Thunderbolt data service down

Spoke with tech support who confirmed that data service is down for some (but not all Thunderbolts). My wife's tbolt has been out since midnight. Rep stated no ETA, but there are issues network wide.
Anyone else experiencing a problem with their tbolt? My droid incredible is working fine.

budone wrote:
silver6055 wrote:
budone wrote:
I can see her statement making sens for 4G(LTE) service. But not 3G as it uses the same 3G towers and antennas as the rest of us, when not hitting an LTE tower. Makes me think a phone setting is incorrect. Maybe set to 4G service only. Go into SETTINGS>NETWORKS & WIRELESS and make sure Mobile Network is checkmarked.
Personally I would call tech support from another phone. Or do a master reset, if you have not added too much to the device.
BUt doesn't the thunderbolt require the SIM card even for 3G? So, if something was wrong with the SIM authentication system, this would make sense, service out for Thunderbolts but not for other phones.
I dont think so. But I could very well be wrong. I believe the SIM is strictly for 4G. Even if that was the reason, wouldn't ALL TB's be DOA?
No, 3G needs the SIM as well, check out, for example, this thread: http://community.vzw.com/t5/ThunderBolt-by-HTC/Htc-Thunderbolt-Sim-Card/td-p/447368
Since I am making up the explanation... it could be that "part" of a SIM authentication is down (e.g. some fraction of a distributed database) while the rest works. But, this is based on absolutely no knowledge of the real situation, just giving a possible explanation of how thunderbolts could be impacted while 3G phones are ok.

Similar Messages

Is data service down in IL

I don't have any data service in IL...is service down?

Oh boy, well I would imagine not, but let's find out what is going on! What zipcode are you in? What model phone are you using? Do other customers experience an issue with data as well?
SandyS_VZW
Follow us on Twitter @VZWSupport

Is LTE data service down in Madison Area?

Verizon HTC Thunderbolt - has been having spotty 3G coverage over the past week. Woke up today with no data connection at all. Was able to connect to my home's wifi to update a few apps. My entire 15 mile drive into work showed not so much as 1x connectivity ...nothing!
Now just over an hour later, after two restarts, and a battery reset, I still have NO 3G and no 1x data connectivity. I have even gone as far as using the LET OnOff application to switch from CDMA + LET/EvDo auto, to CDMA auto (PRL) with no change in connection status. I have currently reverted this back to CDMA + LET/EvDo audio.
I know that Madison and the surrounding are is one of many upcoming regions slated to receive 4G activation in mid June - could this have anything to do with the data interruption?
I work in the IT industry, and changes outside of maintenance windows are extremely frowned upon due to impact to customers. I am beginning to get perturbed. I use my phone for work, and am crippled without it.

Oh boy, well I would imagine not, but let's find out what is going on! What zipcode are you in? What model phone are you using? Do other customers experience an issue with data as well?
SandyS_VZW
Follow us on Twitter @VZWSupport

Data service ONLYT to retry NOT to failover when service is down

Hi All,
I have around 10 services to be clustered under 3.2 with network aware agents; normally I use scdbuilder to create agents.
There is few services, which I want them to stay down if they fail in the running node.
Let say I have service1 - running on port 2000, If port 2000 is down, I want advice it to restart this, failing the restart I want to make it START_FAIL, rather than switching to other nodes and try to restart there.
Is it possible to achieve this thru Sun Cluster 3.2
Thanks for the time,
Aruna

Hi Detlef,
Many thanks, I was reading about failover mode property - RESTART_ONLY, I guess It should work becoz my data services are build from scdsbuilder, so they should use DSDL. I will test it.
Thanks again,
Aruna

