TI4600 Stability

Hi,
I have a MSI GF4 TI 4600 in my PC and I have just recently upgraded my processors to use the full capabilities of the card.
Current Setup:
 - Gigabyte - GA6VTXD - Motherboard Running Dual PIII 1.4's
 - MSI 8872
 - 756Mb Ram (PC150)
 - Seagate Barra IV's
 - OS Win XP  with NVidia 29.42 drivers
Hence I would like to play the games at reasonable resolutions (1024x768 and up) but I am finding that when I up the resolution from 800x600 (or lower) the machine simply is locking up.  
I have been running SETI for hours, and no lock ups, but when going into Nascar 2002, it will lock immediately at 1024x768, but runs fine on 800x600 (x16), and will lock after a while on 800x600x32.
It is very strange, if anyone has any suggestions of what to try it would be appreciated.
AP.

I have a similar problem with my MS-8872.   :(  I have, however, spent a week carefully isolating the problem.
Problem symptoms:
1) During DVD playback (using the bundled MSIDVD (InterVideo WinDVD) 3.1 or a copy of InterVideo WinDVD 4.0), the machine totally locks-up after 0-40 minutes of playback.  The only remaining operating interface is the power/reset buttons.  It has been repeatedly observed that after ~15 minutes of being locked up, the machine reboots itself.
2) During looping MPEG playback in Apple QuickTime 5 and 6, the above described lock-up is generated.
3) During play of the bundled games (AquaNox, sacrifice, and No One Lives Forever (1)), the above described lock-up is generated.
Relevant Hardware:
Gigabyte GA-7VRXP V.2.0 (with F11 BIOS -- disabled all USB, serial, parallel, IDE RAID, Ethernet, audio, 2nd IDE)
Athlon XP 1800+
2 x 512MB DDR/266 ECC registered SDRAM DIMMs
MSI GF4 Ti 4600 (MS-8872)
Relevant software:
Win98SE
DirectX 8.1b
(media players and games as listed above)
Relevant drivers:
Via 4-in-1 v. 443v
Adaptec FMS v. 3.0.3
nVidia 30.82 (and earlier)
Although additional hardware is present and different BIOS versions and software drivers were used in isolating the problem, in the fully configured machine, the isolation process reduced the machine to this configuration in the process of identifying which component was causing the failure.
With the above configuration, failure was *not* observed by replacing the video card with:
    Diamond V770 Ultra (TNT2 Ultra, 32MB),
    Eagle GeForce3 Ti 500 (64MB), or
    ChainTech GeForce4 Ti 4600 (128MB).
In all these cases, the machine was able to loop DVD playback, MPEG playback, and idle the above games for >40 consecutive hours.
Therefore, the problem with Ti4600 playback has been isolated to the MSI card.  Further, it has been demonstrated that this is not an issue of interaction with other hardware (none was present).  Finally, it has been shown that substantially similar hardware (the ChainTech card) was able to successfully operate without difficulty.
The following additional remedies were taken:
1) Underclock the MSI video card to its minimal settings.
2) Replace the HD and reinstall the OS and abovementioned software in a minimal configuration.
3) Remove the DVD player and only play back content from the HD (in case the DVD player was causing trouble).
4) Move the MSI card to another machine and observe that identical failure is observed.  (This last was performed as follows: for 13 repetitions, randomly assign the MSI card and the ChainTech card to two substantially different machines.  Start both machines looping the same content.  Observe which machine failed first.  In all 13 cases, the machine with the MSI card failed first.  The probability of this occurring if both cards were equally likely to fail first was 1/8192 ~= 0.012%.)
5) Configured motherboard to be maximally conservative: slowest RAM timings, underclocking the processor and RAM, various combinations of AGP aperture, PCI write combining, et c..., and whatever Gigabyte thinks "Fail-safe" settings are. AGP compensation values were not manually adjusted (as there is no documentation about the effect of this setting from Gigabyte nor the ideal range of this setting from MSI).
Thus, despite extraordinary isolation efforts (not available to most home video enthusiasts), no method was found to eliminate the failure of this card under heavy video load.
Miscellaneous items:
Note that this motherboard (GA-7VRXP) is known to require significant current at 3.3V.  Most GeForce4 Ti cards also require substantial 3.3V peak current.  The power supply in this machine is easily rated to 130% of the stated peak current requirements of all the components at each supplied voltage.  (The original 400W P/S was found to be more suited to driving large HD arrays and was replaced for this reason.)
Question (finally!):
So, how do I make this rather expensive video card outperform the $40 TNT2Ultra I've got lying around as a spare part?

Similar Messages

  • Various 4G / 5G stability problems and now my iPod is USB 1.1 only!

    Hi,
    I bought a brand new iPod a week or two ago and it worked fine for one sync. Then the battery was running low (because I'd been using it!) so I plugged it in and iTunes synced automatically and the battery charged. after the sync I hit "eject" in iTunes so that the battery would just charge.
    I returned to find that the iPod was still mounted! Very strange. I ejected again..... and it seems that what was happening was when the iPod was ejected it simply rebooted and when it came back up was mounted automatically again!
    I ejected and unplugged the iPod and it was no longer stable - I would get to the menu and almost to play a song and it would reset. It seemed like my speed was the limiting factor (i.e. the iPod would only stay up for n seconds), rather than it crashing because I tried a particular function.
    I saw this unstable behaviour with my old iPod (4G, firewire on this same machine) too where I had to reflash it to get it working again reliably.
    So, I reflash the (new) device with the iPod Updater software downloaded for me by Software Update. It resets, and all seems well, with the rather catastrophic exception that now the iPod is only recognised as a USB 1.1 device according to System Profiler! The transfer speed is very very slow.
    This is really a bit of a showstopper for my user experience. I have tried:
    - Resetting my computer
    - Changing the cable (I have two USB2.0 cables and 1 USB2.0/Firewire cable which I have tried all of)
    - Changing USB ports (including taking ALL my USB devices away and plugging the iPod directly into the back of the desktop machine)
    - Reflashing the iPod again
    I have NOT tried:
    - re-downloading the iPod Updater from Apple and using that (I'm downloading it now)
    So.... the questions are:
    - Has the firmware updater somehow made my iPod appear to be a USB1.1 device?
    - Or is this a hardware fault and I need to return the iPod to be fixed?
    - Is this stability problem a commonly observed one?
    - If so what can I do to avoid it?
    Thanks in advance,
    Neil.
    Powermac G4 MDD   Mac OS X (10.4.7)  

    Cannot reproduce presumed fixed

  • Problems with n8-response time , stability and use...

    ive been using n8 for a couple of months now and some times i really think this can do better
    the text editor for messages has the keyboard options just bellow space. i so want that to change because space is a very frequently hit and if i type fast then almost always end up getting the keyboard changed to qwerty .i use alpha numeric off course but why cant this be the same as the s60 one....used to work great on my 5800
    2nd the response gets annoyingly slow if i hit the applications folder
    and again by instinct i end up pressing it double and entering the video editor. i know it can be optimized and would love to see it in the update cause its a matter of quick response. applications and folders should open quick and stability still needs work after the 2 minor updates nokia gave 
    3rd its not stable. some times the notification widget stops notifying although there have been missed events. the WLAN connection widget is bonkers , i was at home and it was showing connection to my uni's AP which is miles away. and it has a mind of its own. also the connection is some how suspended and pages just wont open,same in the case of ovi store. Nokia need to fix that
    if nokia just work on the interface so the fone just flows with fingers then its a damn good fone. im having issues but dont want to let go of it
    camera is great but the interface needs work
    symbian3 is new and the is room for a lot of improvment

    the N8 is a great phone and I'm happy whit it but I must agree with the 2nd part....the respons is sometimes really slow but not painfully and it's really not that offten..
    and I fully agree what you said about camera interface, the camera itself is a great, picures are great in the dark sometimes can be better but the interface is not that good and the cameraphone as N8 shuld have a interface that match camera
    sorry but bad english

  • Core voltage stability on 865PE Neo2 PFS

    I've just installed one of the new P-series NEO-2 MOBO's. Nice piece of work, although it seems there is still some work left to be done. Definite problems (although not serious) in Core center (althoug other posts indicate this may be indiginous to core center itself..)
    More serious though is a reading of the processor core voltage.
    I'm using a Celery 2.6, OC'd to 3.25G, FSB 125. Had to raise core voltage to 1.6V to get there, lower voltage led to crashes as low as FSB 104...
    Recently, I looked at a scan of the core voltage (provided by Speedfan):
    The problem lies in the fact that during disk access and/or high processor load, the core voltage drops as much as 90 mV, bringing it back to its default setting (spikes in graph, longer drop was writing DVD, CPU benchmark has similar result).
    If it does this at 1.5V, I can understand the crashes.
    I get the impression this board could do MUCH better with more stable voltage regulation.
    Anyone seeing similar behaviour in other Neo2-boards? Am I missing a setting?(core-cell may be intervening) It's hard to imagine the PSU can't hack it.. 12V level is rock solid.
    System: MSI 865PE Neo2 PFS, Celeron 2.6G @ 3.25G (125 FSB)
                 1x corsair 3200 512MB @ 333
                 POV 5600 VIVO
                 WD800BB 80GB
    PSU:      HEC 350 VD-PT (3.3V@28A, 5V@33A, 12V@15A)

    I'm not worrying. Just a bit surprised we all make a bug fuzz about overclocking, increasing core voltage by 25 mV at a time, and suddenly ignoring it all and "accepting" 70 mV drops if we need processing power...  
    If the voltage regulator would be more robust, it would be able to maintain the Vcore to (much?) higher power ratings.
    This board drops by roughly 70 mV, constituting 3 notches on the voltage setting tab.
    I went up to 1.6V, and what I actually get is 1.52.....  
    To have 1.6 available under all conditions, I'd need to set to 1.7 (yes, I've tried), which is over the top for "normal" overclocking (not to mention considerably higher temperatures).
    Anyway, I'd like to know what other boards are doing regarding Vcore stability. Anyone out there with additional data?
    Maybe a new target for modifications?  (if it's worth it...)

  • Stability + boot issue MSI X48C Platinum

    Hi,
    I'm using my desktop-pc for quite some time now (since august 2008), but it gave me some problems. One of the last problems was a failing RAID-0 array: one of the Seagate Barracuda's 7200.11 640 GB was failing frequently, while it was already 2x replaced by my supplier for a new product. So I figured RAID-0 simply wasn't possible with these drives, at least not a stabile RAID-0 array, so I switched to a Samsung Spinpoint F3 instead.
    To the point: it took a while before I finally had enough time to re-assembly the new system with the new hard drive. I managed to install the hard drive and installed Windows Vista Ultimate on it (this week), but after the first boot it appeared the system hanged entirely while being idle in Windows (no errors, just black screen). Other problems are: system doesn't boot frequently. I tried to install a fresh copy of Windows 7 Professional x84 as well, but while the installation files are loaded I barely get to the selection screen for system language (succeeded one time in this, mostly it hangs after/during the installation files are loaded from the disc). The original installation DVD of Windows Vista also couldn't be booted anymore, is Russian roulette how far I get.
    Symptons are:
    -while trying to boot from bootable USB/DVD, screen goes to black, fan of graphics card accelarates and monitor goes to stand-by
    -sometimes during boot system fails, after 3 resets motherboard resets itself. This action still doesn't garantue a succesful boot.
    -sometimes the system doesn't boot entirely, just a monitor in stand-by (fans are on, graphics card (HD4870) shows 3 red leds as normal for 1 second)
    -if the system boots, and I don't load bootable in DVD-station or USB-ports, Windows is just started as normal most of the times. In Windows, I installed all necessary drivers, tested the graphics card with furmark and with the 9.11 drivers: stabile no artifacts. I played C&C Generals / Anno 1404, just to see if the graphics card could take it without artifacts. Both games work fine, however while in Windows the system hangs after some period of time, could be 30 minutes, could be 2 hours.
    -added extra cooling fans aimed at motherboard and graphics card with stock cooler on HD4870 on 100%, just to make sure it was not a cooling issue.
    System is:
    processor: Intel E8500 E0
    mainboard: MSI X48C (AMI 7.3, supports E0 revision of processor)
    Memory: Corsair Dominator 4GB PC8500
    GPU: Sapphire Radeon HD4870 512MB (reference)
    Hard drive: Samsung Spinpoint F3 1 TB
    PSU: Cooler Master Real Power M620 (620 watt)
    case: Cooler Master CM690, with 6 120mm case fans (3x Scythe S-Flex 1900 RPM)
    Question:
    What could possible cause all these problems? I first feared it was something with my graphics card as the monitor went to black entirely and to stand-by (no input signals could be detected anymore) and as the fan of the graphics card accelerates as well), but now I've narrowed it down to:
    -mainboard (may explain previous problems with the SATA controller as well, with 3 different hard drives now)
    -PSU (strange, as it gets through post and does boot occasionaly)
    -memory (could be, will verify if the systems does the same with another DDR2 set later this week, but I don't expect this to be the case)
    -CPU (how to damage this CPU at stock speeds, with a properly mounted Thermalright Ultra 120 Extreme and a S-Flex 1200 RPM as cooling)

    Added to signature.
    I first used the Power Supply test of OCCT, which puts a 100% on both the processor and graphics card to simulate the toughest conditions for the PSU. It crashed within 5 seconds. So I tested the system with OCCT v3.1.0, using CPU only: OCCT (testing processor at 100% load). Test ran for 60 minutes: not a single error. So with the two tests combined the system crashes, with only the CPU test the system does not. So I switched to the GPU: OCCT test (testing graphics card at 100% load) for one hour: also no problems after 1 hour testing. 12V dropped a bit during these last tests, but within safety limits I reckon:
    Later this week I'm propably ordering a Corsair 520 / 620 / 650 watt model, so I can test with a new PSU. Meanwhile I'll see if the system is stable for longer periods of time, I'm currently trying to verify if it was just bad luck the system freezed within 5 seconds the first time, or if it has to do with other things.
    [edit]
    Perhaps I should add as well that the environment temperature has been decreased as well here: from 15 degrees Celsius it's not freezing with -4 degrees Celsius outside. Room temperature dropped 5 degrees I guess when I compare the last test circumstances and the current test circumstances. Temperatures of CPU and GPU don't seem to be largely influenced by this, but perhaps the temperatures of the RAM and/or VRM are lower now with other components.
    [edit2]
    The CPU and GPU test combined (PSU test) gave an error after 5 minutes now, with every component at stock settings (so also stock fan speeds). Retesting with graphics card fan at 100% now. I noticed that there was some variation on the 12V line during the test (within both marges), but from 11.88 to 12.14 volt.

