Tiger stops Internet - data exchange after indefinite time ...

Hello,
For over a year now, I'm experiencing problems with my internet connection.
These attract attention by simply stopping the data transfer between my G5 and the internet; remind: the connecton remains (at least the VPN-connection) as if nothing happened.
To described it in detail:
1.) I connect via a VPN to the internet.
2.) Everything works fine after an indefinate period of time (15, 30 minutes or up to 2 hours) until suddenly the data transfer stops. Regardless which port I use, I'm not able to download / upload anything!
3.) I disconnect the VPN-connection and immediately connect again to the internet. It works but after some sort of time, the same strange behaviour (as described above) occurs again.
As you might noticed, I use a DSL-Ethernet modem which connects through the buildt-in VPN tunnel provied by the OS.
My first thought was that it could be due to my (telephone)-wire, but my ISP checked it several times with the conclusion that everything works perfectly.
I also tried disconnecting all devices (telephone, fax) which are connected to the wire. No success again.
Configuring the connection on 2 different system partitions (one of them OS X 10.3 Panther) won't change the situation. The problem still persists.
So there seems something wrong with my hardware - software configuration.
My hardware: Dual 2 GHz G5 (2004) connected to a SpeedTouch 510 Ethernet-modem via the built-in ethernet port. No router!
I've tried everything, so I hope to get some kind of help by a real expert.
The only explanation I have so far, lies on the ethernet port.
Also: 4 months ago my VGA failed powering my ADC-monitor, so it was exchanged by an Apple Authorised Service Provider. Is it possible that the VGA caused the damaging of the ethernet ports (if they are defective - I have no idea ...) ?
Please help me! I'm absolutely stumped and have no idea how to solve this!
Many thanks!
All the best,
Peter

FAQ
1. Best Effort Test: -provides background information.
Download Speed
4.39 Mbps
0 Mbps
4 Mbps
Max Achievable Speed
Download speedachieved during the test was - 4.39 Mbps
For your connection, the acceptable range of speeds is 1.2 Mbps-4 Mbps.
IP Profile for your line is - 4.5 Mbps
2. Upstream Test: -provides background information.
Upload Speed
0.82 Mbps
0 Mbps
0.83 Mbps
Max Achievable Speed
Upload speed achieved during the test was - 0.82Mbps
Additional Information:
Upstream Rate IP profile on your line is - 0.83 Mbps
We were unable to identify any performance problem with your service at this time.
It is possible that any problem you are currently, or had previously experienced may have been caused by traffic congestion on the Internet or by the server you were accessing responding slowly.
If you continue to encounter a problem with a specific server, please contact the administrator of that server in the first instance.

Similar Messages

How to stop a while loop after certain time using Elapsed time vi

how to stop a while loop after certain time using Elapsed time vi.

Hi Frankie,
Just place the Elapsed Time VI inside the WHILE loop, and wire the 'Time Has Elapsed' output to the conditional terminal in the lower right corner (which should be set to 'stop if true' by default).
In the future, please post your LabVIEW questions to the LabVIEW Forum. You have a much better chance of getting your questions answered sooner, and those answers can then help others who are searching the LabVIEW forums. Thanks!
Justin M
National Instruments

Why is the payment for e.g. a song in the itunes store proceeding not at once but after indefinite time?

Why is the payment for e.g. a song in the itunes store proceeding not at once but after indefinite time?

If you are using your account's balance then the price of the song should be deducted from it immediately, if you are using a credit card then it may take a day or two for it to appear on your card's statement

Data vanishing after some time

Hi,
We have enhanced standard info type 9 & added a custom field.
in PAI defaulting some value to this custom field.
In PA30 when we make changes to existing records it defaults the valu in the custom field and when we save it it saves to data base.
After some time the value in this field vanishes.
Any idea on this?

Hi
Create Audit log for infotype 0009 and check the user by which record is changed.
To create Audit log, make entries in -
1. V_T585A
2. V_T585B
3. V_T585C
Then run the report RPUAUD00 or tcode PC00_M16_UAUD (Payroll audit trail). Check if the record is changed by the user used to schedule background job.
Regards,
Rupesh
Edited by: rumhat on Apr 16, 2011 10:38 AM

Mail stops working with Exchange after VPN is launched and then stopped

Mail and Exchange is working fine for me on SL, except when I launch Nortel VPN / Apani to run a work app (other then mail), and then end the VPN session - apple mail doesn't connect to exhange anymore. If I restart the VPN, then it connects with exchange.
I prefer not to run the VPN as I don't need it 99% of the time (and Time Machine doesn't sync with Time Capsule if the VPN is up). I can't find a way to reset the connection or mail, so I end-up running the VPN all the time now, once I get stuck in this mode.
Anyone else seeing this behavior?

I have tried a number of things to get my HP1012 working under Snow Leopard and it will not work. neither will my Canoscan LIDE 200 unless I manually install the driver which HP says you cannot do for its printer. 10.6 may be intelligent but not very. Mac's idea of simple makes it too complicated to determine if and where there is a fault. You can't simply remove and reload the driver as per 10.5 Any ideas out there?

Fms live stream server stops sending data around 4+hrs

Hi,
I am having some issues with fms servers livestream connection. My rtmp client connects to the server ok and rtmp data flowing ok for about 4hours, in the wireshark trace I can see that the server just stops sending data roughly after 4hours. The server version is 3.5.1, and I also try it on a 4.0 server the data stops coming from the server as well after 5+hours. There are no errors or any indication of session disconneciton in the diagnostic logs. I have also looked thru the settings in applicaiton.xml and server.xml I just don't see any obviious reason for the issue. I do send rtmp Acknowledgement to server after the client receives "window size" bytes, and the client sends ping response to server. Are there any other that client needs to send back to server? It would be greatly appreciated for any pointers and help. Thanks.

