
Right click the background area and select Device Mahager.
Remove any instance of the printer from Imaging Devices, Printers, Print Queues, Multifunction Adaptors, Other Devices (if a such exists).
Once you are done the printer should no longer appear under Devices and Printers...
Open teh HP Officejet 6500 E710 software, select Connect a new Printer and check for any differnce.
Hope that helps,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

I have two Officejet 6500a's. How do I get them both to work with my laptop?

I now own two Officejet 6500a plus All-in-One printers. I take my laptop back and forth between where they're located. I have the driver on my laptop, and it works with one of them, but how do I make it recognize the second one...and also not then fail to recognize the first one? I'm trying to have both work wirelessly with my laptop. So far, the second one is connected to the wireless network, but my laptop tells me it's not connected to the printer and can't print. I'm not sure what to do because the driver is already installed.
My laptop is a MacBook Pro running OS X Mountain Lion, if that's important.
Thanks in advance for your help!

Sorry that you are having a problem with connecting both printers to the network.
First, you will make sure both printers are on the network through the front panel display screen.
If you have one already working, name it (Officejet 6500 #1, home, work, etc). The 2nd officejet that is not connecting correctly, you will need to re-download the software on the laptop again.
DO NOT uninstall, just install the drivers and software from the website or the CD, if you still have it.
When it ask, how you would like to connect, and you choose wireless, it will search for the printers on the network. Make sure you choose the printer #2 (IP Address).
You can check for the IP address on the settings on the printer.
After it downloads and finishes, you can go to the Devices and printers, and change the name to (#2, work, home, etc).
Even though, its the same software and same printer name, the computer has to distinquish between which is which.
**Click the KUDOS star on the left to say 'Thanks'**
Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.