  • Neo2 platinum Encountering Stability Problems /w dual channel memory

    Hello,
    Recently I built my first computer ever, see bottom.  After getting windows installed I then had problems with installing other programs and general stability issues.  I tried reinstalling windows and after the reinstall I got the same problems.
    Something to do with the instability is when I start it up, and go into BIOS, it states my Athlon 64 3500+ as running at 2211, a half percent overclock.  Also, even though I have the FSB set as 200mhz, when I go into CoreCenter on windows it states the FSB as being set 201mhz.  In the nVidia system utility, it states my memory as running at 402mhz, and I had to crank that down to 400mhz to get stability, it allowed my to install programs without error, but there were still stability problems like crashes(blue screen, the computer just plain restarting without notice).  I took out one of my memory cards, both of them work alone though, I've ran memory test utilities.  That had a good effect and the computer runs fairly stable, but I still have problems, and I want to be able to take advantage of dual channel.  I'm running my memory on auto and it's using the times of 2-3-3-6-2T.
    Another problem I'm experiencing is the AC97 audio not being detected and loaded by windows, it will say I have no audio device, and the speaker will not show up in the notification area in the bottom right-hand corner.  This happens inconsistantly.
                               -Thank You
    AMD Athlon 64 3500+
    MSI Neo2 Platinum(nForce3 939 socket)rev1.0 BIOS 1.4
    2x Mushkin DDR400 512mb CL2 Blue
    BFG GeForce6800GT OC
    80gb Hitachi Deskstar SATA

    hi bknoll,
    welcome to the forum.
    1) i wouldn't worry overmuch at the 201 issue.
    2) Quote
    I've ran memory test utilities. That had a good effect and the computer runs fairly stable, but I still have problems
    which test utilities did you use, Don't quiet understand  Quote
    had a good effect and the computer runs fairly stable
    3) It may be worth checking the Mushkin site or any documentation you have to verify that the auto settings agree with the quoted settings for the modules. It's not unkown for errors to occur when the memory controller on the CPU to misinterpret the SPD chip setting on your sticks - this is where the auto settings come from. Some memory like certain corsair modules need to run at different settings on AMD64, thus auto timings must be overidden,
    4) Have you installed the Realtek drivers from the CD, & enabled onboard sound in Bios. When these are done normally there's the MSI Sound Effect manager in control panel. you just need to set your speaker config in the Windows Sounds & Audio Devices.
    5) Usual question What power supply are you using as been underpowered on the 12v rail in particular can be the cause of crashes,

