THX Setup Console Involuntary Configuration Cha

Presently I have a 5. speaker selection which works fine (sometimes). For some unexplained reason my default settings in THX Setup Console periodically change from 5. to 2., with the resultant cutoff of 3 speakers. At the same time, the location of my Front Center Channel Selection changes from my settiing of 'Above monitor' to 'Below monitor. My default changes remain in place for a variable time, ranging from several days to several weeks. I have installed the latest Audigy update (SBAX_WEBUP_LB_2_08_0004) with no effect. Win XP Pro, SP2.

It looks like you are not hitting r2 through the console, you are hitting r2 via telnet.
If this is true, you should be able to put a password on vty 0 4 and sucessfully connect.
"Password needed and none set" is a telnet error ... not someting that would come from a console connection.
In your host definitions on the TermServer, remember to use a loopback address of te TermServer (along with the port 2001, 2002 ...).
Like: host r2 192.168.1.1 2002 <--192.168.1.1 is the loopback address of the termserver (itself).
Good Luck
Scott

Similar Messages

  • THX setup console, no digital out

    I have Audigy 2 ZS notebook. I connected it to my home theater system via optical cable but I can not get 5. sound from all of my speakers. I can not select digital output on THX setup console. It is even not highlighted. Am I missing something? Looking forward to getting help.

    hey, i'm a newbie to all of this but i remembered that when i installed the sound card there were two sets of drivers, one for 5. surround sound and one for 2. stereo sound. you might not be able to select 5. surround because the wrong drivers are installed. try uninstalling it and reinstalling it with with 5. from the initial set up. maybe that will straighten it out. just thought that might help. but if it doesn't, well, i'm a newbie......

  • THX setup console is NOWHERE to be fou

    so far this question has been posted about 40 times and there has been no solutions for it so i'll ask it again,I?cannot find the THX console anywhere, it is on my setup disk but when i run it i get "setup has experienced an error" there is no download for it anywhere (accept for audigy) and i have tried about0 different things from various post to try and resolve this, including a full uninstall of all drivers and sofware (in safe mode) STILL no thx console, and i assume this is where the proper speaker config settings are as the creative drivers have none,So i have a sound card that is more expensi've than my motherboard but i get better 5. from my realtek on board sound!!?is there a way to fix this!!!theres not much point in 5. if you have no rear speakers,?it is getting old realy fast and so far the only fix iv found is to just not use the card, which isnt what id prefer to do with a brand new sound card.

    Thanks for the reply, those drivers look pretty cool, i'll give them a try later!!
    I managed to resolve the problem, its caused when you get the latest drivers and install them WITHOUT installing the ones from the disk, once youv put in the new ones you cant put in the old utilities, so for anyone else getting this problem. .uninstall all creative software (ALL)2.uninstall device in device manager.3.restart.4.install the drivers and utils?from your disk.5.restart, then install newer drivers.6.JOB DONE!?

  • THX Setup Console for Auzentech Cards (Home Theatre HD)

    I know that using DK's packs i can install the THX console and i 've used them for my older x-fi cards(really great packs for those older cards btw!). but installing his packs seems to alter other things even though all im installing is just the THX console. is there a way i can install just the THX console for my auzentech Home Theatre HD without one of DK's packs?

    Rootdown4594 wrote:
    I know that using DK's packs i can install the THX console and i 've used them for my older x-fi cards(really great packs for those older cards btw!). but installing his packs seems to alter other things even though all im installing is just the THX console. is there a way i can install just the THX console for my auzentech Home Theatre HD without one of DK's packs?
    Today is your luck day.
    Just sent this to a friend, so I've decided to make it publicly available.
    http://hotfile.com/dl/3546352/e568d/AuzenTHXConsole_3_50_05.exe.html
    There is no hardware check, so it will install on any system, but obviously will only support devices with a X-Fi PCI or PCI-E chipset.
    Finally, to make it clear, it supports Auzen X-Fi Prelude, Forte and HomeTheater HD cards.

