Time Capsule 2TB not backing up my MacBook Pro anymore

I'm having a bit of a problem with my Time Capsule.
I use this Time Capsule to backup my MacBook Pro only. So far it was working and backing up without a problem since September 1, 2010.
I didn't use my MacBook Pro on a daily basis as usual, just a few minutes just to check email and then power down, for two weeks, so no backup was taken and if during that time if I was using it and the backup started I cancel it.
Now three days ago, I decided it was time to let the backup finish as usual, but now I got an error message that my time machine disc wasn't available so the backup was delayed.
I tough that this was caused by a low connectivity or a WIFI interference, so I decided to take it and connect it directly to the Time Capsule via Ethernet.
I started a backup, but after a few MB copied, the backup seems to stall, nothing gets copied and I get the SBBOD. So I forced the control panel to close and started again, same result.
Rebooted the computer, try again, copied a little more and then stops, the blinking light stops and now the computer freezes.
I deactivated Time Machine, re activate same result.
Found some links on the net, try the suggestions, no luck.
So I decided to erase my Time Machine, and nothing changed, still stops sometimes after a few MB, other times after 1Go of Data, the max I got was 2,5Go, then the system freezes, I have to hard boot my mac.
I decided to try with an external HD connected to my MacBook Pro via FireWire 400 and it did a complete backup of my mac (100GB) without a problem and no frozen mac.
I tried again on the hard drive on the Time Capsule, and again the mac froze and I got just 2GO of data to be backed up.
This is not working either via Wi-Fi or Wired connection. The result is the same, frozen Mac after some data is backed up.
Before I erased the Time Machine drive, I mounted the .sparcebundle drive and did a repair and no error were detected.
Since my Time Capsule is no longer under warranty, I open it, and connected the drive to my Mac Pro via USB SATA adapter and started a drive diagnose with disk utility, an error were detected with the drive and I applied the repair. Formatted the drive and put it back into the Time Capsule.
Tried again to do a full backup of my MacBook Pro but same result, the computer froze, no backup was done.
I started a new backup of my Mac Pro into the Time Capsule and via Ethernet and so far still backing up (a lot of data 300GB and still going) without any problem or a hang or frozen computer. I decided not to stop this backup not to corrupt anything on my Mac Pro.
I don't know what to do, I know for sure that it is not the Time Capsule, it's something on the MacBook Pro but what? A bad configuration, somewhere on my MacBook Pro.
I'm new into Macs and my knowledge of debugging mac is very small. I don't know what to look for and where. And certainly I don't want to erase my MacBook Pro Hard Drive or clean install Snow Leopard.
Does anybody have a clue of what this may be.
What should I do to clean any reference on my MacBook Pro to this time capsule and start all over again? I don't know what to do.
Thank you for your help.

I think I found the culprit!!! Yes I know it's basic to check, but once you're headed in a direction you forgot about all the rest. We're all humans after all.
But maybe my error will help other not to repeat or made the same mistake I did.
I deactivated Sophos Anti-Virus and I added my Time Capsule to the Exclusion List.
So far I passed the 2.5GB of data copied that always made my mac freeze.
Going to 13.50GB and still going, I'll check post an update if everything completes in a normal way.
Thanks to Jolly Giant and Pondini for their help.
Check next post for updates.

Similar Messages

  • My time capsule is not backing up my macbook.  Password issue.  My other mac mini connected wirelessly works fine and backsup correctly.

    My Time capsule is is backing up my Mac Mini just fine, however, my Macbook keeps asking me for the password and it does not like any of the passwords I use.  I have since used a pen to reset my Time Capsule and it reset all the network passwords for all 11 devices I had linked to it, however, it did not resolve the issue of my backup issue.  Ironically, the macbook still connects wirelessly with my macbook so I can surf the web with it, however, it does not backup on that same device because it must have a different password... Not sure what to do since my Mac Mini is backing up successfully.  I must have chosen a different password and it saved to that device, is there a way to display the Time Capsule password on my mac mini so I can attemp to use that on my macbook?