  • Stability issues: MSI ATI Radeon HD 6970 2048MB Twin Frozr III

    Evening all, been having some issues with my recently purchased MSI card. I'm inclined to think there is damage/issues with the video memory on the card.
    I did some quick research on the card and it seems that the model i have was originally a reference version of the 6970 Lightning which was given a factory go-over and re-branded. This may account for the heatsink/fan assembly being loose, some scratches on some of the surfaces and dust build up on the rear of the card.
    I have had the card in my rig for over a week now and stability has been an issue through this period. After reading a few threads online I set a custom fan graph using MSI Afterburner and regularly monitor GPU temps. DxDiag shows the card to have 1774MB Approx total memory, which i find worrying given the card specs state it should read 2048BM.
    The driver crashes occur both when the card is idle and under load with no obvious cause. The GPU clock is stock 880Mhz and i have lowered the memory clock to 1300 (stock: 1375) in an attempt to improve stability, so far this has shown some success.
    Can anyone give me some advice as to if this is likely a hardware issue or driver based? Also any recommendations on how to improve stability other than getting a new card (i have no more money to spend on replacement parts).
    Thank you for your time
    MSI Afterburner ver: 2.1.0
    GFX Driver ver: 7.14.10.0887 Catalyst 12.1
    GPU core clock: 880
    Memory clock: 1300
    Core Voltage: stock
    DxDiag info:
    Code: [Select]
    System Information
    Time of this report: 2/15/2012, 17:44:35
           Machine name: SCREV-PC
       Operating System: Windows 7 Ultimate 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.110622-1506)
               Language: English (Regional Setting: English)
    System Manufacturer: System manufacturer
           System Model: System Product Name
                   BIOS: BIOS Date: 05/27/11 13:46:06 Ver: 17.04
              Processor: AMD Phenom(tm) II X6 1055T Processor (6 CPUs), ~2.8GHz
                 Memory: 8192MB RAM
    Available OS Memory: 8192MB RAM
              Page File: 4009MB used, 12370MB available
            Windows Dir: C:\Windows
        DirectX Version: DirectX 11
    DX Setup Parameters: Not found
       User DPI Setting: Using System DPI
     System DPI Setting: 96 DPI (100 percent)
        DWM DPI Scaling: Disabled
         DxDiag Version: 6.01.7601.17514 64bit Unicode
    DxDiag Notes
          Display Tab 1: No problems found.
          Display Tab 2: No problems found.
            Sound Tab 1: No problems found.
            Sound Tab 2: No problems found.
            Sound Tab 3: No problems found.
              Input Tab: No problems found.
    DirectX Debug Levels
    Direct3D:    0/4 (retail)
    DirectDraw:  0/4 (retail)
    DirectInput: 0/5 (retail)
    DirectMusic: 0/5 (retail)
    DirectPlay:  0/9 (retail)
    DirectSound: 0/5 (retail)
    DirectShow:  0/6 (retail)
    Display Devices
              Card name: AMD Radeon HD 6900 Series
           Manufacturer: Advanced Micro Devices, Inc.
              Chip type: ATI display adapter (0x6718)
               DAC type: Internal DAC(400MHz)
             Device Key: Enum\PCI\VEN_1002&DEV_6718&SUBSYS_23701462&REV_00
         Display Memory: 1774 MB
       Dedicated Memory: 2030 MB
          Shared Memory: 3839 MB
           Current Mode: 1680 x 1050 (32 bit) (60Hz)
           Monitor Name: Generic PnP Monitor
          Monitor Model: L226WTQ
             Monitor Id: GSM564E
            Native Mode: 1680 x 1050(p) (59.883Hz)
            Output Type: DVI
            Driver Name: aticfx64.dll,aticfx64.dll,aticfx64.dll,aticfx32,aticfx32,aticfx32,atiumd64.dll,atidxx64.dll,atidxx64.dll,atiumdag,atidxx32,atidxx32,atiumdva,atiumd6a.cap,atitmm64.dll
    Driver File Version: 8.17.0010.1114 (English)
         Driver Version: 8.930.0.0
            DDI Version: 11
           Driver Model: WDDM 1.1
      Driver Attributes: Final Retail
       Driver Date/Size: 12/6/2011 03:16:00, 933888 bytes
            WHQL Logo'd: Yes
        WHQL Date Stamp:
      Device Identifier: {D7B71EE2-2458-11CF-8873-7A03BEC2C535}
              Vendor ID: 0x1002
              Device ID: 0x6718
              SubSys ID: 0x23701462
            Revision ID: 0x0000
     Driver Strong Name: oem24.inf:ATI.Mfg.NTamd64.6.1:ati2mtag_NICayman:8.930.0.0:pci\ven_1002&dev_6718
         Rank Of Driver: 00E62001
            Video Accel: ModeMPEG2_A ModeMPEG2_C
       Deinterlace Caps: {6E8329FF-B642-418B-BCF0-BCB6591E255F}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY
                         {6E8329FF-B642-418B-BCF0-BCB6591E255F}: Format(In/Out)=(UYVY,UYVY) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(UYVY,UYVY) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(UYVY,UYVY) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(YV12,0x32315659) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {3C5323C1-6FB7-44F5-9081-056BF2EE449D}: Format(In/Out)=(NV12,0x3231564e) Frames(Prev/Fwd/Back)=(0,0,2) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
                         {552C0DAD-CCBC-420B-83C8-74943CF9F1A6}: Format(In/Out)=(NV12,0x3231564e) Frames(Prev/Fwd/Back)=(0,0,2) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
                         {6E8329FF-B642-418B-BCF0-BCB6591E255F}: Format(In/Out)=(NV12,0x3231564e) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(NV12,0x3231564e) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(NV12,0x3231564e) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC1,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC2,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC3,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC4,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(S340,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(S342,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
           D3D9 Overlay: Not Supported
                DXVA-HD: Not Supported
           DDraw Status: Enabled
             D3D Status: Enabled
             AGP Status: Enabled
              Card name: AMD Radeon HD 6900 Series
           Manufacturer: Advanced Micro Devices, Inc.
              Chip type: ATI display adapter (0x6718)
               DAC type: Internal DAC(400MHz)
             Device Key: Enum\PCI\VEN_1002&DEV_6718&SUBSYS_23701462&REV_00
         Display Memory: 1774 MB
       Dedicated Memory: 2030 MB
          Shared Memory: 3839 MB
           Current Mode: 1920 x 1080 (32 bit) (60Hz)
           Monitor Name: Generic PnP Monitor
          Monitor Model: E2240
             Monitor Id: GSM57A4
            Native Mode: 1920 x 1080(p) (60.000Hz)
            Output Type: DVI
            Driver Name: aticfx64.dll,aticfx64.dll,aticfx64.dll,aticfx32,aticfx32,aticfx32,atiumd64.dll,atidxx64.dll,atidxx64.dll,atiumdag,atidxx32,atidxx32,atiumdva,atiumd6a.cap,atitmm64.dll
    Driver File Version: 8.17.0010.1114 (English)
         Driver Version: 8.930.0.0
            DDI Version: 11
           Driver Model: WDDM 1.1
      Driver Attributes: Final Retail
       Driver Date/Size: 12/6/2011 03:16:00, 933888 bytes
            WHQL Logo'd: Yes
        WHQL Date Stamp:
      Device Identifier: {D7B71EE2-2458-11CF-8873-7A03BEC2C535}
              Vendor ID: 0x1002
              Device ID: 0x6718
              SubSys ID: 0x23701462
            Revision ID: 0x0000
     Driver Strong Name: oem24.inf:ATI.Mfg.NTamd64.6.1:ati2mtag_NICayman:8.930.0.0:pci\ven_1002&dev_6718
         Rank Of Driver: 00E62001
            Video Accel: ModeMPEG2_A ModeMPEG2_C
       Deinterlace Caps: {6E8329FF-B642-418B-BCF0-BCB6591E255F}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY
                         {6E8329FF-B642-418B-BCF0-BCB6591E255F}: Format(In/Out)=(UYVY,UYVY) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(UYVY,UYVY) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(UYVY,UYVY) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(YV12,0x32315659) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {3C5323C1-6FB7-44F5-9081-056BF2EE449D}: Format(In/Out)=(NV12,0x3231564e) Frames(Prev/Fwd/Back)=(0,0,2) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
                         {552C0DAD-CCBC-420B-83C8-74943CF9F1A6}: Format(In/Out)=(NV12,0x3231564e) Frames(Prev/Fwd/Back)=(0,0,2) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
                         {6E8329FF-B642-418B-BCF0-BCB6591E255F}: Format(In/Out)=(NV12,0x3231564e) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(NV12,0x3231564e) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(NV12,0x3231564e) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC1,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC2,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC3,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC4,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(S340,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(S342,UNKNOWN) Frames(Prev/Fwd/Back)=(0,0,0) Caps=
           D3D9 Overlay: Not Supported
                DXVA-HD: Not Supported
           DDraw Status: Enabled
             D3D Status: Enabled
             AGP Status: Enabled
    DirectInput Devices
          Device Name: Mouse
             Attached: 1
        Controller ID: n/a
    Vendor/Product ID: n/a
            FF Driver: n/a
          Device Name: Keyboard
             Attached: 1
        Controller ID: n/a
    Vendor/Product ID: n/a
            FF Driver: n/a
    Poll w/ Interrupt: No
    USB Devices
    + USB Root Hub
    | Vendor/Product ID: 0x1002, 0x4397
    | Matching Device ID: usb\root_hub
    | Service: usbhub
    | Driver: usbhub.sys, 3/25/2011 03:29:26, 343040 bytes
    | Driver: usbd.sys, 3/25/2011 03:28:59, 7936 bytes
    Disk & DVD/CD-ROM Drives
          Drive: C:
     Free Space: 69.8 GB
    Total Space: 122.1 GB
    File System: NTFS
          Model: M4-CT128M4SSD2 ATA Device
          Drive: D:
     Free Space: 104.7 GB
    Total Space: 238.5 GB
    File System: NTFS
          Model: WDC WD2500KS-00MJB0 ATA Device
          Drive: E:
     Free Space: 1146.7 GB
    Total Space: 1907.6 GB
    File System: NTFS
          Model: ST32000542AS ATA Device
          Drive: F:
     Free Space: 153.5 GB
    Total Space: 238.4 GB
    File System: NTFS
          Model: WDC WD2500AAKS-00L9A0 ATA Device
          Drive: H:
     Free Space: 0.1 GB
    Total Space: 0.1 GB
    File System: NTFS
          Model: WDC WD2500AAKS-00L9A0 ATA Device
          Drive: I:
          Model: PCZMDO PMJWLERWL SCSI CdRom Device
         Driver: c:\windows\system32\drivers\cdrom.sys, 6.01.7601.17514 (English), 11/20/2010 09:19:21, 147456 bytes
          Drive: G:
          Model: TSSTcorp CD/DVDW SH-S183L ATA Device
         Driver: c:\windows\system32\drivers\cdrom.sys, 6.01.7601.17514 (English), 11/20/2010 09:19:21, 147456 bytes
    System Devices
         Name: PCI standard host CPU bridge
    Device ID: PCI\VEN_1022&DEV_9601&SUBSYS_843E1043&REV_00\3&267A616A&0&00
       Driver: n/a
         Name: PCI standard ISA bridge
    Device ID: PCI\VEN_1002&DEV_439D&SUBSYS_84431043&REV_40\3&267A616A&0&A3
       Driver: C:\Windows\system32\DRIVERS\msisadrv.sys, 6.01.7600.16385 (English), 7/14/2009 01:48:27, 15424 bytes
         Name: Standard Enhanced PCI to USB Host Controller
    Device ID: PCI\VEN_1002&DEV_4396&SUBSYS_84431043&REV_00\3&267A616A&0&92
       Driver: C:\Windows\system32\drivers\usbehci.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:04, 52736 bytes
       Driver: C:\Windows\system32\drivers\usbport.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:14, 325120 bytes
       Driver: C:\Windows\system32\drivers\usbhub.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:26, 343040 bytes
         Name: NEC Electronics USB 3.0 Host Controller
    Device ID: PCI\VEN_1033&DEV_0194&SUBSYS_84131043&REV_03\FFFFFFFFFFFFFFFF00
       Driver: C:\Windows\system32\DRIVERS\nusb3xhc.sys, 1.00.0019.0000 (English), 1/22/2010 12:22:22, 180224 bytes
         Name: PCI standard host CPU bridge
    Device ID: PCI\VEN_1022&DEV_1204&SUBSYS_00000000&REV_00\3&267A616A&0&C4
       Driver: n/a
         Name: Standard Dual Channel PCI IDE Controller
    Device ID: PCI\VEN_1002&DEV_439C&SUBSYS_84431043&REV_40\3&267A616A&0&A1
       Driver: C:\Windows\system32\DRIVERS\pciide.sys, 6.01.7600.16385 (English), 7/14/2009 01:45:45, 12352 bytes
       Driver: C:\Windows\system32\DRIVERS\pciidex.sys, 6.01.7600.16385 (English), 7/14/2009 01:45:46, 48720 bytes
       Driver: C:\Windows\system32\DRIVERS\atapi.sys, 6.01.7600.16385 (English), 7/14/2009 01:52:21, 24128 bytes
       Driver: C:\Windows\system32\DRIVERS\ataport.sys, 6.01.7601.17514 (English), 11/20/2010 13:32:46, 155520 bytes
         Name: Standard Dual Channel PCI IDE Controller
    Device ID: PCI\VEN_1002&DEV_4390&SUBSYS_84431043&REV_40\3&267A616A&0&88
       Driver: C:\Windows\system32\DRIVERS\pciide.sys, 6.01.7600.16385 (English), 7/14/2009 01:45:45, 12352 bytes
       Driver: C:\Windows\system32\DRIVERS\pciidex.sys, 6.01.7600.16385 (English), 7/14/2009 01:45:46, 48720 bytes
       Driver: C:\Windows\system32\DRIVERS\atapi.sys, 6.01.7600.16385 (English), 7/14/2009 01:52:21, 24128 bytes
       Driver: C:\Windows\system32\DRIVERS\ataport.sys, 6.01.7601.17514 (English), 11/20/2010 13:32:46, 155520 bytes
         Name: VIA 1394 OHCI Compliant Host Controller
    Device ID: PCI\VEN_1106&DEV_3403&SUBSYS_83741043&REV_00\001E8CFFFFDA199000
       Driver: C:\Windows\system32\DRIVERS\1394ohci.sys, 6.01.7601.17514 (English), 11/20/2010 10:44:56, 229888 bytes
         Name: PCI standard host CPU bridge
    Device ID: PCI\VEN_1022&DEV_1203&SUBSYS_00000000&REV_00\3&267A616A&0&C3
       Driver: n/a
         Name: Standard OpenHCD USB Host Controller
    Device ID: PCI\VEN_1002&DEV_4399&SUBSYS_84431043&REV_00\3&267A616A&0&A5
       Driver: C:\Windows\system32\drivers\usbohci.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:04, 25600 bytes
       Driver: C:\Windows\system32\drivers\usbport.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:14, 325120 bytes
       Driver: C:\Windows\system32\drivers\usbhub.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:26, 343040 bytes
         Name: ATI I/O Communications Processor SMBus Controller
    Device ID: PCI\VEN_1002&DEV_4385&SUBSYS_00000000&REV_41\3&267A616A&0&A0
       Driver: n/a
         Name: PCI standard PCI-to-PCI bridge
    Device ID: PCI\VEN_1022&DEV_9609&SUBSYS_843E1043&REV_00\3&267A616A&0&50
       Driver: C:\Windows\system32\DRIVERS\pci.sys, 6.01.7601.17514 (English), 11/20/2010 13:33:48, 184704 bytes
         Name: PCI standard host CPU bridge
    Device ID: PCI\VEN_1022&DEV_1202&SUBSYS_00000000&REV_00\3&267A616A&0&C2
       Driver: n/a
         Name: Standard OpenHCD USB Host Controller
    Device ID: PCI\VEN_1002&DEV_4397&SUBSYS_84431043&REV_00\3&267A616A&0&B0
       Driver: C:\Windows\system32\drivers\usbohci.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:04, 25600 bytes
       Driver: C:\Windows\system32\drivers\usbport.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:14, 325120 bytes
       Driver: C:\Windows\system32\drivers\usbhub.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:26, 343040 bytes
         Name: ATI I/O Communications Processor PCI Bus Controller
    Device ID: PCI\VEN_1002&DEV_4384&SUBSYS_00000000&REV_40\3&267A616A&0&A4
       Driver: C:\Windows\system32\DRIVERS\pci.sys, 6.01.7601.17514 (English), 11/20/2010 13:33:48, 184704 bytes
         Name: Standard Dual Channel PCI IDE Controller
    Device ID: PCI\VEN_1106&DEV_0415&SUBSYS_838F1043&REV_00\004063FFFF63400000
       Driver: C:\Windows\system32\DRIVERS\pciide.sys, 6.01.7600.16385 (English), 7/14/2009 01:45:45, 12352 bytes
       Driver: C:\Windows\system32\DRIVERS\pciidex.sys, 6.01.7600.16385 (English), 7/14/2009 01:45:46, 48720 bytes
       Driver: C:\Windows\system32\DRIVERS\atapi.sys, 6.01.7600.16385 (English), 7/14/2009 01:52:21, 24128 bytes
       Driver: C:\Windows\system32\DRIVERS\ataport.sys, 6.01.7601.17514 (English), 11/20/2010 13:32:46, 155520 bytes
         Name: PCI standard PCI-to-PCI bridge
    Device ID: PCI\VEN_1022&DEV_9608&SUBSYS_843E1043&REV_00\3&267A616A&0&48
       Driver: C:\Windows\system32\DRIVERS\pci.sys, 6.01.7601.17514 (English), 11/20/2010 13:33:48, 184704 bytes
         Name: PCI standard host CPU bridge
    Device ID: PCI\VEN_1022&DEV_1201&SUBSYS_00000000&REV_00\3&267A616A&0&C1
       Driver: n/a
