Time Capsule & Airport Express (AX keeps disconnecting)

Hello! I added an Airport Express (AX) to the mix in July of this year so that my blu-ray player could access the internet. Everything works fine most of the time but the AX will periodically not have a connection and be blinking Amber until I reboot it (at least twice I've literally had to connect my MacBook to the thing and completely reset it because a reboot did not work). Here's my setup:
The Time Capsule is connected directly to my cable modem. The TC was purchased April 2008. I use the WPA/WPA2 (TKIP) encryption level, have a closed network, and have set it up to be the Main for a WDS network. The AX is the Remote in the WDS network. The only thing I changed when I got the AX was configuring everything for a WDS network.
We have four computers (Mac Pro & iMac and two MacBooks) and two iPhones, all of which connect to the TC without issue (via ethernet and/or wireless). Both the TC and the AX are running the latest firmware and all four computers are running the latest versions of Snow Leopard.
After having to reset the AX several times, I've wondered if it has anything to do with the WPA group key timeout. Neither of the device's logs give me a clue as to why it won't stay connected but I've incremented the WPA group key timeout setting to 30 days (I've toggled it up and down over the last couple of months for testing purposes) and now the AX works fine for about 30 days or so and then I have to reboot it. I've also tried changing the channel.
Since it works fine during the interim, I don't believe there's an interference problem (there are no concrete walls or appliances between them).
Any ideas? Thank you!

Thanks for the reply!
I actually did set it all up with the "Wireless Mode" setting as "Participate in a WDS network" instead of extending it. I don't recall now why I went that route. Perhaps I had trouble getting the "extend a network" feature working (I remember it was a bear getting the two working together).
I checked and, yes, the AX is "n" capable. I also noticed the radio mode on both devices show only "802.11b/g compatible" as an option. Is this because of WDS?
Would you have quick instructions on how to just extend the network and still keep my security settings intact? The other issue I have yet to tackle is that bandwidth tests over the TC wireless show way slower download speeds than upload but ethernet is very fast (and we see the result in games like World of Warcraft). I don't remember this being the case before but I can't remember the last time I tested it. I know that speed will be impacted with higher encryption and the use of firewalls, etc., but it shouldn't be as slow as it is.
Thanks, again, for all your help!

Similar Messages

Best configuration to extend wifi with Time Capsule & Airport Express

In my house I have a Fritzbox wifi router on the ground floor as my primary internet access. I have an ethernet cable going to the 3rd floor study where the Fritzbox signal is relatively weak. I purchased a Time Capsule as a backup device, but also wanted to extend the Fritzbox wifi network by plugging the ethernet cable in to the TC. I was not successful in extending the network, so I had to create a new network. When moving from downstairs to upstairs, my iphone keeps the connection to the (now weak) wifi network and I have to manually change to the (stronger) TC wifi network.
Additionally, I used to be able to successfully extend the downstairs wifi using my Airport Express (and also managed to have my speakers plugged into this for wireless usage), but do not want to additionally complicate my set-up.
So, what is the best way to connect the following equipment, ideally with the same network name, to ensure I always use the strongrst signal automatically:
Third floor:          iMac,    Macbook,   Time Capsule, Airport Express
          Ethernet cable from ground floor to 3rd floor
Ground floor:     Fritzbox wifi connected to internet

You must configure the Bridge Mode setting as the very last step before you Update the settings, otherwise the setting will change automatically.
In other words, you can change the setting to Bridge Mode, but if you make any other changes before you click Update, the Bridge Mode setting will not take effect.
Or, if you see any error messages about DHCP conflicts or Double NAT....the AirPort is not in Bridge Mode...even though you might think it is. Check the settings again.
will I still be able to set up an additional 5GHz network in parallel?
Yes

Time Capsule-AirPort Express-WDS not working together

According to everything I've read here, I've configured this properly, but it doesn't seem to be working. If anyone can help me troubleshoot this I would greatly appreciate it.
I have a new Time Capsule acting as my main wireless base station; it has a manually-configured static IP address, is plugged into my Verizon FIOS router, and is set to distribute IP addresses over wireless using DHCP. I have it set to run a 5 GHz network in addition to the regular 2.4 GHz network. I have an older AirPort Express that I want to use to extend the range of the 2.4 GHz network (the Express can only do 802.11b/g, not 802.11n), in part because we have some older devices in the house that I don't want to slow down the 802.11n network, and in part because the 802.11b/g signal doesn't reach all parts of the house very strongly. So I told the Time Capsule to make its network extendable, told the AirPort Express to participate in a WDS network as a WDS relay, and entered the MAC address of the Time Capsule's 2.4GHz network as the WDS main. Result: flashing amber light on the AirPort Express, which no longer shows up in the AirPort Utility; I had to do a hard reset in order to get the Express back (and then it had to be reconfigured again, of course). At the moment I have it just joining my wireless network, and that works -- green light -- but of course doesn't allow the Express to extend the range of the wireless network.
What am I doing wrong here?