Updates:
An interesting observation is that the server stops transmitting data when server-to-client bytes reaches ~4G. The number sounds too much like a system resource limitation. It is a live stream and it is not being recorded so I am not sure where is the 4G limitation coming from. FLVCACHE_MAXSIZE is for recorded stream, I think, and it is set to the default 500MB.
Also, in the access log the check point for connect-continue and play-continue keep showing status of 100, which is supposed to be "Waiting for the application to authenticate.". Is this correct? The connection is successfully connected and play command is successful as shown in the access log. swfVerification is disabled in application.xnl. what does the server waiting for in respect to authentication?
Below is the log:
connect-continue
session
2012-03-22
01:51:24
Eastern Daylight Time
10.200.4.224
10.200.4.172
1176
1
44
_defaultRoot_
_defaultVHost_
live
_definst_
0
100
10.200.4.224
rtmp
rtmp://10.200.4.172/live
rtmp://10.200.4.172/live
file:///mac.flv
LNX 9,0,48,0
4702111234558869871
3183
3840850027
normal
file:///mac.html
play-continue
stream
2012-03-22
01:51:24
Eastern Daylight Time
livestream
10.200.4.172
1176
1
44
_defaultRoot_
_defaultVHost_
live
_definst_
18044
100
10.200.4.224
rtmp
rtmp://10.200.4.172/live
rtmp://10.200.4.172/live
file:///mac.flv
LNX 9,0,48,0
4702111234558869871
3183
3840850027
normal
livestream
rtmp://10.200.4.172/live/livestream
rtmp://10.200.4.172/live/livestream
flv
18085866
0
3829693036
1
file:///mac.html
-1
-1.000000
Any pointers would be greatly appreciated. Thanks.

IE prompts credentials after some time and we get error rsHttpRuntimeClientDisconnectionError

Hi all,
Windows Server 2012
Reporting Services 2012 SP2
Internet Explorer 8
After some time running a report the end user is asked for his credentials again with the authentication prompt.
In the ExecutionLog we see the Client (IE) has its connection disconnected =
rsHttpRuntimeClientDisconnectionError
The server parameter are attached:
We appreciate any clue.
Thanks,
Alex Berenguer
Alex Berenguer

Hi Alex,
Per my understanding that you are running the report for sometime an then IE prompt for credential and you to this kind of error, right?
Based on my research, the "rsHttpRuntimeClientDisconnectionError" error may occur if:
Reporting Services creates the report and then goes to send it back to the client
Reporting Services finds out that the connection has been closed and responds with the disconnection error.
To resolve the issue, we can try to modify the TCP profile applied to the VIP.
Additionally, the issue may also occur due to a RESET coming from something between Report Server and the custom application. For example, an F5 NLB times these connections out on the either an HTTP or TCP level.
If your problem still exists, please also check if you will got the same problem on the other browser(firefox)，you can also provide us more details information about the
TimeDataRetrieval,TimeProcessing,TimeRendering in the ExecutionLog table.
Similar thread for your reference:
ssrs Report taking to much time to load
If you still have any problem, please feel free to ask.
Regards,
Vicky Liu
If you have any feedback on our support, please click
here.
Vicky Liu
TechNet Community Support

Hi Team, Showing Yellow icons after every 15 to 20 Min and internet stop working.when we enable- disbale the network connection then will internet start working fine.Some time network connection is disable but when we renable that connection it will st

Hi Team,
Showing Yellow icons after every 15 to 20 Min and internet stop working.when we enable- disbale the network connection then will internet start working fine.Some time network connection is disable but when we renable that connection it will stuck on enabling
and will not renable till i am not restart that machine. I have 350 Machine in network but facing this issue in 25 machines. Kindly help me on this issue .
Regards
Sahil bhateja

Hi，
So switch a LAN card fix this issue...seems a compatibility issue or maybe some packs or programs you installed recently cause this issue.
Have you manually check the network adapter driver from the PC's manufacture website? sometimes, it will be a time delay before Microsoft push out the driver update.
Check if issue exists in safemode with network, this mode will launch Windows with limited sets of files and drivers.
if you have a restore point, restore the pc to a previous point at which the pc is functioning fine.
Yolanda Zhu
TechNet Community Support

When trying to watch a movie via apple tv how can you stop it having to download each time and using up all my internet data?

I have bought movies from itunes and now they are on my computer why is it that each time I try to watch the movie it re downloads and uses up all my internet data? How do I prevent this and make it so it just plays from my stored version on my computer hard drive? Please help.

Welcome to the Apple Community.
Watch it from Computers > movies and not movies > purchased.

After installing yosemite on my laptop, once I open the internet through Safari, it at times will freeze or discontinue working causing me to close the wifi and turn it back on then reload the internet page to get it to work again. How to fix please?

After installing yosemite on my laptop, once I open the internet through Safari, it at times will freeze or discontinue working causing me to close the wifi and turn it back on then reload the internet page to get it to work again. Is there any way to fix this?