    What is the current setting of the TC disk access? It has three main levels, device password, disk password and user names and passwords. If you have it set to the last you will need to create a new username and password for the MacBook or recover what you were using.
    Have you ever done a backup to the TC via the MacBook?
    What OS does it run?
    The default password if you did not set anything is public.
    Try manually mounting the TC disk on the MacBook and see if that allows TM to find it.
    There is a lot of useful setup and troubleshooting info here.
    http://pondini.org/TM/Troubleshooting.html
    I would install the widget.. A1 and do a full reset of TM in the laptop, A4. As well as verify if you have already done a backup.. A5.
    Basic setup of TC for TM is explained here.
    http://pondini.org/TM/Time_Capsule.html
    Recovery of passwords is possible but should not be necessary.
    See info here.
    https://discussions.apple.com/docs/DOC-3372

  • New Time Capsule will not back up my 2009 MacBook Pro. I can see and find my last back before Mavericks but cannot backup.

    New Time Capsule will not back up my 2009 MacBook Pro. I can see and find my last back before Mavericks but cannot backup. The TC will not allow me to delete or start a new backup disk. My 2024 MacBook Air did the same yesterday but today it backs up.

    Seems to be working now. I left the MacBook on all morning trying to back up and now works.

  • Every time I try to back up my Macbook Pro with an external hard drive using Time Machine, I receive the error of "the disk does not have enough space". I have a 500GB hard drive and only 120GB Macbook. It worked fine before the latest Maverick's

    Every time I try to back up my Macbook Pro with an external hard drive using Time Machine, I receive the error of "the disk does not have enough space". I have a 500GB external hard drive and only 120GB Macbook. It worked fine before the latest Maverick's update. Any help would be greatly appreciated.

    My guess would be it has created an entirely new backup of your drive when you upgraded to Mavericks.
    See Here: http://pondini.org/TM/1.html
    And here: http://pondini.org/TM/9.html
    Peruse the whole site. There is a lot of information there.

  • I'm receiving an error message that reads "The backup disk image '/Volumes/Data/my name's iMAC.sparesebundle" is already in use.  The time capsule is not backing up any files.

    I'm receiving this error message about my Time Capsule:
    "The backup disk image '/Volumes/Data/my name's iMAC.sparesebundle" is already in use.  The time capsule is not backing up any files.

    1. Open the Sharing preference pane and check that the computer name hasn't changed without your knowledge. For example, if the name was "X's iMac," it might now be "X's iMac (2)". In that case, restore the original name. You may have to click the lock icon in the lower left corner of the preference pane to unlock the settings. Test. If there's no improvement, or if the name had not been changed, continue.
    2. If you're backing up to a Time Capsule, or an AirDisk attached to a 2013 or later model AirPort Extreme base station, restart it in either of the following ways:
    ☞ Disconnect and reconnect the power adapter.
    ☞ Select the device in the AirPort Utility application and then select
              Base Station ▹ Restart
    from the menu bar.
    If AirPort Utility notifies you of a firmware update, install it.

  • Time Capsule will not back up address book

    Fior some reason Time Capsule will not back up my address book. When I delete an address and start up Time Machine, it will show my address book screen. However all my "older" address book screens in time machine are blank. I have searched various forums but have not been able to find other topics on this issue. Is here anybody who has a clue (the address book is not exempted for back up)?

    I just checked to see if TM was backing up my address book, and at first I saw the same thing you're describing, but after a minute or so, old backups appeared. Have you waited a minute to see what happens?

  • Time capsule will not back up any more

    My Time Capsule will not back up anymore. I have a message stating there is not enough storage room. I have the setting to delete the oldest backup to make room for the newest backup. Any suggestions?

    When you upgrade the OS, it produces massive backups. Mavericks in particular has produced all kinds of issues for people.
    You have several choices..
    1. If nothing in the backup is important to you.. erase the TC and start over. That is the easiest.
    2. If you want to keep the old backups then archive the existing sparsebundle to USB drive plugged into the TC.
    Then erase the disk and start over. That is good way as once TM has established its routine.. and you are certain nothing in the old backups is needed you can wipe the USB.. after 6months or 1year or whatever.
    3. Plug the USB into the TC and use that as the target and start a new TM backup.
    4. Plug the USB into the computer and use that as the target for TM.
    5. Delete older backups in the sparsebundle yourself. I place this last, as it is the worst option IMHO.
    http://pondini.org/TM/12.html

  • Time capsule will not back up/sparse bundle is already in use?

    Time capsule will not back up/sparse bundle is already in use?