  • Sound Blaster X-Fi Xtreme Music Bass level control in THX setup cons

    hi, i have a Sound Blaster X-Fi Xtreme Music, plugged in to a Logitech X-530 speaker system. The problem i'm having its in the bass redirection controls in THX setup console... The crossover frequency works fine, but i can't control the subwoofer level, i tried it a few days ago and it worked, it was the first and last time it worked... any help?

    Hello, I know this is un related but I require your help. Im on the same setup as you but I have the next speakers up the X 540. However the sound card seems to be louder on the left than the right. Is this something to do with the Crossover you mentioned?
    Thanks for you help.
    If you can help id be greatful if we could talk on msn?

  • Problems with the/while opening the THX Setup Cons

    hi everybody,
    hopefully i'm not asking an already often answered question, but since i didn't find a solution for my problem on the initial forum search i'll try my luck with a new thread.
    my first (little) problem is that whenever i open the thx setup console all volumes are set to the maximum. not that big of a deal, but still annoying. is there something i can do against this?
    the second (not that big either) problem is, that the calibration settings, to be exactly the db-settings, in the thx console aren't properly saved. sometimes (i didn't yet find out after doing what or when or why) they are just changed, and i have to set them for my setup again. any ideas?
    thx for your help in advance,
    -vio

    I had the same problem. Sometimes the settings just seemed to change, not sure why. I don't know of a fix and there is no save button.
    I just finished uninstalling everything Creative and then reinstalled the THX Console off the original disc only, then the new Audio Console, then the new Beta Drivers. Everything is working fine for now. There is also an update for the THX Console, but I haven't installed it yet.
    Good luck, hope this hel
    ps.
    Jason

  • "Windows Setup could not configure Windows to run on this computer's hardware" error using MDT

    Good day. I am using Microsoft Deployment Toolkit to deploy images to a group of ClearCube R3080D bladed PCs. Below are the server details:
    VMware virtual server with Server 2008 R2 Enterprise Service Pack 1
    Microsoft Deployment Workbench Version 6.1.2373.0
    Management Console 3.0 Version 6.1(Build 7601: Service Pack 1)
    Windows Deployment Services Version 6.1.7600.16385
    The image I am deploying to the blades is that of Windows 7 Enterprise x64 Service Pack 1 with Office 2010 and a few other third-party applications.
    I have pushed this image to literally hundreds of blades successfully. I had a problem with one blade and found that the HDD was faulty. I RMA’d that HDD and installed the replacement. I pushed the same image to the blade and it works fine to the very end
    then I receive the error ”Windows Setup could not configure Windows to run on this computer’s hardware.”
    I have checked the BIOS configurations on this blade and they are identical to those of several known good blades. In fact, I swapped HDDs between a known good blade and the blade in question. The problem seemed to follow the HDD. Therefore, I assumed that
    ClearCube sent a faulty HDD. I had the identical problems with a second HDD from ClearCube so I’m sure that the HDD is fine.
    I have read through http://support.microsoft.com/kb/2466753 
    as well as many other questions posed by other folks and I have yet to find a good solution.
    Again, this image works on all other blades that are of the same model and the HDDs are also of the same model. I'm quite confused!
    Tony

    Tony?
    What are you doing posting the same question 5 times, within 3 hours???
    http://social.technet.microsoft.com/Forums/en-US/67f72721-da1b-42bc-b373-9064fe1a8245/windows-setup-could-not-configure-windows-to-run-on-this-computers-hardware-error-using-mdt
    http://social.technet.microsoft.com/Forums/en-US/9e7ca626-5b67-4a3f-ade0-4bac767e060f/windows-setup-could-not-configure-windows-to-run-on-this-computers-hardware-error-using-mdt
    http://social.technet.microsoft.com/Forums/en-US/8c508acc-ad40-4608-911c-fbfbc5e293fe/windows-setup-could-not-configure-windows-to-run-on-this-computers-hardware-error-using-mdthttp://social.technet.microsoft.com/Forums/en-US/a8a98fce-0ddf-4a59-ba8a-9acab7de0c5e/windows-setup-could-not-configure-windows-to-run-on-this-computers-hardware-error-using-mdt
    If this post is helpful please click "Mark for answer", thanks! Kind regards

  • HT4519 how can i remove a mail setup through iphone configuration?