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
The test works on OS X 10.7 ("Lion") and later. I don't recommend running it on older versions of OS X. It will do no harm, but it won't do much good either.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message. See, for example, this discussion.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. Try to test under conditions that reproduce the problem, as far as possible. For example, if the computer is sometimes, but not always, slow, run the test during a slowdown.
You may have started up in "safe" mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(1310 ' 0.5 0.25 50 1000 15 5120 1000 25000 6 6 5 1 0 100 ' 51 25600 4 10 25 5120 102400 1000 25 1536 500 40 500 300 85 25 20480 262144 20 2000 524288 604800 5 1024 25 50 );k=({Soft,Hard}ware Memory Diagnostics Power FireWire Thunderbolt USB Bluetooth SerialATA Extensions Applications Frameworks PrefPane Fonts Displays PCI UniversalAccess InstallHistory ConfigurationProfile AirPort 'com\.apple\.' -\\t N\\/A 'AES|atr|udit|msa|dnse|ax|ensh|fami|FileS|fing|ft[pw]|gedC|kdu|etS|is\.|alk|ODSA|otp|htt|pace|pcas|ps-lp|rexe|rlo|rsh|smb|snm|teln|upd-[aw]|uuc|vix|webf' OSBundle{Require,AllowUserLoa}d 'Mb/s:Mb/s:ms/s:KiB/s:%:total:MB:total:lifetime:sampled:per sec' 'Net in:Net out:I/O wait time:I/O requests:CPU usage:Open files:Memory:Mach ports:Energy:Energy:File opens:Forks:Failed forks:System errors' 'tsA|[ST]M[HL]' PlistBuddy{,' 2>&1'}' -c Print' 'Info\.plist' CFBundleIdentifier );f=('\n%s'{': ','\n\n'}'%s\n' '\nRAM details\n%s\n' %s{' ','\n'{"${k[22]}",}}'%s\n' '%.1f GiB: %s\n' '\n    ...and %d more line(s)\n' '\nContents of %s\n    '"${k[22]}"'mod date: %s\n    '"${k[22]}"'size (B): %d\n    '"${k[22]}"'checksum: %d\n%s\n' );c=(879294308 4071182229 461455494 216630318 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 2636415542 3694147963 1233118628 2456546649 2806998573 2778718105 842973933 1383871077 1591517921 676087606 1445213025 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 3374894509 1051159591 892310726 1707497389 523110921 2883943871 3873345487 );s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[4]} ' s/:$//;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[9]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of|yc/!{ s/^.+is |\.//g;p;q;} ' ' BEGIN { FS="\f";if(system("A1 42 83 114")) d="^'"${k[21]}"'launch(d\.peruser\.[0-9]+|ctl\.(Aqua|Background|System))$";} { if($2~/[1-9]/) { $2="status: "$2;printf("'"${f[4]}"'",$1,$2);} else if(!d||$1!~d) print $1;} ' ' $1>1{$NF=$NF" x"$1} /\*/{if(!f)f="\n\t* Code injection"} {$1=""} 1;END{print f} ' ' NR==2&&$4<='${p[7]}'{print $4} ' ' BEGIN{FS=":"} ($1~"wir"&&$2>'${p[22]}') {printf("wired %.1f\n",$2/2^18)} ($1~/P.+ts/&&$2>'${p[19]}') {printf("paged %.1f\n",$2/2^18)} ' '/YLD/s/=/ /p' ' { q=$1;$1="";u=$NF;$NF="";gsub(/ +$/,"");print q"\f"$0"\f"u;} ' ' /^ {6}[^ ]/d;s/:$//;/([^ey]|[^n]e):/d;/e: Y/d;s/: Y.+//g;H;${ g;s/ \n (\n)/\1/g;s/\n +(M[^ ]+)[ -~]+/ (\1)/;s/\n$//;/( {8}[^ ].*){2,}/p;} ' 's:^:/:p;' ' !/, .+:/ { print;n++;} END{if(n<'{${p[12]},${p[13]}}')printf("^'"${k[21]}"'.+")} ' '|uniq' ' 1;END { print "/L.+/Scr.+/Templ.+\.app$";print "/L.+/Pri.+\.plugin$";if(NR<'{${p[14]},${p[21]}}') print "^/[Sp].+|'${k[21]}'";} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p;' '&&echo On' '/\.(bundle|component|framework|kext|mdimporter|plugin|qlgenerator|saver|wdgt|xpc)$/p' '/\.dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".","");print $0"$";} END { split("'"${c[*]}"'",c);for(i in c) print "\t"c[i]"$";} ' ' /^\/(Ap|Dev|Inc|Prev)/d;/((iTu|ok).+dle|\.(component|mailbundle|mdimporter|plugin|qlgenerator|saver|wdgt|xpc))$/p;' ' BEGIN{ FS="= "} $2 { gsub(/[()"]/,"",$2);print $2;} !/:/&&!$2{print "'${k[23]}'"} ' ' /^\//!d;s/^.{5}//;s/ [^/]+\//: \//p;' '>&-||echo No' '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[2]}'{$2=$2-1;print}' ' BEGIN { M1='${p[16]}';M2='${p[18]}';M3='${p[8]}';M4='${p[3]}';} !