Time Capsule & Airport with a new modem WiFi

I have a MacBook Pro and a Time Capsule with Airport. I have a new modem from my Comcast Internet provider that has WiFi Built into it. If I use the modem for my WiFi, will my Time Capsule connect with my MacBook through the modem Wifi? And how can I know which Wifi will be the stronger?

Plug the TC into the new modem with a decent length ethernet cord.. a few meters..
Then simply setup roaming network.. so both the TC and the new modem will reinforce each other.. the setup is easy.. Bob at least says it is.. automagically from the new v6 utility.. but it is not hard to do manually either IMHO.
The basic rule is simple.
TC in bridge.
TC creates a wireless network. Same SSID.. ie wireless name Same security .. ie WPA2 AES = WPA2 Personal.. same password.
Voila there it is. although using different channels can be helpful.. if you run into problem.
Now you don't have to worry about which is stronger.. the MB will connect to whichever is stronger.. without human intervention.
Ask Bob to elaborate..
https://discussions.apple.com/thread/5146401?tstart=0
BTW the roaming network document is a help.
http://support.apple.com/kb/HT4260
The fact that you have one apple and one non-apple router here makes no difference except in terminology.

Similar Messages

Time Capsule shows with wrong name on Time Machine

I changed the name of my Time Capsule using airport. However, Time Machine still shows the old Time Capsule name, with the new name underneath. When I try to back up using this disk, it shows the following error message:
"Time Machine could not complete the backup. The backup disk image "/Volumes/Old Time Capsule name/My laptop name.sparsebundle" could not be accessed (error -1)."
I don't know how to fix this. I have looked everywhere. I deleted the NetworkInterfaces.plist file in Library/Preferences/SystemConfiguration, and even made sure to do a secure empty trash. I even did a soft reset of the Time Capsule to the factory configuration, and renamed the Time Capsule all over again. I restarted the computer several times during this process, and yet no luck, it still shows the old Time Capsule name.
Does anybody know how to fix this? Thank you!

Ok, the MacBook is backing up now. Here is what I did:
After manually changing the name of the Time Capsule Disk as above, Time Machine was still not able to back up. I kept getting the error message
"Time Machine could not complete the backup. The backup disk image "/Volumes/Old Time Capsule name/My laptop name.sparsebundle" could not be accessed (error -1)."
The problem is that "My laptop name" Time Machine was using is wrong. I had changed the laptop name in Network Perferences>Sharing before, but it still kept looking for the wrong .sparsebundle file in the Time Capsule. I don't know why, and I even deleted the NetworkInterfaces.plist file again with no success.
I entered the Time Capsule from the Finder menu, found the .sparsebundle file with the wrong name, and manually deleted it. Finally the MacBook was able to backup. However, although the MacBook name is the same as it used to be before, and even though there was already an old .sparsebundle file with the correct name, Time Machine created a new .sparesebundle with the same name, and began an entirely new backup. I am just letting it do this backup, and then I will manually delete the old backup, so it doesn't take space on the Time Capsule. I don't need the past backups (and hope I won't swallow my words), and I am tired of dealing with this, so this will be it.

Help with Time Capsule with a new modem

Hi,
I did a search and couldn't find what I'm looking for. What is the easiest way to setup my Time capsule with a new modem? I will be using wifi with the time capsule. I just got a new modem and the time capsule keeps flashing a amber light. It was working off wifi before I got the new modem.
Thanks, Jerry

There is only one right value for wireless now. Which I did list in the instructions.
WPA2-PSK (AES) for the arris.
WPA2-Personal for the TC.
Did you reboot everything when you disconnected the ethernet.. so the computer and TC can reallocate the IP addresses. This is important.
Reboot everything when you rearrange networks.. always do it.. even I am forced to do it.
Reboot in this order.. from off.. everything off.
Modem.. wait 2min
TC.. wait 2min
Computer.. this will now pick up a new IP from the whichever wireless is stronger.. should not make any difference if it is the TC or the Arris.
Now see if the TC is available in airport utility.
If it fails .. reconnect it by ethernet to the computer.
Give it a different wireless name .. ie the Arris and the TC will have different names.
And you are using "create a wireless network" in the TC.. no other option will work.
Update the TC so the setup is saved.
Unplug the TC from the computer and plug it into the Arris..
Now reboot everything.. sorry.. but it is the easiest way to clear up old settings and get everything going again.
Now in the computer you will need to open the airport and find the TC wireless.. and then you connect to it.
Once you connect direct to the TC you should have no trouble.
You can setup and fix any issues.. there are always a few silly things.. password default or wan setup .. choose ignore or change settings.