HP Officejet 6500A Plus will not maintain wireless connection reliably

For the HP EXPERTS on Expert Day, April 18, 2012:
B.L.A.T. (Bottom Line At Top): We have an HP Officejet 6500A Plus purchased about 5 months ago. We wanted to use it as a wireless-connected printer in another room besides our home office. It is useless to us because it will not maintain its wireless connection, even sitting just a few feet from the router in the same room. Except for numerous hours of troubleshooting, we have left it sitting powered up, but unused and idle, for almost the entire 5 months in our home office. DURING ALL THAT IDLE TIME, IT HAS LOGGED OVER 3,200 DISCONNECTS, at a consistent rate of 24 disconnects every 24 hours, even though it ALWAYS reports that the wireless signal quality is “EXCELLENT” (all this is according to the Wireless Network Test Reports we’ve printed throughout the last 5 months). So our question is, what is it that this printer is trying to do once an hour over a wireless connection that is causing these thousands of disconnects? And how can we stop it?
NOTE! Before you round up the usual suspects (namely our router and our PC firewalls) please note that we also bought an HP Officejet Pro 8600 Plus ON THE SAME DAY as the Officejet 6500A Plus. The 8600 was also installed with a wireless connection, and has worked without a single network issue for the entire 5 months.
NOW, FOR THE REST OF THE STORY…
WHO WE ARE: My wife and I have worked on HP equipment for 33 years, starting in 1979 as corporate customers of HP when we worked for Exxon; then we both worked for HP directly for 17 years; and we’ve now used dozens of pieces of HP equipment in our home during the last 12 years in retirement. We’re primarily software folks, so we’re not exactly experts in hardware and networking, but on the other hand, this ain’t our first rodeo either.
OUR CONFIGURATION:
PC’s – All running Windows 7 x64 with all important patches applied and Norton Internet Security 2012: HPE-270f and HP AIO 200-Quad, each with full 6500A and 8600A drivers installed on wireless connection. These 2 PC’s themselves can connect either wirelessly or via Ethernet to our home network. The 270f has a dual-band wireless board. Both bands work. We also have a new dv7t laptop with only the full 6500A driver installed via wireless connection. The laptop is now upstairs and it’s connected to our home network wirelessly without any issues. (This is where we had hoped to also put the 6500A, but it needs to work reliably via wireless connection.)
ROUTER: Netgear N600 WNDR3700 providing Ethernet and wireless networking. Router provides a very strong wireless signal throughout the house. No wireless problems with any other equipment including an iPod, two Kindle Fires besides all the HP equipment.
PRINTERS: Besides the two HP printers, the HPE-270f PC has a Canon MP960 installed on it. And if we can’t get the 6500A working right or replaced with something that does work right, we may be buying our second Canon printer. By the way, on the 6500A, ePrint and App’s are set to ON, but of course they’re not being used, just like everything else on this AIO.
OTHER: We also have a Sonos music system that connects to our network via Ethernet and has its own proprietary mesh network (on another frequency) for transmitting ripped music wirelessly to speaker units throughout our house. (If you aren’t familiar with this totally cool system, check out sonos.com). We’ve never seen any evidence of interference between these two wireless networks, or our wireless phone sets either.
HP TOOLS AVAILABLE ON ALL 3 PC’s: HPU
UPDATE 5.003.001.001 (reporting everything up-to-date); HPHDU 3.1.0.17; HPPDU 5.0.0.015 and HPNDU 4.3.0.002.
SYMPTOMS: The 6500A Plus installs quickly and easliy, and connects wirelessly just fine during installation. But sometime over the next hour (usually less), it disconnects and won’t print from PC applications. Sometimes the application puts up an “Unable to communicate with printer” screen, even though the PC usually thinks the printer is “ready”. Other times, the PC thinks the printer is offline (but printers don’t have “offline” buttons anymore!). Often, if you just leave everything alone, the 6500A will somehow reconnect and print out the spooled file 5-30 MINUTES later. So it does usually seem to be able to recover given some time, but that doesn’t always fit our schedule! Occasionally, turning the wireless radio on the printer off and back on will fix it right away. But usually, you have to power the printer completely off, and then back on. As far as we know, that always fixes it…..until the next disconnect a few minutes later!
PREVIOUSLY TRIED: After reading some of HP’s wireless network support websites, I manually assigned a fixed IP address to this printer. It didn’t seem to matter; according to the wireless network test report, it still logs disconnects at the rate of one per hour, and all the failure symptoms were the same.
We also dabbled a bit with setting this printer as “trusted” to the Firewall, but that didn’t seem to matter either.
Next, we connected the printer via Ethernet. The printer immediately started to work, even though it had just been in its “failed” state over the wireless connection. As far as we know, it never failed while connected via Ethernet. This seems to point to a purely wireless hardware/firmware problem on the printer itself.
Late last year, I tried two different chat sessions about this with the inter-continental AIO support teams, each one lasting several hours. Unfortunately, none of their optimistic solution scripts seemed to fit our problem. They both seemed determined to reconfigure the 6500A as a TCP/IP printer, which of course worked fine initially, just like everything else. At this point, they would understandably want to close the chat. But 20-30 minutes later, we could no longer print to it. During the second chat, they got into one of our PC’s remotely and effectively turned off the spooler (by selecting “Print Directly” or something like that). After that, all was well again (as usual) UNTIL the printer disconnected, at which time attempting to print from that PC would HANG the application (since the spooler was no longer buffering) and eventually hang the whole PC. One giant leap backwards. That’s when I gave up on the multi-hour chat sessions.
The three diagnostic utilities (HDU, PDU, NDU) have been tried over and over. When the printer is in its disconnected state, the DU’s usually don’t detect the 6500A at all, or if they do detect it, they are unable to fix anything. Frankly, it’s easier to just power the printer off (which takes about a minute) and power the printer back on (which takes more than a minute) and then wait for the spooler to kick in (usually about 30 seconds). BUT WE DON’T CONSIDER THAT A SOLUTION!!
B.L.A.B. (Bottom Line At Bottom): We have used up nearly the entire black ink cartridge and at least a ream of paper troubleshooting this brand new printer, to no avail. This printer is useless to us unless it can maintain a wireless connection reliably. Please help!
Thanks –
Bob and Jane
(Note: we have an appointment from about 11:20 am EDT – 1 pm EDT, 8:20 am PDT till about 10 am PDT)

I bought the Officejet 6500A Plus about one month and have experienced the very same problem. I tried to remedy this problem following suggestions in a number of different posts (static IP, router, firewalls etc), all to no avail. Last week I called support. The support I received by the tech over several hours and different days for a week was very good. However none of his suggestions corrected the connection issue. After today's recommended fix failed, he advised HP is aware of this issue with the 6500 and other affected printers. He claimed HP was working on a firmware upgrade. He did not know when the update would be provided. The tech also claimed HP acknowledged this problem in a written announcement. He agreed to email the announcement to me. I haven't received it. This has been the only problem I've had with the 6500