    I need to remove an exchange mail account that was setup via iphone configuration. Help.

    Settings>General>Profiles...tap on the Exchange Account, then remove.

  • Windows setup could not configure Windows to run on this computer's hardware.

    Just over a month ago, I purchased 6 identical Lenovo B5400 laptop computers for a small charity. Each is preconfigured with Windows 7 Professional, with a Win 7 recovery partition, and is supplied with a set of Windows 8 Pro recovery media (the charity
    requires Windows 7 installed). I unpacked three laptops, configuring the first one as required by the charity, and using the second and third to experiment with the sysprep / imagex process before applying it to the configured system for migration to the other
    laptops. After securing the second and third laptops by taking image backups, I applied sufficient configuration to the second to test the process, then sysprep'd it, and imagex'd it to a network drive, and to a USB stick. So far so good. After using imagex
    to apply the custom .wim file to the third laptop, I found it booted up through the "updating registry settings", "starting services", and "installing devices" phases, but when it got to "applying system settings", it
    displayed a messagebox titled "Install Windows", with the message "Windows Setup could not configure Windows to run on this computer's hardware".  In the last few days, I have explored all the other incidences of problems with similar
    symptoms found by a google search, including those on this forum, and tried numerous experiments without getting any further (in most cases not even getting as far)". The sysprep'd image on the second laptop boots ok, going through the same phases up
    to "applying system settings", then reboots normally, requests username and PC name, etc, the only defect being that it loses the Realtek display driver (which only takes 2 minutes to restore). I have tried imagex /apply to put the custom .wim file
    back on the same laptop it was taken off (the second laptop), and it works exactly the same as it did for the same system immediately after sysprep'ing. The only difference between laptops 2 and 3 is a serial number (QB07523967, and QB07524012). Is there any
    reason that this should not work? If it will not, I'm faced with about 100 hours to configure the 6 laptops individually to the charity's requirement.

    Hi,
    This issue can be caused by hard disk settings in bios or DVD drive or bad SATA cable. Please try those steps below:
    Upgrade the BIOS to the latest version; go into the BIOS and activate "Load Fail-Safe Defaults".
    If you connect the SATA drives, please set the SATA controller to compatible mode in BIOS.
    For more information about this issue, please refer to the article:
    http://support.microsoft.com/kb/2466753
    Andy Altmann
    TechNet Community Support

  • WDS "windows setup could not configure Windows on this computer's hardware"