/^A/{next};/%/ { getline;if($5<M1) o["CPU"]="CPU: user "$2"%, system "$4"%";next;} $2~/^disk/&&$4>M2 { o[$2]=$2": "$3" ops/s, "$4" blocks/s";next;} $2~/^(en[0-9]|bridg)/ { if(o[$2]) { e=$3+$4+$5+$6;if(e) o[$2]=o[$2]"; errors "e"/s";next;};if($4>M3||$6>M4) o[$2]=$2": in "int($4/1024)", out "int($6/1024)" (KiB/s)";} END { for(i in o) print o[i];} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/) ' ' BEGIN{FS=": "} /^ {10}O/ {exit} /^ {0,12}[^ ]/ {next} $1~"Ne"&&$2!~/^In/{print} $1~"Si" { if(a[2]) next;split($2,a," ");if(a[1]-a[4]<'${p[5]}') print;};$1~"T"&&$2<'${p[20]}'{print};$1~"Se"&&$2!~"2"{print};' ' BEGIN { FS="\f";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1;} ' ' BEGIN { split("'"${p[1]}"'",m);FS="\f";} $2<=m[$1]{next} $1==9||$1==10 { "ps -c -ouid -p"$4"|sed 1d"|getline $4;} $1<11 { o[$1]=o[$1]"\n    "$3" (UID "int($4)"): "$2;} $1==11&&$5!~"^/dev" { o[$1]=o[$1]"\n    "$3" (UID "$4") => "$5" (status "$6"): "$2;} $1==12&&$5 { "ps -c -ocomm -p"$5"|sed 1d"|getline n;if(n) $5=n;o[$1]=o[$1]"\n    "$5" => "$3" (UID "$4"): "$2;} $1~/1[34]/ { o[$1]=o[$1]"\n    "$3" (UID "$4", error "$5"): "$2;} END { n=split("'"${k[27]}"'",u,":");for(i=n+1;i<n+4;i++)u[i]=u[n];split("'"${k[28]}"'",l,":");for(i=1;i<15;i++) if(o[i])print "\n"l[i]" ("u[i]")\n"o[i];} ' ' /^ {8}[^ ]/{print} ' ' BEGIN { L='${p[17]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n    "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n    [N/A]";"cksum "F|getline C;split(C, A);C=A[1];"stat -f%Sm "F|getline D;"stat -f%z "F|getline S;"file -b "F|getline T;if(T~/^Apple b/) { f="";l=0;while("'"${k[30]}"' "F|getline g) { l++;if(l<=L) f=f"\n    "g;};};if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F"\n    '"${k[22]}"'"T;printf("'"${f[8]}"'",F,D,S,C,f);if(l>L) printf("'"${f[7]}"'",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' 's/^.{52}(.+) <.+/\1/p' ' /id: N|te: Y/{i++} END{print i} ' ' /kext:/ { split($0,a,":");p=a[1];k[S]='${k[25]}';k[U]='${k[26]}';v[S]="Safe";v[U]="true";for(i in k) { s=system("'"${k[30]}"'\\ :"k[i]" \""p"\"/*/I*|grep -qw "v[i]);if(!s) a[1]=a[1]" "i;};if(!a[2]) a[2]="'"${k[23]}"'";printf("'"${f[4]}"'",a[1],a[2]);next;} !/^ *$/ { p="'"${k[31]}"'\\ :'"${k[33]}"' \""$0"\"/*/'${k[32]}'";p|getline b;close(p);if(b~/ .+:/||!b) b="'"${k[23]}"'";printf("'"${f[4]}"'",$0,b);} ' '/ en/!s/\.//p' ' NR>=13 { gsub(/[^0-9]/,"",$1);print;} ' ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?'${k[32]}'$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ / [VY]/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' '/^find: /!p;' ' /^p/{ s/.//g;x;s/\nu/'$'\f''/;s/(\n)c/\1'$'\f''/;s/\n\n//;p;};H;' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */    /;p;' ' s/^.+ |\(.+$$//g;p;' '1;END{if(NR<'${p[15]}')printf("^/(S|usr/(X|li))")}' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/^[1-9][0-9]{0,2}(\.[1-9][0-9]{0,2}){2}$/ { i++;n=n"\n"$1"\t"$3;} END{ if(i>1)print n} ' s/{'\.|jnl: ','P.+:'}'//;s/ +([0-9]+)(.+)/\2'$'\t\t''\1/p' ' /es: ./{ /iOS/d;s/^.+://;b0'$'\n'' };/^ +C.+ted: +[NY]/H;/:$/b0'$'\n'' d;:0'$'\n'' x;/: +N/d;s/://;s/\n.+//p;' ' 1d;/:$/b0'$'\n'' $b0'$'\n'' /(D|^ *Loc.+): /{ s/^.+: //;H;};/(B2|[my]): /H;d;:0'$'\n'' x;/[my]: [AM]|m: I.+p$|^\/Vo/d;s/(^|\n) [ -~]+//g;s/(.+)\n(.+)/\2:\1/;s/\n//g;/[ -~]/p;' 's/$/'$'\f''(0|-(4[34])?)$/p' '|sort'{'|uniq'{,\ -c},\ -nr} ' s/^/'{5,6,7,8,9,10}$'\f''/;s/ *'$'\f'' */'$'\f''/g;p;' 's/:.+$//p' '|wc -l' /{\\.{kext,xpc,'(appex|pluginkit)'}'\/(Contents\/)?'Info,'Launch[AD].+'}'\.plist$/p' 's/([-+.?])/\\\1/g;p' 's/, /\'$'\n/g;p' ' BEGIN{FS="\f"} { printf("'"${f[6]}"'",$1/2^30,$2);} ' ' /= D/&&$1!~/'{${k[24]},${k[29]}}'/ { getline d;if(d~"t") print $1;} ' ' BEGIN{FS="\t"} NR>1&&$NF!~/0x|\.([0-9]{3,}|[-0-9A-F]{36})$/ { print $NF"\f"a[split($(NF-1),a," ")];} ' '|tail -n'{${p[6]},${p[10]}} ' s/.+bus /Bus: /;s/,.+[(]/ /;s/,.+//p;' ' { $NF=$NF" Errors: "$1;$1="";} 1 ' ' 1s/^/\'$'\n''/;/^ +(([MNPRSV]|De|Li|Tu).+|Bus): .|d: Y/d;s/:$//;$d;p;' ' BEGIN { RS=",";FS=":";} $1~"name" { gsub(/["\\]/,"",$2);print $2;} ' '|grep -q e:/' '/[^ .]/p' '{ print $1}' ' /^ +N.