Problems printing to HP officejet 6500A plus e-All-in-one printer e710n

Hi,
I am struggling to print to my " HP officejet 6500A plus e-All-in-one printer e710n". According to the setup network test (Wireless network test report), everything is successful (status "PASS" for all fields). I also checked that the IP configured is the same as the IP displayed on the printer when i push the wireless button (updated via "Update IP address").
I have a laptops as well as netbooks connected to the wireless network. All these devices could previously print, however now none of them can. When i run the diagnostics (both the standard trouble shooter, as well as the one from microsoft when clicking on the fixit option), no problems are detected. When checking the device manager, i can see no conflicts.
When i open the printer control panel and click on "Customize your printer" and then go to "Ports" and click on the "configure port" option, i get an error "An error occurred during port configuration. Operation could not be completed (error 0x0000007b).".
Please assist with any suggestions.

I was able to resolve the problem.
I reinstalled the printer on one of my other laptops (this might have cleared up an error on the printer). I think the true problem is related to the fact that we left the printer on, we've started switching it off when not in use. Even though it goes into sleep mode, it seems to cause problems over time if not switched off on the printer itself.
The basics i did was check the network connection, printed a status of the network connectivity (you can do that from your control panel on the printer). If the network looks good, then try leaving your printer off for an hour or so, if that doesn't work, try reinstalling the printer on your device and start switching it off after use. I know it sounds crazy, but that's what i've been doing and haven't had a problem since.
It was a strange problem, in some cases i wasn't able to see the printer from devices that previously could, when the devices that could see the printer tried to print, it would print okay for a few pages and then start printing garbage, followed by failing completely and cancelling the print. When this happened there would be an error on the device saying it cannot connect to the printer, even though it could at the start of print.

Envelopes on Officejet 6500A from Word 2007 on Win 7

Just upgraded from a Photosmart 1200 printer.
Previously Word 2007 would happily print DL envelopes on the Photosmart.
Now the Officejet 6500A keeps stating that the paper size is wrong. Tried both the custom paper size (110 x 220mm for DL) and the Microsoft Word Envelope facility, both give paper size errors
Martin Lines

Yep, I had the same problem with DL & C5, support ,no support. Try the following, it worked for me.
Set up as normal in Word for the envelope you want. Making sure all is as you would simply go to print i.e insert addresses etc. then:
Click on Office Logo, select Print from drop down then click on Print in window.
select Preferences then click on ( and this is the clever bit) Draft. click on OK and the envelope should print.
Beware, if you select the draft option before the word setup you will print any associated word letter on the envelope.

How can i make my officejet 6500a print in black and white only?

I just bought an officejet 6500a and I can't figure out how to make it print in black in white only. I print a lot of stuff that doesn't need color and want to save my ink. On some prints it gives me that option when I print. but for the most part it doesn't allow me to change to black and white on things i am printing off the web

Pages 30-34 of the user manual for the Officejet 6500A covers how to change print preferences for the printer with both Mac and Windows. It covers documents, brochures and photos and covers finding the gray scale option. Here is a link to that manual http://goo.gl/6J61R .
I hope that this helps.
I am a former employee of HP...
How do I give Kudos?| How do I mark a post as Solved?

HP Officejet 6500A Plus

My HP Officejet 6500A Plus all in one printer recently stopped functioning and printing. First the Wireless network stopped working (Wireless Status Disconnected) and the Wireless Netwok Test Report advice was “contact HP support”. Then I started getting endless errors and flashing print screens with numerical references like 83C00009, 00729C98 etc. Any attempt to turn off the printer using the “off button” resulted in another error message. The following are examples of the stream of new error messages that appeared each time the “off button” was pressed: B0000A16; B03DA14A; B811DEB6; B8383184; B03E3B66; B83D99B8 etc. To finally “turn off” the printer it became necessary to disconnect the power. I have consulted the manual and queries on the HP site using the numerical references as search criteria, does not return any useful results / strategies. I found a video about how to do a partial “reset” (turn on using # + 3) but while this did allow me to access the print screen, it did not resolve anything and the numerical errors and flashing lights reappeared. I downloaded the HP diagnostic tools, but they came up with nothing – i.e. could not communicate with my printer. I read on some post that there may be a problem with the printer head, so I ran the Printer Status Report, but it seemed OK. Regardless I ran the clean the PrinterHead tool, and again this seemed OK, so I didn’t run the 2nd stage. My printer is out of warranty. It is 1.5 years old, but hasn’t been used that much. According to the Printer Status Report it has printed 1534 pages and scanned 290.
What can I do? Most of the "internet searches" suggest that if the printer is out of warranty the only option is landfill.