Before there was dual band, we always told users that if they used WDS, the entire network would revert to "g", even if the Time Capsule, AirPort Express, etc were capable of "n" performance.
Your findings seem to confirm that this happens with a dual band as well.
I think it's well worth it to get the AirPort Express 802.11n. Then you can reconfigure the Time Capsule back to "Create a wireless network" and check the box to "Allow this network to be extended"
The Express"n" would then be configured to "Extend a wireless network". I use this setup and would highly recommend it. There may be a slight bandwidth loss due to overhead, but the performance is light years ahead of WDS.
If you are using the same network name for both bands on the Time Capsule, then I believe by default the Express will extend the 2.4 GHz "n", "g" and "b" band. This makes sense for most users since 5 GHz signals do not travel well over distance or penetrate obstructions well.
IF...you want to extend the 5 GHz band, the only way that I know how to do this is click Wireless Network Options on the wireless setup page for the Time Capsule and enable the option to assign a different name for the 5 GHz network.
Then you will have to configure the Express to extend this specific 5 GHz network. I never had much luck extending 5 GHz, and I wanted my iPhone to be able to use the network across the house, so I went with the simpler one network name for both bands and extended the 2.4 GHz network.
If you have a "g" device joining the extended network, it may tend to slow the "n" devices down slightly...when the "g" device is active, but it won't drag everything down to "g" levels. When the "g" device is not active, "n" devices will run at "n" speeds.
BTW, the ethernet port on the AirPort Express is active when you configure it to "extend a wireless network". This can come in handy for hooking up DVD players, etc that need an internet connection for firmware updates and extra features.
Follow up....I tried a very quick reconfiguration of my dual band AirPort Extreme (same router that the Time Capsule users) and AirPort Express using the WDS arrangement and everything did indeed drop way down in speed and performance.
Post back if you have questions. Happy to help.
Message was edited by: Bob Timmons

Hi I've recenty purchased a new imac time capsule airport express. I've set up a new network, rather than extended the current one. How do I change my new network to an extended one or create an extended network?

Hi I've recenty purchased a new imac + time capsule + airport express.
I've set up a new network, rather than extended the current one. How do I change my new network to an extended one or create an extended network?
Michael

detailed in terms of what focus?
here is a video guide about using the airport utility
http://www.youtube.com/watch?v=65Jv6m43eIE

Time Capsule + Airport Express N How to extend

Have been trying to extend my wireless network but have been unsussessful. Here is my setup. Cable modem connected to Time Capsule and Express N connected via ethernet cable. I try to do it with the setup but it will eventually revert to picking up the cable modem IP address 169.etc so I think I might need to manually input the addresses. Will some walk me through this including the ip addresses I should use? The Time capsule is NOT in bridge mode and works perfectly with the internet and other expresses used only for music streaming. Thanks

Mitchell, welcome to the discussions!
You may find it easier to use Manual Setup in AirPort Utility for the device.
The key setting would be under the Internet icon. Look at the bottom of the pane for Connection Sharing, this would be set to Off (Bridge Mode). Under the Wireless tab, you would set the Wireless Mode for "extend a wireless network" and make sure there is a check mark next to "allow wireless clients"
On the setup of the Time Capsule in AirPort Utility - Manual Setup - Wireless tab, make sure there is a check mark next to "allow the network to be extended"
If you have a good wireless signal in the area where the Express will be located, you also might want to try extending your network without using the ethernet cable. Normally, a good starting point for positioning the Express is at a point that is approximately half the distance from the Time Capsule and the area that you want to cover with the Express.
You may also need to reset your cable modem by powering it down for 10-15 minutes and then restarting.
Please post back on your progress.

