Thunderbolt port for ethernet adaptor and display

Hi-
As there is only one Thunderbolt port on a MacBook Air, how am I supposed to connect my gigabit adaptor AND a display at the same time?
Thanks.

Unless the display is (Apple's) Thunderbolt Display, which replicates TB as well as providing Ethernet, FireWire, USB, and audio, you might need to live with little less than "Gigabit" and get a USB->Ethernet adapter.

Similar Messages

Can the Gigabit Ethernet LAN Port be used with a Thunderbolt to Gigabit Ethernet adaptor and then to a Thunderbolt Hard Drive as a back up drive?

Can the Gigabit Ethernet LAN Port be used with a Thunderbolt to Gigabit Ethernet adaptor and then to a Thunderbolt Hard Drive as a back up drive?

If you use ethernet to connect the two AirPort Extremes together, you'll have Gigabit speeds available at all of the ethernet ports on both routers.
If you connect the second AirPort Extreme using wireless only and configure the Extreme to "extend a wireless network", then the maximum speeds that the second router can attain will be limited to the capability of the wireless connection. So, if you connect at normal "n" wireless speeds of say 130 Mbps, that will be the maximum speed available at the ethernet ports on the second AirPort Extreme.
I think you can easily see the difference between Gigabit ethernet, which is 1000 Mbps compared to "n" wireless at 130 Mbps. Even if you can manage to connect at 5 GHz speeds for wireless, the max speed will be in the 300 Mbps range, more than 3 times slower than Gigabit ethernet. Normal "n" speeds will be about 7 times slower than ethernet.
For streaming high definition video and other demanding sources, you'll need as much bandwidth (speed) as you can get. Ethernet is always the best choice if you can possibly use it. And...there's no wireless interference on an ethernet connection.
Message was edited by: Bob Timmons

Thunderbolt to Gigabit Ethernet Adaptor and iPad 4

Is there a way to connect the Thunderbolt to Gigabit Ethernet Adaptor to an iPad 4?

I've never seen any ethernet adapter for the iPad. I carry an Airport Express (any portable router would do, though) if I think I'm going to be in a situation where the only internet access is going to be wired. This happens frequently when I travel in Japan.

HT5299 can i connect my sony smart TV via thunderbolt port for better resolution.

can i connect my sony smart TV via thunderbolt port for better resolution.

You can connect the TV via the Thunderbolt port. However if the result is "better resolution" would depend on what resolution you have now (I'm guessing you mean with the HDMI adapter?)
I'm myself connecting the Mini Mac with a Thunderbolt->VGA adapter to my TV and get full 1920x1080 resolution.
Have you checked your Display settings? Make sure mirroring is off, then check what resolutions you can get on the current connection.
Please return with some more data.

One Thunderbolt port for two HDMI devices?

Hello
I was wondering, is there some sort of adapter that I can put in the thunderbolt port for my mac mini and connect two hdmi devices (monitors)?
HDMI 1
Mac Mini - 1 TB <
HDMI 2

Use the HDMI port for one monitor and a mini displayport to HDMI adopter on the other. That adopter plugs into the Thunderbolt port.
You want to set them up as extended displays.
he following also applies to Yosemite
http://support.apple.com/kb/HT5891
OS X: Using multiple displays in Mavericks

Create Separate Views for New,Edit and Display forms in Infopath

Hi,
I need to create a separate views for New, Edit and Display forms in infopath.
For ex : I need a Submit Button on Display form and not in New/Edit forms.
I tried, but i amnot able to get the changes.
Regards, Shreyas R S

I just validated my approach in a 2013 farm, this is precisely how it's done!
Step 1) List > Display Form
Step 2) Change the View within the Web Part Properties. In your screenshot it looks like you simply went to View Item on the single item, which is not the direction I gave =P.
**Assuming you've already created the multiple views within InfoPath, this allows you to set them up as distinct defaults for New, Edit and Display, let's make that clear. If you are not even to the point of having separate views, that is just in InfoPath,
Page Design tab, far left, New View button

Utilising Thunderbolt port for storage in a lab environment

Hi All
I'm looking to set up a lab and wanted to use Mac Mini's for their footprint and the 10Gbps Thunderbolt to share storage through something like Starwind NativeNAS. Has anybody got any experience of this or something similar? I know Mac OSX has the Thunderbolt
Bridge which can use the TB connection as an ethernet connection but i'm not sure if there's a way of doing the same from within Windows 2012? I've attached a diagram explaining what i'm looking to achieve.
Many thanks
Lee