    Thank you.  After reading more, I turned off time capsule in system preferences, shut down computer, unpluged and pluged back in time capsule.  Turned computer back on and the problem went away and time capsule successfully backed up.
    There is an old rule in boht PC and MAC world, try reboot first, ask later.  I often forget it.
    Thanks again.
    Quarto

  • Can I use the new Time Capsule to backup my mid 2010 Macbook Pro? Also can I want to free up my hard disk, can I save my photos and files on the time capsule and later access through wifi?

    Can I use the new Time Capsule to backup my mid 2010 Macbook Pro? Also can I want to free up my hard disk, can I save my photos and files on the time capsule and later access through wifi?

    Can I use the new Time Capsule to backup my mid 2010 Macbook Pro?
    Yes, if you are asking about using Time Machine to backup the Mac.
    Also can I want to free up my hard disk, can I save my photos and files on the time capsule and later access through wifi?
    You are not thinking of deleting the photos and files on your Mac, are you?  If you do this, you will have no backups for those files.
    Another concern is that Time Machine backs up the changes on your Mac. At some point, Time Machine will automatically delete the photos and files from the Time Capsule.....you just don't know when this might occur.
    In other words, only delete files from your Mac that you can afford to lose.

  • TS1550 My time capsule will not back up. There is a time machine error message that states "The backup disk image "/volumes/Backup/Jane's MacBook Pro.sparsebundle" is already in use. How do I correct this problem?

    My time machine will not back up. I get a Time Machine Error message that reads: "The backup disk image "/Volumes/Backup/(myname)'sMacBook Pro.sparsebundle" is already in use.
    I have not been able to back up for two weeks, I think this occurred after an update to the operating system, but I am unsure.
    How do I correct this problem?

    Have you tried restarting the computer? Also, see Time Machine Error from this pages sidebar under More Like This.

  • Time capsule will not back up my iMac since I replaced the hard drive

    I replaced the hard drive in my iMac, now time machine won't back up to time capsule because there is not enough space. I believe time machine/time capsule thinks the new hard drive is a new computer and therefore must perform a new complete backup even though the data on the new hard drive came directly off the old hard drive (the was backed up on time capsule. Our time capsule is currently backing up two computers (both Macs). How do I get time capsule to start backing up the new hard drive?

    You'll have to be more specific -- that's like emailing an auto mechanic saying only "My car won't start."
    Has it ever worked?
    Does your Mac recognize your Time Capsule?
    Do backups start?
    If so, do they hang, or fail?  If they fail, with what message?
    Start with Time Machine - Troubleshooting.   It will show you how to locate the message(s) that describe the problem, then help you fix it.    If that doesn't help, post back with details, including all the messages, your setup, what you've done, and the results.

  • Receiving an error message and time capsule will not back up!!

    I am getting this error message, The backup disk image “/Volumes/Nikki Worstell1's Time Caps MacBook Pro.sparsebundle” could not be accessed (error -1).  Right now I cannot back up on my time capsule.  Any suggestions??

    See # C17 in this excellent support document by Time Machine wizard Pondini.
    http://pondini.org/TM/Troubleshooting.html

  • I have a shared time capsule but it says on my Macbook Pro that it is not connected, though it is on the shared computer OK?

    My time capsule is a shared one with my husband's iMAC. His is connected but my Macbook Pro, says I am not connected. Has anyone any ideas please?

    Learner73 wrote:
    I have been upstairs to look at the cables. This is what I found:-
    on the capsule there is a cable in the Power port Then an empty port Then the ethernet cable Then 2 empty ehthernet ports. On the Hub ..... ADSL cable, then a Red BT Infinity port (empty) .... Then the Ethernet cable from the TC. Then 2 empty yellow ports, Then the power cable.
    I am fairly clear.. please do what I suggested.. take the computer upstairs and plug it into TC with an ethernet cable.
    Then you should get internet and airport utility will see the TC and we can work out the issues.
    Does the BT hub still have its wireless working??
    Hope you have a safe trip to get supplies.. it is 39deg in our area of Melbourne tomorrow.. a bit of ice and snow sounds nice.. but I am glad it doesn't.

