Thunderbolt Hard Drive Not Recognized

I've got a brand new Seagate Backup Plus 1tb hard drive and when I plug it in to the Thunderbolt input on my Mid 2010 Macbook Pro running Lion, it's not recognized in Finder. I looked in Disk Utility and it's not there. I looked in About this Mac and the Thunderbolt option under the Hardware section says that nothing is connected to the port. Could someone please help me out here? Does having a Thunderbolt port actually mean that it workds? I'm being a bit naive here. Thanks for your kind help.

2010 Macbook Pros don't have Thunderbolt. They have a visibly-identical mini-Displayport connector, but that's just for displays. If you look at the small icon next to the port, a Displayport icon is square, a Thunderbolt icon is a lightning flash.
Matt

Similar Messages

Hard drive not recognized during windows server 2008 setup

hard drive not recognized during windows server 2008 setup

Hi,
Whether the hard disk is recognized in BIOS?
Connect it to another computer to see if it could be recognzied incase the cause is the disk itself. Also please check if it is really a RAID instead of a single hard disk - a single disk should be recognized directly while RAID cannot be recognized until
a suitable driver is installed.
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Advanced Format Hard Drive not recognized by HP DV6000 Controller

Hello,
I have an HP DV 6000 laptop (6276 I think, I'm at work can't check) that came preinstalled with a Western Digital 160gb 1.5gb/s 5400 RPM drive (Vista) that failed a couple of weeks ago. So i bought a Western Digital 750 GB WD Black SATA III 7200 RPM 16 MB drive to replace it. I read about people having some problems with Advanced Drive Format hard drives not being recognized by their controller, but also read that depending on the controller and specific Dv6000 model laptop they had-one wouldn't run into problems.
Well sure enough, when attempting to install Windows 7 I received the error that the hard drive was not detected. After researching online I came across an article on WD's site that noted
"Our SATA II hard drives use autospeed negotiation. This enables our SATA II drives to automatically detect the motherboard data transfer rate, making it backward compatible with SATA I data transfer rates. However, some older SATA I controllers are unable to support autospeed negotiation and cannot recognize the drive. This “drive not detected” condition occurs when a chipset is incapable of correctly negotiating the data transfer speed with a SATA II hard drive."
my drive is a SATA ||| but I'm pretty sure it's the same problem. The site goes on to say a fix would be to "purchase and install a third party PCI or PCI-Express Second Generation Serial ATA controller card for your Serial ATA hard drive(s)."
My question(s) are.
1)Is the problem that I am trying to install a Sata ||| hard drive on a laptop with a controller that will only recognize SATA | hard drive?
2) Or is the problem that the hard drive is an Advanced Drive Formatted hard drive and I need to buy a hard drive with out that specification?
3) Or Should I buy a SATA controller card as WD suggests on their website and if so will this definitely allow my laptop's controller to recognize the new hard drive and proceed with the installation?
4)Or Should I just return the hard drive and buy a SATA | non Advanced Drive Format hard drive? (question 2 basically)
Thanks for your help!

Hi @jasmine00
Welcome to the HP Support Forums.
I certainly understand your issue with the drive upgrade. Unfortunately it is a bit of the nature of notebooks, the sacrifice of a large amount of upgradeability, in exchange for compactness and portability. Whenever a new technology comes out, older notebooks are never really going to be easy to upgrade, it at all. Normally the unit as a whole is tested with a set list of hardware, and only those items are supported.
That being said there is this document that could be helpful with your problem.
Preparing Advanced Format hard drives for Microsoft Windows installations on HP Business Notebook PC...
And for your reference:
HP Pavilion dv6000 Notebook PC Maintenance and Service Guide
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Thunderbolt partitioned and formatted hard drive not recognized on USB2/3

I have a MBA (mid 2012) and recently purchased a Seagate Desktop Thunderbolt Adapter (STAE129), a Seagate Backup Plus 4TB USB 3.0 external drive (STCA4000100), and Apple Thunderbolt cable. The 4TB hard drive can be separated from the USB 3.0 adapter and the drive placed on the Thunderbolt adapter. I created two partitions (3TB and 1 TB) on the 4TB drive while it was mounted on the Thunderbolt adapter and formatted them Mac OS Extended (Journaled) using partition map scheme GPT. Everything works as expected, the drive hits r/w speeds in the 180 MB/s range (using Blackmagic Disk Speed Test), and no issues at all transferring data to the 3TB partition and using the 1TB partition for TimeMachine.
However, if I disconnect the hard drive from the Thunderbolt adapter and place it on the USB 3.0 adapter and connect it to my MBA, Mountain Lion says "The disk you inserted was not readable by this computer and gives me the options to Initialize, Ignore, or Eject. Going into Disk Utility app, the drive shows up without the partitions I created when the same drive was mounted to the Thunderbolt adapter (just shows disk1s1). In fact, the drive label (Disk Description) is different too and the Partition Map Scheme now shows MBR!
To try work-arounds, I went ahead and repeated the partitioning and formatting steps with the drive attached via USB 3.0 and all works fine until I put the drive back on the Thunderbolt adapter where once again OSX reports that the disk is not readable. I've even tried a single partition with no luck. In short, the drive partitioned and formatted on Thunderbolt is unrecognized under USB and vice versa.
Shouldn't the disk preparation and data be consistent across these different interfaces? I would think so. My biggest concern is that if I had a failure in the Thunderbolt setup (assuming the drive itself does not fail), then I can't access my data. This is not a very comfortable situation.
I'm assuming I've overlooked a very basic detail. Appreciate any steer to solve this problem.
Thanks,
Rob