    I use WDS on a 2008 R2 server to deploy Windows 7 Enterprise with SP1 64-bit custom images to a variety of devices within our enterprise. This has worked flawlessly for two years. I have three desktop models and three laptop models (all HP) that share
    a common .wim image. I PXE boot a desktop and choose the image file to deploy. It deploys like magic - until this past week. HP sent us a replacement drive for warranty repair on one computer and on that one PC I started seeing the "Windows setup
    could not configure Windows on this computer's hardware" message after deploying Windows 7. The image deploys just fine, the computer reboots just fine, services are set up, all devices are detected. As soon as "Setup is installing devices" hits
    100% and the "Setup is applying system settings" phase begins, that message appears. After researching the error and pulling the logs that Microsoft's KB 2466753 describes, it seemed that my problem was related to an "Advanced Format"
    disk in that new computer. What I don't get is that they state that this problem was resolved in SP1 (which is what I'm deploying!). So, I started downloading storage drivers to my boot image thinking that maybe a newer driver would fix things. Eventually
    (many drivers later), I got the new hard drive to successfully take my Windows 7 image. Here's where it all went to pieces. No sooner had I corrected the problem on that ONE machine, that none of my other machines would successfully re-image. After
    2 years of flawless operation, now all my computer models exhibit this same error (except the one with the new replacement drive). After recreating my boot image in WDS (being sure to pull it from a Win 7 SP1 DVD) and adding every driver in WDS practically,
    I've gotten all but one particular model to successfully image. No matter what drivers I add (keep in mind, that no drivers have been removed
    from WDS during any of this process), the HP z210 desktops I use will not accept the image. Microsoft suggests flipping BIOS settings but why the heck would I want to do that on every machine when their BIOS settings have never been a problem
    before this? They also say I should only need to download special Intel drivers if my disks are set up with RAID - which they are not. Anyway, as a test, I inserted a standard Windows 7 Enterprise with SP1 64-bit DVD (same one I used to extract my boot.wim)
    and installed Windows on that model with no trouble at all. I only get this error when deploying through WDS. I'm at my wits end and would appreciate any and all help at this point.  Thank you!

    Hi,
    Based on my understanding, the current situation is all other computers deployment is fine but z210 desktops.
    If so, it seems like you have the incorrect driver in WDS for that particular computer z210 desktops you used.
    I suggest install it from WDS without driver for test.
    In addition, you can post this issue in 
    Setup Deployment to check the WDS setting issue.
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Installation problem because errer message of "WINDOWS SETUP COULD NOT CONFIGURE WINDOWS TO RUN ON THIS COMPUTER'S HARDWARE"

    Respected Sir, 
    My name is Md. Naushad, contact No- 9436507010.
    Sir, hamara ek shopping mall hain, jismein ek server and 5 nos. cash counter clint pc hein, server ju computer hein ismain hamne WINDOWS SMALL BUSINESS SERVER 2008 original os use kar raha ho, yein server calte hue humnein pehele bhi 3-4 bar format korke
    dubara ready kiya tha, job koi problem huta tha tu, kuch din pehele se server mein firse problem ho rahi thi (server open nehi hu rahi thi, tu hamne data backup leke pehele jis tarha se server install kiya tha usi tarha se humne install karne ki kusis ki tha,
    tu jab humne windows small business server 2008 software ka original disc-1 se installation start karti hu tu kuch der install huke ek error message aaa rahi hein, ju ki "WINDOWS SETUP COULD NOT CONFIGURE WINDOWS TO RUN ON THIS COMPUTER'S HARDWARE."
    yein message aa rahi hein, jiske baad server installation bech mein hi band hi jati hein, jiske karon hum server ready kar nahi pa rahi ho, so plz help me, ta ki mein server ku firse install kar sakti ho. 
    we wait for ur valuable response, plz help us sir.
    Thank u.

    Hi,
    Sorry for my delay.
    Based on the error message, please refer to following similar thread and KB, then check if can help you.
    SBS
    2008 SP2 " Windows Setup could not configure Windows on this computer’s hardware"
    “Windows Setup could not configure Windows on this computer’s
    hardware” installation error on a Windows 7-based or a Windows Server 2008 R2-based computer
    However,
    please understand that these forums will provide support in English. Since we do not familiar with this language which you use to describe this issue, it is very difficult
    for us to help you with your question. If you could ask your question in English, I will be very happy to help.
    If the issue is urgent to your business, it is recommended that you contact Microsoft Product Support Services
    via telephone so that a dedicated Support Professional can assist you recover the server in a more efficient manner. Please be advised that contacting phone support will be a charged call.
    To obtain the phone numbers for specific technology request please take a look at the web site listed below.
    http://support.microsoft.com/contactus/?ws=support&ln=en-us
    If you are outside the US please see
    http://support.microsoft.com/ for
    regional support phone numbers.
    Thanks for your understanding.
    Hope this helps.
    Best regards,
    Justin Gu