Need help setting up WiFi - Xfinity with Network Switch, Time Capsule, Airport Express and Apple TV

Hello - I recently got Comcast Xfinity service. We had switched from a different service. Our wifi service was never great, but prior to Xfinity, it worked decently. But now that we have Xfinity, our wifi is much worse and very unreliable. I am seeking advice on how to setup my various Apple wifi devices in my home. I have attached a diagram that illustrates what I am dealing with. We have a large old house with stone walls. Comcast does not support this issue.
To explain the attached diagram, we have a total of 4 levels in our house - an unfinished basement, 1st floor, 2nd floor, and 3rd floor. The Xfinity router is in the basement and it is connected to a NetGear 10/100 network switch. I already have ethernet cables running from the network switch in the basement to various locations throughout the house. So I have ethernet connected to my time capsule and ethernet connected to each of my 3 Airport express devices. The dark lines running from the network switch to the various devices represents ethernet cable.
The immediate problem that we are having is that we are unable to connect to our wifi networks. The networks show on my mac laptop and my iPhone, for example, but I am unable to connect. I know that I am inputting the correct password, but most of the time, we cannot get in. Sometimes we can..... Very frustrating! Also, due to the fact that I setup what I have over several years, I have multiple network names. I once tried to fix that issue, but was unable to tackle it due to my lack of understanding.
Here is what I am looking to accomplish:
1. Seamless wifi access throughout our house.
2. One name for our wifi network. Right now we have multiple names for multiple networks. Just want to simplify and have only one network. (I guess that an additional "guest network" would be ok, but not absolutely necessary.
Also, if you think I should disable the Xfinity wifi, and just rely on my mac wifi devices, I am perfectly fine with this. Just tell me how to do so.
I have no idea how where to start or how to set this up. I imagine that I would need to disconnect everything and reset and start from scratch? Can someone tell me what I should do? Even general advice would be helpful, but the more specific, the better, given my limited understanding. Any help or advice would be greatly appreciated.
Thanks in advance!

Your photo link is not working. Click on the camera icon to load an image. (Shorten the name of the file to something like WifiNetwork.jpg)
Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

How best to use TWO Time Capsules, Airport Express and Apple TV?

Hello
I have the following Apple equipment and am wondering how best to plug it all together. At the moment I am not using some items at all because I do not know how to best use!
1. MacBook Pro (2012 model) 'Mac1'
2. MacBook Pro (2009 model) 'Mac2'
3. MacBook Air (2011 model) 'Mac3'
4. Time Capsule 1TB (model A1355) 'TC1'
5. (another!) Time Capsule 1TB (model A1355) 'TC2'
6. Airport Express (2008 model)
7. Apple TV (2013 model)
8. LaCie 1TB USB Hard Drive
9. Apple iPhone
10. Sonos system
CURRENTLY
TC1 is plugged into the Virgin Media modem to provide a WiFi network called 'Amer's Apple Network' around the house. The Virgin Media wifi has been switched off to reduce interference.
TC2 is not being used. The Airport Express is plugged in upstairs (or sometimes near garden) to extend the 'Amer's Apple Network' and this seems to work fine.
Apple TV is plugged into main TV and is plugged into 'Amer's Apple Network' directly using Ethernet to TC1 but often runs slowly and does not work if Mac1 is not awake (or iTunes is not running on Mac1).
LaCie is plugged directly into TC1 and currently has a old copy of my iTunes library stored on it which my Sonos system access. However, there seems to be a problem in that iTunes randomly uses that LaCie library and/or local Mac library. Often we get a pop up message on Mac1 saying "Library cannot be found" and we have to manually navigate to the LaCie drive (via the TC1 folder) to open iTunes. Also connecting iPhone to Mac1 seems to work very slowly as it appears to be trying to back up to LaCie drive.
QUESTION
What would be the best, most efficient way of using all (or if some is redundant equipement then which), to set up the following:
1. A shared home network which enables all three computers (and any future Macs and/or iPads etc) to access one master shared iTunes library, which is the one that is updated with any new music, films etc added via any of those machines
2. A shared home network that enables a shared files folder but also allows each user to keep their own personal hard drive (eg locally on whichever machine they are using).
3. A fast (as possible) iTunes back up process when connecting iPhone to computer
4. Usage of both TC1 and TC2 (and Airport Express) to extend network around the house (several weak spots exist) and also to maximise storage using the 1TB of each TC1 and TC2.
5. Would it then also be possible to attach the LaCie USB drive for an additional 1TB storage? If so how and would it be very slow? From existing usage it appears to be very slow when used as a regular access drive, so perhaps better as a 'slow' drive that is just occassionaly used for back up and nothing else
Main question is (to the networking experts!), how would you personally set up all above to give best wifi coverage, fastest back ups, access to Sonos for iTune library, access to Apple TV, and shared folders etc etc. I basically seem to have lots of kit (albeit some quite old) and nothing seems to be working together particularly well.
Happy also to ditch any bottlenecks in the above equipment list (eg LaCie USB drive?) and add something which would better bring together the other components?
Any thoughts much appreciated!
Best
Amer