Thank you. Thesole reason I bought this printer was to use its wireless “Airprint” functionality to print from an iPad and when it worked it was a fabulous product. The start of these constant alphanumeric errors seemed to coincide with the wireless function ceasing to work (it went offline, HP Network Configuration Report – Network Status “Offline”, and Wireless status “Disconnected”). Maybe that was just a coincidence. Running the “Wireless Network Test Report” the recommendation is “Contact HP support***”. I.e. The Wireless is on (blue light good) PASS, but the Wireless Working status is FAIL.
I have only tried using the USB in an attempt to get around the wireless not working, i.e. still able to do some basic printing and perhaps upload firmware updates etc. I have tried different USB ports on my laptop computer but only with the same USB cable that came with the printer. This original printer cable has only been used a couple of times and it has on two occasions allowed me to print successfully from the laptop (i.e. initially it worked although . Surely it should be OK. I am reluctant to go out and buy another cable in the hope that it might resolve something and I don’t really have access to another computer to test.
Thank you I have previously seen that article. It was somewhat useful. My errors messages (mostly 83C0009, and sometimes just a black and white striped screen or B0525DAE, B866A570 etc) however do not include system ink failure and the article basically therefore simply recommends switching the computer off at the same time the ink cartridges are removed. This has in the past provided some improvement in the frequency of the error messages but it is usually short-lived and the error message returns. The error message can however become entrenched and at that point the print cartridges don’t move when the printer door is open and therefore can’t be removed. At this point I've tried turning the printer on while holding down #+3 to try and get back to a home screen, rather than an error screen.
On the upside, I can occasionally still make photocopies and the print quality is good.
Any guidance on what I should do next?

SOLVED! HP Officejet 6500A E710 will not stay connected to the network. scanner not connected

After 5 hours of live remote HP tech support, and 10 more hours of web searching, I am happy to say I have solved the wireless network connection issue with scanning and printing using the HP Officejet 6500A E710n-z. I notice that there are a lot of people with similar issues with no common, successful fix. Here is what worked for me.
Background Info:
Upgraded internet service from 9Mbps to 27Mbps...Provider brought out new Arris DG860 modem/router. Configured network and connected all clients (smart phones, PCs, Tablets, etc) successfully accept the printer. With this new router/modem the printer/scanner/fax would not connect to my PC at all (Windows 7 64-bit). The Officejet was always connected to the network, however, anytime I tried to print I would get an error "Unable to connect to the printer...", and when I made an attempt to scan.."Scanner not connected, make sure it is connected to the network..." blah blah blah.
Process:
After searching the web for solutions with no success, I finally made my first call to HP tech support. Tech tried numerous fixes: many network changes (channel, static IP, etc.), made changes to Windows system settings and registry, installed new software and drivers, ran the scan doctor, partial, semi, and full reset on the printer. He changed my wifi channel to 6 (or 11) from AUTO and whola. That seemed to fix the problem. After hanging up the phone 10 minutes later "No connection" errors again. Made a second call to HP Tech Support, and this new tech basically tried all the same fixes as the first tech. Worked again for 10-15 minutes then disconnected. Made third call to tech and this individual tried the same fixes as the previous two, but to no avail. He said he would have to direct me to a more Advanced Technician and would call back tomorrow. They called back the next day, and this new tech fixed the issue within 20 minutes.
Problem/Solution:
The fourth "more advanced" tech made one change in my network configuration settings. He changed my network mode from B/G/N to B/G and now the printer/scanner/fax stays connected and works like brand new. The only problem is that all my devices (including the Officejet) are 802.11N capable. Setting my network to the old B/G mixed mode slows my speed down just a bit. Using B/G/N mode or N, my download speed is 27 Mbps. On B/G mixed my speed is 25Mbps. Not too big of a deal, though. All the HP Support Techs were very nice and helpfull. They refunded my $25 Tech fee [fee charged when product is out of warranty] because the problem is not "technically" solved, even though it does work. Conclusio: This seems to be an issue with my the modem/router provided by my ISP. Could also be that it is an older Officejet and need to upgrade. To Fix Follow the Steps Below:
Step 1: Find your default gateway IP...usuall 192.168.0.1 or 192.168.1.1 or similar. Type this IP into your web address bar and hit enter.
Step 2: Enter the username and password. This is normally set at factory default --> username: admin ....passowrd: password .... or .... admin
Step 3: Go to the "Wireless Setup" tab and under the "Advanced Options" and "Wireless Network Settings" change the "Wireless Mode" to "B/G mixed".
Step 4: Click "Apply" then close the browser.
You may, or may not, lose your wifi connection for a short period while the new settings are applied and you may, or may not, have to power cycle your modem/router. That's it. Worked for me and I hope it works for you too. If you have any questions or comments please feel free to post.