Unable to create records in database using PHP Data Service

Hello, I've been stuck on this for a few days and search up and down for this on the net, no response I've found has worked, so I come to you...
Here are the steps I've taken, I think it's pretty standard
1. I have a macbook pro running osx 10.7.3
2. I installed MAMP all default (I've acually reinstalled this because someone suggested this might fix it)
3. Thru phpMyAdmin I created a database called my_test
4. In that database I created a table, this is the export of that table: (I've also tried this with InnoDB which is the default)
CREATE TABLE `customer` (
`id` int(10) unsigned NOT NULL AUTO_INCREMENT,
`name` varchar(50) NOT NULL,
`email` varchar(150) NOT NULL,
PRIMARY KEY (`id`),
UNIQUE KEY `id` (`id`)
) ENGINE=MyISAM DEFAULT CHARSET=latin1 AUTO_INCREMENT=1 ;
5. I created a new Flx Project (Running Flash Builder 4.5.1 Premium)
     Project Name: PHPTest
     Application Type: Desktop (Although I've done the same thing with Web and got the same results)
     >> Next
     Application Server Type: PHP
     Web Root: /Applications/MAMP/htdocs/
     URL Root: http://localhost:8888/
     Clicked 'Validate Configuration' and that worked
     Output Folder: /Applications/MAMP/htdocs/PHPService (default by Flash Builder)
     >> Finished
6. On the Data/Services tab on the bottom I click 'Connect to Data/Service...'
     Select 'PHP'
     >> Next
     Select 'Click here to generate a sample'
     Select 'Generate from database' radio button
     Username: root
     Password: root (default for MAMP)
     Host name: localhost
     Server port: 8889 (default for MAMP MySQL port, the HTTP port default is 8888 which in both cases seem to work but every video I've seen that uses MAMP on youtube uses 8889)
     Database: my_test
     Click 'Test Connection' (works)
     Table: customer
     Primary Key: id (this field is greyed out and Flash Builder selects 'id' which it figures out from the SQL table)
     >> Click OK
7. Then if I don't have the Zend Framework folder in my /Applications/MAMP/htdocs/ folder it tells me its going to create that and I say alright. Then Flash Builder says stuff about how this is really only for testing and not production server ready and I say alright.
8. Then it takes me back to the Form from Step 6 when I get the chance to select 'Click here to generate a sample'
     These fields are now filled with this data automaticly:
     PHP Class: /Applications/MAMP/htdocs/PHPTest/services/CustomerService.php
     Service name: CustomerService
     Service package: services.customerservice
     Data type package: valueObjects
     >> Click Next (shows all the functions that will be now availible)
     >> Click Finished (End of the forms and it opens Dreamweaver to the php file it created CustomerService.php which I have no need to edit so I close that down)
9. Back in Flash Builder I switch to design view and drag a datagrid onto the big white area in the middle, whatever that is called.
10. Then below in Data/Services tab on the bottom I click drag the function 'GetAllCustomer' on top of the datagrid.
     I say yes to rebound and click ok and the view of the datagrid is updated with the colums from the 'customer' table in mySQL.
(Now let me say that when I hit save and compile this, if I actually had records in this table that I insert thru phpMyAdmin, this does show in the datagrid. So for the whole CRUD thing I am able to get the R which is Read)
11. Now going back to the design view in Flash Builder I will create a form to create records in the table... (I guess this isn't really a step)
12. In the Data/Service tab on the bottom I select 'createCustomer' function and then there is an icon called 'Generate Form' that looks like a white piece of paper with a gear on the bottom of it.
13. This opens up a new form and since I don't have a crazy bunch of fields in my table I just click Finished (If you click next you can specify which fields you want to exclude from the form but this time I don't need to)
14. This actually creates 2 forms if you look at the code, the second just shows the return type from when you click 'CreateCustomer' button on the first form. Because they overlap in design view I drag the form out of the way so you can see the input form, the return form, and the datagrid
15. Then I save and compile...
(Also if your actually reading this I didn't remove the id form field, I get the same result either way, but if you do remove the form field in the code/design you also have to update the button function to not deal with the id before it gets sent off to the php page since in this case the MySQL table is set to auto_increment the id, sorry this doesn't make much sence but this little area doesn't matter much either way)
16. Now fill in whatever data you want for name and email, try differnt numbers in the id field like 0, nothing, 1, 1000 and click 'CreateCustomer'
(For me nothing happens, no return is put in the return field, no error pops up and the datagrid is not updated with the new record, also going over to phpMyAdmin and checking out the table browse doesn't show any changes either, I know the button is calling the function because if I add a state change in that function it changes, it would seem that the line:
createCustomerResult.token = customerService.createCustomer(customer2); doesn't do anything)
So any idea what is wrong here, I'm convenced it's something stupid easy simple I just can't see it.

