Thunderbolt Display "dead" after firmware upgrade to Version 1.2

Hi,
I just run the Thunderbolt F/W update to 1.2 as offered by the AppStore Update. I have a 2014 MacPro with 2 Displays connected. In good faith I just confirmed to apply the update without much reading the fine print. The F/W update brought the system to a complete standstill. After 2 hours of waiting in the boot screen, I rebooted the system manually (5 secs power button). One of the Thunderbolt displays first just flickered, then decided to completely die. The System report says: unknown device in the Thunderbolt section. The 2nd display hasn't been updated during this procedure.
How can the F/W of the 'dead' display be re-installed? I also tried to connect it to a MacBook pro. Same result. The display is entirely black.
Any help or suggestion is much appreciated. Thanks!

Put me on the list as well.
I've had this TB display for two years and have had no issue with it. Clicked OK on the firmware prompt and now I have a $1000 paperweight/laptop charger.
What I have tried:
Reset SMC and NVRAM on my MBP.
Unplugged the display from power and all peripherals and let it sit for ~24 hours before trying again.
Downloaded the firmware installer from Thunderbolt Display Firmware Update v1.2. It tells me that no thunderbolt display is connected.
So far nothing has produced a result.
System report shows an unknown device on the TB port.
A used logic board for the display is around USD$220 on ebay.
I really wish I had not attempted to install the firmware now.

Similar Messages

IMac won't start with Thunderbolt Display connected after firmware update

After updating my thunderbolt display firmware to version 1.2 this morning via the App Store, my mid-2014 iMac won't start up with the external display connected. I can get the iMac to start up only by disconnecting the display's thunderbolt connector. After the iMac comes up, I can reconnect the display and everything appears to function normally. I've tried several restarts and the iMac won't start up with the display connected. Anyone else experience this?

Hello rameta,
It may help to reset your Mac's SMC and PRAM.
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/HT3964
Reset your computer’s PRAM
http://support.apple.com/kb/HT1379
Cheers,
Allen

SunRay 2FS DTUs dead after Firmware upgrade?

Hi everyone,
although I am fairly experienced in Solaris this whole Thin Client business is a bit of unchartered territory to me as of yet... following situation:
I got 2 SunRay 2FS DTUs and I have a vanilla PC setup with Solaris 10 U6 for x86. Installation was smooth except for the onboard NICs - I had to locate and manually install the appropriate drivers (skge). Installed SRSS 4.1, no problems, made a basic configuration (skge0: standard LAN, skge1: SunRay LAN with the standard 192.168.128.0/24 network). Installation told me DTUs would be firmware-upgraded after next power-cycle. Fired up the first DTU, it displayed the firmware upgrade OSDs and power-cycled - so far so good. But after the power cycle nothing happened - LED on the front is green so obviously POST is okay but the OSD constantly display status "1" (waiting for ethernet link to come up) and nothing else happens. Link lights on the NIC are on, when I send packets on the skge1 network (pings) they even flash, so I assume it's not the cables. Strangest things of all: I tried DTU 2 and the exact same sequence happened - so I am sitting here with 2 dead DTUs - any chance of reviving them? I scoured the 'net for information but I got no description that was even close to my problem...
Kind regards from Germany,
Henning

after installing sun ray server remember to:
1) utadm
2) utconfig
http://docs.sun.com/source/819-2383/config.html#59570 <- old but right

HP8600 Plus won't send or receive fax after firmware upgrade

Hi All,
Suddenly my HP8600, refuses to send or receive fax. I get the message "Can'r send or receive fax" immediatley after power up. I have a strong feeling that the problem started after an automatic firmware upgrade to version OJP8600_N911a_R1435A . Unfortunately there does not seem to be a simple way to downgrade or is there? HP refuses to tell. I have checked the telphone line and the connection also tested with another fax machine. I tried resetting several times without any success. It is just out of warranty and works perfectly in all other respects.
Do someone have any ideas?
Thanks in advance.
Bondra12

Hello @Bondra12 , welcome to the forums
I understand you now cannot send or receive a fax, and I am here to share my suggestions with you.
No, you cannot reverse a firmware upgrade from my knowledge. I would suggest however, troubleshooting the fax problem by trying out the steps from this guide: Cannot Send or Receive Faxes
If the problem does happen to continue, and I wish that it doesn't, to give us a call to see if you have any out of warranty printer options.
Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
Best wishes,
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