  • Help Help..Can not back up my Macbook Pro with Time Machine

    I have Mac Book Pro Mac OS X version 10.6.8 and Time capsule 802.11n (3rd generation), I used to do back up wirelessly but then it stopped. so i connected it directly to laptop, it did not work. so i did reset on Time Capsule/Machine and didnt work. Show error 1) Time Machine could not comple Back Up (The back disk image "/volume/data/macintosh.sparsebundle"could not be created (error 1) and then different time i tried got different error 2) Time Machine Could Not Complete (the back disk image "/volume/data/macintosh.sparsebundle"couldnot be created (error 60)..please advise

    The TC drive is network and will never show up in disk utility.
    You can mount the sparse bundle into the utility and do a check on it.. but that serves little purpose.
    I used to do back up wirelessly but then it stopped. so i connected it directly to laptop,
    It is highly likely the setup is wrong.
    Please do a full factory reset of the TC.
    The Factory Reset TC Gen1-4. Or AE Gen1-5
    Unplug your TC/AE. Hold in reset. and power the TC/AE back on..  all without releasing reset and keep holding in for about 10sec.
    Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
    Be Gentle! Feel the switch click on. It has a positive feel..  add no more pressure after that.
    TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
    No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
    Redo the setup using the airport utility. For older OS and TC you can do this by ethernet with wireless turned off if you like.
    Tell us the main modem router and how the TC was originally setup.. if it was in bridge mode.. then put the TC back in bridge and plug it into the router.
    If there are issues they will show up in the airport utility. Please list any issues it has.

  • Time capsule as time machine to automatically back up my macbook pro?

    I had been using an Airport Supreme router with a 2 Tb time capsule as an auxiliary port to the internet.  Now the Airport Supreme is no longer available and I want to use only the Time Capsule.  It works perfectly as a router but does not allow automatic time machine backups.  There must be some switch somewhere to make it be the primary unit.  Please give me a clue.  Thank you, Tommy

    The TC will need to be factory reset and redo the setup so it takes over the role of main router. You cannot just switch something..
    The Factory Reset universal
    Unplug your TC/AE. Hold in reset. and power the TC/AE back on..  all without releasing reset and keep holding in for about 10sec. The time is not important.. it is the front LED rapid flashing that indicates you are in factory mode.
    Release reset.
    If it doesn’t flash rapidly you have released reset at some point and try again.
    Be Gentle! Feel the switch click on. It has a positive feel..  add no more pressure after that.
    TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
    No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
    Depending on the kind of network you should have no problems with this.. it does not delete files.. just to repeat.. your TM backups will be fine.
    I do strongly recommend in the new setup you use all SMB naming.. that is because Apple is now changing over from AFP as default protocol to SMB.. and it has tighter rules.. so don't worry if that makes no sense.. the rules are simple.
    1. Short.. keep names below 20 characters.. 10 is good..
    2. No spaces in names.
    3. Pure alphanumeric.. no apostrophe.
    Once you setup the TC then you can redo the setup of TM to find the TC.
    Note also IPv6 is now essential to the operation of the network.. please ensure you set it to link-local only in the network client/s on the computer.
    eg wireless.

Maybe you are looking for

  • Keyboard shortcuts no longer working on 10.5 in Firefox and Photoshop

    We developed an Inuttitut keyboard layout for Mac OS X 10.4 and above (Inuttitut is the language of the Inuit in Nunavik, the most northerly region of Québec province in Canada). For information, our layout allows to type in Unicode whenever Caps Loc

  • Contacts Calendars Bookmarks Find My iPhone toggle buttons won't switch on

    I have a new iPhone 3GS, but under Settings - Mail Contacts Calendars - My .Mac account, I cannot get the toggle buttons for Contacts, Calendars, Bookmarks and more importantly Find My iPhone, to switch to 'ON'. Mail however is 'ON'. When I click the

  • Installation of Solaris 10 over HP server having SCSI disk

    Hi, i have "HP ProLiant DL145 G2 Server" having 2 SCSI hard drives each 72 GB. But when i m installing solaris 10, then during parttion time, it is showing 17 GB for one hdd & 35 GB for other. But i want 72 GB for parttioning. I also conformed that n

  • Issue with Adobe PDF Ifilter Extension version 11

    Dear Friends Come across few issues while determining correct version of Adobe PDF Ifilter Extension In my local laptop I installed Ifilter extension 9.0 but unfortunately this version is no longer available for further download. Latest version is 11

  • Withholding tax not considered on clearing

    Hi dear SAP colleagues, Problem: SAP does not retain the value related to withholding tax In this scenario, withholding taxes are charged on values since 7.000 Company acquired equipment for 14.000 and in may 17 posted and advance of 13.000. In june