OK, that all sounds right. Here are a few more router config ideas:
1. Make sure that 802.11g mode is available, along with others is OK, but 'g' must be present.
2. Change the channel to 11.
3. Use WPA or WPA/WPA2 encryption, not WPA2 only.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Wireless configuration for HP OfficeJet 6500A plus All-In-One printer on Ubuntu 10.04

I have bought a HP OfficeJet 6500A plus All-In-One printer CN557A, which I want to use with ubuntu 10.04 64-bit as a wireless network printer.
Before i bought i checked compatibility on www.hplipopensource.org and www.openprinting.org, and all was in order.
The machine is autodetected and fully functional when connected with a usb cable, but i have not managed to get it to work as a wireless printer.
This is what I did:
I configured the printer on the wireless network (through the printer interface), and it connects. It prints out a "Wireless Network Test Report", and everything works. I can ping to its local ip adress, and access it through the browser. HP eprint also works.
I installed hplip 3.11.10 and dependencies manually. I did this because the default hplip in ubuntu 10.04 did not recognise the device.
I ran 'hp-check', which gave no errors or warnings:
tjoff@mek-403-jakbo-01:~$ hp-check
HP Linux Imaging and Printing System (ver. 3.11.10)
Dependency/Version Check Utility ver. 14.3
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Note: hp-check can be run in three modes:
1. Compile-time check mode (-c or --compile): Use this mode before compiling the
HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies
are installed to successfully compile HPLIP.
2. Run-time check mode (-r or --run): Use this mode to determine if a distro
supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball
has the proper dependencies installed to successfully run.
3. Both compile- and run-time check mode (-b or --both) (Default): This mode
will check both of the above cases (both compile- and run-time dependencies).
Saving output in log file: hp-check.log
Initializing. Please wait...
| SYSTEM INFO |
Basic system information:
Linux mek-403-jakbo-01 2.6.32-35-generic #78-Ubuntu SMP Tue Oct 11 16:11:24 UTC 2011 x86_64 GNU/Linux
Distribution:
ubuntu 10.04
Checking Python version...
OK, version 2.6.5 installed
Checking PyQt 4.x version...
OK, version 4.7.2 installed.
Checking for CUPS...
Status: scheduler is running
Version: 1.4.3
error_log is set to level: warn
Checking for dbus/python-dbus...
dbus daemon is running.
python-dbus version: 0.83.0
| COMPILE AND RUNTIME DEPENDENCIES |
note: To check for compile-time only dependencies, re-run hp-check with the -c parameter (ie, hp-check -c).
note: To check for run-time only dependencies, re-run hp-check with the -r parameter (ie, hp-check -r).
Checking for dependency: CUPS - Common Unix Printing System...
OK, found.
Checking for dependency: CUPS devel- Common Unix Printing System development files...
OK, found.
Checking for dependency: CUPS image - CUPS image development files...
OK, found.
Checking for dependency: DBus - Message bus system...
OK, found.
Checking for dependency: gcc - GNU Project C and C++ Compiler...
OK, found.
Checking for dependency: GhostScript - PostScript and PDF language interpreter and previewer...
OK, found.
Checking for dependency: libcrypto - OpenSSL cryptographic library...
OK, found.
Checking for dependency: libjpeg - JPEG library...
OK, found.
Checking for dependency: libnetsnmp-devel - SNMP networking library development files...
OK, found.
Checking for dependency: libpthread - POSIX threads library...
OK, found.
Checking for dependency: libtool - Library building support services...
OK, found.
Checking for dependency: libusb - USB library...
OK, found.
Checking for dependency: make - GNU make utility to maintain groups of programs...
OK, found.
Checking for dependency: PIL - Python Imaging Library (required for commandline scanning with hp-scan)...
OK, found.
Checking for dependency: PolicyKit - Administrative policy framework...
OK, found.
Checking for dependency: PyQt 4 DBus - DBus Support for PyQt4...
OK, found.
Checking for dependency: Python DBus - Python bindings for DBus...
OK, found.
Checking for dependency: Python devel - Python development files...
OK, found.
Checking for dependency: Python libnotify - Python bindings for the libnotify Desktop notifications...
OK, found.
Checking for dependency: Python XML libraries...
OK, found.
Checking for dependency: Python 2.3 or greater - Required for fax functionality...
OK, found.
Checking for dependency: Python 2.2 or greater - Python programming language...
OK, found.
Checking for dependency: Reportlab - PDF library for Python...
OK, found.
Checking for dependency: SANE - Scanning library...
OK, found.
Checking for dependency: SANE - Scanning library development files...
OK, found.
Checking for dependency: scanimage - Shell scanning program...
OK, found.
Checking for dependency: xsane - Graphical scanner frontend for SANE...
OK, found.
| HPLIP INSTALLATION |
Currently installed HPLIP version...