+: [1-9]/ { i++;} END { if(i) print "system: "i;} ' ' NF { print "'{admin,user}' "$NF;exit;} ' ' /se.+ =/,/[\}]/!d;/[=\}]/!p ' ' 3,4d;/^ +D|Of|Fu| [0B]/d;s/^ |:$//g;$!H;${ x;/:/p;} ' ' BEGIN { FS=": ";} NR==1 { sub(":","");h="\n"$1"\n";} /:$/ { l=$1;next;} $1~"S"&&$2!~3 { getline;next;} /^ {6}I/ { i++;L[i]=l" "$2;} END { if(i) print h;for(j=0;j<'${p[24]}';j++) print L[i-j];} ' ' /./H;${ x;s/\n//;s/\n/, /g;/,/p;} ' ' {if(int($6)>'${p[25]}')printf("swap used %.1f\n",$6/1024)} ' ' BEGIN{FS="\""} $3~/ t/&&$2!~/'{${k[24]},${k[29]}}'/{print $2} ' ' int($1)>13 ' p ' BEGIN{FS="DB="} { sub(/\.db.*/,".db",$2);print $2;} ' {,1d\;}'/r%/,/^$/p' ' NR==1{next} NR>11||!$0{exit} {print $NF"\f"substr($0,1,32)"\f"$(NF-7)} ' '/e:/{print $2}' ' /^[(]/{ s/....//;s/$/:/;N;/: [)]$/d;s/\n.+ ([^ ]+).$/\1/;H;};${ g;p;} ' '1;END { exit "find /var/db/r*/'${k[21]}'*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom -mtime -'${p[23]}'s"|getline;} ' ' NR<='${p[26]}' { o=o"\n"$0;next;} { o="";exit;} END{print o|"sed 1d"} ' ' {o=o"\n"$0} NR==6{p=$1*$5} END{if(p>'${p[27]}'*10^6)print o|"sed 1d"} ' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab kextfind top pkgutil "${k[30]}\\" echo cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom 'mdfind -onlyin' env pluginkit scutil 'dtrace -q -x aggsortrev -n' security sed\ -En awk 'dscl . -read' networksetup mdutil lsof test osascript\ -e netstat mdls route cat uname powermetrics codesign lockstat lpstat );c2=(${k[21]}loginwindow\ LoginHook ' /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'" 'L*/Ca*/'${k[21]}'Saf*/E* -d 2 -name '${k[32]} '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' -i '-nl -print' '-F \$Sender -k Level Nle 3 -k Facility Req "'${k[21]}'('{'bird|.*i?clou','lsu|sha'}')"' "-f'%N: %l' Desktop {/,}L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message CRne '0xdc008012|(allow|call)ing|Goog|(mplet|nabl)ed|ry HD|safe b|succ|xpm' -k Message CReq 'bad |Can.t l|corru|dead|fail|GPU |hfs: Ru|inval|Limiti|v_c|NVDA[(]|pa(gin|us)|Purg(ed|in)| err|Refus|s ful|TCON|tim(ed? ?|ing )o|trig|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o%cpu,comm,ruid' "' syscall::recvfrom:return {@a[execname,uid]=sum(arg0)} syscall::sendto:return {@b[execname,uid]=sum(arg0)} syscall::open*:entry {@c[execname,uid,copyinstr(arg0),errno]=count()} syscall::execve:return, syscall::posix_spawn:return {@d[execname,uid,ppid]=count()} syscall::fork:return, syscall::vfork:return, syscall::posix_spawn:return /arg0<0/ {@e[execname,uid,arg0]=count()} syscall:::return /errno!=0/ {@f[execname,uid,errno]=count()} io:::wait-start {self->t=timestamp} io:::wait-done /self->t/ { this->T=timestamp - self->t;@g[execname,uid]=sum(this->T);self->t=0;} io:::start {@h[execname,uid]=sum(args[0]->b_bcount)} tick-10sec { normalize(@a,2560000);normalize(@b,2560000);normalize(@c,10);normalize(@d,10);normalize(@e,10);normalize(@f,10);normalize(@g,10000000);normalize(@h,10240);printa(\"1\f%@d\f%s\f%d\n\",@a);printa(\"2\f%@d\f%s\f%d\n\",@b);printa(\"11\f%@d\f%s\f%d\f%s\f%d\n\",@c);printa(\"12\f%@d\f%s\f%d\f%d\n\",@d);printa(\"13\f%@d\f%s\f%d\f%d\n\",@e);printa(\"14\f%@d\f%s\f%d\f%d\n\",@f);printa(\"3\f%@d\f%s\f%d\n\",@g);printa(\"4\f%@d\f%s\f%d\n\",@h);exit(0);} '" '-f -pfc /var/db/r*/'${k[21]}'*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag $ -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f'$'\f''%Sc'$'\f''%N -t%F {} \;' '/S*/*/Ca*/*xpc*' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' /\ kMDItemContentTypeTree=${k[21]}{bundle,mach-o-dylib} :Label "/p*/e*/{auto*,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {/p*,/usr/local}/e*/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*{,/*} .launchd.conf" list '-F "" -k Sender hidd -k Level Nle 3' /Library/Preferences/${k[21]}alf\ globalstate --proxy '-n get default' vm.swapusage --dns -get{dnsservers,info} dump-trust-settings\ {-s,-d,} '~ "kMDItemKind=Package"' '-R -ce -l1 -n5 -o'{'prt -stats prt','mem -stats mem'}',command,uid' -kl -l -s\ / '--regexp --files '${k[21]}'pkg.