         Name: Standard OpenHCD USB Host Controller
    Device ID: PCI\VEN_1002&DEV_4397&SUBSYS_84431043&REV_00\3&267A616A&0&98
       Driver: C:\Windows\system32\drivers\usbohci.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:04, 25600 bytes
       Driver: C:\Windows\system32\drivers\usbport.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:14, 325120 bytes
       Driver: C:\Windows\system32\drivers\usbhub.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:26, 343040 bytes
         Name: High Definition Audio Controller
    Device ID: PCI\VEN_1002&DEV_4383&SUBSYS_841B1043&REV_40\3&267A616A&0&A2
       Driver: C:\Windows\system32\DRIVERS\hdaudbus.sys, 6.01.7601.17514 (English), 11/20/2010 10:43:43, 122368 bytes
         Name: AK6I472Y IDE Controller
    Device ID: PCI\VEN_1101&DEV_9502&SUBSYS_482FFC12&REV_01\4&5D18F2DF&0
       Driver: n/a
         Name: PCI standard PCI-to-PCI bridge
    Device ID: PCI\VEN_1022&DEV_9607&SUBSYS_843E1043&REV_00\3&267A616A&0&38
       Driver: C:\Windows\system32\DRIVERS\pci.sys, 6.01.7601.17514 (English), 11/20/2010 13:33:48, 184704 bytes
         Name: PCI standard host CPU bridge
    Device ID: PCI\VEN_1022&DEV_1200&SUBSYS_00000000&REV_00\3&267A616A&0&C0
       Driver: n/a
         Name: Standard OpenHCD USB Host Controller
    Device ID: PCI\VEN_1002&DEV_4397&SUBSYS_84431043&REV_00\3&267A616A&0&90
       Driver: C:\Windows\system32\drivers\usbohci.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:04, 25600 bytes
       Driver: C:\Windows\system32\drivers\usbport.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:14, 325120 bytes
       Driver: C:\Windows\system32\drivers\usbhub.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:26, 343040 bytes
         Name: PCI standard PCI-to-PCI bridge
    Device ID: PCI\VEN_1022&DEV_9605&SUBSYS_843E1043&REV_00\3&267A616A&0&28
       Driver: C:\Windows\system32\DRIVERS\pci.sys, 6.01.7601.17514 (English), 11/20/2010 13:33:48, 184704 bytes
         Name: High Definition Audio Controller
    Device ID: PCI\VEN_1002&DEV_AA80&SUBSYS_AA801462&REV_00\4&6E074CE&0&0110
       Driver: C:\Windows\system32\DRIVERS\hdaudbus.sys, 6.01.7601.17514 (English), 11/20/2010 10:43:43, 122368 bytes
         Name: Standard Enhanced PCI to USB Host Controller
    Device ID: PCI\VEN_1002&DEV_4396&SUBSYS_84431043&REV_00\3&267A616A&0&B2
       Driver: C:\Windows\system32\drivers\usbehci.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:04, 52736 bytes
       Driver: C:\Windows\system32\drivers\usbport.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:14, 325120 bytes
       Driver: C:\Windows\system32\drivers\usbhub.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:26, 343040 bytes
         Name: Realtek PCIe GBE Family Controller #2
    Device ID: PCI\VEN_10EC&DEV_8168&SUBSYS_84321043&REV_06\01000000684CE00000
       Driver: n/a
         Name: PCI standard PCI-to-PCI bridge
    Device ID: PCI\VEN_1022&DEV_9603&SUBSYS_843E1043&REV_00\3&267A616A&0&10
       Driver: C:\Windows\system32\DRIVERS\pci.sys, 6.01.7601.17514 (English), 11/20/2010 13:33:48, 184704 bytes
         Name: AMD Radeon HD 6900 Series
    Device ID: PCI\VEN_1002&DEV_6718&SUBSYS_23701462&REV_00\4&6E074CE&0&0010
       Driver: C:\Windows\system32\DRIVERS\atikmdag.sys, 8.01.0001.1223 (English), 12/6/2011 03:45:40, 10720256 bytes
       Driver: C:\Windows\system32\DRIVERS\ati2erec.dll, 1.00.0000.0023 (English), 12/6/2011 02:10:24, 53248 bytes
       Driver: C:\Windows\system32\DRIVERS\atikmpag.sys, 8.14.0001.6248 (English), 12/6/2011 02:12:14, 327168 bytes
       Driver: C:\Windows\system32\atiumd64.dll, 7.14.0010.0887 (English), 12/6/2011 02:24:02, 7511040 bytes
       Driver: C:\Windows\system32\atiumd6a.dll, 8.14.0010.0342 (English), 12/6/2011 02:39:12, 4072960 bytes
       Driver: C:\Windows\system32\atitmm64.dll, 6.14.0011.0023 (English), 12/6/2011 03:10:38, 120320 bytes
       Driver: C:\Windows\system32\atiicdxx.dat, 11/14/2011 19:47:22, 608507 bytes
       Driver: C:\Windows\system32\amdpcom64.dll, 8.14.0010.0023 (English), 12/6/2011 02:10:48, 54784 bytes
       Driver: C:\Windows\system32\atimpc64.dll, 8.14.0010.0023 (English), 12/6/2011 02:10:48, 54784 bytes
       Driver: C:\Windows\system32\atiadlxx.dll, 6.14.0010.1089 (English), 12/6/2011 02:13:02, 509952 bytes
       Driver: C:\Windows\system32\atiumd6a.cap, 12/6/2011 02:35:10, 2095328 bytes
       Driver: C:\Windows\system32\atimuixx.dll, 6.14.0010.1002 (English), 12/6/2011 03:09:56, 21504 bytes
       Driver: C:\Windows\system32\atiapfxx.exe, 6.14.0010.1001 (English), 12/6/2011 03:17:50, 159744 bytes
       Driver: C:\Windows\system32\atiapfxx.blb, 12/6/2011 03:18:28, 219080 bytes
       Driver: C:\Windows\system32\atiumd6v.dll, 7.14.0010.0184 (English), 12/6/2011 02:39:58, 1113088 bytes
       Driver: C:\Windows\system32\ativvsva.dat, 12/6/2011 02:35:10, 157152 bytes
       Driver: C:\Windows\system32\ativvsvl.dat, 12/6/2011 02:35:10, 204960 bytes
       Driver: C:\Windows\system32\atiesrxx.exe, 6.14.0011.1114 (English), 12/6/2011 03:11:56, 235520 bytes
       Driver: C:\Windows\system32\atieclxx.exe, 6.14.0011.1114 (English), 12/6/2011 03:12:36, 494080 bytes
       Driver: C:\Windows\system32\atipdl64.dll, 6.14.0010.2563 (English), 12/6/2011 03:10:20, 423424 bytes
       Driver: C:\Windows\system32\atiedu64.dll, 6.14.0010.2514 (English), 12/6/2011 03:09:50, 59392 bytes
       Driver: C:\Windows\system32\ATIDEMGX.dll, 2.00.4356.39985 (English), 12/6/2011 03:12:52, 466944 bytes
       Driver: C:\Windows\system32\atio6axx.dll, 6.14.0010.11399 (English), 12/6/2011 03:18:38, 25371136 bytes
       Driver: C:\Windows\system32\aticaldd64.dll, 6.14.0010.1664 (English), 12/6/2011 02:34:00, 13738496 bytes
       Driver: C:\Windows\system32\aticalrt64.dll, 6.14.0010.1664 (English), 12/6/2011 02:34:28, 51200 bytes
       Driver: C:\Windows\system32\aticalcl64.dll, 6.14.0010.1664 (English), 12/6/2011 02:34:16, 44544 bytes
       Driver: C:\Windows\system32\atipblag.dat, 9/12/2011 23:06:16, 3917 bytes
       Driver: C:\Windows\system32\atiu9p64.dll, 8.14.0001.6248 (English), 12/6/2011 02:11:10, 39936 bytes
       Driver: C:\Windows\system32\atiuxp64.dll, 8.14.0001.6248 (English), 12/6/2011 02:11:24, 42496 bytes
       Driver: C:\Windows\system32\atig6pxx.dll, 8.14.0001.6248 (English), 12/6/2011 02:12:38, 17408 bytes
       Driver: C:\Windows\system32\atig6txx.dll, 8.14.0001.6248 (English), 12/6/2011 02:12:30, 39936 bytes
       Driver: C:\Windows\system32\atibtmon.exe, 2.00.0000.0000 (English), 5/11/2009 22:35:28, 118784 bytes
       Driver: C:\Windows\system32\atidxx64.dll, 8.17.0010.0414 (English), 12/6/2011 02:51:22, 7520768 bytes
       Driver: C:\Windows\SysWOW64\atiumdag.dll, 7.14.0010.0887 (English), 12/6/2011 02:33:36, 5919232 bytes
       Driver: C:\Windows\SysWOW64\atiumdva.dll, 8.14.0010.0342 (English), 12/6/2011 02:28:50, 4206592 bytes
       Driver: C:\Windows\SysWOW64\amdpcom32.dll, 8.14.0010.0023 (English), 12/6/2011 02:10:42, 53760 bytes
       Driver: C:\Windows\SysWOW64\atimpc32.dll, 8.14.0010.0023 (English), 12/6/2011 02:10:42, 53760 bytes
       Driver: C:\Windows\SysWOW64\atiadlxy.dll, 6.14.0010.1089 (English), 12/6/2011 02:12:52, 356352 bytes
       Driver: C:\Windows\SysWOW64\atiumdva.cap, 12/6/2011 02:27:36, 2097056 bytes
       Driver: C:\Windows\SysWOW64\atiumdmv.dll, 7.14.0010.0184 (English), 12/6/2011 02:39:24, 1828864 bytes
       Driver: C:\Windows\SysWOW64\atiapfxx.blb, 12/6/2011 03:18:28, 219080 bytes
       Driver: C:\Windows\SysWOW64\ativvsva.dat, 12/6/2011 02:35:10, 157152 bytes
       Driver: C:\Windows\SysWOW64\ativvsvl.dat, 12/6/2011 02:35:10, 204960 bytes
       Driver: C:\Windows\SysWOW64\atipdlxx.dll, 6.14.0010.2563 (English), 12/6/2011 03:10:12, 360448 bytes
       Driver: C:\Windows\SysWOW64\Oemdspif.dll, 6.15.0006.0006 (English), 12/6/2011 03:10:00, 278528 bytes
       Driver: C:\Windows\SysWOW64\ati2edxx.dll, 6.14.0010.2514 (English), 12/6/2011 03:09:44, 43520 bytes
       Driver: C:\Windows\SysWOW64\atioglxx.dll, 6.14.0010.11399 (English), 12/6/2011 02:56:40, 19125760 bytes
       Driver: C:\Windows\SysWOW64\atidxx32.dll, 8.17.0010.0414 (English), 12/6/2011 03:06:38, 6159872 bytes
       Driver: C:\Windows\SysWOW64\aticaldd.dll, 6.14.0010.1664 (English), 12/6/2011 02:29:30, 11484672 bytes
       Driver: C:\Windows\SysWOW64\aticalrt.dll, 6.14.0010.1664 (English), 12/6/2011 02:34:24, 46080 bytes
       Driver: C:\Windows\SysWOW64\aticalcl.dll, 6.14.0010.1664 (English), 12/6/2011 02:34:14, 44032 bytes
       Driver: C:\Windows\SysWOW64\atipblag.dat, 9/12/2011 23:06:16, 3917 bytes
       Driver: C:\Windows\SysWOW64\atiu9pag.dll, 8.14.0001.6248 (English), 12/6/2011 02:11:02, 29696 bytes
       Driver: C:\Windows\SysWOW64\atiuxpag.dll, 8.14.0001.6248 (English), 12/6/2011 02:11:16, 33280 bytes
       Driver: C:\Windows\SysWOW64\atigktxx.dll, 8.14.0001.6248 (English), 12/6/2011 02:12:22, 33280 bytes
       Driver: C:\Windows\SysWOW64\atiglpxx.dll, 8.14.0001.6248 (English), 12/6/2011 02:12:34, 14336 bytes
       Driver: C:\Windows\atiogl.xml, 10/10/2011 17:51:12, 36338 bytes
       Driver: C:\Windows\system32\ATIODCLI.exe, 1.00.0000.0001 (English), 6/22/2009 16:34:36, 51200 bytes
       Driver: C:\Windows\system32\ATIODE.exe, 1.00.0000.0001 (English), 8/27/2010 19:33:08, 332800 bytes
       Driver: C:\Windows\system32\atiglpxx.dll, 8.14.0001.6248 (English), 12/6/2011 02:12:34, 14336 bytes
       Driver: C:\Windows\system32\aticfx64.dll, 8.17.0010.1114 (English), 12/6/2011 03:16:00, 933888 bytes
       Driver: C:\Windows\SysWOW64\aticfx32.dll, 8.17.0010.1114 (English), 12/6/2011 03:17:36, 778752 bytes
       Driver: C:\Windows\system32\coinst.dll, 1.00.0003.0005 (English), 12/6/2011 02:18:46, 58880 bytes
         Name: Standard Enhanced PCI to USB Host Controller
    Device ID: PCI\VEN_1002&DEV_4396&SUBSYS_84431043&REV_00\3&267A616A&0&9A
       Driver: C:\Windows\system32\drivers\usbehci.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:04, 52736 bytes
       Driver: C:\Windows\system32\drivers\usbport.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:14, 325120 bytes
       Driver: C:\Windows\system32\drivers\usbhub.sys, 6.01.7601.17586 (English), 3/25/2011 03:29:26, 343040 bytes
    DirectShow Filters
    DirectShow Filters:
    WMAudio Decoder DMO,0x00800800,1,1,WMADMOD.DLL,6.01.7601.17514
    WMAPro over S/PDIF DMO,0x00600800,1,1,WMADMOD.DLL,6.01.7601.17514
    WMSpeech Decoder DMO,0x00600800,1,1,WMSPDMOD.DLL,6.01.7601.17514
    MP3 Decoder DMO,0x00600800,1,1,mp3dmod.dll,6.01.7600.16385
    Mpeg4s Decoder DMO,0x00800001,1,1,mp4sdecd.dll,6.01.7600.16385
    WMV Screen decoder DMO,0x00600800,1,1,wmvsdecd.dll,6.01.7601.17514
    WMVideo Decoder DMO,0x00800001,1,1,wmvdecod.dll,6.01.7601.17514
    Mpeg43 Decoder DMO,0x00800001,1,1,mp43decd.dll,6.01.7600.16385
    Mpeg4 Decoder DMO,0x00800001,1,1,mpg4decd.dll,6.01.7600.16385
    DV Muxer,0x00400000,0,0,qdv.dll,6.06.7601.17514
    Color Space Converter,0x00400001,1,1,quartz.dll,6.06.7601.17713
    WM ASF Reader,0x00400000,0,0,qasf.dll,12.00.7601.17514
    Screen Capture filter,0x00200000,0,1,wmpsrcwp.dll,12.00.7601.17514
    AVI Splitter,0x00600000,1,1,quartz.dll,6.06.7601.17713
    VGA 16 Color Ditherer,0x00400000,1,1,quartz.dll,6.06.7601.17713
    SBE2MediaTypeProfile,0x00200000,0,0,sbe.dll,6.06.7601.17528
    Microsoft DTV-DVD Video Decoder,0x005fffff,2,4,msmpeg2vdec.dll,6.01.7140.0000
    AC3 Parser Filter,0x00600000,1,1,mpg2splt.ax,6.06.7601.17528
    StreamBufferSink,0x00200000,0,0,sbe.dll,6.06.7601.17528
    Microsoft TV Captions Decoder,0x00200001,1,0,MSTVCapn.dll,6.01.7601.17715
    MJPEG Decompressor,0x00600000,1,1,quartz.dll,6.06.7601.17713
    CBVA DMO wrapper filter,0x00200000,1,1,cbva.dll,6.01.7601.17514
    MPEG-I Stream Splitter,0x00600000,1,2,quartz.dll,6.06.7601.17713
    SAMI (CC) Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713
    VBI Codec,0x00600000,1,4,VBICodec.ax,6.06.7601.17514
    ATI MPEG File Writer,0x00200000,1,0,atimpenc64.dll,11.06.0000.10126
    ATI MPEG Video Decoder,0x005fffff,1,2,atimpenc64.dll,11.06.0000.10126
    MPEG-2 Splitter,0x005fffff,1,0,mpg2splt.ax,6.06.7601.17528
    Closed Captions Analysis Filter,0x00200000,2,5,cca.dll,6.06.7601.17514
    SBE2FileScan,0x00200000,0,0,sbe.dll,6.06.7601.17528
    Microsoft MPEG-2 Video Encoder,0x00200000,1,1,msmpeg2enc.dll,6.01.7601.17514
    Internal Script Command Renderer,0x00800001,1,0,quartz.dll,6.06.7601.17713
    MPEG Audio Decoder,0x03680001,1,1,quartz.dll,6.06.7601.17713
    DV Splitter,0x00600000,1,2,qdv.dll,6.06.7601.17514
    Video Mixing Renderer 9,0x00200000,1,0,quartz.dll,6.06.7601.17713
    Microsoft MPEG-2 Encoder,0x00200000,2,1,msmpeg2enc.dll,6.01.7601.17514
    ATI MPEG Audio Encoder,0x00200000,1,1,atimpenc64.dll,11.06.0000.10126
    ACM Wrapper,0x00600000,1,1,quartz.dll,6.06.7601.17713
    Video Renderer,0x00800001,1,0,quartz.dll,6.06.7601.17713
    MPEG-2 Video Stream Analyzer,0x00200000,0,0,sbe.dll,6.06.7601.17528
    Line 21 Decoder,0x00600000,1,1,,
    Video Port Manager,0x00600000,2,1,quartz.dll,6.06.7601.17713
    Video Renderer,0x00400000,1,0,quartz.dll,6.06.7601.17713
    ATI MPEG Video Encoder,0x00200000,1,1,atimpenc64.dll,11.06.0000.10126
    ATI MPEG Multiplexer,0x00200000,2,1,atimpenc64.dll,11.06.0000.10126
    VPS Decoder,0x00200000,0,0,WSTPager.ax,6.06.7601.17514
    WM ASF Writer,0x00400000,0,0,qasf.dll,12.00.7601.17514
    VBI Surface Allocator,0x00600000,1,1,vbisurf.ax,6.01.7601.17514
    File writer,0x00200000,1,0,qcap.dll,6.06.7601.17514
    iTV Data Sink,0x00600000,1,0,itvdata.dll,6.06.7601.17514
    iTV Data Capture filter,0x00600000,1,1,itvdata.dll,6.06.7601.17514
    ATI Video Scaler Filter,0x00200000,1,1,atimpenc64.dll,11.06.0000.10126
    DVD Navigator,0x00200000,0,3,qdvd.dll,6.06.7601.17713
    Microsoft TV Subtitles Decoder,0x00200001,1,0,MSTVCapn.dll,6.01.7601.17715
    Overlay Mixer2,0x00200000,1,1,,
    RDP DShow Redirection Filter,0xffffffff,1,0,DShowRdpFilter.dll,
    Microsoft MPEG-2 Audio Encoder,0x00200000,1,1,msmpeg2enc.dll,6.01.7601.17514
    WST Pager,0x00200000,1,1,WSTPager.ax,6.06.7601.17514
    MPEG-2 Demultiplexer,0x00600000,1,1,mpg2splt.ax,6.06.7601.17528
    DV Video Decoder,0x00800000,1,1,qdv.dll,6.06.7601.17514
    SampleGrabber,0x00200000,1,1,qedit.dll,6.06.7601.17514
    Null Renderer,0x00200000,1,0,qedit.dll,6.06.7601.17514
    MPEG-2 Sections and Tables,0x005fffff,1,0,Mpeg2Data.ax,6.06.7601.17514
    Microsoft AC3 Encoder,0x00200000,1,1,msac3enc.dll,6.01.7601.17514
    StreamBufferSource,0x00200000,0,0,sbe.dll,6.06.7601.17528
    Smart Tee,0x00200000,1,2,qcap.dll,6.06.7601.17514
    Overlay Mixer,0x00200000,0,0,,
    AVI Decompressor,0x00600000,1,1,quartz.dll,6.06.7601.17713
    NetBridge,0x00200000,2,0,netbridge.dll,6.01.7601.17514
    AVI/WAV File Source,0x00400000,0,2,quartz.dll,6.06.7601.17713
    Wave Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713
    MIDI Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713
    Multi-file Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713
    File stream renderer,0x00400000,1,1,quartz.dll,6.06.7601.17713
    ATI Video Rotation Filter,0x00200000,1,1,atimpenc64.dll,11.06.0000.10126
    Microsoft DTV-DVD Audio Decoder,0x005fffff,1,1,msmpeg2adec.dll,6.01.7140.0000
    StreamBufferSink2,0x00200000,0,0,sbe.dll,6.06.7601.17528
    AVI Mux,0x00200000,1,0,qcap.dll,6.06.7601.17514
    Line 21 Decoder 2,0x00600002,1,1,quartz.dll,6.06.7601.17713
    File Source (Async.),0x00400000,0,1,quartz.dll,6.06.7601.17713
    File Source (URL),0x00400000,0,1,quartz.dll,6.06.7601.17713
    Media Center Extender Encryption Filter,0x00200000,2,2,Mcx2Filter.dll,6.01.7601.17514
    AudioRecorder WAV Dest,0x00200000,0,0,WavDest.dll,
    AudioRecorder Wave Form,0x00200000,0,0,WavDest.dll,
    SoundRecorder Null Renderer,0x00200000,0,0,WavDest.dll,
    Infinite Pin Tee Filter,0x00200000,1,1,qcap.dll,6.06.7601.17514
    Enhanced Video Renderer,0x00200000,1,0,evr.dll,6.01.7601.17514
    BDA MPEG2 Transport Information Filter,0x00200000,2,0,psisrndr.ax,6.06.7601.17669
    MPEG Video Decoder,0x40000001,1,1,quartz.dll,6.06.7601.17713
    WDM Streaming Tee/Splitter Devices:
    Tee/Sink-to-Sink Converter,0x00200000,1,1,ksproxy.ax,6.01.7601.17514
    Video Compressors:
    WMVideo8 Encoder DMO,0x00600800,1,1,wmvxencd.dll,6.01.7600.16385
    WMVideo9 Encoder DMO,0x00600800,1,1,wmvencod.dll,6.01.7600.16385
    MSScreen 9 encoder DMO,0x00600800,1,1,wmvsencd.dll,6.01.7600.16385
    DV Video Encoder,0x00200000,0,0,qdv.dll,6.06.7601.17514
    MJPEG Compressor,0x00200000,0,0,quartz.dll,6.06.7601.17713