HPLIP 3.11.10 currently installed in '/usr/share/hplip'.
Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf. Generated from hplip.conf.in by configure.
[hplip]
version=3.11.10
[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/HP
ppdbase=/usr/share/ppd
doc=/usr/share/doc/hplip-3.11.10
icon=/usr/share/applications
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv/hp
# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
pp-build=no
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=no
foomatic-drv-install=no
foomatic-ppd-install=no
foomatic-rip-hplip-install=no
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.11.10
restricted-build=no
ui-toolkit=qt4
qt3=no
qt4=yes
policy-kit=no
hpijs-only-build=no
lite-build=no
udev-acl-rules=yes
hpcups-only-build=no
hpijs-only-build=no
Current contents of '/var/lib/hp/hplip.state' file:
# hplip.state - HPLIP runtime persistent variables.
[plugin]
installed=0
eula=0
Current contents of '~/.hplip/hplip.conf' file:
[last_used]
printer_name =
working_dir = .
device_uri = "hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW"
[commands]
scan = /usr/bin/xsane -V %SANE_URI%
[installation]
version = 3.11.10
date_time = 2011-11-16 14:30:35
[settings]
systray_messages = 0
systray_visible = 0
[fax]
email_address =
voice_phone =
[refresh]
rate = 30
enable = false
type = 1
[polling]
enable = false
device_list =
interval = 5
| DISCOVERED USB DEVICES |
Device URI Model
hp:/usb/Officejet_6500_E710n-z?s HP Officejet 6500 E710n-z
erial=CN16F2402Q05JW
| INSTALLED CUPS PRINTER QUEUES |
B-403-271-A4-COLOR2
Type: Unknown
Device URI: smb://mek-ps1.win.dtu.dk/403-271-A4-Color
B403-271-A4-BW
Type: Unknown
Device URI: smb://mek-ps1.win.dtu.dk/403-271-A4-BW
HP-Officejet-6500-E710n-z-FAX
Type: Printer
Device URI: hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW
PPD: /etc/cups/ppd/HP-Officejet-6500-E710n-z-FAX.ppd
PPD Description: HP Officejet 6500 e710n-z, hpcups 3.11.10
Printer status: printer HP-Officejet-6500-E710n-z-FAX is idle. enabled since 2011-11-16T01:00:45 CET
Communication status: Good
| SANE CONFIGURATION |
'hpaio' in '/etc/sane.d/dll.conf'...
OK, found. SANE backend 'hpaio' is properly set up.
Checking output of 'scanimage -L'...
device `hpaio:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW' is a Hewlett-Packard Officejet_6500_E710n-z all-in-one
| PYTHON EXTENSIONS |
Checking 'cupsext' CUPS extension...
OK, found.
Checking 'pcardext' Photocard extension...
OK, found.
Checking 'hpmudext' I/O extension...
OK, found.
Checking 'scanext' SANE scanning extension...
OK, found.
| USB I/O SETUP |
Checking for permissions of USB attached printers...
HP Device 0x5412 at 002:005:
Device URI: hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW
Device node: /dev/bus/usb/002/005
Mode: 0664
| USER GROUPS |
lp adm dialout cdrom plugdev lpadmin admin sambashare vboxusers
| SUMMARY |
No errors or warnings.
Done.
I then ran 'sudo hp-setup', chose the device (which was detected), chose my wireless network, entered the wireless security key. On the configuration results dialog I get two messages:
"Your printer has been succesfully configured on the wireless network. You may now unplug the USB cable"
and
"The Ethernet cable is plugged in which will prevent you from connecting to a wireless network. To connect wirelessly, remove the cable and try again. (VSA000)"
There is no ethernet cable plugged in, so i can't remove it. I unplug the USB cable and click 'finish'. This makes the 'hp-setup'-dialog start over again, and the printer has not been installed.
In the terminal i have the following:
tjoff@mek-403-jakbo-01:~$ sudo hp-setup
[sudo] password for tjoff:
HP Linux Imaging and Printing System (ver. 3.11.10)
Printer/Fax Setup Utility ver. 9.0
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Searching on USB bus...
GET /IoMgmt/Adapters HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/WifiNetworks HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/Profiles/Active HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/Protocols HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
error: Missing response key: 'iorotocols-iorotocol-dd:dnsserveripaddress-0'
GET /IoMgmt/Adapters/Wifi0/VsaCodes.xml HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/WifiNetworks/SSID=mVnmXfsu HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/IoConfig.xml HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
I then tried to reconnect the printer usb cable and run 'hp-toolbox' and click "Wireless/wifi setup using USB". Now i get the error:
tjoff@mek-403-jakbo-01:~$ hp-toolbox
HP Linux Imaging and Printing System (ver. 3.11.10)
HP Device Manager ver. 15.0
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
HP Linux Imaging and Printing System (ver. 3.11.10)
Wifi Configuration Utility ver. 1.1
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
error: Channel write error
error: An I/O error occurred. Please check the USB connection to your printer and try again. (Device I/O error)
Done.
I do not how get past this stage, and any help is welcome.
This question was solved.
View Solution.