In case you need more info, here is a code dump on a mxml project that has this problem:
<?xml version="1.0" encoding="utf-8"?>
<s:WindowedApplication xmlns:fx="http://ns.adobe.com/mxml/2009"
                       xmlns:s="library://ns.adobe.com/flex/spark"
                       xmlns:mx="library://ns.adobe.com/flex/mx"
                       xmlns:customerservice="services.customerservice.*"
                       xmlns:valueObjects="valueObjects.*"
                       currentState="State1">
    <fx:Script>
        <![CDATA[
            import mx.controls.Alert;
            import mx.events.FlexEvent;
            protected function dataGrid_creationCompleteHandler(event:FlexEvent):void
                getAllCustomerResult.token = customerService.getAllCustomer();
            protected function button_clickHandler(event:MouseEvent):void
                var customer2:Customer = new Customer();
                customer2.id = parseInt(idTextInput.text);
                customer2.name = nameTextInput.text;
                customer2.email = emailTextInput.text;
                currentState = "Test";
                createCustomerResult.token = customerService.createCustomer(customer2);
        ]]>
    </fx:Script>
    <s:states>
        <s:State name="State1"/>
        <s:State name="Test"/>
    </s:states>
    <fx:Declarations>
        <s:CallResponder id="getAllCustomerResult"/>
        <customerservice:CustomerService id="customerService"
                                         fault="Alert.show(event.fault.faultString + '\n' + event.fault.faultDetail)"
                                         showBusyCursor="true"/>
        <valueObjects:Customer id="customer"/>
        <s:CallResponder id="createCustomerResult"/>
        
    </fx:Declarations>
    <s:DataGrid id="dataGrid" includeIn="State1" x="330" y="10" width="392"
                creationComplete="dataGrid_creationCompleteHandler(event)" requestedRowCount="4">
        <s:columns>
            <s:ArrayList>
                <s:GridColumn dataField="id" headerText="id"></s:GridColumn>
                <s:GridColumn dataField="name" headerText="name"></s:GridColumn>
                <s:GridColumn dataField="email" headerText="email"></s:GridColumn>
            </s:ArrayList>
        </s:columns>
        <s:typicalItem>
            <fx:Object id="id1" email="email1" name="name1"></fx:Object>
        </s:typicalItem>
        <s:AsyncListView list="{getAllCustomerResult.lastResult}"/>
    </s:DataGrid>
    <s:Form includeIn="State1" defaultButton="{button}">
        <s:FormItem label="Id">
            <s:TextInput id="idTextInput" text="{customer.id}"/>
        </s:FormItem>
        <s:FormItem label="Name">
            <s:TextInput id="nameTextInput" text="{customer.name}"/>
        </s:FormItem>
        <s:FormItem label="Email">
            <s:TextInput id="emailTextInput" text="{customer.email}"/>
        </s:FormItem>
        <s:Button id="button" label="CreateCustomer" click="button_clickHandler(event)"/>
    </s:Form>
    <s:Form includeIn="State1" x="0" y="204">
        <s:FormItem label="CreateCustomer">
            <s:TextInput id="createCustomerTextInput" text="{createCustomerResult.lastResult as int}"/>
        </s:FormItem>
    </s:Form>
</s:WindowedApplication>