    Quote from: Svet on 16-February-12, 02:36:34
    driver crashes means BSOD? if yes, this hapends during what?
    have you tried to load BIOS optimized defaults?
    do you use MSI vga drivers for your video card?
    is your computer stable if you use another video card?
    To answer in order:
    No BSOD, the display locks up, audio continues to play, both screens flash to blank black then the UI returns and windows 7 reports "Display driver amdkmdap stopped responding and has successfully recovered."
    I have not loaded BIOS optimized defaults that i am aware of.
    I am currently using ATI drivers sourced from the ATI site.
    Machine is stable when using integrated GFX or an Nvidia 470GTX (with corresponding drivers).

  • Optimizing system for best performance/stability and a custom kernel

    I have ArchLinux running on a MacBook 4.1 (early 2008), and it's running very well so far. But I would like to optimize it for best performance and stability (but not at the cost of losing 'graphical interface' quality). I want to compile a custom kernel, and I actually did once, but didn't do it well (and removed it), so I need some help from experts to tell me what should I disable or enable when compiling a custom kernel.
    I will post dmesg and lspci (and rc.conf) here, but if you need any other information, please tell me.
    Thanks.
    Dmesg:
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Linux version 3.4.4-2-ARCH (tobias@T-POWA-LX) (gcc version 4.7.1 (GCC) ) #1 SMP PREEMPT Sun Jun 24 18:59:47 CEST 2012
    [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=98afbd56-6ae5-415e-9710-73b8b4ba946c ro quiet add_efi_memmap loglevel=3 console=tty1 splash=silent,fadein,fadeout,theme:arch-banner-icons
    [ 0.000000] BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    [ 0.000000] BIOS-e820: 0000000000100000 - 000000007dd31000 (usable)
    [ 0.000000] BIOS-e820: 000000007dd31000 - 000000007df32000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 000000007df32000 - 000000007dfe5000 (ACPI data)
    [ 0.000000] BIOS-e820: 000000007dfe5000 - 000000007dfe7000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 000000007dfe7000 - 000000007eec3000 (ACPI data)
    [ 0.000000] BIOS-e820: 000000007eec3000 - 000000007eec5000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 000000007eec5000 - 000000007eec8000 (ACPI data)
    [ 0.000000] BIOS-e820: 000000007eec8000 - 000000007eecb000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 000000007eecb000 - 000000007eecc000 (ACPI data)
    [ 0.000000] BIOS-e820: 000000007eecc000 - 000000007eedf000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 000000007eedf000 - 000000007eef9000 (ACPI data)
    [ 0.000000] BIOS-e820: 000000007eef9000 - 000000007eeff000 (reserved)
    [ 0.000000] BIOS-e820: 000000007eeff000 - 000000007ef00000 (ACPI data)
    [ 0.000000] BIOS-e820: 000000007ef00000 - 0000000080000000 (reserved)
    [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] DMI 2.4 present.
    [ 0.000000] DMI: Apple Inc. MacBook4,1/Mac-F22788A9, BIOS MB41.88Z.00C1.B00.0802091535 02/09/08
    [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    [ 0.000000] No AGP bridge found
    [ 0.000000] last_pfn = 0x7dd31 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-CFFFF write-protect
    [ 0.000000] D0000-DFFFF uncachable
    [ 0.000000] E0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 0FFE00000 mask FFFE00000 write-protect
    [ 0.000000] 1 base 000000000 mask F80000000 write-back
    [ 0.000000] 2 base 07F000000 mask FFF000000 uncachable
    [ 0.000000] 3 base 07EF00000 mask FFFF00000 uncachable
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] initial memory mapped : 0 - 20000000
    [ 0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
    [ 0.000000] init_memory_mapping: 0000000000000000-000000007dd31000
    [ 0.000000] 0000000000 - 007dc00000 page 2M
    [ 0.000000] 007dc00000 - 007dd31000 page 4k
    [ 0.000000] kernel direct mapping tables up to 7dd31000 @ 1fffc000-20000000
    [ 0.000000] RAMDISK: 37492000 - 37a41000
    [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 APPLE )
    [ 0.000000] ACPI: XSDT 000000007eeee1c0 00084 (v01 APPLE Apple00 000000C1 01000013)
    [ 0.000000] ACPI: FACP 000000007eeec000 000F4 (v03 APPLE Apple00 000000C1 Loki 0000005F)
    [ 0.000000] ACPI: DSDT 000000007eee1000 045C6 (v01 APPLE MacBook 00040001 INTL 20061109)
    [ 0.000000] ACPI: FACS 000000007eecc000 00040
    [ 0.000000] ACPI: HPET 000000007eeeb000 00038 (v01 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: APIC 000000007eeea000 00068 (v01 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: MCFG 000000007eee9000 0003C (v01 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: ASF! 000000007eee8000 000A5 (v32 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: SBST 000000007eee7000 00030 (v01 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: ECDT 000000007eee6000 00053 (v01 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: SSDT 000000007eec7000 004DC (v01 APPLE CpuPm 00003000 INTL 20061109)
    [ 0.000000] ACPI: SSDT 000000007eec6000 0025F (v01 APPLE Cpu0Tst 00003000 INTL 20061109)
    [ 0.000000] ACPI: SSDT 000000007eec5000 000A6 (v01 APPLE Cpu1Tst 00003000 INTL 20061109)
    [ 0.000000] ACPI: SSDT 000000007eee0000 00544 (v01 SataRe SataPri 00001000 INTL 20061109)
    [ 0.000000] ACPI: SSDT 000000007eedf000 00477 (v01 SataRe SataSec 00001000 INTL 20061109)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at 0000000000000000-000000007dd31000
    [ 0.000000] Initmem setup node 0 0000000000000000-000000007dd31000
    [ 0.000000] NODE_DATA [000000007dd2d000 - 000000007dd30fff]
    [ 0.000000] [ffffea0000000000-ffffea0001ffffff] PMD -> [ffff88007b400000-ffff88007d3fffff] on node 0
    [ 0.000000] Zone PFN ranges:
    [ 0.000000] DMA 0x00000010 -> 0x00001000
    [ 0.000000] DMA32 0x00001000 -> 0x00100000
    [ 0.000000] Normal empty
    [ 0.000000] Movable zone start PFN for each node
    [ 0.000000] Early memory PFN ranges
    [ 0.000000] 0: 0x00000010 -> 0x0000009f
    [ 0.000000] 0: 0x00000100 -> 0x0007dd31
    [ 0.000000] On node 0 totalpages: 515264
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 5 pages reserved
    [ 0.000000] DMA zone: 3914 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 7989 pages used for memmap
    [ 0.000000] DMA32 zone: 503292 pages, LIFO batch:31
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
    [ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:70000000)
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:2 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88007da00000 s82880 r8192 d23616 u1048576
    [ 0.000000] pcpu-alloc: s82880 r8192 d23616 u1048576 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 507206
    [ 0.000000] Policy zone: DMA32
    [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=98afbd56-6ae5-415e-9710-73b8b4ba946c ro quiet add_efi_memmap loglevel=3 console=tty1 splash=silent,fadein,fadeout,theme:arch-banner-icons
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] Checking aperture...
    [ 0.000000] No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 2011044k/2061508k available (4538k kernel code, 452k absent, 50012k reserved, 4308k data, 740k init)
    [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] NR_IRQS:4352 nr_irqs:512 16
    [ 0.000000] Extended CMOS year: 2000
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty1] enabled
    [ 0.000000] allocated 8388608 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] Fast TSC calibration failed
    [ 0.000000] TSC: PIT calibration matches HPET. 2 loops
    [ 0.000000] Detected 2393.995 MHz processor.
    [ 0.010005] Calibrating delay loop (skipped), value calculated using timer frequency.. 4789.48 BogoMIPS (lpj=7979983)
    [ 0.010013] pid_max: default: 32768 minimum: 301
    [ 0.010061] Security Framework initialized
    [ 0.010069] AppArmor: AppArmor disabled by boot time parameter
    [ 0.010381] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.011643] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.012201] Mount-cache hash table entries: 256
    [ 0.012567] Initializing cgroup subsys cpuacct
    [ 0.012573] Initializing cgroup subsys memory
    [ 0.012588] Initializing cgroup subsys devices
    [ 0.012592] Initializing cgroup subsys freezer
    [ 0.012595] Initializing cgroup subsys net_cls
    [ 0.012599] Initializing cgroup subsys blkio
    [ 0.012653] CPU: Physical Processor ID: 0
    [ 0.012656] CPU: Processor Core ID: 0
    [ 0.012660] mce: CPU supports 6 MCE banks
    [ 0.012673] CPU0: Thermal monitoring enabled (TM2)
    [ 0.012679] using mwait in idle threads.
    [ 0.015816] ACPI: Core revision 20120320
    [ 0.021231] ftrace: allocating 17820 entries in 70 pages
    [ 0.030546] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.064790] CPU0: Intel(R) Core(TM)2 Duo CPU T8300 @ 2.40GHz stepping 06
    [ 0.066663] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
    [ 0.066663] ... version: 2
    [ 0.066663] ... bit width: 40
    [ 0.066663] ... generic registers: 2
    [ 0.066663] ... value mask: 000000ffffffffff
    [ 0.066663] ... max period: 000000007fffffff
    [ 0.066663] ... fixed-purpose events: 3
    [ 0.066663] ... event mask: 0000000700000003
    [ 0.083458] NMI watchdog: enabled, takes one hw-pmu counter.
    [ 0.103350] Booting Node 0, Processors #1 Ok.
    [ 0.116508] NMI watchdog: enabled, takes one hw-pmu counter.
    [ 0.116575] Brought up 2 CPUs
    [ 0.116579] Total of 2 processors activated (9579.97 BogoMIPS).
    [ 0.120053] devtmpfs: initialized
    [ 0.122018] PM: Registering ACPI NVS region [mem 0x7dd31000-0x7df31fff] (2101248 bytes)
    [ 0.122018] PM: Registering ACPI NVS region [mem 0x7dfe5000-0x7dfe6fff] (8192 bytes)
    [ 0.122018] PM: Registering ACPI NVS region [mem 0x7eec3000-0x7eec4fff] (8192 bytes)
    [ 0.122018] PM: Registering ACPI NVS region [mem 0x7eec8000-0x7eecafff] (12288 bytes)
    [ 0.122018] PM: Registering ACPI NVS region [mem 0x7eecc000-0x7eedefff] (77824 bytes)
    [ 0.123629] NET: Registered protocol family 16
    [ 0.123872] ACPI: bus type pci registered
    [ 0.123988] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xf0000000-0xffffffff] (base 0xf0000000)
    [ 0.123995] PCI: MMCONFIG at [mem 0xf0000000-0xffffffff] reserved in E820
    [ 0.124001] PCI: MMCONFIG for 0000 [bus00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000) (size reduced!)
    [ 0.153700] PCI: Using configuration type 1 for base access
    [ 0.153895] mtrr: your CPUs had inconsistent variable MTRR settings
    [ 0.153899] mtrr: probably your BIOS does not setup all CPUs.
    [ 0.153901] mtrr: corrected configuration.
    [ 0.154568] bio: create slab <bio-0> at 0
    [ 0.154568] ACPI: Added _OSI(Module Device)
    [ 0.154568] ACPI: Added _OSI(Processor Device)
    [ 0.154568] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.154568] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.154919] ACPI: EC: EC description table is found, configuring boot EC
    [ 0.159179] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
    [ 0.160245] ACPI: SSDT 000000007eecaa98 00340 (v01 APPLE Cpu0Ist 00003000 INTL 20061109)
    [ 0.160625] ACPI: Dynamic OEM Table Load:
    [ 0.160630] ACPI: SSDT (null) 00340 (v01 APPLE Cpu0Ist 00003000 INTL 20061109)
    [ 0.160795] ACPI: SSDT 000000007eec8c18 002AD (v01 APPLE Cpu0Cst 00003001 INTL 20061109)
    [ 0.161153] ACPI: Dynamic OEM Table Load:
    [ 0.161158] ACPI: SSDT (null) 002AD (v01 APPLE Cpu0Cst 00003001 INTL 20061109)
    [ 0.161186] ACPI: SSDT 000000007eec9f18 000C8 (v01 APPLE Cpu1Ist 00003000 INTL 20061109)
    [ 0.161186] ACPI: Dynamic OEM Table Load:
    [ 0.161186] ACPI: SSDT (null) 000C8 (v01 APPLE Cpu1Ist 00003000 INTL 20061109)
    [ 0.161186] ACPI: SSDT 000000007eec8f18 00085 (v01 APPLE Cpu1Cst 00003000 INTL 20061109)
    [ 0.161187] ACPI: Dynamic OEM Table Load:
    [ 0.161192] ACPI: SSDT (null) 00085 (v01 APPLE Cpu1Cst 00003000 INTL 20061109)
    [ 0.161220] ACPI: Interpreter enabled
    [ 0.161220] ACPI: (supports S0 S3 S4 S5)
    [ 0.161220] ACPI: Using IOAPIC for interrupt routing
    [ 0.173742] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
    [ 0.173981] ACPI: No dock devices found.
    [ 0.173988] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.174581] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.175426] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
    [ 0.175431] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
    [ 0.175436] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
    [ 0.175443] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xfebfffff]
    [ 0.175505] PCI host bridge to bus 0000:00
    [ 0.175510] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.175514] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.175518] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.175523] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff]
    [ 0.175539] pci 0000:00:00.0: [8086:2a00] type 00 class 0x060000
    [ 0.175610] pci 0000:00:02.0: [8086:2a02] type 00 class 0x030000
    [ 0.175631] pci 0000:00:02.0: reg 10: [mem 0x90100000-0x901fffff 64bit]
    [ 0.175645] pci 0000:00:02.0: reg 18: [mem 0x80000000-0x8fffffff 64bit pref]
    [ 0.175655] pci 0000:00:02.0: reg 20: [io 0x6110-0x6117]
    [ 0.175712] pci 0000:00:02.1: [8086:2a03] type 00 class 0x038000
    [ 0.175730] pci 0000:00:02.1: reg 10: [mem 0x90200000-0x902fffff 64bit]
    [ 0.175849] pci 0000:00:1a.0: [8086:2834] type 00 class 0x0c0300
    [ 0.175917] pci 0000:00:1a.0: reg 20: [io 0x60c0-0x60df]
    [ 0.175971] pci 0000:00:1a.1: [8086:2835] type 00 class 0x0c0300
    [ 0.176038] pci 0000:00:1a.1: reg 20: [io 0x60a0-0x60bf]
    [ 0.176110] pci 0000:00:1a.7: [8086:283a] type 00 class 0x0c0320
    [ 0.176140] pci 0000:00:1a.7: reg 10: [mem 0x90704c00-0x90704fff]
    [ 0.176140] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
    [ 0.176140] pci 0000:00:1b.0: [8086:284b] type 00 class 0x040300
    [ 0.176140] pci 0000:00:1b.0: reg 10: [mem 0x90700000-0x90703fff 64bit]
    [ 0.176140] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.176140] pci 0000:00:1c.0: [8086:283f] type 01 class 0x060400
    [ 0.176140] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.176140] pci 0000:00:1c.4: [8086:2847] type 01 class 0x060400
    [ 0.176140] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
    [ 0.176140] pci 0000:00:1c.5: [8086:2849] type 01 class 0x060400
    [ 0.176140] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
    [ 0.176140] pci 0000:00:1d.0: [8086:2830] type 00 class 0x0c0300
    [ 0.176140] pci 0000:00:1d.0: reg 20: [io 0x6080-0x609f]
    [ 0.176140] pci 0000:00:1d.1: [8086:2831] type 00 class 0x0c0300
    [ 0.176140] pci 0000:00:1d.1: reg 20: [io 0x6060-0x607f]
    [ 0.176140] pci 0000:00:1d.2: [8086:2832] type 00 class 0x0c0300
    [ 0.176140] pci 0000:00:1d.2: reg 20: [io 0x6040-0x605f]
    [ 0.176140] pci 0000:00:1d.7: [8086:2836] type 00 class 0x0c0320
    [ 0.176140] pci 0000:00:1d.7: reg 10: [mem 0x90704800-0x90704bff]
    [ 0.176140] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.176140] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
    [ 0.176140] pci 0000:00:1f.0: [8086:2815] type 00 class 0x060100
    [ 0.176140] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 000f)
    [ 0.176140] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 1640 (mask 000f)
    [ 0.176140] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0300 (mask 001f)
    [ 0.176140] pci 0000:00:1f.1: [8086:2850] type 00 class 0x01018f
    [ 0.176140] pci 0000:00:1f.1: reg 10: [io 0x6108-0x610f]
    [ 0.176140] pci 0000:00:1f.1: reg 14: [io 0x6124-0x6127]
    [ 0.176140] pci 0000:00:1f.1: reg 18: [io 0x6100-0x6107]
    [ 0.176140] pci 0000:00:1f.1: reg 1c: [io 0x6120-0x6123]
    [ 0.176140] pci 0000:00:1f.1: reg 20: [io 0x60e0-0x60ef]
    [ 0.176140] pci 0000:00:1f.2: [8086:2828] type 00 class 0x01018f
    [ 0.176140] pci 0000:00:1f.2: reg 10: [io 0x60f8-0x60ff]
    [ 0.176140] pci 0000:00:1f.2: reg 14: [io 0x611c-0x611f]
    [ 0.176140] pci 0000:00:1f.2: reg 18: [io 0x60f0-0x60f7]
    [ 0.176140] pci 0000:00:1f.2: reg 1c: [io 0x6118-0x611b]
    [ 0.176140] pci 0000:00:1f.2: reg 20: [io 0x6020-0x602f]
    [ 0.176140] pci 0000:00:1f.2: reg 24: [io 0x4000-0x400f]
    [ 0.176140] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.176140] pci 0000:00:1f.3: [8086:283e] type 00 class 0x0c0500
    [ 0.176140] pci 0000:00:1f.3: reg 10: [mem 0x90705000-0x907050ff]
    [ 0.176140] pci 0000:00:1f.3: reg 20: [io 0xefa0-0xefbf]
    [ 0.176140] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
    [ 0.176140] pci 0000:00:1c.0: bridge window [mem 0x90600000-0x906fffff]
    [ 0.176140] pci 0000:02:00.0: [14e4:4328] type 00 class 0x028000
    [ 0.176140] pci 0000:02:00.0: reg 10: [mem 0x90500000-0x90503fff 64bit]
    [ 0.176140] pci 0000:02:00.0: reg 18: [mem 0x90000000-0x900fffff 64bit pref]
    [ 0.176140] pci 0000:02:00.0: supports D1 D2
    [ 0.176140] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
    [ 0.183347] pci 0000:00:1c.4: PCI bridge to [bus 02-02]
    [ 0.183358] pci 0000:00:1c.4: bridge window [mem 0x90500000-0x905fffff]
    [ 0.183369] pci 0000:00:1c.4: bridge window [mem 0x90000000-0x900fffff 64bit pref]
    [ 0.183595] pci 0000:03:00.0: [11ab:436a] type 00 class 0x020000
    [ 0.183741] pci 0000:03:00.0: reg 10: [mem 0x90400000-0x90403fff 64bit]
    [ 0.183826] pci 0000:03:00.0: reg 18: [io 0x5000-0x50ff]
    [ 0.184121] pci 0000:03:00.0: reg 30: [mem 0xfffe0000-0xffffffff pref]
    [ 0.184581] pci 0000:03:00.0: supports D1 D2
    [ 0.184585] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.184821] pci 0000:00:1c.5: PCI bridge to [bus 03-03]
    [ 0.184828] pci 0000:00:1c.5: bridge window [io 0x5000-0x5fff]
    [ 0.184836] pci 0000:00:1c.5: bridge window [mem 0x90400000-0x904fffff]
    [ 0.184905] pci 0000:04:03.0: [11c1:5811] type 00 class 0x0c0010
    [ 0.184934] pci 0000:04:03.0: reg 10: [mem 0x90300000-0x90300fff]
    [ 0.185056] pci 0000:04:03.0: supports D1 D2
    [ 0.185060] pci 0000:04:03.0: PME# supported from D0 D1 D2 D3hot
    [ 0.185137] pci 0000:00:1e.0: PCI bridge to [bus 04-04] (subtractive decode)
    [ 0.185148] pci 0000:00:1e.0: bridge window [mem 0x90300000-0x903fffff]
    [ 0.185160] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.185165] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.185169] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.185174] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
    [ 0.185211] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.185419] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
    [ 0.185489] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
    [ 0.185588] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
    [ 0.185829] pci0000:00: Requesting ACPI _OSC control (0x1d)
    [ 0.186233] pci0000:00: ACPI _OSC control (0x1d) granted
    [ 0.193405] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
    [ 0.193487] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 *7 11 12 14 15)
    [ 0.193565] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 12 14 15)
    [ 0.193642] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
    [ 0.193720] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
    [ 0.193797] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *9
    [ 0.193874] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
    [ 0.193957] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
    [ 0.196686] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.196707] vgaarb: loaded
    [ 0.196709] vgaarb: bridge control possible 0000:00:02.0
    [ 0.196788] PCI: Using ACPI for IRQ routing
    [ 0.197237] PCI: pci_cache_line_size set to 64 bytes
    [ 0.197407] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
    [ 0.197411] reserve RAM buffer: 000000007dd31000 - 000000007fffffff
    [ 0.197573] NetLabel: Initializing
    [ 0.197576] NetLabel: domain hash size = 128
    [ 0.197579] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.197601] NetLabel: unlabeled traffic allowed by default
    [ 0.197632] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    [ 0.197640] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.197648] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    [ 0.210013] Switching to clocksource hpet
    [ 0.222129] pnp: PnP ACPI init
    [ 0.222158] ACPI: bus type pnp registered
    [ 0.222675] pnp 00:00: [bus 00-ff]
    [ 0.222680] pnp 00:00: [io 0x0000-0x0cf7 window]
    [ 0.222684] pnp 00:00: [io 0x0cf8-0x0cff]
    [ 0.222688] pnp 00:00: [io 0x0d00-0xffff window]
    [ 0.222692] pnp 00:00: [mem 0x000a0000-0x000bffff window]
    [ 0.222696] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
    [ 0.222700] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
    [ 0.222703] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
    [ 0.222707] pnp 00:00: [mem 0x000cc000-0x000cffff window]
    [ 0.222711] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
    [ 0.222715] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
    [ 0.222718] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
    [ 0.222723] pnp 00:00: [mem 0x000dc000-0x000dffff window]
    [ 0.222726] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
    [ 0.222735] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
    [ 0.222739] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
    [ 0.222743] pnp 00:00: [mem 0x000ec000-0x000effff window]
    [ 0.222746] pnp 00:00: [mem 0x000f0000-0x000fffff window]
    [ 0.222750] pnp 00:00: [mem 0x80000000-0xfebfffff window]
    [ 0.222859] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
    [ 0.222989] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
    [ 0.222993] pnp 00:01: [mem 0xfed14000-0xfed17fff]
    [ 0.222996] pnp 00:01: [mem 0xfed18000-0xfed18fff]
    [ 0.223000] pnp 00:01: [mem 0xfed19000-0xfed19fff]
    [ 0.223003] pnp 00:01: [mem 0xf0000000-0xf3ffffff]
    [ 0.223006] pnp 00:01: [mem 0xfed20000-0xfed3ffff]
    [ 0.223010] pnp 00:01: [mem 0xfed45000-0xfed8ffff]
    [ 0.223109] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.223115] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
    [ 0.223119] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
    [ 0.223124] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
    [ 0.223129] system 00:01: [mem 0xf0000000-0xf3ffffff] has been reserved
    [ 0.223134] system 00:01: [mem 0xfed20000-0xfed3ffff] has been reserved
    [ 0.223138] system 00:01: [mem 0xfed45000-0xfed8ffff] has been reserved
    [ 0.223145] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.223455] pnp 00:02: [io 0x0300-0x031f]
    [ 0.223473] pnp 00:02: [irq 6]
    [ 0.223541] pnp 00:02: Plug and Play ACPI device, IDs APP0001 (active)
    [ 0.223606] pnp 00:03: [io 0x0000-0x001f]
    [ 0.223610] pnp 00:03: [io 0x0081-0x0091]
    [ 0.223614] pnp 00:03: [io 0x0093-0x009f]
    [ 0.223617] pnp 00:03: [io 0x00c0-0x00df]
    [ 0.223621] pnp 00:03: [dma 4]
    [ 0.223695] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.223710] pnp 00:04: [mem 0xff000000-0xffffffff]
    [ 0.223778] pnp 00:04: Plug and Play ACPI device, IDs INT0800 (active)
    [ 0.223883] pnp 00:05: [irq 0 disabled]
    [ 0.223893] pnp 00:05: [irq 8]
    [ 0.223897] pnp 00:05: [mem 0xfed00000-0xfed003ff]
    [ 0.224002] system 00:05: [mem 0xfed00000-0xfed003ff] has been reserved
    [ 0.224009] system 00:05: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
    [ 0.224028] pnp 00:06: [io 0x00f0]
    [ 0.224038] pnp 00:06: [irq 13]
    [ 0.224112] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.224132] pnp 00:07: [io 0x002e-0x002f]
    [ 0.224136] pnp 00:07: [io 0x004e-0x004f]
    [ 0.224139] pnp 00:07: [io 0x0061]
    [ 0.224142] pnp 00:07: [io 0x0063]
    [ 0.224145] pnp 00:07: [io 0x0065]
    [ 0.224149] pnp 00:07: [io 0x0067]
    [ 0.224151] pnp 00:07: [io 0x0070]
    [ 0.224154] pnp 00:07: [io 0x0080]
    [ 0.224157] pnp 00:07: [io 0x0092]
    [ 0.224161] pnp 00:07: [io 0x00b2-0x00b3]
    [ 0.224164] pnp 00:07: [io 0x0680-0x069f]
    [ 0.224167] pnp 00:07: [io 0x0800-0x080f]
    [ 0.224170] pnp 00:07: [io 0x0810-0x0817]
    [ 0.224173] pnp 00:07: [io 0x0400-0x047f]
    [ 0.224177] pnp 00:07: [io 0x0500-0x053f]
    [ 0.224180] pnp 00:07: [io 0x1640-0x164f]
    [ 0.224302] system 00:07: [io 0x0680-0x069f] has been reserved
    [ 0.224307] system 00:07: [io 0x0800-0x080f] has been reserved
    [ 0.224312] system 00:07: [io 0x0810-0x0817] has been reserved
    [ 0.224316] system 00:07: [io 0x0400-0x047f] has been reserved
    [ 0.224320] system 00:07: [io 0x0500-0x053f] has been reserved
    [ 0.224325] system 00:07: [io 0x1640-0x164f] has been reserved
    [ 0.224331] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.224346] pnp 00:08: [io 0x0070-0x0077]
    [ 0.224417] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.228737] pnp: PnP ACPI: found 9 devices
    [ 0.228741] ACPI: ACPI bus type pnp unregistered
    [ 0.237540] pci 0000:03:00.0: no compatible bridge window for [mem 0xfffe0000-0xffffffff pref]