*' '+c0 -i4TCP:0-1023' ${k[21]}dashboard\ layer-gadgets '-d /L*/Mana*/$USER' '-app Safari WebKitDNSPrefetchingEnabled' '-Fcu +c0 -l' -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' '-F \$Message -k Sender kernel -k Message CReq "'{'n Cause: -','(a und|I/O |gnment |jnl_io.+)err|disk.+abo','USBF:.+bus'}'"' -name\ kMDItem${k[33]} -T\ hfs '-n get default' -listnetworkserviceorder :${k[33]} :CFBundleDisplayName $EUID {'$TMPDIR../C ','/{S*/,}'}'L*/{,Co*/*/*/L*/}{Cache,Log}s -type f -size +'${p[11]}'M -exec stat -f%z'$'\f''%N {} \;' \ /v*/d*/*/*l*d{,.*.$UID}/* '-app Safari UserStyleSheetEnabled' 'L*/A*/Fi*/P*/*/a*.json' users/$USER\ HomeDirectory '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' ' -F "\$Time \$(Sender): \$Message" -k Sender Rne "launchd|nsurls" -k Level Nle 3 -k Facility R'{'ne "user|','eq "'}'console" -k Message CRne "[{}<>]|asser|commit - no t|deprec|done |ect pas|fmfd|Goog|ksho|ndum|obso|realp|rned f|/root|sandbox ex" ' getenv '/ "kMDItemDateAdded>=\$time.now(-'${p[23]}')&&kMDItem'${k[33]}'=*"' -m\ / '' ' -F "\$Time \$(RefProc): \$Message" -k Sender Req launchd -k Level Nle 3 -k Message Rne "asse|bug|File ex|hij|Ig|Jet|key is|lid t|Plea|ship" ' print{,-disabled}\ {system,{gui,user}/$UID} '-n1 --show-initial-usage --show-process-energy' -r ' -F "\$Message" -k Sender nsurlstoraged -k Time ge -1h -k Level Nle 4 -k Message Req "^(ER|IN)" ' '/A* -type d -name *.app -prune ! -user 0' -vv '-D1 -IPRWck -s5 sleep 1' -o );N1=${#c2[@]};for j in {0..20};do c2[N1+j]=SP${k[j]}DataType;done;l=({Restricted\ ,Lock,Pro}files POST Battery {Safari,App,{Bad,Loaded}\ kernel,Firefox}\ extensions System\ load boot\ args FileVault\ {2,1} {Kernel,System,Console,launchd}\ log SMC Login\ hook 'I/O per process' 'High file counts' UID {System,Login,Agent,User}\ services\ {load,disabl}ed {Admin,Root}\ access Font\ issues Firewall Proxies DNS TCP/IP Wi-Fi 'Elapsed time (sec)' {Root,User}\ crontab {Global,User}' login items' Spotlight Memory\ pressure Listeners Widgets Parental\ Controls Prefetching Nets Volumes {Continuity,I/O,iCloud,HID,HCI}\ errors {User,System}\ caches/logs XPC\ cache Startup\ items Shutdown\ codes Heat Diagnostic\ reports Bad\ {plist,cache}s 'VM (GiB)' Bundles{,' (new)'} Trust\ settings Activity Free\ space Stylesheet Library\ paths{,' ('{shell,launchd}\)} Data\ packages Modifications CUPS );N3=${#l[@]};for i in {0..8};do l[N3+i]=${k[5+i]};done;F() { local x="${s[$1]}";[[ "$x" =~ ^([\&\|\<\>]|$) ]]&&{ printf "$x";return;};:|${c1[30]} "$x" 2>&-;printf "%s \'%s\'" "|${c1[30+$?]}" "$x";};A0() { Q=6;v[2]=1;id -G|grep -qw 80;v[1]=$?;((v[1]))||{ Q=7;sudo -v;v[2]=$?;((v[2]))||Q=8;};v[3]=`date +%s`;date '+Start time: %T %D%n';printf '\n[Process started]\n\n'>&4;printf 'Revision: %s\n\n' ${p[0]};};A1() { local c="${c1[$1]} ${c2[$2]}";shift 2;c="$c ` while [[ "$1" ]];do F $1;shift;done`";((P2))&&{ c="sudo $c";P2=;};v=`eval "$c"`;[[ "$v" ]];};A2() { local c="${c1[$1]}";[[ "$c" =~ ^(awk|sed ) ]]&&c="$c '${s[$2]}'"||c="$c ${c2[$2]}";shift 2;local d=` while [[ "$1" ]];do F $1;shift;done`;((P2))&&{ c="sudo $c";P2=;};local a;v=` while read a;do eval "$c '$a' $d";done<<<"$v";`;[[ "$v" ]];};A3(){ v=$((`date +%s`-v[3]));};export -f A1 A2 F;B1() { v=No;! ((v[1]))&&{ v=;P1=1;};};eval "`type -a B1|sed '1d;s/1/2/'`";B3(){ v[$1]="$v";};B4() { local i=$1;local j=$2;shift 2;local c="cat` while [[ "$1" ]];do F $1;shift;done`";v[j]=`eval "{ $c;}"<<<"${v[i]}"`;};B5(){ v="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d$'\e' <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F$'\e' ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`egrep -v "${v[$1]}"<<<"$v"|sort`;};eval "`type -a B7|sed '1d;s/7/8/;s/-v //'`";C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { B4 0 0 63&&C1 1 $1;};C4() { echo $'\t'"Part $((++P)) of $Q done at $((`date +%s`-v[3])) sec">&4;};C5() { sudo -k;pbcopy<<<"$o";printf '\n\tThe test results are on the Clipboard.\n\n\tPlease close this window.