Thanks for that, I recently ran into the same problem. I even chatted with Seagate tech support and they didn't know the answer.
My situation is a bit different from you. I bought the 3 TB Thunderbolt version of the drive directly and then purchased a USB 3 adaptor seperately. You see, I still own a 3 year old Macbook Pro that doesn't come with a Thunderbolt port. I was looking to upgade to a MacBook Air later. I thought that I might as well buy the TB version now.
In anycase, my old MacBook Pro won't see the drive when I use the USB3 adaptor. I get the same exact error message as you did. I can't really test it on Thunderbolt since I don't have one. I'm going to go install the Thunderbolt drivers now and hopefully, it will recognize the drive afterwards. I'll let you know what happens.
BTW, I was thinking of reformatting the drive with NTFS so that I can use the drive on PCs. My mac has the NTFS drivers loaded so it's no problem. I hope this won't screw up the Thunderbolt connection later when I do get the Macbook Air?

Thunderbolt powered hard drive not recognized !!!

Hey i have a macbook pro ( early 2011 ) and i recently bought this new hard drive from BUFFALO inc. ( BUFFALO MiniStation 1 TB Thunderbolt / USB 3.0 Portable Hard Drive with Thunderbolt Cable - HD-PA1.0TU3)
My hard drive isnt getting detected via thunderbolt cables. The LED keeps blinking but the hardrive isnt shown . It works perfectly when connected through USB . I tried updating my software and firmware but it is already up to date. Someone please help me.

When you plug in your TB Device, and open Disk Utility, does it see your TB drive in the sidebar?

Memory modules and hard drive not recognized

I removed and reinserted the factory installed Satellite L505D-LS5007 laptop hard drive and memory modules just as practice for installing a hard drive upgrade and an 8GB memory upgrade. The problem is obviously with the memory and not with the hard drive.
After the first practice try, one memory module was recognized. Also for a few seconds after the first practice try, I ran the PC with the battery installed, but no memory installed. I did not look in the User's Guide first to see that I should have removed the battery before removing the memory.
Now the System Indicator Lights for the HDD Activity and Memory Card Reader do not light up. The PC turns on and the display is solid black with no messages.
Before buying new memory modules, what possible ways might there be to get the PC to recognize the factory installed memory modules and hard drive again?
Solved!
Go to Solution.

When troubleshooting, I always change one variable at a time. I would hate to miss a solution by being in a hurry. In this case, you may have damaged either the RAM or the RAM slot. I would stick with the Toshiba specifications for the RAM, making sure it is the correct size, speed and type recommended. I also recommend that when you replace the RAM that both modules be from the same manufacturer, size, and specification. Try one RAM module in one slot and then the other. And then try both RAM modules in both slots. After the testing you should be able to figure if this is a RAM problem or a RAM slot problem.
In the case of hard drives, the real test is whether or not the Bios sees the hard drive. If the Bios doesn't see the hard drive, it's not going to work. The Bios should see the hard drive whether or not the hard drive is partitioned, formatted or has data on it. My experience has been that many Toshiba laptops will work fine with larger capacity hard drives provided they are the same speed in RPMs, have the same interfacing connection and physically the same size.
Again, prior to doing any work on your computer, make sure that both the AC power has been disconnected and the battery has been removed. Be careful out there. A blown repair job by a non-Toshiba tech is NOT covered under warranty.

Yoga 2 Pro Hard Drive not recognized

I got my Yoga 2 Pro as a Christmas present and have had issues with the computer recognizing the hard drive every time it boots up or enters sleep mode (and this is after the 1 initial boot up where I didn't have to enter the BIOS). Not sure if this is a bios or hardware issue, but I can get it booted after entering the BIOS, changing various (seemingly random) settings (UFEI/Legacy support usually) to get the computer to even recognize that it has a hard drive installed at all. Once it does boot, as long as it doesnt sleep or shut down, it'll continue to work, leading me to think this is some sort of BIOS issue. Has anyone been able to resolve this issue without the hassle of returning it to Lenovo an getting a whole new one? The computer is great, when it boots up, but this is extremely disappointing/frustrating to have to enter the BIOS every single time I want to turn the computer on to use it!

