Time Capsule and IPv6.

Hi Guys,
Has anyone succeeded in configuring their TC to support IPv6 natively? So no tunnelling, but native v6 from your provider. I've been trying just about anything but can't get it to work.
Any ideas? To be sure I use a Draytek Vigor 120 modem with IPv6 firmware and the TC is configured to route PPPoE from the Draytek.

It's a chicken-and-egg thing. Sites won't go IPv6 until ISPs provide the right infrastructure, and ISPs won't provide the right infrastructure until forced to because some sites are IPv6 only.
I think you'll see a lot more action on this in the next two years now that the main pool of IPv4 address is exhausted.
Truly, today, though, essentially nothing on the net publicly is IPv6. I actually hooked up with Hurricane Electric's free tunnel and had IPv6 working at my house for a short time (yes, through my Time Capsule -- worked fine), and I had lots of trouble finding anything to surf. Yes, Google and a few other sites have IPv6 sites, but they really are essentially no different than IPv4, or else they are specific sites just meant to test IPv6 (no real content). So, at least as of today, you're not missing anything.
Very few US ISPs have IPv6. Most are just in the beginning of tests with a few select customers. This is going to change over the next few years.
It isn't as simple as just flipping a switch, because as I mentioned, every computer becomes a fully addressable node on IPv6, and DHCP goes away, to be replaced mostly with a protocol where your ISP gives you a prefix, and your equipment appends a long suffix. Those two together uniquely identify your computer and can be found from ANYWHERE on internet. That means the routing protocols have to track a phenomenally larger number of routes than they did before, or (in practice) they have to hand off the job to routers down the line. The whole addressing scheme works differently and it will take some time for the ISP equipment to be fully compliant.

Similar Messages

U-verse, Time Capsule and IPv6

Can anyone recommend the best settings related to IPv6 when using ATT U-verse and Time Capsule? Time Capsule is set-up in Bridge Mode and IPv6 enabled on U-Verse Modem/Router.
Should IPv6 be set to Automatic or Link-Local on Time Capsule or should I disable IPv6 all together?

Because the other settings either do not work, or do not work reliably.....but Apple is "working on it".

Time Capsule and IPv6 in Bridge Mode

When the Time Capsule is placed into Bridge Mode (i.e. operating as a layer 2 device) the device will NOT participate in IPv6 Stateless Autoconfiguration and hence will not use IPv6. This limits my ability to perform incremental backups to my home IPv6 network when my Macbook Pro resides on my "away" IPv6 networks. I've checked the settings endlessly but can't seem to find any "enable IPv6 Stateless Autoconfiguration in bridge mode" button. Am I missing something or is IPv6 used only when the device is operating as a Layer 3 device when a non RFC1918 address is in use on the WAN port?

Because the other settings either do not work, or do not work reliably.....but Apple is "working on it".

How will the Time Capsule support IPv6 and coop with the new emerging security threats that will emerge due to the new technical possibilities that IPv6 provide?

How will the Time Capsule support IPv6 and coop with the new emerging security threats that will emerge due to the new technical possibilities that IPv6 provide?

Cross your fingers and hope.
Obviously if there is any big or known threat Apple will send out a firmware fix.
But the TC is designed to be end user simple device. It has no firewall that is visible at any rate. I don't know that it truly doesn't have a firewall but it is not part of the end user controls.
IMO if you have major security concerns that go beyond end device firewall, which is where Apple do put most of the security, since firewall in the router is plainly not a stop to anybody deliberately downloading an infected file or website, and most end users.. do not want a firewall that prevents them using the web like a business does, where only certain ports are allowed. Everything else tough luck.. you are not allowed to use it. Then TC is unsuitable for you anyway.. buy a proper firewall appliance.

