Time Capsule - Airport Express - Airport Express Remote Speakers Fail

Like my title mentions, my configuration is:
-Time Capsule on 3rd Floor
-Airport Express on 2nd Floor
-Airport Express on 1st Floor
The distance is not that much between each component and the Airport Express are all green and show up as working on my Airport Utility.
In order to extend my network, I have created a WDS network, Internet works like a charm anywhere in the house.
In the first floor, I hook up my speakers to the Airport Express. In iTunes, the AE shows up and when I select to output sound to the speakers, it briefly plays the music for a second and then it plays no more.
If I take the AE for the 1st floor and plug it in the kitchen wall on the 3rd floor, the music sounds through the speakers without a problem.
What can be causing the AE to fail to play to the music on the 1st floor? Everything is green and working, I am baffled.
Thanks!

Mitchell, welcome to the discussions!
You may find it easier to use Manual Setup in AirPort Utility for the device.
The key setting would be under the Internet icon. Look at the bottom of the pane for Connection Sharing, this would be set to Off (Bridge Mode). Under the Wireless tab, you would set the Wireless Mode for "extend a wireless network" and make sure there is a check mark next to "allow wireless clients"
On the setup of the Time Capsule in AirPort Utility - Manual Setup - Wireless tab, make sure there is a check mark next to "allow the network to be extended"
If you have a good wireless signal in the area where the Express will be located, you also might want to try extending your network without using the ethernet cable. Normally, a good starting point for positioning the Express is at a point that is approximately half the distance from the Time Capsule and the area that you want to cover with the Express.
You may also need to reset your cable modem by powering it down for 10-15 minutes and then restarting.
Please post back on your progress.

Similar Messages

  • I have a "n" time capsule and "g" airport express

    Hi, I'm trying to extend the range of my Airport Time Capsule (1st generation "n").  I have a "g" Airport Express and I've been trying to set it up as a remote base station (or do I mean "relay"?) to strengthen the signal in a distant room.  It's not working!  Is the problem that you can't use a "g" express with an "n" Time Capsule???  Do I need to buy an "n" Express, or is there something I'm doing wrong? 

    I'd suggest reading the Designing Airport Networks manual. There is a section on setting up a WDS with a Time Capsule and an Airport Express.

  • How can I set up a wi-fi network, using one time capsule and two airport express

    how can I set up a wi-fi network, using one time capsule and two airport express ?
    The time capsule is near the Mac. ok
    The first Airport is on the corridor, ok, works well and the App on the iPad signals so, ok
    But when I plug the next Airport on another room nearby nothing happens, and signals disconected ....
    is the signal so weak that is not able to go to ono room to the other ?

    Well, even if you have the first express set up to extend the network, the second express can only extend from the TimeCapsule.
    Maybe you got walls of sheetrook in the way, or kitchen/bathroom tiles, etc, dampening the signal rapidly.

  • I have a airport time capsule, an older airport extreme, and an airport express.  I want to hard wire my Mac Mini to the network.  What is the best arrangement of the devices?  which ones should be hard wired to optimize extending the network?

    I have a airport time capsule, an older airport extreme, and an older airport express.  I want to hard wire my Mac Mini to the network.  What is the best arrangement of the devices?  which ones should be hard wired to optimize extending the network?

    I am using TM Unifi with an ASUS RT-N18U Wi-Fi router.  I would like to know could I use Apple AirPort Time Capsule to extend (repeater, booster) my Wi-Fi to a part of the house where the Wi-Fi signal is poor
    Yes,, if you plan to connect the AirPort Time Capsule to the ASUS router using an Ethernet cable connection that will remain fixed and permanently installed at all times.
    No, if you were planning to have the AirPort Time Capsule connect wirelessly and extend the Asus WiFi signal, since it would not be compatible with another manufacturer's router for that purpose.
    Another way of saying the same thing here would be that if you want to extend the network wirelessly, it will take two Apple routers to do so

  • What is the maximum distance between a time capsule and an airport express?

    What is the maximum distance between a time capsule and an airport express?