IPhone 5 cellular data services failing

ISSUE/SYMPTOMS: iPhone 5 ONLY: Cellular Data stops intermittingly, cellular data locks up without warning, Wi-Fi data connection not working on occasion, iCloud contacts, calendar and reminders not updating, Find My Phone not working, mail or Internet not available or server time-outs. No error messages though. All of these are symptoms of no data service. Problems seem to be related to iPhone 5 failing to switch between LTE and 4G or 3G data services on AT&T.
My iPhone 5 32GB AT&T version (iOS 6.0.2) along with my clients and family using iPhone 5 in the state of Oklahoma are having this issue on their AT&T iPhone 5's: no cellular data connection re-established if at anytime the LTE connection is lost or weak. As with iPhone's prior to iPhone 5, the iPhone 5 is supposed to drop down to the next tier of data service and re-connect to cellular data service when the higher speed cellular data service is not available. Apparently this is not working well on the iPhone 5.
What led me to research this LTE issue was that my iPhone was not syncing on iCloud with contacts, calendars and reminders with my other iOS devices. Other times this issue became apparent was when iMessage quit sending and receiving until I would reboot my iPhone (sometimes it would finally send the message as a “text message”). When I had these problems I also found out I was not getting any cellular data service for Internet browsing, mail, Maps, Find My iPhone, etc. This would happen without notice. In other words I would not receive any notice or error message that data service had stopped other than the fact I was not receiving any mail, iMessages, or iCloud sync updates. My only resolution was to reset or reboot my iPhone several times a day, and that would resolve it about 70% of the time.
I have talked to Apple Support on 2-3 occasions in the last week and AT&T Support twice in the last 2 days. If it is really true, only the AT&T Technical Support Advisor informed me of a nationwide issue relating to iPhone 5 and LTE: iPhone 5's are not re-connecting to 4G or 3G cellular data service once the LTE data connection is lost or dropped... the voice calls continue to work, but cellular data service fails and stays locked up without an error message until the customer reboots the iPhone.
Obviously this is very unacceptable. We depend on these data services and at minimum need to know when it stops working instead of finding out from a phone call that someone sent us an important email or something.
The AT&T representative also said that both AT&T and Apple are aware of and are working on the issue as it is a nationwide problem with iPhone 5 and LTE. The Apple Support Advisors I talked to made no mention of this "known" issue. AT&T said that it is partly AT&T responsibility because the capacity of LTE is overloaded and cellular data connections are dropping because of the lack of coverage and/or capacity. They actually refunded my data service for a whole month in apology for the inconvenience (I did not even ask for that--I just want my data service to work). But they also said that Apple has responsibility in this issue because the iPhone 5 should drop down and re-connect to the next lower tier of data service when LTE is not available or lost; instead, it is locking up somehow or it still thinks it is connected to LTE when it is actually not. I don't know how accurate these statements are, but my problem is real.
TEMPORARY WORK-AROUND / FIX FROM AT&T: Disable LTE on the iPhone 5. Or when you figure out that data is not coming to your iPhone, use Airplane Mode ON/OFF for a few seconds to force re-connection to a tower without rebooting the iPhone. You can Disable LTE on the iPhone 5 in SETTINGS/GENERAL/CELLULAR. I have disabled LTE on my iPhone 5 and have not had any of these cellular data issues since.
Disabling LTE is not acceptable either, but it is working. At least I seem not be losing connection or locking up without knowing it. In my office over the course of a day, my iPhone 5 will jump back and forth on LTE and 4G sitting in the same place. Disabling LTE has stopped this and the problem, but the iPhone 5 should switch cellular data services seemlessly just like the phone switches towers on a phone voice call seemlessly (most of the time).
WI-FI ALSO STOPS WORKING SOMETIMES AFTER THIS LTE disconnect / lock-up issue: That has been my experience along with my clients and family as well. If you use Wi-Fi a lot on your iPhone it will hide this LTE issue until you leave your Wi-Fi and get on LTE and then drop LTE (silently) and then go back to your Wi-Fi. My experience has been I have to reboot the iPhone to even get Wi-Fi working again after that happens.
I do not know if some of these comments and analysis are really accurate or valid or not... all I know for sure is since I upgraded my iPhone to the 5 along with my other family members and clients, we have had "no data" on many occasions and are continually rebooting our iPhones and looking for what is wrong.
My questions to the support community are these:
     1. Is anyone else having this issue? Or is it just me and my few? Maybe a lot of people do not realize they are not getting their data because they are on Wi-Fi most of the time or they are just rebooting and not trying to identify the real problem. AT&T said it was nationwide iPhone 5/LTE issue. Anyone else heard that from either Apple or AT&T?
     2. Is this an iPhone 5 / Apple issue or is AT&T solely responsible? Or is it both? Where do we get a solution??? Is AT&T LTE holding false connections with iPhone 5 or is the iPhone 5 failing to recognize a dropped LTE cellular data connection and then failing to attempt to re-connect with 4G or 3G?
     3. Did I miss where this issue is posted? I searched Apple Support and Communities and did not get any hits. Any updates or further insight on the issue? Any other fixes other than Disabling LTE?
      4. If this is in fact a real issue belonging in part to the iPhone 5, we need to escalate Apple’s attention to it.
Thanks in advance for your help and feedback.