A friendly soul on ubuntuforums pointed out to me, that the wireless configuration is only necessary when the printer is NOT connected to a (W)LAN. So all I really had to do was to configure the printer in the CUPS administation page, and it worked. Problem solved. Silly me.

Apple Airprint to HP Officejet 6500A Plus via Wired Connection to Router

Hi There,
So I've done a considerable amount of research into this across the internet and this forum and I'm still struggling to find a satisfactory solution.
I have an HP Officejet 6500A Plus connected by ethernet into my BT Homehub 3.
It is my understanding that even though this is a wired connection, as long as my iOS device (iPad 2 or iPhone 5) is connected to the same router, I should still be able to see this Officejet over through the airprint facility.
Unfortunately this is not the case. I only get the "No Airprint Printers Found" message on both devices. The only way I have managed to get my Mac Pro (Mavericks) to connect was to mannualy add using the IP address for the printer.
Can anyone give any guidance as to what I might be doing wrong? The printer is definitely connecting to the internet as I can print from my iOS devices using HP ePrint app for iOS.
Some might say well what is the problem, just use the HP app but this is not point. I believe if something has been implemented to make things easier then use it. I chose this printer specifically for this functionality so it's a little frustrating to find it so difficult to achieve the desired results.
Hope it's something straightforward and someone can help.
Thanks,
Steve
This question was solved.
View Solution.

Further to this request, and reading many more similar issues, I think I may resolved this.
I am not 100% sure but I have read some threads suggesting there are issues around BT's Homehub 3 and bonjour so this may be an issue.
I have tried the following over the past couple of days...
1) Completely reset my router (wiped all settings and started again) - No luck!
2) Tried changing from WPA2 to just WPA security - No luck!
3) Tried forwarding the bonjour ports to the printer - No luck!
4) Switched off router, printer and all iOS devices then powered back router, printer and then iOS devices - Printer appears on iOS devices but when print was selected, iOS device repeatedly returned Printer Not Connected error.
Finally, what seems to have done it (at least for now) was...
1) Unplugged ethernet from the Officejet and set it up as Wireless connection.
2) Powered down router, printer and all iOS devices then powered back up in the order stated earlier.
3) So far I have tried printing an email and a web page from my iOS devices and both have been sucessful.
Incidentally I had been struggling also to airplay from my iPhone and iPad until I started messing around with settings above and now this issue also seems to be resolved.
Due to variety of combinations (different printers, routers etc) people will have, it seems to be quite difficult to find a solution which addresses an individual problem however I hope some of my experimenting and findings might help others in some way.