    You can only "extend" the signal one time, so you need to have the AirPort Express located approximately 1/2 to 2/3 of the distance from the Time Capsule to the area that needs more wireless coverage.
    I doubt that this will help much since you have a very challenging setup. Wireless is really only for "same room" or "nearby rooms" around the corner.
    To do this correctly you will need to use an Ethernet cable connection from the Time Capsule to the AirPort Express, which could then be located close to the xBox.
    If it is not possible to run the Ethernet cable, you might look at a pair of Ethernet powerline adapters to send a "psuedo" Ethernet signal over the AC wiring in your home.
    This will not be anywhere near the performance of a regular Ethernet cable, but it will likely be much better than wireless.
    Since Ethernet over powerline (EOP) is somewhat unpredictable, you would want to have a very clear understanding of the store's return policy in case things don't work out as hoped.  Any computer / electronics superstore will have a selection of powerline adapters to choose from.

  • Time Capsule vs. Airport Express via Ethernet

    Air;ort Express is connected to a DSL modem with an Ethernet cable. Time Machine is in turn connected directly to my MacBook Pro, again by Ethernet. Obviously something here is wrong, since the Time Machine persist in showing a blinking yellow light.
    I think that this used to work but no longer. How did I sdrew up?

    Does that in turn suggest that I should connect the Time Capsule directly to Airport Express?
    when possible always run ethernet.. it is fast and reliable.. only when there is no other choice use wireless to link routers.. it is always poor.
    You can use wireless from laptop to the Express or the TC.. that is fine.. but keep the wireless usage to something close and just once.. no double hop over wireless.
    If you have ethernet there, use it.
    Simply put the TC in bridge mode.. that is router bridge.
    And make sure you are creating a wireless network on the TC.. same name and same security setting and password as the Express.. then the laptop can connect to whichever it is nearest to.
    If you need complete diagrams or screenshots just ask.
    life is a lot more complicated than it was when I bought my first 128K Mac in 1984.
    Not always.. networking with modems and telephone wires was not always fun.. !!
    You forget what it was like 30years ago.. !!
    I started about that time but could never afford Macs. When I think of all the money I spent on computer gear over the years it is frightening.
    Instructions here for roaming network since Apple has none up to date.
    Setting Up Roaming - New AirPort Extremes and Utility

  • Force 802.11ac Connection To Time Capsule Rather Than Airport Express

    I have a new Time Capsule and a new retina Macbook Pro, both with 802.11ac.
    The Time Capsule is in my main room and my rMBP is in my offce.  In between my office is the kitchen which has an Airport Express.  The reason I have the Airport Express in the kitchen is because some devices such as iPads and iPhones have a hard time connecting to the Time Capsule, so the Airport Express extends the network.
    The rMBP has no such problems.  However, because the AE is closer, it stays connected to the AE rather than the TC.  This of course means I don't get any 802.11ac advantages.
    How can I force the rMBP to connect to the TC and ignore the AE?

    LaPastenague had good advice for you. All that you need to do is use AirPort Utility to enable the option to assign a different name to the 5 GHz band on the Time Capsule.
    Then, move your MBP close to the Time Capsule and "point" your MBP to that network.  Then, check to insure that you have the MBP configured to connect to the 5 GHz network first in the connection priority list.
    Open System Preferences (gear icon on the dock)
    Open Network
    Click on WiFi on the left
    Click Advanced at the lower right
    Make sure that the 5 GHz network name is at the top of the connection order list. If it's not, drag it there
    Make sure that there is a check mark in the box next to "Remember networks this computer has joined"
    No other boxes should be checked
    Click OK
    Click Apply
    Close the windows
    Note.....As you know, 5 GHz  signals are much weaker than 2.4 GHz signals, so 5 GHz works best when wireless devices are in the same room, close proximity, or have line of sight with each other.  If there are several walls or other obstructions in the signal path between the Time Capsule and MBP, the Mac may not connect at high speeds.

  • Can I link up one time capsule with two airport express, Can I link up one time capsule with two airport express

    Hi, I would like to know whether I can link up one time capsule with two airport express. The result why is that I would like to put one time capsule at first floor, two airport express at 2nd floor and 3rd floor. All these three share one network. Please advise. Thanks.

    There are several ways to conenct them. We need to know what it is you want to accomplish first. Do you want better Wi-Fi coverage on the second and third floors or do you want to stream music to the xpresses?