T410i SSD user and master password problem after firmware upgrade

Hello.
I have problem with my Corsair Force 3 120GB SSD. After firmware upgrade of SSD my master and user HDD passwords are no longer valid. I'm stuck on BIOS screen and cannot unlock my SSD. After firmware upgrade procedure i got BSOD. Same happened during firmware upgrade on my previous SSD (INTEL X25-M 80GB) but after restart everything was OK. Please help!
Previous firmware version: 1.3
Current firmware version: 1.3.3
SSD connected to another computer shows RAW partition data, but firmware version is 1.3.3 - seems like update was successful.

My X301 Intel x18 got bricked also after a BIOS update then secure erase (was going to sell it). I plugged it to a USB kit and onto a desktop and it was recognised and able to format. But plugging it back to the lenovo it is still a brick. My lucky star there was warranty it was replaced by lenovo.
You may want to try it and extract the data, if it works. And hopefully you can still format it and made it work pluggin back to the lenovo.

PC-Suite sync fails after Firmware upgrade of E65

After firmware upgrade of E65 PC-Suite stops syncing Calendar & Contacts from outlook. No error messages, just "0 entries has been updated".
- PC-Suite updated to 7.0.9.2
- Outlook 2003
- XP Prof.
Any ideas?
Solved!
Go to Solution.

The funny thing is - the notes are synced???? If I restore some old contacts they'll double up in outlook, so I think the problem is, that the sync app doesn't see the outlook contact & calendar folder.
Does somebody has an idea?

Hello! Help me please, I have a problem with the program occurred after the upgrade to version 3. 6. 16, namely by pressing the button 'Open a new tab' nothing happens. ?

Hello! Help me please, I have a problem with the program occurred after the upgrade to version 3. 6. 16, namely by pressing the button 'Open a new tab' nothing happens. ?

This issue can be caused by the Ask<i></i>.com toolbar (Tools > Add-ons > Extensions)
See:
* [[Troubleshooting extensions and themes]]

Facetime disappered after i upgraded ios version in my iphone 5c how can i get it back

facetime disappered after i upgraded ios version in my iphone 5c how can i get it back
model ME499AE/A

I would start by checking setting general restrictions to see if its restricted.
8if it's not, then it's hiding somewhere on your phone. Swipe down to search the iPhone from the home screen and see where it's at.

Crippled 192.168.1.1 page after firmware upgrade

hi,
i recently upgraded the firmware of my WRT160N V2 to 2.0.03.
but since then when i login i get a crippled page on 192.168.1.1 with not even a menu. so i cant even downgrade. is there something i can do?

It is good to know that the issue is resolved
After firmware upgrade it is always recommended to reset and reconfigure the router and I think that is why you were unable to see the menu on the setup page of your router.

No contacs after firmware upgrade on N70

Hi
I did a firmware upgrade yesterday on my N70 using NSU. Of course I did a backup using the uptodate Nokia PC suite. After the firmware upgrade I saved the data back to the phone aagin using the Nokia PC suite. Everything looks good except that no contacts are there.
I did the upgrade again just to make sure that everything went OK with the same result.
Can some help or has the same problem?
Firmware V 5.0638.3.0.1 18-09-06 RM-84
PC Windows XP SP2
Nokia PC Suite 6.82.22.0
NSU 1.2.0en
Best regards
Chris

not sure about your PC Suite version but this has been well documented in these forums and I had the same problem and with N70. I think it was mentioned as a PC Suite issue, or a combined PC Suite issue N70 issue with many people reporting it. Anyway nothing you can do but enter your contacts or transfer from another phone

HP Laserjet p1102w - after firmware upgrade / Smart Install update - down to 1MB free memory

Hello,
I have a Laserjet p1102w running off a laptop with Windows 7 64-bit. Just bought the printer this month.
After updating the firmware to 20120814 version and updating the SmartInstall update utility for the 20120814 version as well, I am now down to 1 MB free memory (out of 8MB originally). [Another LJ p1102w updated prior to these updates has 3MB free memory.]
Because I have 1MB free memory, the printer is almost a brick. It can print simple text based pages - however, printing any page with a graphic or a PDF file will cause the printer to take forever to receive data - essentially preventing printing a page on my new printer (while printing the same page instantaneously on my older nonupdated p1102w).
Is there any way to fix this problem, given there is no memory upgrade option? Otherwise, this printer is a brick.
Thank you in advance for a reply - especially from HP.