Best configuration to extend wifi with Time Capsule & Airport Express

In my house I have a Fritzbox wifi router on the ground floor as my primary internet access. I have an ethernet cable going to the 3rd floor study where the Fritzbox signal is relatively weak. I purchased a Time Capsule as a backup device, but also wanted to extend the Fritzbox wifi network by plugging the ethernet cable in to the TC. I was not successful in extending the network, so I had to create a new network. When moving from downstairs to upstairs, my iphone keeps the connection to the (now weak) wifi network and I have to manually change to the (stronger) TC wifi network.
Additionally, I used to be able to successfully extend the downstairs wifi using my Airport Express (and also managed to have my speakers plugged into this for wireless usage), but do not want to additionally complicate my set-up.
So, what is the best way to connect the following equipment, ideally with the same network name, to ensure I always use the strongrst signal automatically:
Third floor:          iMac,    Macbook,   Time Capsule, Airport Express
          Ethernet cable from ground floor to 3rd floor
Ground floor:     Fritzbox wifi connected to internet

You must configure the Bridge Mode setting as the very last step before you Update the settings, otherwise the setting will change automatically.
In other words, you can change the setting to Bridge Mode, but if you make any other changes before you click Update, the Bridge Mode setting will not take effect.
Or, if you see any error messages about DHCP conflicts or Double NAT....the AirPort is not in Bridge Mode...even though you might think it is. Check the settings again.
will I still be able to set up an additional 5GHz network in parallel?
Yes

Just installed a new time capsule and i want to use my airport express to extend my wireless range....time capsule working with existing devices at this time...but i am not able to get airport utility to recognize the airport express.....????

just installed a new time capsule and i want to use my airport express to extend my wireless range....time capsule working with existing devices at this time...but i am not able to get airport utility to recognize the airport express.....????

Temporarily connecting your AirPort Express to one of the Time Capsule's Etherent LAN <-> ports...as LaPastenagure suggests....is always a good way to setup and configure other network devices.
If you want to configure the Express using wireless, remember that the Express broadcasts a default wireless signal with a name like Apple Network xxxxxx. You must log on to this network first....no password is required....then open AirPort Utility to "see" the AirPort Express.

Do you have to disable your Wifi on your existing Reuter if using time capsule to Create a new network

Does one need to disable the wifi on ones reuter if using a time capsule to create a new network what happens if you don't and what are the benefits of doing so

No but you may experience a bag of hurt from cross channel interference. You may have to reset the Subset Mask of one of the routers along with separating the broadcast channels.
Further if you then have one device a PC perhaps on one network and your Mac on another you may not be able to share files/ITunes etc.... with any ease.
So switching off the Wifi on the router/modem and hanging an Ethernet cable to the Time Capsule and setting that up as your WiFi router distributing the IP addresses over DHCP really is the least problematical approach.
IF you have cable Internet with a decoder with Ethernet output ditch your old router completely !

Time capsule setup with Bell modem

I'm having a lot of problems trying to set up my new Time Capsule 3TB. I have a Bell modem. When setting up, device asking for PPPoE settings of service provider. I am entering username and password provided with Bell modem, but keep experiencing errors. I have tried rebooting Bell modem and have reset my Time Capsule at least 3 times without success. Note that I have the Time Capsule hooked up to Bell modem directly using a high speed telephone cable. What am I doing wrong??

Did you follow what I said.. use ethernet only in full isolation?
Does the ethernet port get the correct IP from the TC? ie 10.0.1.2
If not the TC could actually be faulty.
If you do get the correct IP and it is just a setup issue.. make sure you have ipv6 set to local-link for the ethernet connection.. this is essential to get it to work.
Once you do that.. it should then show as icon in the airport utility and you can do the rest of the setup.
Other than that I will check if Bob can help you.
He will get you to try and do the setup via wireless I think.. the new version products seem to setup better via wireless.
Also if you have an iOS product with the latest airport utility .. that seems to often work better to get over the line than the Mac utility.
If you have only had it a week or so you can return it no questions asked.
You should also still have support from Apple by phone to do the setup.. although lately they have been telling people the TC or AE should not be bridged.. so they will try and get you to bridge the modem which I don't think you can.