    [ 0.237582] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01-01] add_size 1000
    [ 0.237590] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01-01] add_size 200000
    [ 0.237607] pci 0000:00:1c.4: bridge window [io 0x1000-0x0fff] to [bus 02-02] add_size 1000
    [ 0.237623] pci 0000:00:1c.5: bridge window [mem 0x00100000-0x001fffff pref] to [bus 03-03] add_size 200000
    [ 0.237646] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 0.237652] pci 0000:00:1c.5: res[15]=[mem 0x00100000-0x001fffff pref] get_res_add_size add_size 200000
    [ 0.237657] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 0.237662] pci 0000:00:1c.4: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 0.237672] pci 0000:00:1c.0: BAR 15: assigned [mem 0x90800000-0x909fffff 64bit pref]
    [ 0.237678] pci 0000:00:1c.5: BAR 15: assigned [mem 0x90a00000-0x90cfffff pref]
    [ 0.237684] pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
    [ 0.237689] pci 0000:00:1c.4: BAR 13: assigned [io 0x3000-0x3fff]
    [ 0.237694] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
    [ 0.237701] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
    [ 0.237710] pci 0000:00:1c.0: bridge window [mem 0x90600000-0x906fffff]
    [ 0.237718] pci 0000:00:1c.0: bridge window [mem 0x90800000-0x909fffff 64bit pref]
    [ 0.237730] pci 0000:00:1c.4: PCI bridge to [bus 02-02]
    [ 0.237736] pci 0000:00:1c.4: bridge window [io 0x3000-0x3fff]
    [ 0.237746] pci 0000:00:1c.4: bridge window [mem 0x90500000-0x905fffff]
    [ 0.237754] pci 0000:00:1c.4: bridge window [mem 0x90000000-0x900fffff 64bit pref]
    [ 0.237767] pci 0000:03:00.0: BAR 6: assigned [mem 0x90a00000-0x90a1ffff pref]
    [ 0.237772] pci 0000:00:1c.5: PCI bridge to [bus 03-03]
    [ 0.237777] pci 0000:00:1c.5: bridge window [io 0x5000-0x5fff]
    [ 0.237787] pci 0000:00:1c.5: bridge window [mem 0x90400000-0x904fffff]
    [ 0.237795] pci 0000:00:1c.5: bridge window [mem 0x90a00000-0x90cfffff pref]
    [ 0.237807] pci 0000:00:1e.0: PCI bridge to [bus 04-04]
    [ 0.237816] pci 0000:00:1e.0: bridge window [mem 0x90300000-0x903fffff]
    [ 0.237837] pci 0000:00:1c.0: enabling device (0000 -> 0003)
    [ 0.237918] pci 0000:00:1e.0: power state changed by ACPI to D0
    [ 0.237925] pci 0000:00:1e.0: power state changed by ACPI to D0
    [ 0.237934] pci 0000:00:1e.0: setting latency timer to 64
    [ 0.237942] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.237946] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.237950] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.237954] pci_bus 0000:00: resource 7 [mem 0x80000000-0xfebfffff]
    [ 0.237959] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
    [ 0.237963] pci_bus 0000:01: resource 1 [mem 0x90600000-0x906fffff]
    [ 0.237967] pci_bus 0000:01: resource 2 [mem 0x90800000-0x909fffff 64bit pref]
    [ 0.237972] pci_bus 0000:02: resource 0 [io 0x3000-0x3fff]
    [ 0.237976] pci_bus 0000:02: resource 1 [mem 0x90500000-0x905fffff]
    [ 0.237980] pci_bus 0000:02: resource 2 [mem 0x90000000-0x900fffff 64bit pref]
    [ 0.237984] pci_bus 0000:03: resource 0 [io 0x5000-0x5fff]
    [ 0.237988] pci_bus 0000:03: resource 1 [mem 0x90400000-0x904fffff]
    [ 0.237992] pci_bus 0000:03: resource 2 [mem 0x90a00000-0x90cfffff pref]
    [ 0.237997] pci_bus 0000:04: resource 1 [mem 0x90300000-0x903fffff]
    [ 0.238001] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
    [ 0.238005] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
    [ 0.238009] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.238013] pci_bus 0000:04: resource 7 [mem 0x80000000-0xfebfffff]
    [ 0.238088] NET: Registered protocol family 2
    [ 0.238250] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
    [ 0.239170] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
    [ 0.241419] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    [ 0.241995] TCP: Hash tables configured (established 262144 bind 65536)
    [ 0.241999] TCP: reno registered
    [ 0.242015] UDP hash table entries: 1024 (order: 3, 32768 bytes)
    [ 0.242042] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
    [ 0.242207] NET: Registered protocol family 1
    [ 0.242239] pci 0000:00:02.0: Boot video device
    [ 0.242578] PCI: CLS mismatch (256 != 64), using 64 bytes
    [ 0.242662] Unpacking initramfs...
    [ 0.452648] Freeing initrd memory: 5820k freed
    [ 0.456693] audit: initializing netlink socket (disabled)
    [ 0.456719] type=2000 audit(1340724146.456:1): initialized
    [ 0.457302] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.460514] VFS: Disk quotas dquot_6.5.2
    [ 0.460597] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.460751] msgmni has been set to 3939
    [ 0.461070] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    [ 0.461121] io scheduler noop registered
    [ 0.461125] io scheduler deadline registered
    [ 0.461224] io scheduler cfq registered (default)
    [ 0.461477] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
    [ 0.461710] pcieport 0000:00:1c.4: irq 41 for MSI/MSI-X
    [ 0.461950] pcieport 0000:00:1c.5: irq 42 for MSI/MSI-X
    [ 0.462157] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
    [ 0.462166] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
    [ 0.462198] pcieport 0000:00:1c.4: Signaling PME through PCIe PME interrupt
    [ 0.462203] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
    [ 0.462210] pcie_pme 0000:00:1c.4:pcie01: service driver pcie_pme loaded
    [ 0.462242] pcieport 0000:00:1c.5: Signaling PME through PCIe PME interrupt
    [ 0.462246] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
    [ 0.462253] pcie_pme 0000:00:1c.5:pcie01: service driver pcie_pme loaded
    [ 0.462369] vesafb: mode is 1024x768x32, linelength=4096, pages=0
    [ 0.462374] vesafb: scrolling: redraw
    [ 0.462379] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    [ 0.464035] vesafb: framebuffer at 0x80000000, mapped to 0xffffc90004980000, using 3072k, total 3072k
    [ 0.508030] Console: switching to colour frame buffer device 128x48
    [ 0.551844] fb0: VESA VGA frame buffer device
    [ 0.551863] efifb: dmi detected MacBook4,1 - framebuffer at 0x80000000 (1024x768, stride 4096)
    [ 0.551868] intel_idle: does not run on family 6 model 23
    [ 0.551930] GHES: HEST is not enabled!
    [ 0.552035] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.552762] Linux agpgart interface v0.103
    [ 0.552879] i8042: PNP: No PS/2 controller found. Probing ports directly.
    [ 0.553759] i8042: No controller found
    [ 0.553878] mousedev: PS/2 mouse device common for all mice
    [ 0.553966] rtc_cmos 00:08: RTC can wake from S4
    [ 0.554165] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
    [ 0.554204] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
    [ 0.554221] cpuidle: using governor ladder
    [ 0.554225] cpuidle: using governor menu
    [ 0.554454] TCP: cubic registered
    [ 0.554641] NET: Registered protocol family 10
    [ 0.554976] NET: Registered protocol family 17
    [ 0.554983] Registering the dns_resolver key type
    [ 0.555206] PM: Hibernation image not present or could not be loaded.
    [ 0.555216] registered taskstats version 1
    [ 0.556175] rtc_cmos 00:08: setting system clock to 2012-06-26 15:22:26 UTC (1340724146)
    [ 0.556299] Initializing network drop monitor service
    [ 0.558944] Freeing unused kernel memory: 740k freed
    [ 0.559290] Write protecting the kernel read-only data: 8192k
    [ 0.568413] Freeing unused kernel memory: 1588k freed
    [ 0.572710] Freeing unused kernel memory: 640k freed
    [ 0.586045] udevd[40]: starting version 185
    [ 0.590818] [drm] Initialized drm 1.1.0 20060810
    [ 0.592306] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
    [ 0.592621] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
    [ 0.594306] agpgart-intel 0000:00:00.0: detected 16384K stolen memory
    [ 0.594543] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
    [ 0.595388] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
    [ 0.595444] ACPI: Lid Switch [LID0]
    [ 0.595539] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
    [ 0.595547] ACPI: Power Button [PWRB]
    [ 0.595632] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
    [ 0.595639] ACPI: Sleep Button [SLPB]
    [ 0.595763] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    [ 0.595769] ACPI: Power Button [PWRF]
    [ 0.596508] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
    [ 0.596517] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
    [ 0.602545] i915 0000:00:02.0: setting latency timer to 64
    [ 0.749351] i915 0000:00:02.0: irq 43 for MSI/MSI-X
    [ 0.749367] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
    [ 0.749370] [drm] Driver supports precise vblank timestamp query.
    [ 0.749462] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 1.117606] [drm] initialized overlay support
    [ 1.299854] checking generic (80000000 300000) vs hw (80000000 10000000)
    [ 1.299860] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
    [ 1.299886] Console: switching to colour dummy device 80x25
    [ 1.301293] fbcon: inteldrmfb (fb0) is primary device
    [ 1.430434] Console: switching to colour frame buffer device 160x50
    [ 1.435865] fb0: inteldrmfb frame buffer device
    [ 1.435868] drm: registered panic notifier
    [ 1.435878] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [ 1.456696] Refined TSC clocksource calibration: 2393.999 MHz.
    [ 1.456705] Switching to clocksource tsc
    [ 1.821716] usbcore: registered new interface driver usbfs
    [ 1.821753] usbcore: registered new interface driver hub
    [ 1.826806] usbcore: registered new device driver usb
    [ 1.827520] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 1.827588] ehci_hcd 0000:00:1a.7: setting latency timer to 64
    [ 1.827594] ehci_hcd 0000:00:1a.7: EHCI Host Controller
    [ 1.827633] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
    [ 1.827675] ehci_hcd 0000:00:1a.7: debug port 1
    [ 1.831556] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
    [ 1.831587] ehci_hcd 0000:00:1a.7: irq 21, io mem 0x90704c00
    [ 1.842320] SCSI subsystem initialized
    [ 1.845102] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
    [ 1.845354] hub 1-0:1.0: USB hub found
    [ 1.845362] hub 1-0:1.0: 4 ports detected
    [ 1.845549] ehci_hcd 0000:00:1d.7: setting latency timer to 64
    [ 1.845555] ehci_hcd 0000:00:1d.7: EHCI Host Controller
    [ 1.845572] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
    [ 1.845613] ehci_hcd 0000:00:1d.7: debug port 1
    [ 1.847254] uhci_hcd: USB Universal Host Controller Interface driver
    [ 1.850589] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
    [ 1.850624] ehci_hcd 0000:00:1d.7: irq 20, io mem 0x90704800
    [ 1.851193] libata version 3.00 loaded.
    [ 1.860054] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [ 1.860280] hub 2-0:1.0: USB hub found
    [ 1.860289] hub 2-0:1.0: 6 ports detected
    [ 1.860472] uhci_hcd 0000:00:1a.0: setting latency timer to 64
    [ 1.860478] uhci_hcd 0000:00:1a.0: UHCI Host Controller
    [ 1.860494] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
    [ 1.860539] uhci_hcd 0000:00:1a.0: irq 20, io base 0x000060c0
    [ 1.860750] hub 3-0:1.0: USB hub found
    [ 1.860757] hub 3-0:1.0: 2 ports detected
    [ 1.860892] uhci_hcd 0000:00:1a.1: setting latency timer to 64
    [ 1.860898] uhci_hcd 0000:00:1a.1: UHCI Host Controller
    [ 1.860912] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
    [ 1.860965] uhci_hcd 0000:00:1a.1: irq 16, io base 0x000060a0
    [ 1.861172] hub 4-0:1.0: USB hub found
    [ 1.861178] hub 4-0:1.0: 2 ports detected
    [ 1.861312] uhci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 1.861318] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 1.861332] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
    [ 1.861366] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00006080
    [ 1.861578] hub 5-0:1.0: USB hub found
    [ 1.861585] hub 5-0:1.0: 2 ports detected
    [ 1.861717] uhci_hcd 0000:00:1d.1: setting latency timer to 64
    [ 1.861723] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 1.861744] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
    [ 1.861795] uhci_hcd 0000:00:1d.1: irq 18, io base 0x00006060
    [ 1.862003] hub 6-0:1.0: USB hub found
    [ 1.862010] hub 6-0:1.0: 2 ports detected
    [ 1.862142] uhci_hcd 0000:00:1d.2: setting latency timer to 64
    [ 1.862148] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 1.862165] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
    [ 1.862200] uhci_hcd 0000:00:1d.2: irq 21, io base 0x00006040
    [ 1.862411] hub 7-0:1.0: USB hub found
    [ 1.862417] hub 7-0:1.0: 2 ports detected
    [ 1.862917] ata_piix 0000:00:1f.1: version 2.13
    [ 1.862932] ata_piix 0000:00:1f.1: power state changed by ACPI to D0
    [ 1.862937] ata_piix 0000:00:1f.1: power state changed by ACPI to D0
    [ 1.862993] ata_piix 0000:00:1f.1: setting latency timer to 64
    [ 1.869158] scsi0 : ata_piix
    [ 1.874884] scsi1 : ata_piix
    [ 1.875449] ata1: PATA max UDMA/100 cmd 0x6108 ctl 0x6124 bmdma 0x60e0 irq 21
    [ 1.875454] ata2: PATA max UDMA/100 cmd 0x6100 ctl 0x6120 bmdma 0x60e8 irq 21
    [ 1.875665] ata_piix 0000:00:1f.2: MAP [ P0 -- -- -- ]
    [ 1.875722] ata_piix 0000:00:1f.2: setting latency timer to 64
    [ 1.881780] scsi2 : ata_piix
    [ 1.887944] scsi3 : ata_piix
    [ 1.888739] ata3: SATA max UDMA/133 cmd 0x60f8 ctl 0x611c bmdma 0x6020 irq 18
    [ 1.888745] ata4: SATA max UDMA/133 cmd 0x60f0 ctl 0x6118 bmdma 0x6028 irq 18
    [ 2.033862] ata1.00: ATAPI: MATSHITADVD-R UJ-867, HB01, max UDMA/66
    [ 2.065117] ata1.00: configured for UDMA/66
    [ 2.065887] ata3.00: ATA-8: Hitachi HTS542516K9SA00, BBCAC3GP, max UDMA/133
    [ 2.065893] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
    [ 2.067318] scsi 0:0:0:0: CD-ROM MATSHITA DVD-R UJ-867 HB01 PQ: 0 ANSI: 5
    [ 2.077869] ata3.00: configured for UDMA/133
    [ 2.078045] scsi 2:0:0:0: Direct-Access ATA Hitachi HTS54251 BBCA PQ: 0 ANSI: 5
    [ 2.087306] sr0: scsi3-mmc drive: 62x/62x writer cd/rw xa/form2 cdda tray
    [ 2.087313] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.088645] sr 0:0:0:0: Attached scsi CD-ROM sr0
    [ 2.093226] sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
    [ 2.093312] sd 2:0:0:0: [sda] Write Protect is off
    [ 2.093318] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.093371] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.184704] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
    [ 2.184707] sda3: <bsd:bad subpartition - ignored
    [ 2.184709] bad subpartition - ignored
    [ 2.184710] bad subpartition - ignored
    [ 2.184712] bad subpartition - ignored
    [ 2.184713] >
    [ 2.185557] sd 2:0:0:0: [sda] Attached SCSI disk
    [ 2.260045] usb 2-4: new high-speed USB device number 2 using ehci_hcd
    [ 2.770036] usb 3-1: new full-speed USB device number 2 using uhci_hcd
    [ 2.948125] usbhid 3-1:1.0: couldn't find an input interrupt endpoint
    [ 2.948381] usbcore: registered new interface driver usbhid
    [ 2.948385] usbhid: USB HID core driver
    [ 3.170028] usb 7-1: new low-speed USB device number 2 using uhci_hcd
    [ 3.179293] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
    [ 3.576705] usb 7-2: new full-speed USB device number 3 using uhci_hcd
    [ 5.022890] udevd[198]: starting version 185
    [ 5.426262] applesmc: SIS!ui16\xffffffc0\xffffffa6: read arg fail
    [ 5.562551] applesmc: key=220 fan=1 temp=10 acc=1 lux=0 kbd=0
    [ 5.562558] applesmc: init_smcreg() took 50 ms
    [ 5.584285] input: applesmc as /devices/platform/applesmc.768/input/input5
    [ 5.658889] lib80211: common routines for IEEE802.11 drivers
    [ 5.658894] lib80211_crypt: registered algorithm 'NULL'
    [ 5.711977] cfg80211: Calling CRDA to update world regulatory domain
    [ 5.924357] wl: module license 'Mixed/Proprietary' taints kernel.
    [ 5.924364] Disabling lock debugging due to kernel taint
    [ 5.946193] INFO @wl_cfg80211_attach : Registered CFG80211 phy
    [ 6.001836] lib80211_crypt: registered algorithm 'TKIP'
    [ 6.002152] eth0: Broadcom BCM4328 802.11 Hybrid Wireless Controller 5.100.82.112
    [ 6.084085] Linux media interface: v0.10
    [ 6.133183] iTCO_vendor_support: vendor-support=0
    [ 6.134458] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
    [ 6.134601] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x0460)
    [ 6.134703] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 6.156626] ACPI: Battery Slot [BAT0] (battery absent)
    [ 6.163544] ACPI: AC Adapter [ADP1] (on-line)
    [ 6.164216] ACPI: Requesting acpi_cpufreq
    [ 6.173706] Monitor-Mwait will be used to enter C-1 state
    [ 6.178506] Monitor-Mwait will be used to enter C-2 state
    [ 6.183424] Monitor-Mwait will be used to enter C-3 state
    [ 6.183457] Marking TSC unstable due to TSC halts in idle
    [ 6.183507] ACPI: acpi_idle registered with cpuidle
    [ 6.183963] Switching to clocksource hpet
    [ 6.210896] ACPI Warning: 0x000000000000efa0-0x000000000000efbf SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20120320/utaddress-251)
    [ 6.210909] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 6.242033] input: PC Speaker as /devices/platform/pcspkr/input/input6
    [ 6.275396] microcode: CPU0 sig=0x10676, pf=0x80, revision=0x60c
    [ 6.338786] Linux video capture interface: v2.00
    [ 6.426865] uvcvideo: Found UVC 1.00 device Built-in iSight (05ac:8501)
    [ 6.429319] uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
    [ 6.429831] usbcore: registered new interface driver uvcvideo
    [ 6.429835] USB Video Class driver (1.1.1)
    [ 6.496844] firewire_ohci 0000:04:03.0: added OHCI v1.0 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
    [ 6.587003] sky2: driver version 1.30
    [ 6.587217] sky2 0000:03:00.0: Yukon-2 EC Ultra chip revision 3
    [ 6.587761] sky2 0000:03:00.0: irq 44 for MSI/MSI-X
    [ 6.588473] sky2 0000:03:00.0: eth1: addr 00:22:41:21:43:0c
    [ 6.654740] microcode: CPU1 sig=0x10676, pf=0x80, revision=0x60c
    [ 6.655770] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 6.661489] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
    [ 6.700987] udevd[214]: renamed network interface eth0 to wlan0
    [ 6.824841] hda_codec: ALC889A: SKU not ready 0x400000f0
    [ 6.827442] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input7
    [ 6.848101] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
    [ 6.850714] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
    [ 6.942266] appletouch: Geyser mode initialized.
    [ 6.942380] input: appletouch as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.1/input/input10
    [ 6.942768] usbcore: registered new interface driver appletouch
    [ 6.996893] firewire_core 0000:04:03.0: created device fw0: GUID 002241fffe41d624, S400
    [ 7.131526] apple 0003:05AC:8242.0001: hiddev0,hidraw0: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
    [ 7.135766] input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.0/input/input11
    [ 7.136230] apple 0003:05AC:0229.0002: input,hidraw1: USB HID v1.11 Keyboard [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.2-2/input0
    [ 7.139354] input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input12
    [ 7.139526] apple 0003:05AC:0229.0003: input,hidraw2: USB HID v1.11 Device [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.2-2/input2
    [ 7.423516] usb 3-1: USB disconnect, device number 2
    [ 7.650081] usb 3-1: new full-speed USB device number 3 using uhci_hcd
    [ 8.322211] Bluetooth: Core ver 2.16
    [ 8.322655] NET: Registered protocol family 31
    [ 8.322660] Bluetooth: HCI device and connection manager initialized
    [ 8.322665] Bluetooth: HCI socket layer initialized
    [ 8.322669] Bluetooth: L2CAP socket layer initialized
    [ 8.322680] Bluetooth: SCO socket layer initialized
    [ 8.359817] usbcore: registered new interface driver btusb
    [ 9.183365] EXT4-fs (sda2): re-mounted. Opts: (null)
    [ 9.336886] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
    [ 9.377553] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
    [ 9.380170] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
    [ 9.497613] Adding 4184928k swap on /dev/sda5. Priority:-1 extents:1 across:4184928k
    [ 11.804445] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [ 11.845740] Bluetooth: RFCOMM TTY layer initialized
    [ 11.845751] Bluetooth: RFCOMM socket layer initialized
    [ 11.845755] Bluetooth: RFCOMM ver 1.11
    [ 12.221084] fbsplashd.stati[78]: segfault at 2c ip 000000000040579b sp 00007f2267333d00 error 4 in fbsplashd.static (deleted)[400000+233000]
    [ 24.154605] sky2 0000:03:00.0: eth1: enabling interface
    [ 24.155329] ADDRCONF(NETDEV_UP): eth1: link is not ready
    [ 28.831988] EXT4-fs (sda2): re-mounted. Opts: commit=0
    [ 28.933444] EXT4-fs (sda6): re-mounted. Opts: commit=0
    [ 29.363373] wlan0: no IPv6 routers present
    [ 30.487575] sky2 0000:03:00.0: eth1: disabling interface
    [ 30.500233] sky2 0000:03:00.0: eth1: enabling interface
    [ 30.501015] ADDRCONF(NETDEV_UP): eth1: link is not ready
    [ 40.563473] wlan0: no IPv6 routers present
    [ 45.535875] fuse init (API version 7.18)
    [ 70.827136] ISO 9660 Extensions: Microsoft Joliet Level 3
    [ 70.867639] ISO 9660 Extensions: RRIP_1991A
    [ 398.754336] ip_tables: (C) 2000-2006 Netfilter Core Team
    [ 398.776167] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
    [ 422.037689] Inbound IN=wlan0 OUT= MAC=00:21:e9:dc:77:c2:00:16:0a:19:9d:62:08:00 SRC=173.194.70.125 DST=192.168.50.100 LEN=78 TOS=0x00 PREC=0x00 TTL=42 ID=16396 PROTO=TCP SPT=5222 DPT=38798 WINDOW=369 RES=0x00 ACK PSH URGP=0
    [ 422.311888] Inbound IN=wlan0 OUT= MAC=00:21:e9:dc:77:c2:00:16:0a:19:9d:62:08:00 SRC=173.194.70.125 DST=192.168.50.100 LEN=78 TOS=0x00 PREC=0x00 TTL=42 ID=16397 PROTO=TCP SPT=5222 DPT=38798 WINDOW=369 RES=0x00 ACK PSH URGP=0
    [ 422.859975] Inbound IN=wlan0 OUT= MAC=00:21:e9:dc:77:c2:00:16:0a:19:9d:62:08:00 SRC=173.194.70.125 DST=192.168.50.100 LEN=78 TOS=0x00 PREC=0x00 TTL=42 ID=16398 PROTO=TCP SPT=5222 DPT=38798 WINDOW=369 RES=0x00 ACK PSH URGP=0
    [ 423.955325] Inbound IN=wlan0 OUT= MAC=00:21:e9:dc:77:c2:00:16:0a:19:9d:62:08:00 SRC=173.194.70.125 DST=192.168.50.100 LEN=78 TOS=0x00 PREC=0x00 TTL=42 ID=16399 PROTO=TCP SPT=5222 DPT=38798 WINDOW=369 RES=0x00 ACK PSH URGP=0
    [ 426.147338] Inbound IN=wlan0 OUT= MAC=00:21:e9:dc:77:c2:00:16:0a:19:9d:62:08:00 SRC=173.194.70.125 DST=192.168.50.100 LEN=78 TOS=0x00 PREC=0x00 TTL=42 ID=16400 PROTO=TCP SPT=5222 DPT=38798 WINDOW=369 RES=0x00 ACK PSH URGP=0
    [ 430.531638] Inbound IN=wlan0 OUT= MAC=00:21:e9:dc:77:c2:00:16:0a:19:9d:62:08:00 SRC=173.194.70.125 DST=192.168.50.100 LEN=78 TOS=0x00 PREC=0x00 TTL=42 ID=16401 PROTO=TCP SPT=5222 DPT=38798 WINDOW=369 RES=0x00 ACK PSH URGP=0
    00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03)
    00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 03)
    00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) (rev 03)
    00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03)
    00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)
    00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03)
    00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
    00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03)
    00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 03)
    00:1c.5 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 6 (rev 03)
    00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03)
    00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03)
    00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03)
    00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03)
    00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
    00:1f.0 ISA bridge: Intel Corporation 82801HM (ICH8M) LPC Interface Controller (rev 03)
    00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03)
    00:1f.2 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [IDE mode] (rev 03)
    00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
    02:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03)
    03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8058 PCI-E Gigabit Ethernet Controller (rev 13)
    04:03.0 FireWire (IEEE 1394): LSI Corporation FW322/323 [TrueFire] 1394a Controller (rev 61)
    /etc/rc.conf:
    # /etc/rc.conf - Main Configuration for Arch Linux
    # See 'man 5 rc.conf' for more details
    # LOCALIZATION
    HARDWARECLOCK="UTC"
    TIMEZONE="Europe/Skopje"
    KEYMAP="us"
    CONSOLEFONT=
    CONSOLEMAP=
    LOCALE="en_GB.UTF-8"
    DAEMON_LOCALE="yes"
    USECOLOR="yes"
    # HARDWARE
    MODULES=(applesmc wl uvcvideo)
    USEDMRAID="no"
    USEBTRFS="no"
    USELVM="no"
    # NETWORKING
    HOSTNAME=stefan.local
    interface=
    address=
    netmask=
    broadcast=
    gateway=
    NETWORK_PERSIST="no"
    # DAEMONS
    DAEMONS=(syslog-ng sensors dbus network @firestarter @bluetooth crond cmp-daemon gdm @wicd alsa)
    Thanks