Hi cyskim,
Did you tried turning the printer off and on after updating the firmware? This should clear its memory, including any memory may affected during the firmware upgrade proccess .
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Iomega Storcenter ix4-300d stuck at 95% after firmware upgrade

Hi,
I upgraded my device after I got an email that there is a new firmware:
An update to version 3.2.10.30101 of the Iomega StorCenter ix4-200d software is now available
I installed the update but now it is stuck at 95% after rebooting.
Never had any problem before the firmware upgrade.
Any advice?

Hello BelgianTomas
I recommend that you first power down the unit if the unit has not completed the boot process. Then re-seat all disks and try booting the unit again. Please do not try to access the web interface until the power led is solid white.
Next would be to try moving the internal disks to different bays to see if a different drive order wil allow the unit to boot.
If that does not help, LenovoEMC suppor should be contacted for more advanced options.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Toshiba 47M7463DG no Cloud service after firmware upgrade

Hi All,
I have a problem with my Toshiba 47L7463DG. The Cloud services (accessible from the Home button) stopped working after the recent firmware upgrade. Is there something I can do to roll back to the previous firmware version or fix this problem?
Details:
Toshiba 2014-051
May 21 2015
Software Version 8.1.97.09.01.1
MBoot Version 00813201
Shipout G
Thanks in advance.
hysten

Hello,
I have the same problem.
I have above mentioned TV since 3 months So far, everything was wonderful.
Yesterday an update is installed automatically.
After that all stations were adjusted and I no longer get into the cloud menu.
So if I press the button with the "house", nothing happens.
Wi-Fi is enabled and network test was successful. The Red button also works. So I'll be over in the individual libraries.
Three times I set back the TV .Without Success.
Once I was able to get into the cloud menu. When I went out of it and want into the menu again nothing happened.
I also can not access the contents of my USB flash drive.
The latest firmware is installed.
Did someone have an idea?
Thanks in advance
Jan

E66 GPS problem after firmware upgrade to v.500

hi there, sorry but im going crazy with this problem....
id like to know who has a nokia e66, performed the v.500 upgrade and has GPS that doesn't work anymore after doing the upgrade, am i the only one?? what did the new upgrade changed? how to fix this??? i did all i could think of.. format memory card, reset phone, reinstall firmware etc etc. before upgrade it was working like a charm, getting signal fast and all. tried to enable and disable a-positioning, etc etc, resetted, removed battery etc etc.... and i upgraded the firmware with Nokia Ovi Suite for the note.. so the "good" stuff.
gabrio

famous007 wrote:
Hi I am also having the same problem. I upgraded my firmware to version 500.21.009 and my gps is not working. Anyone has a solution to this problem. Will the latest firmware upgrade resolve this issue?
@famous007
Presumably you have this version of Ovi Maps installed upon your E66:http://europe.nokia.com/support/product-support/maps-support/compatibility-and-download#/nokia-e66/
If you go to Menu > Tools > Settings > General > Positioning > Positioning methods - try temporarily disabling all except Integrated GPS, go outside away from tall buildings if feasible launch Ovi Maps and wait 20 - 30 minutes for first positional fix to be established.
Happy to have helped forum with a Support Ratio = 42.5