Thank you fellow users and experts for your feedback and updates. Sorry about the large font on the original post... accidental via cut and paste.
I have escalated the issue with both Apple and AT&T. I actually got senior level troubleshooters from both Apple and AT&T on the phone at the same time... rare moment. Here are the key points of the update:
     1. AT&T did NOT confirm the earlier statement by another AT&T Technical Support Agent that this was an emerging nationwide issue about iPhone 5 and LTE losing data connection and not reconnecting at a lower level or re-connecting to LTE once the signal came back. So that earlier statement was not accurate as suspected by all of us. The senior tech at AT&T said he has seen this issue sporadically over the last month or so, but only with about 3-4 customers. He said it seems to be location or phone dependent (some phones not all phones).
     2. The Apple Tech was satisfied that all that could be done to eliminate my issues possibly relating to my instance of software / iOS had been accomplished except erasing my iPhone and restoring as a new phone (I have avoided this inconvenience with the argument that other family/clients with the iPhone 5 have had the same problem).
     3. AT&T went so far as to examine which towers I had been connecting to over the last week and looked at other technical data that could possibly explain the issue. I now know I have 3 towers that provide LTE within 4 miles of my home/office, one within a half mile. But so far there is nothing to explain or even properly identify the issue. AT&T offered me to take my phone to an AT&T store, try to force replicate the problem there, if so, the store would put my SIM card in a brand new iPhone 5 (just to test) and try tor replicate the problem again. If replicated on a new phone, there is a deeper issue; if resolved on a new phone, the answer is obvious. I have not taken the time to do this yet.
     4. On Friday, Jan 4, 2013 while talking and between the tech support calls (on a different phone), I was able to re-create the problem 2 separate times in my home/office by forcing my iPhone to weaken its connection to service (burying it under electronic gear) and then waiting a few minutes, then trying to browse the Internet--no data service unless I manually reset the connection. I am only able to cause the issue to occur if there is at least 15 min of idle time after a weak signal condition AND only if I don’t completely lose a connection to cellular voice service. It seems that if you go down to NO SERVICE the phone will do new a search and keep searching until reconnects to LTE or other signals correctly, but a weak connection seems to be strong enough for voice service but can sometimes cause the LTE data service to stop without reconnecting to LTE, 4G or 3G unless I manually intervene. It also seems that idle time with a weak connection is also necessary to re-create the problem manually. Since Friday, I have not been able to re-create the problem. This has been an intermittent problem, so who knows.
FYI, I have never had this problem with my new iPad (also on AT&T LTE) that has been with me when the iPhone fails to have data service, but my iPad is never in my pocket or other places with perhaps less signal.
Again, if you are connected to Wi-Fi on your iPhone 5 most of the time, you may never notice this issue if you are even having it.
So far no progress on the real issue or resolution, but both Apple and AT&T have put forth very admirable effort.
If you or others you know are having this issue, please take the time to post a reply to this issue. Thank you.

How to auto scroll a table to last row when using Active Data Service? 11g

Hi all,
Has anyone got any experience with the ADF Active Data Service?
I am using an af:table in combination with the ADF Active Data Service and I want the table to scroll to the latest row when new data arrives.
It is basically a simple setup:
The value attribute of my table points to a bean that extends CollectionModel and implements ActiveDataModel. This works perfectly. A soon as I receive new data in my bean, the table is automatically updated (e.g. a new row is inserted). I use JDev version: 11.1.1.3
The problem is that I can not get the scroll bar to move down to the last row automatically when new data arrives. The auto scroll only works for the client that actually performs a submit. In other words the person that submits the new data, will see his scrollbar move down, this is because I added the following code:
RowKeySet rowkeysset = chatTableBinding.getSelectedRowKeys();
rowkeysset.clear();
rowkeysset.add(getRowKey());
AdfFacesContext.getCurrentInstance().addPartialTarget(this.chatTableBinding);
This does not work for the clients that receive the new data via the Active data model. Apparently the active data service partially refreshes the table, but not in such a way that it sets the selected row to the last row?
My table definition:
<af:table value="#{pageFlowScope.chatBean.instantMessagingChatwindowBean}" var="row"
id="t1" columnStretching="last" rows="10"
styleClass="AFStretchWidth" autoHeightRows="10" contentDelivery="immediate"
horizontalGridVisible="false"
verticalGridVisible="false"
disableColumnReordering="true" displayRow="last"
rowSelection="single"
binding="#{pageFlowScope.chatBean.instantMessagingChatwindowBean.chatTableBinding}"
inlineStyle="height:80px;">
p.s.
The table is used to show incoming chat message.
I am building a chat client (taskflow) in a Webcenter application. The concept is similar of that presented by Lucas Jellemain in his blogpost on building a Google Talk Client http://www.oracle.com/technetwork/articles/jellema-googletalk-094343.html

Dan,
This is a thanks for posting your findings. You saved me quite some time.
<af:selectBooleanCheckbox id="showOnlyActiveSubscriptions" selected="true"
label="Show only active services:"
value="#{servicePortfolioBean.showOnlyActiveSubscriptions}"
autoSubmit="true" />
<af:table binding="#{servicePortfolioBean.serviceTable}" ...
partialTriggers="showOnlyActiveSubscriptions">
Of course, when I add a "ValueChangeListener" to the selectBooleanCheckbox, the PPR stops working. :( I wonder why?

