Thunderbolt display crack

I was unplugging my laptop from my Thunderbolt Display, literally getting ready to put it in its box to return it, and the laptop slid to the side of its elevated platform and bumped the side of the screen. It cracked the lower corner of the screen a very small bit on the outer edge of the bezel. its less than 1/4" and doesn't effect the display at all but since my laptops thunderbolt port doesn't work the display is useless to me unless someone has a solution to using it with a pc. I'm just curious what my options are. I just purchased it last week

Cannot help you with a use for the display but the glass screen is held on with magnets so easy to change out but not sure what the cost would be. I have seen some defective units on ebay for parts.

Similar Messages

Thunderbolt display: devices not discovered after using Mini DisplayPort–to–VGA adapter

I have an interested problem related to using my MacBook Air in clamshell (closed) mode, connected to a Thunderbolt display. The problem appears to be related to moving my MacBook air between my office and my home.
At the office, I use the MacBook Air with an external VGA display, connected via the Mini DisplayPort–to–VGA adapter. At home, I use the MacBook Air together with a Thunderbolt display. An Apple USB keyboard is also connected to the display.
Mini DisplayPort–to–VGA adapter implicated
The following sequence of events causes the problem to occur:
Use the MacBook air (open) together with a VGA display, connected via a Mini DisplayPort–to–VGA adapter (depicted at right);
Put the MacBook Air to sleep by closing the lid, and disconnect the Mini DisplayPort–to–VGA adapter (I am not sure if the order of these two steps is significant—I usually perform them almost simultaneously when packing up my MacBook Air and getting ready to leave the office); and
With the MacBook Air still closed, connect it to a Thunderbolt display with a connected USB keyboard.
At this point, I would expect to be able to wake up the MacBook Air by tapping on the space bar of the keyboard. However, what I have observed is that this does not wake the MacBook Air.
I can wake the MacBook however by moving or clicking a Bluetooth mouse that is paired with the MacBook Air.
At this point, although the MacBook Air is awake, and the display is working, the USB keyboard connected to the display still does not work. This is the problem, in a nutshell.
Unplugging the USB keyboard from the display, and plugging it back in causes the MacBook Air properly to identify the keyboard.
I used Apple System Profiler to save a list of identified devices at two points in time:
Immediately after waking the MacBook Air by moving the Bluetooth mouse (at which point the USB keyboard was not working); and
After unplugging and plugging in again the USB keyboard (at which point the USB keyboard worked fine).
Many devices are enumerated in the second list that are missing from the first. For example:
Keyboard Hub@fe110000 <class IOUSBHubDevice, id 0x1000378ef, !registered, !matched, inactive, busy 3 (37993 ms), retain 6>
AppleUSBHub <class AppleUSBHub, id 0x1000378f2, !registered, !matched, inactive, busy 1 (37987 ms), retain 6>
IOUSBInterface@0 <class IOUSBInterface, id 0x1000378f4, !registered, !matched, inactive, busy 1 (37986 ms), retain 6>
Keyboard Hub@fe110000 <class IOUSBHubDevice, id 0x1000378f6, registered, matched, active, busy 0 (7 ms), retain 10>
AppleUSBHub <class AppleUSBHub, id 0x1000378f9, registered, matched, active, busy 0 (1 ms), retain 9>
IOUSBInterface@0 <class IOUSBInterface, id 0x1000378fb, !registered, !matched, active, busy 0, retain 7>
Apple Keyboard@fe112000 <class IOUSBDevice, id 0x1000378fd, registered, matched, active, busy 0 (112 ms), retain 11>
and many child devices…
Using the Mini DisplayPort–to–VGA adapter appears to be a necessary step to causing this problem to occur. If I merely disconnect the MacBook Air from the display, let it go to sleep, and then reconnect it again, the USB keyboard will work immediately and can be used to wake the computer from sleep.
Some devices are discovered even when the computer is in sleep mode. This is how it should work.
The problem appears to be that when a Mini DisplayPort–to–VGA adapter has been used since the last time the computer was connected to a Thunderbolt display, the MacBook air does not discover devices completely when it is again connected to the Thunderbolt display while in sleep mode.
Can anyone else reproduce this problem?

Hi glraczon.support,
It sounds like the external display you are using (projector) operates at a smaller resolution than your MacBook Pro. You may want to configure the display preferences in System Preferences for the external projector.
Here is an article that may help you with that process:
OS X Mountain Lion: About the Display pane of System Preferences
http://support.apple.com/kb/HT5369
Thanks,
Matt M.

Is it possible to connect an external USB 2.0 hard drive to a Thunderbolt Display?