Hi,
If your hardware doesn’t have the HCL, you may can’t get the official support, but maybe your hardware can used for the test environment, personal found there have some obvious
problems, such as it seems you choose the two 10GB connectivity for cluster, if both this is for storage connectivity or cluster out bond service, you need the third party network adapter as the heart beat connectivity.
More information:
Configuring Windows Failover Cluster Networks
http://blogs.technet.com/b/askcore/archive/2014/02/20/configuring-windows-failover-cluster-networks.aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

USB vs Firewire Ethernet adaptor and impact on network speeds

So my wife is going to be taking some online classes and wants to backup the wireless by connecting to our router via ethernet given that we've had some issues with our cordless phone interuppting our wireless signal. She's concerned about network speed since classes involve streaming video and being connected via webcam. I know Firewire is faster for transfering information in general...say to an external hard drive...does the same go for internet speed? Will internet speed be slowed should she opt for a USB ethernet adaptor versus Firewire?

The transfer speed will be governed by the slowest link in the chain. Fire wire theoretically is twice as fast as USB 2.
Ciao.

Determine port for ethernet card

I have been emailing with support trying to figure out why MAX cannot communicate with an ethernet card in my pc. I am new to ethernet and don't have the experience to solve this. I had explained that the MAX was giving error: " Insufficient location information or the device or resource is not present in the system." One solution suggested in the Ethernet tutorial was to run ping from the command line and see if it worked. I did that using the IP address of the ethernet card and it did work. I was then told by support to also use ping including the port number at the end for example 192.55.5.3:1. I do not know how to find port number. I did a web search and one solution was to run netstat from command line. I did that and go a long list of values and could not determine which was the ethernet card. Another thing I tried was in Wireshark under Conversations where the UDP: 2 tab selection showed port numbers for the card of both 138 and 139. When I tried using either of those port numbers with ping it gave me a error "Ping request could not find host 192.168.55.2:138. Please check the name and try again."
Can someone please tell me if there is another way to figure out the port for this ethernet card?
Thanks.

I don't understand. MAX will communicate to an instrument - not a nic. Is there something on an Ethernet port that you are trying to communicate to? If so, what is it? In order to use LabVIEW and VISA, you often have to manually add the instrument in MAX. Right click on Devices and Interfaces and Select>Create New>VISA TCP/IP Resource.

Firewall ports for Zone Sharing and Subscription?

Hi again!
What firewall ports need to be open for Zone Sharing and Subscription?...

Hello,
we updated from 11.3.1 to 11.3.2
Now i can not run the command chkconfig -a novell-proxydhcp to set the proxydhcp to autorun because i get...

SAP HANA Cloud Portal : Make Widget For Java Application and Display in HANA Portal

Hi Experts,
I have created one Java Application using eclipse luno.
I have successfully deploy on my hanatrial version and able to see the Started Application under the Java Application.
Can anyone have idea how to use this application in HANA portal and display/ run this Java Application in SAP HANA Cloud Portal Website.
I want to know is it possible or not ? and yes then how its possible ?
What are the steps require to make Widget for this java apps and publish on portal.
Many Thanks,
Mithun

Hi Mithun,
yes it's possible and relatively easy - follow Chapter 7 of the guide -
ESPM WebShop Extension
Regards
Kenny

Create URL for image content and display in new window

Hi,
I am attaching a new image and it is displayed in a table view.
I am having problems creating the URL for the image.
When i give the link of external site like http://www.google.com, it works fine. It does not work when i give as www.google.com.
It does not work for the image. Please help.
ls_properties-name         = 'KW_RELATIVE_URL'.
ls_properties-value        = lv_imgname.
APPEND ls_properties TO lt_properties.
ls_properties-name         = 'LANGUAGE'.
ls_properties-value        = sy-langu.
APPEND ls_properties TO lt_properties.
Assign file properties
ls_file_access_info-binary_flg = 'X'.
ls_file_access_info-file_name = lv_imgname.
ls_file_access_info-mimetype   = 'image/pjpeg'.
ls_file_access_info-property   = lv_string2.
APPEND ls_file_access_info TO lt_file_access_info.
Move content to file_content
lv_str = lv_img_content.
lv_strlen   = XSTRLEN( lv_str ).
lv_offset   = 1022.
lv_bytes_rd = 0.
lv_bytes_rm = lv_strlen.
ASSIGN lv_str TO <fs>.
WHILE lv_bytes_rd LT lv_strlen.
    IF lv_bytes_rm LT lv_offset.
      ls_content-line = <fs>+lv_bytes_rd(lv_bytes_rm).
    ELSE.
      ls_content-line = <fs>+lv_bytes_rd(lv_offset).
    ENDIF.
    APPEND ls_content TO lt_content.
    lv_bytes_rd = lv_bytes_rd + lv_offset.
    lv_bytes_rm = lv_strlen - lv_bytes_rd.
    CLEAR ls_content.
ENDWHILE.
Create a Document using class CL_CRM_DOCUMENTS
CALL METHOD cl_crm_documents=>create_with_table
    EXPORTING
      business_object     = ls_business_object
      properties          = lt_properties
      file_access_info    = lt_file_access_info
      file_content_binary = lt_content
      raw_mode            = 'X'
    IMPORTING
      loio                = ls_loio
      phio                = ls_phio
      error               = ls_error.
Using the logical and physical id's, get the file location as an URL
data:
lv_no type char1 value '1'.
    CALL METHOD cl_crm_documents=>get_with_url
      EXPORTING
        loio     = ls_loio
        phio     = ls_phio
        url_type = '2'
      IMPORTING
        error    = ls_error
        url      = lv_url1.
should i prefix the url with 'javascript:'?
Thanks in advance.
Regards
Shanthi