\n';exit 2>&-;};for i in 1 2;do eval D$((i-1))'() { A'$i' $@;C0;};';for j in 2 3;do eval D$((i+2*j-3))'() { local x=$1;shift;A'$i' $@;C'$j' $x;};';done;done;trap C5 2;o=$({ A0;D0 0 N1+1 2;D0 0 $N1 1;B1;C2 31;B1&&! B2&&C2 32;D2 22 15 63;D0 0 N1+2 3;D0 0 N1+15 17;D4 3 0 N1+3 4;D4 4 0 N1+4 5;D4 N3+4 0 N1+9 59;D0 0 N1+16 99;for i in 0 1 2;do D4 N3+i 0 N1+5+i 6;done;D4 N3+3 0 N1+8 71;D4 62 1 10 7;D4 10 1 11 8;B2&&D4 18 19 53 67;D2 11 2 12 9;D2 12 3 13 10;D2 13 32 70 101 25;D2 71 6 76 13;D2 45 20 52 66;A1 7 77 14;B3 28;A1 20 31 111;B6 0 28 5;B4 0 0 110;C2 66;B2&&D0 45 90 124;D4 70 8 15 38;D0 9 16 16 77 45;C4;B2&&D0 35 49 61 75 76 78 45;B2&&{ D0 28 17 45;C4;};B2&&{ A1 43 85 117;B3 29;B4 0 0 119 76 81 45;C0;B4 29 0 118 119 76 82 45;C0;    };D0 12 40 54 16 79 45;D0 12 39 54 16 80 45;D4 78 46 91;D4 74 25 77 15&&{ B4 0 8 103;B4 8 0;A2 18 74;B6 8 0 3;C3 75;};B2&&D4 19 21 0;B2&&D4 40 10 42;D2 2 0 N1+19 46 84;D2 44 34 43 53;D2 59 22 20 32;D2 33 0 N1+14 51;for i in {0..2};do A1 29 35+i 104+i;B3 25+i;done;B6 25 27 5;B6 0 26 5;B4 0 0 110;C2 69;D2 34 21 28 35;D4 35 27 29 36;A1 40 59 120;B3 18;A1 33 60 121;B8 18;B4 0 19 83;A1 27 32 39&&{ B3 20;B4 19 0;A2 33 33 40;B3 21;B6 20 21 3;};C2 36;D4 50 38 5 68;B4 19 0;D5 37 33 34 42;B2&&D4 46 35 45 55;D4 38 0 N1+20 43;B2&&D4 58 4 65 76 91;D4 63 4 19 44 75 95 12;B1&&{ D4 53 5 55 75 69&&D4 51 6 58 31;D4 56 5 56 97 75 98&&D0 0 N1+7 99;D2 55 5 27 84;D4 61 5 54 75 70;D4 14 5 14 96;D4 15 5 72 96;D4 17 5 78 96;C4;};D4 16 5 73 96;A1 13 44 74 18;C4;B3 4;B4 4 0 85;A2 14 61 89;B4 0 5 19 102;A1 17 41 50;B7 5;C3 8;B4 4 0 88;A2 14 24 89;C4;B4 0 6 19 102;B4 4 0 86;A2 14 61 89;B4 0 7 19 102;B5 6 7;B4 0 11 73 102;A1 42 86 114;j=$?;for i in 0 1 2;do ((i==2&&j==1))&&break;((! j))||((i))||B2&&A1 18 $((79+i-(i+53)*j)) 107+8*j 94 74||continue;B7 11;B4 0 0 11;C3 $((23+i*(1+i+2*j)));D4 $((24+i*(1+i+2*j))) 18-4*j 82+i-16*j $((112+((3-i)*i-40*j)/2));done;D4 60 4 21 24;D4 42 14 1 62;D4 43 37 2 90 48;D4 41 10 42;D2 48 36 47 25;A1 4 3 60&&{ B3 9;A2 14 61;B4 0 10 21;B4 9 0;A2 14 62;B4 0 0 21;B6 0 10 4;C3 5;};D4 9 41 69 100;D2 72 21 68 35;D2 49 21 48 49;B4 4 22 57 102;A1 21 46 56 74;B7 22;B4 0 0 58;C3 47;D4 54 5 7 75 76 69;D4 52 5 8 75 76 69;D4 57 4 64 76 91;D2 0 4 4 84;D2 1 4 51 84;D4 21 22 9 37;D0 0 N1+17 108;D4 76 24 38;A1 23 18 28 89;B4 0 16 22 102;A1 16 25 33;B7 16;B4 0 0 34;D1 31 47;D4 64 4 71 41;D4 65 5 87 116 74;C4;B4 4 12 26 89 23 102;for i in {0..3};do A1 0 N1+10+i 72 74;B7 12;B4 0 0 52;C3 N3+5+i;((i))||C4;done;A1 24 22 29;B7 12;B3 14;A2 39 57 30;B6 14 0 4;C3 67;A1 24 75 74;B4 1 1 122||B7 12;B4 0 0 123;B3 23;A2 39 57 30;B6 23 0 4;C3 68;B4 4 13 27 89 65;A1 24 23;B7 13;C3 73;B4 4 0 87;A2 14 61 89 20;B4 0 17;A1 26 50 64;B7 17;C3 6;A1 4 88;D5 77 44 89;D4 7 11 6;D0 0 N1+18 109;A3;C2 39;C4;} 4>&2 2>/dev/null;);C5
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. If you don't know the password, or if you prefer not to enter it, just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, a series of lines will appear in the Terminal window like this:
[Process started]
        Part 1 of 8 done at … sec
        Part 8 of 8 done at … sec
        The test results are on the Clipboard.
        Please close this window.
[Process completed]
The intervals between parts won't be exactly equal, but they give a rough indication of progress. The total number of parts may be different from what's shown here.
Wait for the final message "Process completed" to appear. If you don't see it within about ten minutes, the test probably won't complete in a reasonable time. In that case, press the key combination control-C or command-period to stop it and go to the next step. You'll have incomplete results, but still something.
12. When the test is complete, or if you stopped it because it was taking too long, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak for themselves, not for me. The test itself is harmless, but whatever else you're told to do may not be. For others who choose to run it, I don't recommend that you post the test results on this website unless I asked you to.
Copyright © 2014, 2015 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