Master Data Services Add-in for Excel Issue

I am trying to configure MDS in the Production server. I am running into isssues.
(I was able to do the whole process successfuly in my local system - Versions are same in the local and server - Only difference is local machine is windows 7 server is Windows 2008 R2)
I have installed SQL server 2012 Enterprise Version SP1. I am able to browse the MDS URL. User has got full permissions. When I try to access the MDS via Excel I get the below error.
Can any one help me please I have spent days on this withou any joy.
Error message
TITLE: Master Data Services Add-in for Excel
An error occurred while receiving the HTTP response to
http://MYIPADDRESS/mds/service/service.svc/bhb. This could be due to the service endpoint binding not using the HTTP protocol. This could also be due to an HTTP request context being aborted by the server (possibly due to the service shutting down). See
server logs for more details.
ADDITIONAL INFORMATION:
The underlying connection was closed: An unexpected error occurred on a receive. (System)
Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host. (System)
An existing connection was forcibly closed by the remote host (System)
BUTTONS:
OK
Bn

I have finally found a solution for this problem! Every time I opened Excel (unless I ran as administrator) I would have to activate the MDS add-in; this was time-consuming and annoying. It seems like there was no solution posted online anywhere! Well
after much aggravation, I have finally found a solution:
Fixing the Microsoft MDS Excel Add-In so it Stays Enabled
Press the Start button (Windows button)
In the search bar type “REGEDIT”
Open regedit.exe
A pop-up will ask permission for the Registry Editor to make changes to the computer, select Yes.
In the Registry Editor expand HKEY_CURRENT_USER
In the HKEY_CURRENT_USER folder, expand in the following order: Software -> Microsoft -> Office -> Excel -> Addins
Select Microsoft.MasterDataServices.ExcelAddIn
Double-click on LoadBehavior in the right panel
In the Edit Value popup, change the value to
Press OK
Exit the Registry Editor
The excel add-in should now be active anytime you open Excel. If multiple errors occur while using the add-in, the Load Behavior may change back to 0. If that occurs simply follow these steps so the add-in will be active when Excel starts up.
I hope this helps some of you avoid the long hours of trying to find a solution to this silly problem.
Cheers!
Tony

Data Services ORA-00942 table does not exist. Source/Target same DB

Error: u201CORA-00942: table or view does not existu201D
Source & Target Datastores in same Oracle DB but different User/Schemas.
I set up the Data Services Tutorial Source & Target Data bases in ONE Oracle DB using a separate User/Schema for the ODS source DB & TARGET Source DB.
I then created
- Source datastore for the ODS DB User/schema
- Target datastore for the TARGET DB user/Schema.
I have no problem reading flat files & writing to TARGET datastore tables.
However, when I read the ODS datasttore source table CUSTOMER & write to the TARGET datastore target table CUST_DIM I get an error: ORA-00942: table or view does not exist.
I can query the table contents from the Data Flow & see the data in the source data & see the empty target table.
So the tables exists & there is no security issues from the DS Designer.
I did find note 1189910 - ERROR: Error Description: An error occurred while creating the result data - Data Insight XI
Cause
Multiple engines are being run against the same metadata repository.
Resolution
Verify that only one engine is being run against a single metadata repository.
Has anyone seen this error?
Or has anyone created a 2 data stores on the SAME DB, but to different User/Schemas?
Thanks
Jay Roble

since you are accessing 2 schema which are on same oracle database, DS engine is trying to optimize and generating an INSERT INTO ... SELECT clause. Since its the same DB, DS Engine is doing a implicit linking of the datastores
you can see the SQL generated from the Designer, drill down into DF, from the Menu select Validation ->Display Optimised SQL
to disable this implicit linking, right click on the Dataflow, select properties
in the properties window, unselect the the option "use database links"

Flex Data Services does not see remote methods in extended ColdFusion component.