So ... FINALLY ... I found some time to implement this!
Steps taken and results:
1. Moved my entire music library to Mac1. Used the opportunity to also share my other Mac2 onto HomeShare and copy across any music files from Mac2 onto Mac1 that were not already there.
Result: Mac1 now holds my whole music library locally. Works incredibly fast whenever playing a track, adding a new track or updating info on existing track. Good!
2. LaPastenague's instructions for bridging TC1 with TC2 worked a dream. Only thing is they are basically next to each other as I don't have the energy (or cabling expertise) to install (cleanly) long runs of ethernet cable.
Result: Got a clear Wifi signal, not sure if any faster than before but I assume two TCs next to each other both sending out the same network signal can't be any worse than one. Main thing is that I have an extra 1Tb network drive (i.e. TC2) connected to TC1 which I can access from all my Macs now.
3. Copied the entire Mac1 Music library over to TC2 drive into the Data folder. This happened relatively quickly (I think!) ... but would welcome any comments on whether slower than expected, to highlight if I might be able to improve the connection. 12,000 songs in 2 hours, with Mac1 sending the files to TC2 wirelessly. I know I could probably have connected Mac1 to TC2 by ethernet cable to speed up, but I had run out of Ethernet cables by now!
Result: All my music (as of today anyway) now on Mac1 AND on TC2 in normal readable format (i.e. by Sonos and as a simple back-up that can just be carried around and copied anywhere in the event of loss of Mac1 drive
4. Set up TC2 Music Library in Data folder to be the networked music folder for Sonos using "\\TC2\Data" (ps. why doesn't Sonos allow a simple click and select option for choosing drive and instead force us to go back to the 80s and type in drive path which isn't always clear, especially on a Mac!)
Result: Sonos can access all my music (as of today anyway) on TC2 and no need for Mac1 or any other Mac to be open.
BUT: As you may have guessed, the issue with the above set up is that as soon as I buy a new song, it will get added to my Mac1 quickly and smoothly ... but the area where I really use my music (i.e. Sonos via TC2) will have the older music library.
QUESTION: Is there any way in which I can adjust the above set up, so that whenever I add new music to my Mac1 it also copies across to TC2? Don't mind if this is done slowly and later (eg in middle of night) but of course don't want to have to copy across manually each time. Would prefer it to just update newly added tracks regularly.

A Time Capsule, Airport Express and AT&T 2Wire walk into a bar...

Alas, I'm sure this question has been asked before, but my reserach keeps turning up separate answers. So I thought I'd turn to this forum for some advice. Ultimately I'm seeks suggestions on various ways to configure my network to allow easy backups, connection two rooms, and wirelessly print from anywhere.
I have a:
Time Capsule (dual band) - used for Time Machine backups
Airport Express (older)
and new 2Wire 3800HGV-B wireless modem/router from AT&T (for U-verse internet/TV)
My room configuration is:
Living room with TV, internet connected DVD player, and new AT&T 2Wire Wireless U-verse modem
Home office with 2 desktop comptuers (no wireless cards) and a USB printer.
Two roaming laptops which move around the rest of the house
The livingroom and the office can't be connected with a physical wire.
What I was hoping to do was setup my office with the Time Capsule in the office as a wired hub, and then use it as a wirelessly bridge to the 2Wire network. But as I understand it, a Time Capsule can't be used as a bridge to a non-Apple product. Please correct me if I'm wrong.
Alternately I could always get wireless cards for the desktop computers, but this leaves the printer.
I've read suggesitons of people who have used their TC as the primary router, disabling wireless on their AT&T 2Wire, and hooking the two together with ethernet. Others who just join the TC to the 2Wireness network. But really what I'm seeking is a way to join the two rooms.
Any thoughts? Am I asking the right questions or providing the right information?
Much thanks,
dana.