Can't copy with LaCie Network Attached Storage and Time Capsule/Airport

Hi,
I bought a Time Capsule to replace my recently faulty modem/router Linksys AG241 and in preparation of buying my first mac in the next few months.
Right now the network is as follows:
— 1 Linksys AM200 modem connected to the TC by ethernet and set to bridge mode
— 2 windowsXP pcs attached by ethernet to the Time Capsule
— 1 NAS (LaCie 2Big Network) attached by ethernet to the Time Capsule
Despite some initial problems configuring the modem in bridge mode, the present problem is the following:
Everytime I try to copy a file (it can be either an 4MB file or an 800MB one) I get this error window:
— Cannot copy "Filename": the specified network name is no longer available
Even when copying a file from one Share of the disk to another! However, have no trouble copying 1KB file, for example.
I've been searching throughout the internet for some days now but couldn't find any answer.
This LaCie NAS External Disk is ethernet-only and can only be connected to a switch or a router. It worked before with my older modem/router. I changed the ethernet cable by another one and I get the same result.
The Time Capsule is cofigured to distribute IPs through DHCP. Right now, I even have enabled the DHCP reservations to assign a static IP to the NAS, and to the Pcs. STill the same result.
This happens on both pcs. Still haven't tried with a wireless device yet (I don't have one).
Can anyone help me solve this?

Ok. I've ran a test on a friend's network in order to clarify if the LaCie NAS was the hardware causing this issue.
Well, it isn't. The NAS worked fine on this other network setting - which uses a different router, modem and 2 different computers.
The test ocurred in Wireless G, though, not by Ethernet connection with the computers.
*So I guess the problem must be on my Time Capsule or Modem?*
*Possibly a configuration issue.*
Does anyone has/had some problem connecting Ethernet External Disks on a Time Capsule/Airport that can share some Solution ?
Please, Help!?

How do I make airport time capsule work with Linksys cisco router?

Hi all.
I bought an airport time capsule 3T and want to connect it to the internet, using a macbook with OS X 10.9.2. Currently I am using a Linksys Cisco router model WAG54G2.
I followed the steps of the setup airport guide: Connected the WAN port of the airport with an ethernet port on the router, plugged in the power cable, filled in the internet username and password. In Airport Utility I can see the airport and the internet icon, both with green dots most of the time. But it seems to disconnect every minute or so, green dots turning orange and the status light on the airport flashing orange. The internet light on the linksys also goes on and off. When the internet is on, it is quite slow.
Advice is welcome!
Kees

No guarantees here. AirPort Utility 6.3.1 is a big drop down from the 5.x versions in Leopard and Snow Leopard.
Hold in the reset button on the back of the Time Capsule for 9-10 seconds and release
Allow a full minute for the TC to restart to a slow, blinking amber light
Click the AirPort icon at the top of the screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click on Time Capsule.
The example below shows an AirPort Express. You will see Time Capsule.
As soon as you click on the Time Capsule, AirPort Setup will open up automatically and take a minute to analyze the network....and probably suggest that the Time Capule will be configured to "extend"....which is wrong.
Click the Other Options button at the lower left
Click Add to an existing network
Next to Connect To.....select the wireless network name from the drop down list....if it appears. Otherwise type in the exact name of the wireless network.
Click Next
Confirm any settings again and wait to see if AirPort Utility 6.3.1 will allow the Time Capsule to join the wireless network.
You have about a 1 in 5 chance that this will occur.
Post back on your results.

Regarding the product time capsule...is the modem the same as airport extreme and is the disk drive always running? I'm worried about it lasting for at least five years.

Regarding the product Time Capsule... is the modem the same as the Airport extreme and is the disk drive always running??? I'm worried about it lasting at least five years.

John,
I'd pay good money to bet it wouldn't last 5 years... I don't rate the in built power supply and as for "server grade hard disk" - Hmmmm..... The failure rate of all HD's on the market after 3 year is 60%.
Regards,
Shawn

I like the idea of auto back-up for my new iMac, Ipad and PC Netbook, particularly if I can access all files and data stored on any device. But I have a Conceptronic router. Will Time Capsule work with this and how?

I like the idea of auto back-up for my new iMac, Ipad and PC Netbook, particularly if I can access all files and data stored on any device. But I have a Conceptronic router.
1. Will Time Capsule work with this and how?
2. Can my printer USB be plugged in and then shared between the devices?
3. Can I create a network and how?
4. What happend when a visitor logs onto my existing wireless router?
I'm new to Macs (well a returning user having started with Mac Plus!!) and not very technical. Any help / advice will be much appreciated.
Ray

The key to what you seem to want to do is to be able to get Apple's Time Capsule router to "join" the network that your Conceptronic router. I believe that works with some third-party routers, but I've never seen a list of those that work in such a configuration and I have no experience with Conceptronic equipment.
You might be better off with a Network-Attached Storage (NAS) device instead of a Time Capsule.