@Lenovo Support - Please respond to this issue.
SO MANY PEOPLE HAVE FACED THIS ISSUE & ARE STILL FACING - BUT NO RESPONSE FROM LENOVO SUPPORT...... !!!!

New WD Scorpio Black 750GB hard drive not recognized

Hey guys,
I've purchased a WD Scorpio Black 750GB hard drive for my newly acquired MacBook Pro 5.5, 2.26 GHz Intel Core 2 Duo. The hard drive is installed (internal) but not being recognized by disk utility. Browsing on Google, I've found this to be a common occurring problem but as there were no direct solutions, I'm posting this in case anyone has any solutions to this issue.
I've reset the PRAM/ NVRAM with no avail. Any assistance would be greatly appreciated.
Cheers

Your response is not 100% clear to me.
Have you actually installed the WD and Seagate HDDs in the MBP or just connected them while in an external enclosure?
When you put the original HHD back in the MBP, it is recognized in Disk Utility but cannot be repaired? Is that the case.
Have you tried to put in the original Installation disk and has the original HHD been recognized and/or one of the other HDDs in an enclosure been recognized?
Ciao.

Lacie 250GB External Hard Drive NOT RECOGNIZED

HELP! My Lacie External HD that I've had for several years and holds a lot of my files is no longer being recognized on my MacBOok Pro. It used to recognize it instantly when I plugged the USB cable to the USB Port - now, nothing. The Lacie light is on, but my laptop isn't reading it at all. What's going on??? I did a disk utility - it's not showing up there at all either. Is it due to a software update? Don't get me started on losing out on using my entire Dreamweaver/Flash Studio MX 2004...
ALSO, I notice my iPhone is not being recognized in iPhoto anymore either. It is recognized in iTunes. And yes i've heard many folks say email photos should be removed, which i have done so and still nothing!
HELP PLEASE!!!

Are other USB devices working normally, Eric?
If so, the most likely cause is that either the bridge or the drive itself in your external enclosure has failed (assuming you have tried a different cable)
No, it is most unlikely to be due to a software update. With an old external drive like yours the most likely explanation is that it has simply failed. If it is the bridge, rather than the hard drive itself, that has died you may be able to remove the HD from the LaCie enclosure, put it in a different enclosure, and recover your stuff. In some cases, too, a drive light will illuminate when the drive is connected to the computer, even if the power supply to the drive itself is faulty. You might want to contact LaCie to see if they have any advice to offer about such situations.
Have you tried the drive on another Mac or another drive on this Mac? THis would immediately narrow down the location of the problem, of course.
Cheers
Rod
Message was edited by: Rod Hagen

MBP Late-2011 hard drive not recognized

Okay, so last November 2012, not even a year after I bought my MBP, it just froze and wouldn't respond to anything. All it showed was the rainbow loading circle and the computer crashed. I brought it to the Apple store and the person behind the Genius bar said that it was a hard drive problem and he replaced it. However, ever since then, I noticed that my mac has been running very slow and programs would take a lot longer to load.
5 months later, my computer is having problems again and one time when I turned it on, it just showed a blinking folder with a question mark. I know this means it can't find the system software. I brought it to a friend and he tried to fix it first by using the OS X system software disc but that didn't work. Then he thought the problem was the hard drive cable so I bought a new one and when he replaced it, my hard drive still isn't recognized. At this point he thinks it's something with the logic board or something since nothing seems to be working. Right now, all I'm doing is connecting my hard drive to the USB and using booting from there. Everything else is working fine. Does anyone have any suggestions as to what I can do? (btw, I don't have AppleCare)
Thanks.

The good news is that it is not the logic board, other wise the MBP would not function at all. The symptoms that you describe are a strong indication that the internal HDD connection is faulty.
As mentioned before, have the technicians at the genius bar look at it and if I am correct, they should be able to install a new cable and allow you to use the MBP with the HDD inside the MBP. This is not an expensive repair.
It is also possible that the replacement cable that was installed earlier was not done correctly.
Ciao.

Macbook Leopard Update- Hard drive not recognized?!?!