So I figured I'd go with an initial suggestion and attached my TC via ethernet to the 2Wire modem/router in my living room, and make the TC my primary wireless router.
Good plan
since both will be in the same room, I assume I need to disable wireless on the 2Wire
Correct
What kind of configuration do I need to do on the TC, or do I just following the wizard and select 'Extend existing network'?
You can follow the guided setup or I can give you a step by step manual setup. In either case, you will configure the TC to "Create a wireless network".
("Extend" is only used if the TC connects using wireless only....you will be using Ethernet from one of the LAN <-> ports on the 2-Wire to the WAN port (world icon) on the TC.
The guided setup will normally sense that the TC is connected to another router and suggest that the TC be configured in Bridge Mode, which is the correct setting. Otherwise, select the Bridge Mode option when it is presented.
Note....If you have a newer dual band TC, the Guest Network option cannot be enabled when the TC is configured in Bridge Mode. So, if you want a "Guest" network, maybe the 2-Wire could provide that service.
Should I attach this (via ethernet) to the TC or the 2Wire?
Pick a LAN <-> port on either one, your choice, whichever is easier
What should the AT&T DVR be connected to?
I'm not familiar with an AT&T DVR, but if it connects via Ethernet, you can connect to a LAN <-> port on either the 2-Wire or the TC
For printing, my plan is to attach the printer through USB to the Airport Express and then connect that wirelessly to the TC network (though my first attempt at this failed to connect).
Suggest that you get the TC up and working smoothly. Then tackle the Express.

Time Capsule Airport Express Best Configuration for Backups & Internet

I have Time Capsule as a main router connected to a cable modem downstairs, plus Airport Express (new with firmware upgrade 7.3.2) in my office upstairs to extend the network. Two things keep happening:
1. Backups work sometimes and sometimes not although I am connected to my WPS secured network
2. Frequently lose internet connection, as in every hour or so; alternately nice and fast, then none at all. Most of the time I have a SNR of about 37.
Is there some optimal configuration settings for TC and Airport Express that could reduce these occurrences? Is there, for example, something I need to do with the Access settings on one or both?
Thanks for any help.

Since it still looks like you will need to support 802.11g wireless clients (your iPhone), the best radio mode for the Time Capsule (TC) will be the default "802.11n (b/g compatible." Since this is running in the 2.4 GHz radio band, you can use iStumbler (or similar utility) to determine if there are other Wi-Fis in the area; find out what channels they are operating on; and try changing channels on your wireless network to see if this will help provide the best SNR.
1. Backups work sometimes and sometimes not although I am connected to my WPS secured network
Are you actually using a WPS, or did you mean WPA?
2. Frequently lose internet connection, as in every hour or so; alternately nice and fast, then none at all. Most of the time I have a SNR of about 37.
If directly connected to the TC by Ethernet do you still lose the Internet connection periodically? If so, how about when connected directly to the cable modem?

Fios Time Capsule Airport Express 101 Help Needed

I am trying to configure my network for the thirty-billionth time. I will start with my set-up, my goals and then my assumptions. If anyone has any thoughts, I am deeply appreciative.
Set-up
MI424WR-GEN2 router (802.11B/G/N; firmware: 20.10.7.5; henceforth "FR")
Time Capsule (First Generation 802.11N)
Two Airport Express (802.11N)
One Airport Express (802.11G)
All Airport Expresses are running 7.5.2
Right now here's how I have my network configured:
The TC and AEs are in bridge mode. The TC is connected to the FR by ethernet. Physically, the TC and FR are right next to each other. I have two wireless networks set up. One created by the FR which I have the radio set in "Compatibility Mode" , i.e., accepting 802.11B/G/N. The second wireless network generated by the TC, is set to 802.11N Only (5Gz).
Optimally, I'd like to have one wireless network, instead of two. I'm willing to ratchet down the 802.11N only to a more compatible setting to get down to one network.
Assumptions:
I cannot use my FR in bridging mode -- meaning it simply sends traffic to my TC which handles IP addressing, NAT, etc.
I cannot use my TC or AEs to extend my FR wireless network. And by "extend" I mean, use the boxes as signal boosters back to the FR. Physically, I have the ability, for instance, to move the TC from it current location to the master bedroom and connect it back to the FR via ethernet. In this case, I would like to be able to use the ethernet ports on the TC for some devices as well as use the wireless (single network preferablly) to boost the signal for some box-to-box applications I'm running as well as bandwidth intensive applications like Apple TV.
It is my understanding that it is impossible to extend a network with a TC or AE unless it is Airport network. It is possible to join a non-Airport network but I'm not sure what that buys you.
I am also under the assumption that the dual network configuration is impeding my ability to remotely connect to my iMac if it is running on the TC network which feeds back to the FR network.
I have read blogs that argue for simply shutting down the Fios radio and set the Fios router to bridge mode in essence and use the TC for all wireless. I have read blogs that suggest a plethora of different approaches.
I'm eager to figure this out and and promise to be responsive to questions and suggestions!
Thanks in advance,
JB