XBOX ONE. I have the xbox one and the airport time capsule and cant connect to most xbox live games and zero parties. I have 0 experience in all this but somehow was able to change NAT to open but still wont connect. HELLLPPPP

Okay folks, I need your help out there.
So the nerdy side of me went and picked up the XBOX ONE on release day. Its awesome by the way, BUT..... I cant seem to connect to most xbox live games and absolutely ZERO parties. At first I just thought it was something to do with the xbox itself and would eventually fix itself, but i was wrong. After looking into it on microsoft, i found out that it had to do with my NAT settings on the airport itself. I guess apple and xbox are not compatiable for xbox live and it makes it difficult to have an open NAT setting and is a huge PAIN.
I was able to pinpoint one that the airport time capsule was blocking the IPV6 something or another. Anyways, I unblocked that, and reset the modem and time capsule and jumped on the xbox and now have open NAT settings but still cant connect to multi-player.
Upon further searching, i was told to uncheck the UPNP on my time capsule as well, but have no idea how to find that.
I know it seems confusing, but thats the best i can describe it.
tthanks all

Be a long long time before I see an Xbox One.. but whoever told you to uncheck the upnp in the TC.. tell them their dreamin' .. upnp is not support by Apple in any computer or router, never has been.. Apple deliberately wrote their own version called NAT-PMP to do the same thing.. dynamically open ports at the request of an application or client computer.
So there is nothing like that to uncheck.. and as a matter of interest.. there no box to check or uncheck for NAT-PMP either.. since apple do not believe in end user adjustment of settings.. they simply do not exist.
You will have to manually forward all ports required by the Xbox via the TC. For multi-player games you probably need to open more ports than the standard to allow just xbox live. You will need to check the ports required and open them.
OR
Buy a standard vista UPNP compatible router.. and use that.. and simply put the TC in bridge in the network.
I have not seen posts yet about xbox one.. but there are plenty about xbox and ps3 and the fact that Apple really doesn't give a hoot about games consoles.
This is a good basic post for older xbox.
https://discussions.apple.com/thread/5385065?tstart=0

Time Capsule and External HD as Network Attached Storage

I was wondering if I can
a. Attached and external hard drive to my Time Capsule and access is wirelessly?
b. Back up to that external hard drive using Time Machine?
c. Access that external hard drive and Time Capsule from a remote place off site?
Thanks

a. Yes
b. I think so. But why not just use the TCs hard disk for TM backups?
c. Apparently so based on these instructions I have found: (Haven't tried it myself)
In the Finder preferences check the box "show server" to mount to desktop.
Under Airport Utility:
Disks - check over wan and check file sharing and write down the ip address
Under the Finder, use the GO function to find your server ie the hard drive on the TC. In the window provided type afp://ip address then password if applicable. The hard drive should mount and be shown on the desktop.

Can I use the new Time Capsule to backup my mid 2010 Macbook Pro? Also can I want to free up my hard disk, can I save my photos and files on the time capsule and later access through wifi?

Can I use the new Time Capsule to backup my mid 2010 Macbook Pro? Also can I want to free up my hard disk, can I save my photos and files on the time capsule and later access through wifi?

Can I use the new Time Capsule to backup my mid 2010 Macbook Pro?
Yes, if you are asking about using Time Machine to backup the Mac.
Also can I want to free up my hard disk, can I save my photos and files on the time capsule and later access through wifi?
You are not thinking of deleting the photos and files on your Mac, are you? If you do this, you will have no backups for those files.
Another concern is that Time Machine backs up the changes on your Mac. At some point, Time Machine will automatically delete the photos and files from the Time Capsule.....you just don't know when this might occur.
In other words, only delete files from your Mac that you can afford to lose.

I recently bought a new iMac as well as a wireless time capsule and have it connected how can I use this external drive as the location to store all my files for iTunes, or is this even possible?

New iMac user here, I recently bought a new iMac and Time capsule and have the whole network up and running now. I have connected another external HD to the time capsule as well and have a total of 3 TB of storage connected wireless to my new iMac. My question is can I use this location as the default location for iTunes? I doubt I am gonna run out of room considering the iMac has 1 TB of storage already, but I'd prefer to keep my movies and music off the Mac to keep it running smoothly. If this is possibly, I'd like to do this with iPhoto as well.