I have created a remote service base component as a AModelService.cfc file. I extend that file to make my ModelService.cfc. When I configure the ColdFusion data service and point to ModelService.cfc and click next, I don't see any remote methods (there are none explicitly defined in the component) in the Service Operations window.
If I go back and point to AModelServide.cfc, the parent component, and hit next, I see all the remote methods that are defined in the parent component. So, either I am doing something wrong, or Data Services does not look at methods up the cfc prototype chain, which from an OOP standpoint means that instead of say creating one restful base class and being nice and DRY you can't. I.e. not OOP for data services. Is this a bug, or what?
Anybody get data services to work with extended service components?
Mark

Thanks for the reply. Yes, I did compile all the Java and it
works OK with a simple Java program. It just will not work in a
Flex application.
The java classes are:
RRA:
package blah.myPackage;
import java.util.List;
import java.util.Collection;
import flex.data.DataSyncException;
import flex.data.assemblers.AbstractAssembler;
class RRA extends AbstractAssembler
public Collection fill( List fillParameters )
RRS service = new RRS();
return service.getSome();
RRS:
package blah.myPackage;
import java.util.ArrayList;
import java.util.List;
import java.sql.*;
import flex.EORS.*;
class RRS
public List getSome()
ArrayList list = new ArrayList();
String str = "bob";
RR rr = new RR(str);
list.add(rr);
return list;
RR:
package blah.myPackage;
class RR
private String name;
public RR() { }
public RR(String name)
this.name = name;
public String getName()
return this.name;
public void setName(String name)
this.name = name;
I started with something that retrieved data from a database
but watered it down just to try and get some kind of communication
between Flex and Java.

Why would I need to use LiveCycle Data Services in a Flex app?

I cannot figure out what additional functionality is provided by using LiveCycle Data Services in my Flex apps. I cannot get a clear understanding of how using LiveCycle Data Services would benefit my applications. Does someone out there use LiveCycle Data Services? If so, what do you do with it in Flex?
Thanks!

- data push for publish/subscribe implementations
User has to do nothing to get updated information. You push it to their machine when new data is available, like Yahoo finance updated quotes.
- data paging
You don't want to display one million rows in your datagrid at once. Get a batch of data, if the user scrolls down, get the next batch, etc.
- server side clustering
One server does not get overloaded. High traffic sites have their large number of concurrent connections managed more efficiently.
- JMS services
JMS is a powerful technology for messaging throughout an application, and LCDS makes it much easier.
- RTMP tunneling
Allows the use of the RTMP protocol in LiveCycle Data Services applications. Makes it easier to traverse firewalls and proxies appropriately that currently prevent direct RTMP client connections to the server.
If this post answered your question or helped, please mark it as such.

Question - new to BO Data Services Designer - how to automatically transform varchar column data to upper(varchar) across all columns in a table?

Hello -
New user to BO Data Services Designer. Company is using Data Services Version 12.2.
I have many tables that all need the same transformation- converting varchars fields to upper(varchar) fields
Example:
I have a table called Items. It has 40 columns, 25 of which are of type varchar.
What I have been doing is ....
I make the Item table as the source table then create a Query transform that is then attached to a new target table called - ITEMS_Production.
I can manually drag and drop columns from the source table to the query and then in the mapping area I can manually type in upper(table_name.column_name) or select the upper function and then select the table.column name from the function drop down list.
Obviously, I want to do this quicker as I have to do this for lots and lots of tables.
How can set up Data Services so that I can drag and drop an upper transform quickly and easily or automate this process.
I also know Python-Java so am happy to script something if need be.
the logic would be something like -
if there is a column with a type varchar, add the upper() transformation to column. Go to next column.
Excited to be using this new tool-
Thanks in advance.
Ray

Use the DS Workbench.

Data services stop working after updating to new OS version for Q10

I am from Qatar, after i updated my device ( Q10 SNQ100-3 ) to new OS ( 10.2.1.537 ), the mobile data services stopped working, but it works everytime I connect to wifi. This is the same with Z10. Please need help.

Hi and Welcome to the Community!
With a strong carrier network signal (e.g., not merely WiFi), I suggest the following steps, in order, even if they seem redundant to what you have already tried (step 1 should result in a message coming to your BB...please wait for that before proceeding to the next step):
1) Register HRT
KB00510 How to register a BlackBerry smartphone with the wireless network
Please wait for one "registration" message to arrive
2) Reboot
Pre-BB10 Devices ONLY. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes.
BB10 Devices. Hold the top button down until the counter reaches zero. Wait for the device to be fully shut down (e.g., nothing at all displayed on the screen, no LED lights, etc.). Hold the top button until the red LED is lit. Wait through the full boot-up process. IF this fails, you can attempt the battery-pull method above, but it is normally NOT recommended unless nothing else works.
See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Hopefully that will get things going again for you! If not, then you should contact your mobile service provider for formal support.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