you're suggesting using both radios so both the FR and TC are broadcasting. if both devices are physically next to each other, is there any benefit in terms of range?
I must have misunderstood your earlier explantion about your desire to "extend" and thought that you were going to try to configure the TC to provide more wireless coverage for the FR network by locating the TC some distance from the FR router and connecting to it using a long Ethernet cable.
If you plan to leave the TC sitting next to the FR router, then there is obviously no benefit, range wise, and a probable wireless interference issue if both routers are broadcasting the same signals in close proximity.
The exception here would be if you plan to configure the TC as a 5 GHz band only while the FR provides that 2.4 GHz band. That type of setup is OK since both routers are broadcasting on different bands.
I remember reading somewhere that ActionTec doesn't play well with AE in WPA so I'll stick to WEP.
If you want to configure the TC to provide a 5 GHz band, you cannot use WEP security.....only WPA2 Personal or WPA/WPA2 Personal....will work with 5 GHz.
That means that the FR router must also be configured to use the same security settings. If it's not, then you will have two separate wireless networks with the same name and password, but different secuirty. That is bound to cause connection issues.
If you cannot match up the FR security to the TC, then it would be better to assign a different name to the 5 GHz network to keep things straight.
The other issue that you may face is if the TC is configured to provide 5 GHz, then that is what the AX"n" devices will try to extend. It's not easy to extend 5 GHz since the signals are quite a bit weaker than 2.4 GHz signals. You almost have to thave a line of sight relationship between the TC and AX devices for 5 GHz to be extended.
If you don't really need a dual band 2.4 GHz and 5 GHz network, then things would be a whole lot simpler if you turn off the wireless function on the FR router and setup the TC to provide a compatible "n/g/b" network, which the AX"n" devices will be able to extend.

Time Capsule & Airport Express Extended Network loses connection!

OK, so I am an Apple virgin of 2 months experience, after many many years with Windows based PCs, so please be patient and gentle with me. Sorry about the long explanation.....
My set-up comprises of a Time Capsule, which is connected to the Internet via a NetGear ASDL modem. Both pieces of equipment are situated in my wife's office on the first floor of our house. My office is on the ground floor, where I have a 27" iMac and an Airport Express which is connected to a printer via the USB port. The Airport Express is sited about 10 feet from the iMac.
All software and firmware are lastest versions - TC v7.5, AX v7.4.2 & Airport Utility v5.5.
For the past 2 months, I have only been using the AX to print wirelessly and the set-up has worked faultlessly.
Earlier this week, I decided change the configuration to extend the network to allow me to use my laptop & iPhone in areas of the ground floor where I had no signal. I followed the online instructions and first changed the TC to check the box to 'allow this network to be extended', after updating the configuration successfully I moved to the AX. Here I changed the wireless mode to 'Extend a wireless network', selected the network name and checked the 'Allow wireless clients' box. This also updated successfully.
Everything ran correctly and the range of the network was greatly increased.......great, job done...not!
After about 3 hours the iMac lost the connection and the TC disappeared from the Airport Utility pane and refused to reappear. I checked but also couldn't connect or see any network on the laptop or iPhone, so have dismissed a fault with the iMac. I finally got things back up after doing a power reset of the TC, but after a few hours same problem occurred, and occurred and occurred. By clicking the Airport Utility icon on the top right of the screen and following the prompts from 'no Internet connection', I can at least get things up and working without a power reset of the TC, but the connection still drops after 2-5 hours each time.
My first call to Apple Support led to a full reset and re-config of both the TC and AX, setting the extended network up as I had done originally. The only difference was an iMac reset (alt/cmd P&R on power up) and changing the 2.4Ghz channel from 1 to 11. This had no affect and the connection drop-out problem continued.
My second call to Apple Support led to me being passed to a Level 2 Techie, who first suggested that I tried disabling the Guest Network - tried it, and it made no difference. I was then told to try a WDS network, which whilst not losing connection, is slower and has less range than the original extended network and frankly sounds a cop-out.
Has anyone had a similar problem, anyone solved the problems, can anyone offer any help or advice please.. I'd appreciate any input....thanks.