HP Officejet 6500A Plus e-All-in-One Printer - E710n wireless print and web app problem

We have an HP Officejet 6500A Plus e-all-in-one Printer - E710n and run Windows 7 on our laptop.
I have run the wirelss setup wizard and have successfully connected the printer to the router, and both the laptop and printer are on the same network and have identical SSID.
However, we can not send any prints the printer wirelessly. We have to hook it up to the USB to do so. We are also unable to access our web apps; pressing the app button on the printer control panel brings up the following:
"Connection error. The printer was unable to connect to the server. Check your internet connection and try again."
I have run through the suggested solutions under "A Network Connected Printer Cannot Access Print Apps, Web Services, or ePrint" in the customer care help centre which didn't work, although when I tried to enter the IP address under IPv4 into the browser address bar it timed out. I tried the HP Print and Scan Doctor, but it returns a result that suggests everything is fine.
I turned off the firewall and tried again with no luck.
I really am at a loss now. Diagnostics say it should work, but it doesn't. Help!

Disable Bitdefender altogeher and try again.
Also, see this: http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02251103
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Officejet 6500a won't install wirelessly on Win 7 HP laptop.

Officejet 6500a won’t install wirelessly on Win 7 HP laptop. Does fine wirelessly on generic desktop pc. HP Support Assistant does not detect this unit. At one time, I had the laptop wired to the printer, so all the relevant data were transferred automatically.

Loves_to_Dance wrote:
Officejet 6500a won’t install wirelessly on Win 7 HP laptop. At one time, I had the laptop wired to the printer, so all the relevant data were transferred automatically. Here's the problem you first need to remove the previous setup otherwise it will interfer with the different setup. Wireless and wired use different setups. Since you didn't remove the previous install it expects it to be wired connection.

My HP OfficeJet 6500A Plus printer/scanner/fax/copier won't connect to my wireless network

I tried going through the Wireless Network setup on my HP OfficeJet 6500A Plus machine. The printer recognizes the network and I then type in my network's password but it won't connect to the network. What can I do? I would like to be able to print and scan wirelessly. Help please!

Hello erking,
Sorry to hear that you are having an issue with connecting the printer to your Mac over a wireless connection.
I have done some research and I have found a great document that deals with The Printer Is Not Found During a Wireless Network Installation.
Please feel free to write me back and I will be happy to assist you further with any questions or concerns you may have.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

HP Officejet 6500A Plus not staying connected to wireless network

Just picked up a HP Officejet 6500A Plus e-All-in-One Printer - E710n the other week and set it all up and it was working wonderfully. But I noticed after it goes into sleep mode it disconnects from the wireless network and doesn't reconnect.
I will get a overview of how I have it all set up.
I have a DSL modem with a TRENDnet TEW-639GR router connected to it. I have set my router to reserve IP addresses for the computer and printer. That way I can leave the computer and printer wireless IP settings as automatic and they will always get the same IP address. I do this for the wireless network at my parents place as well and it works perfectly with their HP Photosmart C7280.
I also set up the HP ePrintCenter feature on the printer so that I can print by sending the printer an email. When I first set it all up this was working great. I tested it all and it was awesome. When I would log onto the ePrint website it would show as connected and it was all good.
So then what happened was it was all fine then the next day when we want to print something the computer says the printer is offline. I go on the HP ePrintCenter website and it says not connected. I print out a wireless network report page and it says not connected. After I printed that test page, I guess it woke up the printer enough or something as it then connected to the router and printed fine as well as showed up as connected on the ePrintCenter website. So all was good. Then the next day the printer goes to sleep and again it shows as disconnected.
Should it not be staying connected in sleep mode? How will the printer know something is being sent to it and that it should wake up if it is not staying connected?
Any suggestions of what I should change with the settings? I suppose I could try setting the IP settings as static on the printer itself but I shouldn't need to as I set it to static on the router. When it finally does reconnect it does always keep the same IP. If that is what is required I guess I could do that but then what is the point in having an automatic setting if it doesn't work? I would rather have this issue fixed that have to do a work around for it.
Thanks in advance!

Hi,
The printer should stay connected to your wireless network after the printer enters the sleep mode.
This is not an expected behavior.
I believe such an issue may be caused due to a signal quality or any conflict as too many broadcust on the same channel.
Please try the following steps in order to better understand the issue:
Follow the Wireless Setup Wizard if your printer currently disconnected
Enter the Setup menu.
Enter the Network menu.
Click Wireless.
Click Wireless Test Report.
What is the signal quality provided by the report and what channel used to broadcast by your router?
If you may scan and attach the report, it may help to better understand any possible cause.
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

This Officejet 6500A is so noisy - both previous HP printers were quite. Sounds like a tractor

Similar Messages

Maybe you are looking for