    Army wrote:
    This might not help you a lot, but if you want a stable system, try using packages from the repo wherever possible, look at the news before you update your system and don't mess things up (like bad configuration etc.).
    When it comes to performance, you won't gain much by compiling linux by yourself! Just use the linux package from [core] or if you want a bit more performance, install the ck-kernel from
    [repo-ck]
    Server = http://repo-ck.com/$arch
    (this has to go to the bottom of /etc/pacman.conf)
    (use that one which is best for your cpu (in your case this might be the package linux-ck-corex).
    Hmmm, Linux-ck-corex doesn't even load.. I am now trying to install the generic one. Hope it works.
    Edit: I will first try linux-lqx...
    Last edited by exapplegeek (2012-06-26 18:33:31)

  • Inspection lot not getting generated for schedule in stability study

    Dear All,
    Need your urgent help to solve a issue. I need to perform inspection of material after specified interval of time for which i am using stability study process. Following are the steps which i have followed :
    1) Create initial sample (physical sample created)
    2) Confirm initial sample
    3) Initial test inspection lot( Inspection lot created )
    4) Complete initial test
    5) Specify storage conditions (Physical sample created with CRTD status)
    6) Create testing schedule( Maintenance schedule is created )
    7) I have scheduled maintenance plan through IP10 tcode. All the calls are getting generated.
    Now i have given manual call in IP10, but inspection lot is not generating.
    Please help to solve this issue ASAP.