Question- What do you think caused this problem, and how can I best fix it?
(See below for information)
Well, I finally decided to update to Leopard. I put the disk in my Macbook, and everything went smoothly as it verified the installation DVD- until the end of the verification, that is. A message screen would pop up telling me the disk was dirty. "Okay," I thought,"No problem." I was a bit puzzled, though, because the installation with the same Family Pack disk went fine on my father's Mac. I cleaned the disk, and tried again. And again. Each time, I was greeted with the same message at the end of the verification. Frustrated, I took the disk and my laptop to Best Buy, hoping someone could help me there. We ran the installation again... to no surprise, the same problem occurs. This time, though, when we quit the installer and try to reboot, after the gray screen with the apple at the beginning, we are greeted with a black screen with one command line. NOT GOOD! We rebooted the computer again, this time starting up with a disk to check the permissions and hard drive. The diagnosis: The permissions on my Mac are screwed up, so it's not recognizing the hard drive. The Best Buy guy claims the permissions have been messed up since I bought the Mac, and everything will be just fine and dandy after I transfer the data to another computer, install the Tiger disk that my Macbook came with, update to Leopard, then transfer the data back to my Mac. I'm taking my Mac to the closest Apple store (about 2 hours away) for advice from the pros on Saturday. Until then, I'm hesitant to even turn the thing on, out of fear it will spontaneously erase the data or something to that extent.
Question: (in case you forgot)What do you think caused this problem, and how can I best fix it?

Unplugging worked!!!
I have no idea what PRAM is but someone said that unplugging your computer resets it so, I thought I'd give unplugging a shot. So, I shut down my computer and unplugged it. I also unplugged the power on the HD. (because I wasn't sure which one they were talking about.)
Anyway, I went away for about five minutes.
I came back plugged in the HD power first. Then, I plugged in the power cord for the computer and turned it on.
As soon as I logged in I was asked if I wanted to use my external HD for Time Machine backups.
I saw the icon for the HD on the Desktop where is belongs. I can open the drive and access the files with no problem.
Try this if you haven't yet.

IMac G5 Internal Hard Drive Not Recognized

I shut down my iMac G5 with the power button and not through the typical shutdown procedure once and then when it booted up it would not get past the gray screen. I eventually used the Leopard DVD to try to boot it and was able to get to disk utility to look at the drive. I tried to repair the drive but then the machine froze and I had to restart once more. Now the internal hard drive isn't recognized or seen at all. I actually switched out the SATA hard drive with another spare I had and that was not recognized either. I can get the mac to recognize the installation DVD still so I know my computer still functions properly but I just need it to recognize the drive now. Does anyone have any ideas how to resolve this?

Have you access to DiskWarrior or TechToolPro? Either of those might fix your problem otherwise, try booting from the Apple Hardware Test on your install disc and see what it says.

Hard crash now hard drive not recognized in disk utility.

During a virus scan the Macbook froze up now the computer does not seem to be accessing the hard drive. Tried to reinstall Leopard but the internal hard drive is not recognized (same is true when we tried to use Disk Utility). It will not start in safe mode either. Does this sound like a fried hard drive or maybe a corrupted drive that might be repairable with DiskWarrior? Any thoughts would be appreciated.

If the A/V you were using was Norton/Symantec, the drive may be OK. Norton is a virus.
Burn a Ununtu CD and see if you can boot into it and look at the drive before giving up on it.

Hard drive not recognized when connected to Apple keyboard

Hi there,
I'm using a dock (Henge) for my MacBook Pro with a wired Apple keyboard to which I connect a Passport hard drive using the USB port (my Time Machine backup). The hard drive is self powered but still it won't be recognized by the Macbook Pro. I have used the USB port to connect my iPhone without any issue.
Any ideas? Should I use a USB power booster?
Thanks
CB

The USB ports in the Apple keyboard are NOT powered, so your passport HD will not work on it because it pulls too much power from the USB port.
More info here: http://support.apple.com/kb/HT4049

Hard drive not recognized in HDD bay.

Randomly, my laptop gave me the spinny pinwheel of death when I opened it, and upon restart, I got the good old folder with a "?" indicating there was no OS. Naturally, I booted up in network recovery, and low and behold, my SSD was not in the Disk utility list. I made an adjustment some time ago where I removed my optical drive, and installed the old HDD that came with the computer in it's place. I switched the drives, so that the SSD was where the optical drive should be, and the HDD in the drive bay. Upon startup, the computer booted up as usual from the SSD, and the HDD was not recognized. So from there I conlcuded that both the SSD and HDD are working correctly without failure. After putting the drives back where they originally were (HHD in optical bay, and SSD in Drive bay), and I booted up holding the option key, The SSD and recovery drive were there, but I received a prohibited sign (circle with slash) after a minute. Now it is not recognizing the drive again. I'm not sure whats going on, anyone hav any input?
Thanks

You have a faulty hard drive to logic board cable. Replace that and you should be fine and the drive put in the main bay should show up.

Thunderbolt Hard Drive Not Recognized

Similar Messages

Maybe you are looking for