Hello,
Is it possible to connect an external USB 2.0 hard drive to a Thunderbolt Display and back up a MacBook Air to the external hard drive using Time Machine?
I intend to connect my MacBook Air to the Thunderbolt Display using a Thunderbolt cable.
I would also like to connect my printer via USB 2.0 to the Thunderbolt Display. Will this also work?
Effectively using the Thunderbolt Display as a USB hub or docking station.
Regards,
Ben

Ok, thanks.
My 1 cable to ThunderBolt Display objective
MacBook Air -> (via 1 x Thunderbolt cable) -> Thunderbolt Display -> (via 1 x USB cable) -> USB 2.0 external hard drive
I would like to know if this configuration is possible and Time Machine will run correctly.
Your 2 cable suggestion (I think)
MacBook Air -> (via 1 x Thunderbolt cable + 1 x USB cable) -> Thunderbolt Display + USB 2.0 external hard drive
This configuration requires 2 cables to disconnect/reconnect from my MacBook Air.

MBP Bootcamp install of USB Windows 7 , Thunderbolt Display

We need support from APPLE! BootCamp
Here are my issues.
Like many users, I must abandon the marvelous os x, and head to the darkside - Windows 7 for work.
I have a MBP early 2011. I must use Bootcamp, because of the resource hogging the 3d CAD programs I use. have tried to in the past with VMWARE, Parallels ect. with no luck
I have a Corsair Force GT ATA 120 gb SSD III, installed and my optical drive removed to accommodate my original Hitachi.
Remember, not to Install that Hitachi drive, until you have used a CD only install of windows 7 onto the SSD.
Why?- You can not boot from a USB disc that I am aware of, or use an external optical drive case, for your superdrive.
This is not ok, we need the capability to install windows 7 from something other than a CD. I went to reformat my SSD I was forced to open up my MBP case again. to reinstall the Super drive. Install Windows 7, then remove my superdrive and reinstall my 500gb Hitachi.
This is a royal, pain in the butt.
If a mac air has the capabilities of installing windows 7 from a usb APPLE, please give same rights to MBP.
Additionally, my osX runs like absolute garbage on the SSD, I rarely if ever use it because of the constant pinwheel I receive, I have researched this error, with
little or no luck, using apps like TRIM seem not to help.
I also own a thunderbolt display, and the fact that there is no support on connecting it without restarting the computer is also an issue.
Bootcamp Development -should add in fan speed Control,

Buddah1200 wrote:
We need support from APPLE! BootCamp
Here are my issues.
Like many users, I must abandon the marvelous os x, and head to the darkside - Windows 7 for work.
I have a MBP early 2011. I must use Bootcamp, because of the resource hogging the 3d CAD programs I use. have tried to in the past with VMWARE, Parallels ect. with no luck
I have a Corsair Force GT ATA 120 gb SSD III, installed and my optical drive removed to accommodate my original Hitachi.
Remember, not to Install that Hitachi drive, until you have used a CD only install of windows 7 onto the SSD.
Because you will need the internal superdrive to install Windows.

How can I tell my MacBook Air to automatically detect my Thunderbolt Display?

I have a brand new MacBook Air (13", mid-2011) running 10.7.2 (and all updates) and Thunderbolt Display (with firmware 22.2, the latest)
When I plug the thunderbolt plug into the port, I expect the MBA to recognize the display and automatically start using the display based on the last settings (arrangement, etc.) This is how every other display (Apple or not) has worked with a MacBook I've owned. This is one of the nice little touches that I really appreciate about Apple products.
What actually happens when I plug in the thunderbolt display is.... nothing. The MBA will work happily as if there is no external display plugged in until I bring up the Displays control panel and "Detect Displays". This is contrary to how it worked in the past and based on that experience, I consider the current behavior to be a bug.
Is there some setting I'm missing to make this work properly? It is pretting annoying to have to many times a day (in the morning and every time I take my MBA away from my desk). Is this a known issue that Apple will be fixing soon?
Thanks,
Paul Philion
Acme Rocket Company
Mac Owner Since 1985

It's definitely not supposed to work like that...when you plug the display in, it should just turn on and adjust your displays. It works like that on my MBP. Kind of a silly question, but do you have the MagSafe from the display plugged in your MBAir too? Thats a requirement. Beyond that, it should "just work."
Not sure if there is some setting to enable...i haven't seen it. Call to support?