    Dear Craig,
    Yes i have activated inspection type 16 to material master.
    Actually issue is solved now, I have missed one step " Store stability Sample".
    Now the lots are getting generated.
    i am closing this thread now.

  • After AVG PC Tune up, software update message for security and stability update is available FireFox 3.6.18. Should I Update?

    My Dell laptop (Operating on Windows XP) was hit with multiple viruses - I could not open Mozilla Firefox or any other applications for that matter. After much time and many attempts, I was finally able to install and run an AVG Scan and then an AVG PC Tune up. 4,559 problems found and repaired. After the repairs, I received the following message:
    "Software Update - A security and stability update for Firefox is available: Firefox 3.6.18 - It is strongly recommended that you apply this update for Firefox as soon as possible. - an underlined link reading, "View more information about this update" and then 2 choices - "Ask Later" or "Update Firefox." Since part of the problem was with Firefox and some error messages pointed to that, I'm hesitant to click on any of the three options above. Can you help me to get past this error message, please. I am sending this from my home computer. Thank you. Diane

    Sometimes the updater gets in a funny state - Go to http://www.mozilla.org/en-US/firefox/new/ and download the full installer. Close Firefox and run the installer

  • KT6 Delta stability and performance problems

    Hi all!
    My brother and I recently assembled my new computer. Since then I’ve been experiencing two problems that really bug me. I’m no expert at this stuff so if you guys need more info from me to try to help, just say so!
    Problem 1:
    The optimum setting for my processor is a CPU FSB Clock of 166 Mhz, but I’m only able to reach 160 Mhz. 161-163 will work but is extremely unstable. 164-166 will cause Windows to dump to a blue screen and reboot.
    I’ve seen that other people on this board have had similar problems. Note that I’ve set CPU Ratio to Auto and SDRAM Timing to SPD. What could be causing the problem? Could a simple BIOS update help (I’m running the one that was delivered with the motherboard)? How about clearing CMOS?
    Problem 2:
    Maybe due to the above problem, I’m also having stability problems when I do get into Windows. On some days it’s fine, other days it’s a mess.
    All of a sudden, while surfing the net or gaming, the computer will dump to a blue screen with the info that Windows has been shut down to prevent further damage to the system. One of two error messages will be displayed:
    “A thread tried to release a resource it did not own” (more common message) or “IRQL_NOT_LESS_OR_EQUAL” (less common).
    The computer will then reboot automatically. It’s really hard to specify when this happens: it could come at any time.
    The system I have is the following:
    KT6 Delta (MS-6590) motherboard
    AMD Athlon XP2500+ (1.833 Ghz)
    TwinMOS PC3200 DDR-DIMM (2x256Mb)
    Seagate Barracuda 80Gb S-ATA
    My old IDE 12 Gb harddrive
    PowerColor Radeon 9800 Pro 128Mb
    TDK CD-RW (40x/10x/40x)
    Windows XP Professional with Sp1
    Have any of you had similar problems? I appreciate any help I can get!!!
    Regards,
    Stefan

    judd321: couldn't agree more! Thanx to all the people who post here and try to help out computer illiterate people like myself. Interesting to see that you've had the same problem.
    Thought I'd give you an update on my situation. I've done some surfing and gotten some mixed messages. Some say that the included PSU that came with my Chenbro Gaming Bomb (FSP Group 350W, delivers 28A at +3,3V, 30A at +5v and 16A at 12V) is plenty to power a system with my specs. Others, like the good people on this board, claim that 350W just won't cut it.
    I've just invested in an Aspire 520W (looks creepy and mod-ish). The dealer claimed that it really does deliver 520W at maximum performance and not just at peak. Before I install it I will try the following just to make sure it's the PSU that's causing me problems:
    1) Confirm that I still cannot boot up with CPU Clock at 166Mhz. If all is still the same, Windows won't even start. If I, by the grace of the good Lord, do get my system running at 166, I'll monitor unwanted reboots. If system is stable, fine. If no:
    2) I'll start by clearing CMOS, with battery and power cord out for at least 10 minutes. Then enter BIOS and run default settings EXCEPT CPU Clock which I'll set to 166Mhz. I'll try to reboot computer to see if this has done the trick. If yes, great. If no, I'll try the same thing but also set memory speed to 333. If that still doesn't work:  
    3) Clear CMOS with power cord disconnected. Unplug unneccesary components like CD-ROM, fan (not heatsink  , floppy drive, any USB devices and my old IDE hard drive. Reboot the computer and set CPU Clock at 166. If the system works, it was definitely the PSU since the absence of the disconnected components will have allocated more power to the connected components. If it doesn't work...does anybody want to buy a pretty decent system that doesn't allow for full processor power and experiences frequent, unwanted reboots?  
    I'll let you know how things work out!

  • How can I improve the stability of itunes64bit 8.0.2 on my Vista system?

    Vista Home Premium: iTunes64bit: application crashes after adding album photos and then changing views (list, Album, split) or clicking on different playlists and back to the entire music library.
    The library has 42,000 items (mostly music) so it is quite large. At launch it takes a long time for itunes to load and display. There is no user cues telling me it is running. It simply displays after 60 or more seconds.
    Then I start working in the library, pasting pictures to multiple items, modifying album titles.
    After doing a few management tasks on my music items and navigating back and forth between the music library and playlist (changing views), the application stop being responsive and according to the log, the app just plainly crashes.
    Sometimes I can restart successfully but most of the times, I need to stop the itunes service or log-out before I can restart it successfully.
    I am using itunes64bit 8.0.2
    I am running it on a machine equipped with 4GB of ram and the library lives on a 500GB external hard drive plugged-in through USB 2.0.
    How can I improve the stability of itunes64bit on my system?
    Message was edited by: JF Boisvert

    This VI can be convert to labview 8.0 because subvi are not compatible with old version.
    I post a screenshot.
    Aurélien J.
    National Instruments France
    #adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
    >> Du 30 juin au 25 août, embarquez pour 2 mois de vidéo-t'chat ! Prenez place pour un voyage au coe...
    Attachments:
    image.jpg ‏38 KB

  • How can I fix the stability of my wifi module

    Hello I have an Imac 27" Core i7 3.4 Ghz 8Go Ram running under Lion 10.7.2,
    I am using a NAS connected through wifi,
    Everything worked well since july 2011, but since about a week my connection wifi seemes to be very unstable and it induces the finder to crash (or freeze),
    If I try to restart the finder it will not restart proprely, the computer hangs and all the other program crashes (probably as they cannot acces to ther network drive) and I cannot shutdown my Imac, I have each time to hold the power button for 10 second and then restart the computer,
    I suppose that the sutation was induced through a fix that was installed about a week ago,
    I did check with the software update, everthing is up to date,
    I am pretty sure that the wifi module is the cause as when the finder crashes I cannot turn the wifi off anymore,
    If I  turn the wifi off after booting my imac works perfecrtly.... though I really need my wifi connection to acces all my data on the NAS...
    Does any one have an idea how to fix this problem... or get back to the point I was before the "fix" screw my wifi module...
    By the way my wifi network is stable, I use it with several other devices without problem,
    Thanks in advance
    Pierre

    Acually I found the solution alone...
    Despite the poor stability of the wifi module the finder crashes were due to a corrupted Time machine file probably linked to the wifi interruption as my time machine backup is on my network drive...
    I erased the old backups, Initiated a new one, everything work fine.. but I have now an ugly 100 feet network cable through the house, so I still look forward to have a better wifi stability to get rid of it!!!

  • Sound Blaster Instability - Are you affected? (Stability Test for "Squealing", et

    I've created a test that works on my Sound Blaster Audigy 2 ZS with my particular hardware configuration as a proof of concept of the instability ( "high-pitched squealing" ) issues I have. (I have an ASUS P5N-E SLI motherboard.) I am seeking to find out if it "works" for other people with squealing issues (i.e. triggers them).
    Do our problems really have common symptoms, or a common source? I hope we can find that out, and ideally this would be a step toward that.
    I believe it would be helpful for people who have problems with their cards to post some system information, along with descriptions of what the problems are.
    Some useful system information to post would be . Motherboard, 2. CPU, 3. Video Card, 4. Sound Card, 5. Operating System, 6. Sound Driver and version, 7. Power Supply.
    .. and then whether you have problems with Snap-Crackle-Pop (SCP), High-Pitched Squealing (HPS), BSODs, or other errors.
    For example, here's my information:
    . ASUS P5N-E SLI
    2. Intel Core 2 Duo E6600
    3. ATI X800XT
    4. Sound Blaster Audigy 2 ZS
    5. Windows XP Pro SP2
    6. Creative drivers, 5.2.4.96 (SBAX_WBUP2_LB_2_09_006)
    7. Cooler Master iGreen Power 600W
    I experience HPS and BSODs. Typical times for the sound test to fail for me are between 5 seconds and 2 minutes.
    Some information is better than none. It's not necessary to give complete system information if you don't know it all. But the most important information would be what motherboard you have, what sound card you have, what problems you experience (if any) and whether or not the test results in instability for you.
    IMPORTANT: It's important to note that you are running this test AT YOUR OWN RISK, and while the files included don't inherently cause harm, it is possible for data corruption to occur if your system is affected by this issue.
    These key files are needed in order to perform the test: a MIDI and a high-definition audio file (in this case, a high-definition (24-bit/48kHz) WAVE of near-silence). These are included in the zip file I have linked to below. According to CreativeSkeptic, MIDI playback makes high utilization of the PCI bus, so this may be why the problem is caused so easily this way.
    I would be interested in hearing your results if you have experienced the high-pitched squealing in games or even if you haven't.
    You can hear an example of what may happen if you experience instability [url="http://www.supload.com/listen?s=Sxfea3MfL">here[/url].
    Sound Blaster Test.zip at Wikiupload.com
    Or.. Sound_blaster_test.Zip by Bigupload.Com
    (Note: The zip file is around 50KB in size, but it expands to over 42MB. This is due to the high-definition nature of the 5-minute wave file necessary to induce this problem in affected systems.)
    This test will measure the stability of your Sound Blaster in your
    particular system configuration. It is tested with Windows XP and
    Windows Media Player , though these *may* not be essential for the
    functioning of the test.
    WARNING:
    CLOSE ALL RUNNING PROGRAMS TO AVOID DATA LOSS AS MUCH AS POSSIBLE.
    Instructions:
    . Open silence.wav in Windows Media Player. To do so, you can drag it
    onto the Windows Media Player shortcut in this folder.
    2. Then, open the Play Midi shortcut.
    Note:
    This test will ONLY work if your system is using standard or full
    hardware sound acceleration. In addition, your system must be using
    your Sound Blaster as its MIDI interface directly. Software synthesizers
    will not trigger the problem.
    You can tell if your system has become unstable based on the
    corrupted nature of the instruments played by the MIDI. It will
    begin to sound odd and unnatural, with random notes inserted
    here and there. It will be clear to you that this has happened.
    For me, it doesn't take more than a few minutes before the instability
    appears.
    If this is the case, it is recommended that you do one of two things:
    - Press the RESET button on your computer.
    - Pull the power plug, if you have no reset button.
    This is to avoid data loss associated with a blue screen of death
    that would normally occur if you did not take these measures to
    prevent it.
    If you do experience these stability issues, you are at risk of BSOD's
    when gaming or other playback problems. Please report this in the forum.
    To hear a sample case of instability, visit the following URL:
    http://www.supload.com/listen?s=Sxfea3MfLMessage Edited by sireebob on 03-25-200708:2 PM

    My X-Fi XtremeGamer passes this "test". No BSODs, etc. But I've discovered my computer has problems beyond sound card issues (I didn't even notice them until recently).
    In other words, I've seen firsthand (whether this is true for the majority or not) that my issues with the Audigy 2 ZS don't translate exactly over to the X-Fi XtremeGamer, so if you have an X-Fi don't expect problems with this test, but by all means try if you want to see for sure.
    (One problem remains from the Audigy 2 ZS, however: randomly skipping ahead in videos or certain audio streams. It doesn't happen with onboard audio, but my tendency is still to call this a system problem unrelated to the sound card because it doesn't happen on my old PC.)
    (Oh, and I know I'm replying to my own post, so don't think I'm nuts. I just thought it would be appropriate to report my experience with my new card in another post.)Message Edited by sireebob on 03-27-20072:24 PM

  • I am feeling so ripped off right now. I have wanted a Mac for years and believed the hype about it's stability and I have had more trouble with this Imac 2011 than I have ever had with a pc. It locks up with several software products from APP store.

    I am feeling so ripped off right now. I have wanted a Mac for years and believed the hype about it's stability and I have had more trouble with this Imac 2011 than I have ever had with a pc. It locks up with several software products from APP store. I have already had to have a technician to look at it and really couldn't figure out what the deal was.  I was told that the APP store software should give me no problems but the truth is that it locks up on the software. This machine is only 4 weeks old and I am using 37 g on a 1 T hard drive. There is no reason for it to be locking up. Also, when I try to use the help program, it always tells me that I am not connected to the internet even though I have used both the mail program and the browser with no problem just before that. I successfully used the help program on my pc lots of times. I did not need a $2000. plus machine to just get email. I just wanted to unload on somebody that might understand my pain and after checking out this site...I think there is a few of you out there.

    I was told that the APP store software should give me no problems but the truth is that it locks up on the software.
    The apps downloaded from the Mac App Store are written by third party developers, not Apple. If you have problems  with those apps you need to visit the support area for their websites. Launch the App Store, locate the app name. You should see a support link.
    when I try to use the help program, it always tells me that I am not connected to the internet even though I have used both the mail program and the browser with no problem just before that
    Go to ~/Library/Preferences. Move the com.apple.helpviewer.plist file from the Preferences folder to the Trash. Restart your Mac, try the Help menu.
    If you need help finding that file, hold down the Finder icon in the Dock then click: New Finder Window. From the menu bar top of your screen click: Go > Go to Folder. Type this in exactly as you see it here:   ~/Library/Preferences/com.apple.helpviewer.plist    That will take you right to that file.
    (.plist) files stores information about a particular app or in this case, the Help viewer. Often times deleting the .plist file resolves the issue.
    It's fine to "unload"... we understand that you expect your iMac to be stable but there are times when things go awry. That's why we have these forums so that you can you get help.
    You may want to read up on how to repair the disk if necessary or reintsall Lion >  OS X Lion: About Lion Recovery
    Apple - Find Out How - Mac Basics
    How to "switch" from PC to Mac >  Apple - Support - Switch 101
    I'm sorry you feel, "ripped off", but you are using the world's most advanced operating system and it may take some time to adjust to a new OS.   http://developer.apple.com/technologies/mac/

Maybe you are looking for

  • Is it possible to LOAD and INSTALL applet during pre-personalization?

    Hi Friends.. Currently, i use JCOP card I want to know the other way to LOAD and INSTALL applet not through CardManager.. I mean, is it possible to LOAD and INSTALL applet during pre-personalization time?. Thanks in advance

  • Error when Execute the Interface

    Hi All, I'm a newbie in ODI..I have some problem when i'm execute my interface.. My source is from .csv and my target is essbase.. Here is the error message when it executed... 7000 : null : java.sql.SQLException: Malformed INSERT statement. java.sql

  • Opening a chatbox i only get "undefined" in the box and cant type

    open a customer support chatbox and i get the box but only the word "undefined" where ever the real words should be in the box and cant even type in the box..

  • Sms programming

    Hi all, Can any body have an Idea about SMS development? Right now I am planning to develop an application which gives the users Bank Transaction.To do this application I written some servlet programming for server side operations.The problem is main

  • Temporary profile created in server 2012

    Hi Expert, I have a domain joined 2012 server, when I am trying to login to that server it says "you cannot access your files as it is a temporary profile".. I rebooted the server and perform this steps http://www.c-sharpcorner.com/UploadFile/shyjumo