T1000 wont boot after firmware upgrade if SCA6000 is connected

Hi guys,
as u may have guessed from the topic, I had a T1000 server with a sun SCA6000 crypto card mounted in the PCI slot. All worked fine until i tryed to upgrade the firmware on the server to the last available release (6.7.8 with patch 139435-06 ) . After the upgrade procedure, the system did not boot anymore. This is the console output with POST after the poweron command:
sc> poweron -c
Enter #. to return to ALOM.
0:0:0>
0:0:0>Sun Fire[TM] T1000 POST 4.30.4.a 2010/01/06 15:23
       /export/delivery/delivery/4.30/4.30.4.a/post4.30.4-micro/Niagara/erie/integrated (root)
0:0:0>Copyright 2010 Sun Microsystems, Inc. All rights reserved
0:0:0>VBSC cmp0 arg is: 0fff0fff.00000211
0:0:0>POST enabling threads: 00000000.0fff0fff
0:0:0>VBSC cntl arg is: 0fff0fff.00000211
0:0:0>VBSC selecting POST MAX Testing.
0:0:0>VBSC setting verbosity level 2
0:0:0>Start Selftest.....
0:0:0>Master CPU Tests Basic....Done
0:0:0>Init MMU.....
0:0:0>L2 Tests....Done
0:0:0>Test Memory....Done
0:0:0>Setup POST Mailbox ....Done
0:0:0>Extended CPU Tests....Done
0:0:0>Scrub Memory....Done
0:0:0>Functional CPU Tests....Done
0:0:0>Extended Memory Tests....Done
0:0:0>IO-Bridge Tests....Done
2010-06-17 17:45:02.383 0:0:0>INFO:
2010-06-17 17:45:02.399 0:0:0>     POST Passed all devices.
2010-06-17 17:45:02.433 0:0:0>POST:     Return to VBSC.
2010-06-17 17:45:02.449 0:0:0>Master set ACK for vbsc runpost command and spin...
SC Alert: Host system has shut down.
SC Alert: Host System has Reset
JUN 17 17:45:22 ERROR: HV Abort: <Unknown?> (217f14) - PowerDown
SC Alert: Host system has shut down.
sc> Guessing an hardware compatibility problem, i tried to remove the SCA6000 board and the system booted again without an hassle.
Unluckily, I need the SCA6000, and I don't have any other server in which to mount it, so I tried to downgrade the firmware to the release I had before the upgrade:
firmware version: 6.6.7
patchid: 136928-05
but the system does not boot anymore with the SCA6000 connected. I even tried an older fw release just to be sure (fw 6.6.1, patch 136928-01), with the same result.
I did not find mention of any incompatibility in T1000 or SCA6000 documentation.
Any help would be REALLY appreciated
Many thanks in advance.

Hi,
This looks similar to the bug 6630313 :: http://sunsolve.sun.com/search/document.do?assetkey=1-1-6630313-1
As described in the bug document, it is due to lower f/w rev. on the SCA6000 and solution is to upgrade the crypto card f/w to 1.1.0 /1.1.0 (bootstrap/operational )or later.
Another workaround would be to install system f/w 6.2.4 or 6.2.8 which works well with crypto card f/w 1.0.4/1.0.7.
Copying relevant part of the document for ref.
=======================
Work Around: The card is recognized by obp and prtdiag with firmware 6.2.4, so at this point customer is using firmware 6.2.4 as workaround.
Customer's crypto card is currently running 1.0.4/1.0.7 bootstrap/operational firmware. Customer can upgrade the card to newer firmware such as 1.1.0/1.1.0 by moving card to a system that boots successfully such as Ontario T2000. After such upgrade, install the card back into T1000 which should boot successfully with sysfw 6.4.0, 6.5.5 or 6.5.11 posted on Sunsolve.
Another workaround is customer can downgrade the T1000 sysfw to 6.2.8 so they can boot with the crypto card. After the T1000 is up and running with sysfw 6.2.8, customer can upgrade the crypto card fw to the latest 1.0 patch on the T1000 itself, then upgrade the T1000 sysfw to the latest
version posted on Sunsolve. This workaround does require customer to have access to an Ontario T2000 system.
Another workaround is customer can downgrade the T1000 sysfw to 6.2.8 so they can boot with the crypto card. After the T1000 is up and running with sysfw 6.2.8, customer can upgrade the crypto card fw to the latest 1.0 patch on the T1000 itself, then upgrade the T1000 sysfw to the latest
version posted on Sunsolve. This workaround does not require customer to have access to an Ontario T2000 system.
========================
HTH
-Mehul

Thunderbolt Display "dead" after firmware upgrade to Version 1.2

Similar Messages

Maybe you are looking for