Cinema display VS Thunderbolt display

Hi!
I'm about to start a bidding on an Apple Cinema display 24" bought in july 2010. Now, besides general opinions about this display, are there any fundamental differences between the Cinema display (CD) and the newer Thunderbolt display (TD)?
What I already know is that the TD has 3xUSB, 1xFireWire, 1xThunderbolt and 1xEthernet on the back where the CD only have 3xUSB. Also, the TD only need the thunderbolt cable to the (i e) MacBook to function where the CD need to have the USB cable in addition to the cinema display cable connected to function.
Have I got that right?
I have the newest MacBook Pro with thunderbolt output, but do I still need the USB cable to get the 3xUSB hub on the display? Or is it enough with the cinema display cable from the display?
Hope I didn't make it to complicated to read =)
The price right now is almost 500$.
Oh, that's right - one more thing! I've read a little about compatiblity with different displays and computers. My MacBok Pro has thunderbolt output, but is it still possible to connect the Cinema display that does NOT support thunderbolt?
Jonas

I googled my question and found this article:
http://reviews.cnet.com/8301-13727_7-20043524-263.html
I quote the article:
"The new port is backward compatible so it can still be used to connect to DisplayPort devices; however, only the new port can be used to connect to Thunderbolt devices.
This means that while you can physically connect a Thunderbolt device to a Mac with DisplayPort, the device will not work, but if you connect a DisplayPort device to a Mac with Thunderbolt, then the device will work."
Helpful picture:
http://i.i.com.com/cnwk.1d/i/tim/2011/03/15/ThunderboltChart_270x130.png
So if you believe in this, I actually can use the Cinema display with my MacBook with thunderbolt port. Or am I getting this all backwards?
Jonas

How do I use a MacBook with a Thunderbolt Display?

I have a new Thunderbolt Display which I use with a new Mac Mini. If possible, I would like to attach my 2008 era MacBook to the Thunderbolt Display to take advantage of the bigger screen. I understand that MacBook doesn't have Thunderbolt and the Thunderbolt Display requires it, but...isn't there maybe, just maybe, some sort of Thunderbolt to USB2 cable or something that might make this work?
Help me, Obi-won, you are my only hope.

There are Thunderbolt adapters you can use for the type of video port on your MB:
Display
1 - Mini-DVI (VGA, Composite and S-video with adapter)
But you may need to upgrade its OS X version at least to Snow Leopard.
Upgrading to Snow Leopard
You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mavericks if your computer meets the requirements.
     Snow Leopard General Requirements
       1. Mac computer with an Intel processor
       2. 1GB of memory
       3. 5GB of available disk space
       4. DVD drive for installation
       5. Some features require a compatible Internet service provider;
           fees may apply.
       6. Some features require Apple’s iCloud services; fees and
           terms apply.

How to charge mid 2011 macbook air battery using Thunderbolt display

While trying to organize all my computer miscellaneous (cords, adapters & so on), I came across an adapter on a little card with the comment, "For use with your Thunderbolt Display and Mac with MagSafe 2 port." Appears to be for charging my mid 2011 MacBook Air via the Thunderbolt Display -- what might be the advantages/disadvantages in doing so? I found the info. in the product manuals to be pretty skimpy about this.
Thanks,
Linda

So, I guess the adapter came with the display just in case I had a compatible Mac. I should have noted that on the card. Now, about the rest of the stuff in my Apple mystery box...that's for another day.
Thanks, seb101, for your quick reply!

Can a Mac Pro (2.66 ghz duel core) be upgradable to support Thunderbolt displays and other devices.

Can a Mac Pro (2.66 ghz duel core (4cores)) be upgradable to support Thunderbolt displays and other devices. Does this need to be done through the Graphics card expansion or a additional card to be inserted?

No. There is no way to upgrade any Mac Pro older then the cylindrical 2013 Mac Pro to ThunderBolt.
The requirements of Thunderbolt require a totally redesigned motherboard and chip set rather any plugin cards. These motherboard were never developed for older Mac Pros.

How to connect two DVI screens to Thunderbolt Display's Thunderbolt Port?

Hi everyone,
I have a new MBP and an external Thunderbolt Display. The Thunderbolt Display itself has a Thunderbolt port, and I was wondering if there is anyway to connect to DVI screens to that. My goal is to have the Thunderbolt Display and 2 x 24" Samsung DVI screens connected to my MBP.
Alternatively, has anyone had success using a third party device like the Matrox 2 go to drive multiple monitors from the usb port?
Thanks,
Dave.