On launching firfox v3.6.15 on windows vista this error message 'Script: file:///C:/Program%20Files/Mozilla%20Firefox/components/nsBlocklistService.js:648' is shown, after some time FF stops responding.

I've noticed that it is taking longer for Firefox to start. On launching the apps I get this message ' I've noticed that it is taking longer and longer for Firefox (always the most up-to-date version) to start. After some time FF stops responding

Create a new profile exclusively for the 4.0 beta version and create a desktop shortcut with -P "profile" appended to the target to launch that profile.
* http://kb.mozillazine.org/Testing_pre-release_versions
* http://kb.mozillazine.org/Creating_a_new_Firefox_profile_on_Windows
* http://kb.mozillazine.org/Shortcut_to_a_specific_profile
* http://kb.mozillazine.org/Using_multiple_profiles_-_Firefox

I downloaded from iTunes a hd movie for the first time. What a disaster ! Keep stopping and looks like after 2 days has not been downloaded. What am I suppose to do? Can I get my money back? How?

I downloaded from iTunes a hd movie for the first time. What a disaster ! Keep stopping and looks like after 2 days has not been downloaded. What am I suppose to do? Can I get my money back? How?

Contact iTunes suport... http://www.apple.com/support/itunes/contact/
It sounds like you might have a slow wifi internet connection? How fast is it with a speed test from your iPad.

How to use the (gigabit) ethernet for data exchange and WLAN for Internet?

I have following setup:
- MB Pro SL 10.6
- Desktop PC Windows 7
- Wireless Printer
- Netgear WLAN Router
At the moment all my data and internet communication is done via the WLAN router on 192.168.1.x That works fine and I can exchange data, print and surf the internet. My problem is that big data exchanges > 10GB take ages via my 54Mbit WLAN Connection. Furthermore the WLAN router is far away from the PC so that it is not possible to plug in the Ethernet Cable of the PC and the MB to the router.
Now I've thought that there must be a possibility to use a 1 gigabit (cross) cable (like in the 90s ;)) to connect the MB and the PC directly. I know that I will need different IP ranges and so on, but I have no clue how to do that.
The final solution should be that the setup stays as it is (data exchange, print, internet via WLAN) and that additional it is possible to connect PC and MAC some times for big transfers via a Gigabit ethernet cable. because I only want to connect those two machines I don't think that a switch makes any sense, or?
Does someone know how to do that?
Thanks a lot in advance!
Message was edited by: whitepowder

Well if it were 2 Macs, I would configure each Mac with a fixed IP address (same subnet as my router, but outside of the routers DHCP assignment range).
I would give the same fixed IP address to both my Airport AND my ethernet interfaces. I would do the same to the other Mac using another fixed IP address.
My network service order would have the ethernet higher than the Airport on both systems.
Normally I would use WiFi, so ethernet would be idle and out of the loop.
When I wanted faster transfers, I would connect each Mac to the router via their own ethernet cables, and the Mac would automatically detect that the ethernet became available, and would switch to use the faster ethernet. Since Airport and ethernet have the same fixed IP address, I could even do this in the middle of a file transfer and no one would notice as packets were always going to/from the same IP addresses, just using a different route, which doesn't matter.
NOTE: I've been doing this on Macs since Mac OS X 10.3 days (or was it 10.2; to long ago to remember).
However, you have thrown a Windows system into the mix, and since I do not use Windows, I do not have a clue about what can be done on Windows. However, maybe this will give you some ideas, and asking the right questions in a Windows oriented forum may provide the Windows side of this setup.
Sorry, that is the best I can do. Maybe my reply will encourage someone else to offer their approach.

Why does my iPad mini stop responding to wifi after a period of time?

Why does my iPad mini stop responding to wifi after a period of time?
For example, I can connect to wifi and use Safari and my iPad's interet capabilities with no problem. But if I then leave my iPad alone for an hour - when I go back to using it, it still shows as being connected to the wifi, but is unresponsive - i.e. web pages will not load etc. - I have to disconnect and reconnect to the wifi to make it responsive.
In advance, thanks

Try #5
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

HOW DO I STOP MY JSP PAGE FROM INSERTING DATA IN DATABASE EACH TIME REFRESH

Hi,
HOW DO I STOP MY JSP PAGE FROM INSERTING DATA IN DATABASE EACH TIME REFRESH?
Thanks

emekaco wrote:
Hi,
HOW DO I STOP MY JSP PAGE FROM INSERTING DATA IN DATABASE EACH TIME REFRESH?
ThanksSTOP SHOUTING!
now, while displaying the form generate some random number, or take the current time in millis or whatever. Put that number in a hidden field. Insert that unique number along with the real data into the database, but before you do check if the number already exists. If it does you can be pretty sure this is a resubmit of the same data, so don't allow it. This is one way of many to prevent resubmission of existing data.
A good way to prevent a refresh from resubmitting altogether is to do a redirect to a result page right after you deal with the POST request. When the user presses refresh then, he/she will refresh the redirect and not the form submit.

Tiger stops Internet - data exchange after indefinite time ...

Similar Messages

Maybe you are looking for