6 month on.. My observations on Data Services vs SSIS

Hi all,
I'd like to share some observations on my first six months working with Data Services. I have previously worked with SSIS for several years and have some minor experiense with Datastage also.
Firstly, let me say that I am largely happy with Data Services. There are pro's and Cons, but for an SAP ECC shop like us, it solves more problems than it causes.
The positives:
The ability to call SAP extractors directly, saves huge amounts of time and money for us. We can do in DS in a day what would take weeks if we have to use openhub and SSIS combined.
The Query transform is really flexible and does in one step what would take several in SSIS.
DS is more tolerant of metadata changes.
Template tables are a great feature that support quick turn-around.
The negatives:
Crashes = DS 4.0 is a buggy tool. Everytime I loose network connectivty it crashes. It crashes randomly at other times as well. I'd say once every 2 days would be about the average between crashes. SSIS isn't perfect, but is much more stable than that.
Debugging - SSIS's visual debugging is far superior to what DS has
Attitude - There is a certain degree of arrogance amongst SAP/BO consultants I have dealt with. I have heard phrases like 'SSIS is not an ETL tool' and SSIS just runs SQL' several times. That's a load of BS. Both tools are quite similar in many ways, and the reality is DS does a lot more push-down to the database than SSIS does out of the box.
Community - SSIS has a great community. If I ask a question in an SSIS formum, I know i'll get an answer by the next day. Here, I'd say half my questions are never answered. Micrsoft have several people monitoring the forums at all times and they do a great job of this.
lock-down - With SSIS, I can download a free eval of SQL Server (or buy a dev only copy very cheaply), install it on my PC at home and try things out. With DS, thats not an option.
No 3rd party extensions - there are lots of 3rd party extensions available for SSIS. I've yet to find any for DS.
This is not meant to to be a negative post; i'd be interested in hearing other's point of view on this.
Thanks.
Leigh.

If you need to get data from ECC, then data services is probably your best option. But it is a big investment.
Conceptually, DS is similar to SSIS - think if SSIS as a basic version ( I worked with SSIS before DS, and I wouldn't ever go back). I would say you will need 6 months to get up to speed with it enough to be able to build production ready easy to support code. You will probably have the quick and dirty stuff going in a few weeks. We bought in a consultant to teach us on the job for 3 weeks, so I never had any formal training, but that would probably be a good idea.
There is no point keeping SSIS if you have DS, so the plan would be to migrate over time.
The other option is to look at SAP rapidmarts. These are basically pre-built datamarts for SAP - you load them into data services, change the connection details and run them ! If you went this route, you could use SAP consultants to set it up, but you would still need DS skills to support it.
Either way, and independent of DS, you will need some serious expertise on the SAP side to help you. Even a data services expert couldn't necessarily build a solution based on ECC without a subject matter expert to help.

Master Data Services Add-in will not stay enabled

Using Excel 2013 x64 with the 2012 MDS add-in.
The master data services add-in works but when I shut down Excel, the add-in is soft disabled and I have to re-enable it every time I start Excel. I've tried disabling everything and then just enable MDS and that doesn't help.
How can I troubleshoot this? I can't roll out 2013 to my users if this problem persists.

I have finally found a solution for this problem! Every time I opened Excel (unless I ran as administrator) I would have to activate the MDS add-in; this was time-consuming and annoying. It seems like there was no solution posted online anywhere! Well
after much aggravation, I have finally found a solution:
Fixing the Microsoft MDS Excel Add-In so it Stays Enabled
Press the Start button (Windows button)
In the search bar type “REGEDIT”
Open regedit.exe
A pop-up will ask permission for the Registry Editor to make changes to the computer, select Yes.
In the Registry Editor expand HKEY_CURRENT_USER
In the HKEY_CURRENT_USER folder, expand in the following order: Software -> Microsoft -> Office -> Excel -> Addins
Select Microsoft.MasterDataServices.ExcelAddIn
Double-click on LoadBehavior in the right panel
In the Edit Value popup, change the value to
Press OK
Exit the Registry Editor
The excel add-in should now be active anytime you open Excel. If multiple errors occur while using the add-in, the Load Behavior may change back to 0. If that occurs simply follow these steps so the add-in will be active when Excel starts up.
I hope this helps some of you avoid the long hours of trying to find a solution to this silly problem.
Cheers!
Tony

Thunderbolt data service down

Similar Messages

Maybe you are looking for