You could try a TB>DVI adapter (here's one from Monoprice) but I don't know that it will work - I'm thinking that you could have at least one of your Samsung displays use it. You may also want to see if you can find a HDMI>DVI adapter for your second Samsung display - something like this?
I know that I've seen three monitor set-ups on YouTube - but I'm not sure what was connected to what. Easy enough to daisy-chain ATDs but it gets a bit tougher when utilizing HDMI ports, etc., and I'm not sure about the GPUs ability to drive all three displays.
Oops - sorry - strike that second paragraph - I thought that you were running a Retina display MBP...
Clinton
Message was edited by: clintonfrombirmingham

How to connect VGA Monitor via Thunderbolt Display

I've been using my Macbook Air mid 2013 with a Samsung monitor connected via the Mini Display Port to VGA adapter. I've now bought a 27" Thunderbolt display, which I've connect to my Mac, and assumed I could now daisy chain my samsung monitor into the Thunderbolt port in the back of the monitor. This isn't working.
Is this expected behaviour? Some people have said online that it will work if there's some other Thunderbolt peripheral between the Thunbolt Display and the VGA adapter, but I don't know what kind of peripheral they mean.
Apple support says that my model Macbook air can power two external displays.
How can I get this to work?
Thank you

I want to know if I can connect a vga monitor to the quad by simply getting a vga to dvi adaptor.
Yes, you can.
(50389)

How do I get my new 27" Thunderbolt Display to work with my mid-2010 Macbook Pro?

How do I get my new 27" Thunderbolt Display to work with my mid-2010 Macbook Pro? Or am I SOL?
Hardware Overview:
Model Name:    MacBook Pro
Model Identifier:    MacBookPro6,1
Processor Name:    Intel Core i7
Processor Speed:    2.8 GHz
Number of Processors:    1
Total Number of Cores:    2
L2 Cache (per Core):    256 KB
L3 Cache:    4 MB
Memory:    8 GB
Processor Interconnect Speed:    4.8 GT/s
Boot ROM Version:    MBP61.0057.B0F
SMC Version (system):    1.57f18

You can't. Theoretically, Thunderbolt devices that only transfer video and audio should work with Mini DisplayPort MacBooks like yours, but it's not the case of the Thunderbolt Display. Its firmware doesn't allow it to be used with non-Thunderbolt Macs, so you can't use the Thunderbolt Display with the Mid 2010 MacBook Pro.
Instead, you have to look for another screen, or you can get an adapter and connect the MacBook Pro to a TV

Hi - How do I connect an HDTV as a second monitor to Thunderbolt display with macbook pro in clamshell mode?

I have a Late 2011 Macbook Pro in clamshell mode connected to a Thunderbolt Display with the built in Thunderbolt cable. I want to then connect an HDTV via the Thunderbolt port at the back of the Thunderbolt display. I already had a cable that I thought would work which turns out to be a MiniDisplay port to HDMI cable and therefore not compatible with Thunderbolt to Thunderbolt (Mini DisplayPort not being the same technology although it uses the same port - although I'm not an expert !!) So far a web search has provided me with the only solution being using a Thunderbolt dock or storage that has multiple Thunderbolt ports and then using that to daisychain inbetween the Thunderbolt Diplay and the HDTV. The cheapest solution I can find for this would be about £250. Surely not ??!!!!
Many thanks for any comments - Nik

You could also use aThunderbolt dock with HDMI, such as:
<http://www.belkin.com/uk/F4U055-Belkin/p/P-F4U055/>
<http://www.caldigit.com/thunderboltstation/>
<http://www.elgato.com/en/thunderbolt/thunderbolt-dock>

Thunderbolt Display with mini-displayport Sapphire HD 7550 video card

I have a Mac Pro 5,1, Model A1289, made in June 2012. It came with a Nvidia Quadro 400 graphics card, but I want to purchase a Sapphire HD 7550 3GB Mac Edition graphics card in order to use a 27 inch Thunderbolt Display. I know the Sapphire 7550 card will work in the Mac Pro version I have.
The description of the Sapphire 7550 card says it has two mini-display ports. Will the 27 inch Thunderbolt Display work with this card?
I have read information on various forums that suggest it will work and others that say it will not.
Will a Thunderbolt Display work with a video card that has mini-display ports or does it have to specifically say it is a Thunderbolt port?
Does anyone have a clear answer?

see this post - you will not be able to run a tb monitor on the older silver tower mac pro's
https://discussions.apple.com/thread/6210828?tstart=0
you need the other 27 display - led cinema

Connect a Thunderbolt Display to a mid2009 MacBook Pro with mini Displayport?

Hello Fellars,
Is it possible to connect a Thunderbolt Display to a mid2009 MacBook Pro with mini Displayport?
Best regards,

That means i can either buy a new Macbook WITH Thunderbolt AND a Thunderbolt Display or
use my 2009 Macbook Pro with Displayport and an older Display??

Thunderbolt display crack

Similar Messages

Maybe you are looking for