Hi Shanti,
The URLs that are external to the server, you should always have http://, your image URL is has http:// prefix? Other wise system will always look for the same inside the current BSP application. For Example your BSP application is ZBSP and if you are accessing www.google.com the URL in the browser will be
*******/bsp/ZBSP/www.google.com which will not be existing, hence causing the problem.
If not try adding http:// to the URL by concatenation and try.
Regards,
Ravi

Hello! I bought a minidisplay PORT to VGA adaptor and I had two problems.

Today before my presentation I had two problems with the adaptor: first one, part of the mac`s screen was cropped and the second one, after restarting my mac, the initial screen (with the apple logo) was also cropped. And it is still this way.
Could anyone help me ? I would be really appreciated.
Regards, Guilherme.
OBS: MacBook Pro Retina Mids 2012 15"

Hi guilhermefg120,
Welcome to the Support Communities!
The articles below may be able to help you with this issue.
Click on the links below to see more details and screenshots.
OS X Mountain Lion: About the Display pane of System Preferences
http://support.apple.com/kb/ht5369
Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
http://support.apple.com/kb/ht3382
Cheers,
Judy

Regenerating ports for Partner Profiles and Source System (RSA1)

Hello all you SAP gurus,
During a recent backcopy we have an issue after updating Logical System names using BDLS. This has updated the Partner Profiles (WE20) correctly.
BUT
These partner profiles are trying to use ports (WE21) that have been mistakenly deleted. But if we try to recreate the ports we get the message
-"Choose another name! Name range reserved!"-
This specific port is referenced in outbound parameters. Perhaps this is stopping the change?
We could create new ports and hook them up to the partner profiles, but I'm concerned that there might be other locations where the deleted ports are referenced.
Any help would be greatly appreciated!

Hi J,
You can try and disconnect and re-connect the BW System to R/3. That would force the recreation of the Partner Profile.
Take a look at the connection data in table RSBASIDOC, write down the parameters, especially the IDoc Type.
In SE37, run function RSAP_BIW_DISCONNECT_40 and specify parameters for BW System.
Then run RSAP_BIW_CONNECT_40 and specify those parameter again for the BW System.
This will recreate the Partner Profiles. Then check the assigned ports and see if you still have the same issue. Just make sure the RFC connection is set correctly and working in SM59 before doing all this.
In any case, you can create new ports in WE21 and allow the system to assign the numbers automatically and you won't have any issue.
Hope it helps.
Regards,
Luis
Edited by: Luis Sales on Mar 18, 2008 7:28 PM

MyBook Thunderbolt Duo for timemachine backup and external storage of photo library with Raid

Hi, I've recently updated my MacBook Pro to a new model and have therfore moved to a smaller SSD internal storage. I was thinking of buying the Thunderbolt Duo to use as a time machine backup and for working storage. What I was wondering was if I could patition the drive in such a way that I could keep a time machine backup of my mac (smaller partition) still protected by Raid (although not as important as will also have a copy on the internal drive) and use the remaining larger partition for my working photo, video and music partition (proteded by raid as this will not on my internal storage. Will this work? Sorry to ask a silly question but its a change to the way I'm used to working (large internal storage and exteral backup). Thanks for any help you can give. Chuck

Hello,
It should work.

Thunderbolt port for ethernet adaptor and display

Similar Messages

Maybe you are looking for