  • Time Capsule green and Airport Express blinking amber

    I replaced my AEBX with a Time Capsule and now the AEX configured as an extender blinks amber continuously. Bringing up AirPort Utility and following the AU help instructions to find out why the blinking amber, shows that the AEX is operating normally. In fact, the little faux LED to the left of the AEX icon shows green while the real LED is blinking amber.
    The AEX was solid green before installing the TC.
    Anyone else seen this? Anyone know what's going on?

    I cannot get Airport Utility to see both my Time Capsule and my Airport Express at the same time. When I disconnected from the Time Capsule network it saw the AEx but repeatedly said there was a problem configuring the device. So I am stuck.

  • Time Capsule with (2) AirPort Express connection problem

    I have (1) Airport Time Capsule with (1) AirPort Express connected. I'm trying to connect another Airport Express but only get a yellow light on the 2nd Express. If I connect it with a ethernet cable I get a green light. How do I connect a 2nd Express?

    The 2nd Express needs to be about the same distance from the Time Capsule as the 1st Express....and....it cannot be closer to the 2nd Express than it is to the Time Capsule.
    The reason for this is that the Express will pick up the strongest signal and you want the Express to pick up the Time Capsule signal to be able to extend it.
    Then, start over as LaPastenague instructs on the 2nd Express and configure it again.

  • Time Capsule disappears from Airport Utility, need to restart to find it.

    I got a new Time Capsule for Christmas. Our household was using a D-Link router. The network was working fine for a Macbook, iMac, 2 x iPhones, PC Laptop and desktop. The two laptops are upstairs and connect wirelessly to the Time Capsule and an airport Express connected to stereo is set to extend the network.
    Since Christmas the laptops are losing contact with the Time Capsule. At first I'd physically disconnect the modem and TC and the TC would reappear. Finding this annoying I rang Apple. I was told to edit locations in networks, add a location and basically reselect my network. I was told to monitor this, but that it should help. The TC went off airport utility again (the green light was still on), so i went through the process of edit location again and it worked. I posted the problem in macbook internet, thinking it was a macbook issue as my iPhone could still connect to the network and have internet. People suggested i do a power cycle. The next time the network crashed I performed a power cycle on every item connected to the network and turned on in correct order.
    Tonight my macbook and pc laptop lost connection with the internet again. I had to physically take the TC and modem of power to get the network back again.
    This is happening every couple of days, and I'm now sure it's a Time Capsule issue, this issue didn't happen with my D-Link router. I have my Macbook completing Time Machine Backups wirelessly, and when we lose connection with the TC, backups are delayed. Could the Time Machine backups be causing this loss of connection?
    I'm going to call Apple and see if they have another solution, but was checking to see if others have had this problem and maybe a solution?

    I just purchased a new Airport Time Capsule 3TB (ME 182 AM/A)
    I broke my own rules.. as I saw one going really cheap and our currency is dropping like crazy so i thought I better get one .. stupid idea.. it lasted less than week and then refused to even power on.. It has gone back for replacement.
    For your situation I think the problem is not the TC as much as it is yosemite.. but it is the combo.
    Try the things I have suggested in this thread.. they have worked or helped other people.
    Time Capsule keeps losing connectivity

  • Can I backup to a time capsule via an airport extreme.

    I have a time capsule although it is at the other side of my house and i dont get great signal. I am looking at getting an airport extreme (would an airport expres to extend my signal. Will i be able to backup to my time capsule via my airport extreme.

    If your Time Capsule was purchased in the last few years, chances are you have a simultaneous dual band Time Capsule.
    In order to extend both bands using wireless only, you would need a new AirPort Extreme, since the AirPort Express would only be able to extend one band from the Time Capsule.
    If you only need to have one band extended, then an AirPort Express would likely work for your application.
    Whether you choose the Extreme or Express, keep in mind that the correct location for an extending device is a point that is approximately half the distance from the Time Capsule and the general area that needs more wireless coverage.
    Apple's instructions to configure the "Extend" setup are here. Although an AirPort Extreme is pictured in the example, the instructions for an AirPort Express would be the same.
    http://support.apple.com/kb/HT4259