Similar problem here. Cable Modem (Moto SB6120)->AEBS (802.11n dual-band)>AX (802.11n) for wireless connection to MacBook Pro running Mac OS X 10.6.2. AEBS configured as dual-band: 801.11a/n at 5GHZ and 801.11b/g/n at 2.4 GHZ. AX configured to wirelessly extend the AEBS 5GHz 802.11a/n network. I am able to run on the extended 5GHz network (via AX) for varying lengths of time, until the internet connection dies. When this occurs, I am able to switch over to the 2.4GHz network to get back online. Solution up until now has been to unplug the AX, then plug it back in. After the AX restarts, I am able to hop back onto its 5GHz signal and get to the internet. However, the internet connection on this band will drop again after some time.
I was on the phone with Apple Support twice in the past week to get this resolved, but no joy. Senior Advisor seemed to think that my AX was working properly, and that that the problem could be with my AEBS -- perhaps the 5GHz antenna might be bad in my AEBS? Seems odd to me, since both my AEBS and AX are less than 2 months old...
I just read the post from LocoDoc and decided to see if I could replicate the problem. Sure enough, when I am connected to the internet via my AX extended 5GHz network signal and a Time Machine backup starts, the internet connection quits. Only recourse is to restart the AX. Note that I do not experience this problem with Time Machine while connected wirelessly straight to the AEBS 5GHz signal. Only when I am connected to the "extended" signal via the AX.

Bt Home Hub (fibre optic) can it work with my Time Capsule & Airport Express?

I have just moved house after having no problems for years with my virgin cable I have now had to switch to Bt because cable is not available at my new address therefore I would like first and foremost to have my Time Capsule available to use as a hard drive, I am not too bothered about wi-fi as that comes from the bt hub, only thing is I am at a loss how the Time Capsule hard drive is not working. Also is there anyway the Bt Hub can connect/link to Time Capsule or even Airport Express.

Your TC can be used bridged to the BTHub.. and plugged in by Ethernet.
It is best to still use the TC wireless for the express to extend and you will find access easier.
Always best to start with a factory reset when you do this.. The TC remembers too much from its last configuration.

Need help with new Time Capsule/Airport express setup!

I just hooked up a 500g time capsule to replace an airport extreme, and now my airport utility on my MacbookPro Retina no longer recognizes the airport expresses I had on my network for airplay purposes. Can anyone help with this issue?

Instead of a switch you need a wireless router, because your modem will only assign one public ip address to the switch and that ip address will be forwarded to any one computer at a given time...You should replace the switch with a wireless router and it should resolve your concern...

Select Between Time Capsule & AirPort Express

I have an iMac which sits between my Time Capsule and Airport Express (Extending)
My iMac reverts to the extender and as such - data transfer to the TimeCapsule drive is very slow.
How can I force the Mac either in Windows7 /Mac OS X to use the TimeCapsule as they share the same SSID in extention.
Thanks.

Unfortortunately, there is no way to "force" a device to connect to a given access point.
The iMac will connect to the device that it thinks has the strongest signal.
You have a few options:
Move the iMac closer to the Time Capsule
Move the Time Capsule closer to the iMac
Move the AirPort Express further away from the iMac

Belkin Time Capsule Airport Express PLC

I allready have a modem router Belkin, a Time Capsule and an Airport Express. The problem i have is that i have a many meters from the Belking and Time Capsule to the saloon (Airport Express). Can i buy an PLC and use it with my network connection???

... Can i buy an PLC and use it with my network connection???
Yes, but be aware that some work, and some do not.
It is not a question of using your Belkin router with a Time Capsule and Extreme or not. The problem is that it is impossible to know whether PLC will work in any particular installation, because building wiring practices can vary so much. Its maximum propagation distance is also unpredictable, for the same reason.
All you can do is try it.

Time Capsule & Airport Express (AX keeps disconnecting)

Similar Messages

Maybe you are looking for