Configuring the time capsule airport wlan function as "connect to wlan", the time caspule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport Express it worked!

Configuring the time capsule airport wlan function as "connect to wlan", the time capsule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport express it worked, the single Ethernet port got the IP Parameters passed through!
My setup is a Vodafon Esaybox connected to ISP. Time Capsule is not able to extend the wlan of the easybox, neither airport express can do.
Only the option "connect to wlan" is succesful.
With airport express I was able to connect my Sony Bravia TV to the lan via ethernet to stream pictures, the TV set got an IP adress from the easybox.
With the time capsule the easybox dosn't find devices connected to the ethernet ports to submit IP adresses. The TV set get another IP adress (169.xxx.x.x.) in subnet mask 255.255.0.0 and I don not now where from.
My notebook is a MacBook pro.
Any idea????
Thank a lot in advance!
Kind regards
Ingo

Neverthe less, could there be the chance, that this feature could be implemnented with an firmware update?
That would appear to be a question for Apple to answer. You can make suggestions to Apple here:
Apple - AirPort Extreme - Feedback
If the AirPort Extreme and Time Capsule are configured to "extend a wireless network" they will provide additional wireless coverage....and...the Ethernet ports are enabled in this type of setup.
The "catch" here is that you must have an Apple router providing the network to be extended.

Do i need to set up the time capsule airport before i start backing up using time machine with my time capsule?

Do i need to set up the time capsule airport before i start backing up using time machine with my time capsule?

Some setup is generally required.. because the TC is a network device.. not a plug in via usb.. therefore it has to exist somewhere in your network.

Hi I've recenty purchased a new imac time capsule airport express. I've set up a new network, rather than extended the current one. How do I change my new network to an extended one or create an extended network?

Hi I've recenty purchased a new imac + time capsule + airport express.
I've set up a new network, rather than extended the current one. How do I change my new network to an extended one or create an extended network?
Michael

detailed in terms of what focus?
here is a video guide about using the airport utility
http://www.youtube.com/watch?v=65Jv6m43eIE

Guest network feature of Time Capsule/Airport Extreme in conflict with DNS on OS X Server?

Hi, I want use the guest network feature of Time Capsule/Airport Extreme which requires an external DNS server but my OS X Server is the dns server...Can I configure server and airport with an external dns without messing up my OS server?
Thx Ron

If you want to use the guest network while also using your server for DNS - you will need to do the following: It's a bit painful - but it works.
On your Airport Device (Airport Extreme or Time Capsule) - in the Internet tab you will need to do one of the following:
1) Leave the DNS Servers Blank - which they will default to the DNS servers provided by your ISP.
2) Actually enter your ISP's DNS servers.
3) Enter Open DNS servers (I use 208.67.222.222 / 208.67.220.220).
The DNS servers specified in the airport device must be internet routable addresses (if you are going to use the guest network functionality) - and cannot refer to private ip address (e.g. 10.x.x.x, 192.168.x.x, etc).
Here is the painful part...on all of the devices (Macs, PCs, phones, ipads - that will be used on your "private" network 10.0.1.x - you will need to provide static DNS setting (but still allow DHCP to assign the devices IP address). You will specify 10.0.1.13 as primary DNS and 208.267.222.222 (or your ISP's primary DNS IP).
One you do this - your devices that you permanently use on your local network - will still use your server for DNS - and the external DNS - should your DNS server happen to be down.
Anyone visiting your house - will connect to your guest network - and automatically be DHCP assigned a guest IP address - and the external DNS servers that you specified in the Airport Extreme device.
This has been working great for me. I suspect that the guest network functionality is flawed in the Airport Extreme/Express and Time Capsule. Since I do not have another router that provides a guest network - I cannot say whether this issues is limited to the Airport devices - or whether this workaround would need to be done - regardless of which brand of router is providing the guest network.
In a nutshell - your household permanent devices will have to specify static DNS servers - but your guests will connect seamlessly without having to change and risk messing up any of their device settings.
If this solution works for you - Please be sure to click either "This solved my problem" or "This helped me".

Time Capsule & Airport with a new modem WiFi

Similar Messages

Maybe you are looking for