  • How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

    How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

    The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
    If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

  • HT3728 Firmware Update 7.6.4 Error: I uploaded the 7.6.4 firmware update today, and received an error message as it was finalising. As I am using my Time Capsule as the Airport router, I am now no longer able to access it to try to resolve the problem. He

    Dear Support Team,
    I agreed to the Time Capsule 7.6.4 update today, but as it was completing, I received an error. It said to close the page and try again.
    I use my Time Capsule as my Airport wireless router and now can't access the Time Capsule to re-upload the Firmware update.
    Has anyone else had this happen?
    Is there a way to resolve the problem?
    Do I need to hardwire the Time Capsule? Then what?
    Would really appreciate some help!!
    Thanks everyone.

    Factory reset the TC and it should come back to life.
    The Factory Reset.
    Power down the TC.
    Hold in reset. and keep holding it in. Be Gentle! It is a tiny surface mount switch with a plastic lever.. Attempting to push it out the other side of the TC will not make the switch turn on better.
    (I fix TC and have several reset levers bent over and jammed or broken off).
    Power on the TC.. remember with the reset held in.. this needs three arms.. a friend or power switch you can get to with your feet..
    Keep holding in reset for about 10sec until the front LED flashes rapidly.
    Release reset and wait .. the boot will be slow as it deletes previous setting.. only from router side and pulls out the factory defaults. No files are deleted on the hard disk.. but the name of the TC may change.
    As a rule .. wireless is not reliable enough for mission critical work like firmware upgrades.. (Heck I don't think it is reliable enough for backups).
    Apple doesn't insist on wired connections.. some other manufacturers do.. and post warnings not to attempt it over wireless. Warnings inevitably read after the failed firmware update btw.. so perhaps Apple have decided to just save themselves the hassle.
    I believe it is just good practice to use ethernet for any time that sitting on a branch.. whilst sawing it off (ie failure will kill any future access).. means you always use ethernet for any setting up of a wireless router.. but you see I am old.. with grey/white hair.. and too many dead modems and routers around me.

  • How do you extend the guest network on a time capsule to an apple express?

    I have a time capsule in my main house with a password protected guest network i set up an apple express in the guest house to extend the networks. Unfortunately the guest house / apple express is only amplifying the main house network. I would like my tenant to join the guest network from apple express. Is that possible?
    How do you extend the guest network on a time capsule to an apple express?

    I would like my tenant to join the guest network from apple express. Is that possible?
    Sorry, but Apple does not allow the Guest Network to be extended in any way.

  • Can Time Capsule backup an Airport Extreme's attached USB hard drive?

    Can Time Capsule backup an Airport Extreme's attached USB hard drive (without currently being attached to a MAC OSX LION system)?

    No, sorry.. there is no way for the TC to see the files.. and even if you plug the hard disk into the TC there is no mechanism in the TC to drag the files to itself.. The TC is absolutely a dumb network attached drive.. everything you want to do must be done from a computer.

Maybe you are looking for

  • Multiple versions of the same JDBC driver - OK ?

    Hello We are using SJSAS 8.1 on our production server, it makes access to an Oracle database for user authentication and thus we have a copy of the Oracle thin driver ojdbc14.jar located in the directory. <sjsas_install>/lib Each of our web applicati

  • Stock control – hide if out of stock

    Hi, I'm trying to figure out the best way to go with a site I'm building. The client has hundreds of products and if a product is sold they want the item hidden from the website. The issue is – if I choose that option – hide if out and stock and most

  • Text too close to page number in TOC

    Most of the time I can take care of unattractive line breaks in the TOC by putting in non-breaking spaces in a paragraph. However, I sometimes have a situation where the text of a TOC entry is too close to the page number on the right. The text is so

  • VC table into function module

    Hi everybody, does anybody know if it is possible to push a table from VC to a function module ? As I know only one data row can be transfered. Best Regards, Murat Y.

  • WHERE rowID NOT IN (another recordset on same page?)

    Hi. I have a recordset that lists movie reviews.  On the same page, I have a menu that lists movies, for review. I want to hide movies, in that list, if they already exist in the users recordset of reviews. In other words, if the user has already sub