  • Windows setup could not configure windows to run on this computer hardware

    As I was trying to reinstall win 7 on my HP Pavilion dv6-7028tx Enterta laptop, upon competition, I was given this message by win7 saying that " windows setup could not configure windows on this computer's hardwear". 
    I did some research on this issue, it appeared to be the lack of SATA drivers on my computer.　
    Could you please advise me which intel SATA driver should I installed to fix the problem?
    If this method doesn’t work, then can you please tell me how to change the BIOS hard disk drive setting to AHCI or IDE?
    Many thanks
    This question was solved.
    View Solution.

    Hi:
    You can't change the drive controller setting in the BIOS on any HP consumer notebook made in the last 5 - 6 years or so.
    See if this works...
    Download the drivers from this link below (first file listed --  64 bit).
    https://downloadcenter.intel.com/Detail_Desc.aspx?​agr=Y&ProdId=2101&DwnldID=23060&keyword=Intel+Rap...
    Extract (copy) the files onto a usb flash drive without any folders.
    With the flash drive and W7 installation media in the machine, boot from the W7 installation media.
    After you select the install now option, select the Drive Options - Advanced menu, then select the Load Driver option.
    You should now see the storage driver files listed.
    If you check the box, it will only include the compatible driver.
    Follow the prompts and hopefully, W7 will install.

  • OSD: setup windows and configuration manager

    Hi,
    Please advise on setup Windows and configuration manager in SCCM 2012 task sequence.
    I have SMSCachesize=8000 then space SMSMP=ourserver.domain.com then space FSP=ourserver.domain.com
    Just want to verify this is correct. Settings are not one beneith the other. I can do that but if you make the screen of task sequence bigger, settings shuffle
    Please advise.
    J.
    Jan Hoedt

    To add multiple parameters you add Space, that is how it works. For more info you can visit:
    http://technet.microsoft.com/en-us/library/hh846237.aspx#BKMK_SetupWindowsandConfigMgr
    http://technet.microsoft.com/en-us/library/048dbf2d-5132-4fc0-ad8a-d90322b6db96#BKMK_CCMSetupCommandLine
    Regards, Manohar Pusala

  • Why Creative site doesn't have Speaker setup console installer?

    I mean they ship with install disc with Vista version and they expect it to work perfect with Windows 7 or upcoming Windows 8? I want Creative to post there thx console setup or speaker console setup standalone installer on there website. So it would be easy for everyone to download the latest version(if they have updated).

    Well, nobody seems to have this problem?

  • Cisco UCM 8.5.1 integrated with ARC server 5.1 for console services-configuration of ARC secondary subscriber

    We have a setup wherein we have integrated ARC server for exchange console services to the call manager.In our cluster CTI Manager services are running on two subscribers-one of them is a primary and the other is secondary.Similary , we have ARC server installed on a primary server and a secondary server.ARC Server  uses TAPI and CISCO TSP to integrae with the call manager.In the secondary ARC server, when we go to to ARC aConnect admionistration- console connect-Queue location we see the the same queue location numbers as configured in primary ARC server.When we try to change the queue location numbers, it fails to update ,throws up a pop up which says"Queue location cannot be pointed to a routing device.Kindly select a different number".Could you suggest where the conflict might have been occuring and how can we update the queue location numbers in ARC secondary server?Could you also please explain how the CISCO TSP and TAPI function together?

    Thanks a lot Brad,
    All is working, just a couple of question, i'm also using voice recognition, it works but it doens't has the
    play external messages option, is there any specific i have to set or say?
    The touchtone command in my classic conversation is not 7 but i have to execute a little procedure following the
    menu, somenthing like 0 --> 9 --> 1 ---> 7 ( external message option ) --> 1
    Is there any way to change or abbreviate this ?
    Thanks again
    Michele

Maybe you are looking for