I would advise against placing your iTunes library on a Time Capsule.
The Time Capsule is designed as a backup device and not for wireless streaming of video.
Before you do anything more, can I suggest you put into place a reliable, redundant backup strategy.
Unless you are prepared to risk loss of your iTunes library due to a hard drive failure, I would not put iTunes on the Time Capsule.
Leave your iTunes library on your iMac until such time as your internal drive is full. Backup to Time Capsule using Time Machine and create a clone of your internal iMac HD to your external drive.
That's my 2 cents worth. Others may have a different opinion.

Time Capsule and time machine with third party router

Hi,
This is the first time I use this site.
I have over three years old Mackbook.
APP has expired.
Now I want to know how to set up time capsule in a new environment.
I moved from Australian and Singapore.
I was using Time Capsule and Airport Extreme in Australia.
I have moved to Singapore.
I am using router provided by Singtell(Singapore Telecommunication). I do not have an Airport Extreme anymore. My housemate and I are using wireless internet-sharing. Needless to say that internet provider is SingTell.
Now I would like to know how to use time capsule and time machine with the network created with a router provided by SingTell.
What I did so far is;
Connected the time capsule to the power point.
Orange lamp lit and flashed for a few second and stop. Orange lamp stayed on.
Apple Utility does not recognise Time Capsule.
I prefer to use it wirelessly.
There are only two USB cable ports installed.
One is used to synchronize iPhone.
Other is used for a printer.
but if it is not possible, wired would be OK.
MacBook 13 inch 2.0 GH Late 2006
I hope that someone able to give me an answer for this.
Cheers,
morepubholidays

In this case the apple support people reveal a truly poor understanding.
You must bridge something.. you either bridge the TC.. which 90% of people do.. or you bridge the dsl router.. which some people do manage to do.. You will have to look that up for your modem and check with verizon if they support pppoe authentication.
IMHO just bridge the TC as you were told not to do.. as they are simply wrong about that.
If you already tried this and it didn't work.. try again.. it is the correct approach.
You have no choice. But this time let me suggest you do it using the 5.6 airport utility.. as the apple toyland v6 airport utility is likely half your trouble.
So here is how to get the utility into your computer.
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. it is very simple.. drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. drill down.. applications utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall 6.1 so don't try.. and you cannot or should not run them both at the same time.. so just ignore the toyland version.. the plastic hammer.. and start using 5.6.. a real tool.
For screen shots see this post.
https://discussions.apple.com/thread/4668746?tstart=0
Then open the manual setup on the 5.6 utility.. go to internet tab. Connection sharing.. off bridged mode.
Select this and update..
Then all your IP addresses will be wrong.. I suspect this is where things are going wrong.. and messing you up.
Once the TC is bridged.. turn off everything and restart.. in correct order.. modem.. TC.. client computers etc. 2min gap between each.

New to time capsule and need help with installing it?

I just bought a new 3tb time capsule and also new to apple routers I want to use this as my new wireless router how do I go about switching this out with my router now. Im using a linskys router now nothing special I think its only a 300Mbps the only problem is that we just had our new house complete and prewired with ethernet connection in every room and a security system that runs off of the router how do I go about switching that set up to the new time capsule? I know if I had to have the company come out to do it they charge a hefty fee which I know its that hard to do the only thing that's stopping me is that set up to the security system I don't want to screw that up???

Three different aspects
1. Set the form up to submit the data (XML or FDF), not the full PDF. You can import the data to the PDF on your end.
2. You can turn on Extended Reader Rights, but then limit the use/users to 500 by the EULA. The applicability of this option depends on your intended application. In a small office, it would be fine. For general web use you would likely exceed the limit and be in violation of the EULA.
3. There may be an e-mail problem, one reason that e-mail is not recommended for form submission (even if the manual discusses it). Again, in a controlled environment like an office it will probably work fine, but in a web setup it is best to use a web script. There are 2 problems with e-mail that both depend on the client system (YOU have no control, but will be blamed in any case). First, the client machine has to be set up as an active MAPI client. Many folks do not have this on. Second, some e-mail clients treat PDFs like text and the result is a corrupt e-mail submission, even if it makes to you.
If you have the possibility of web submission, do it. I suggest only having the form data submitted and not the form.

2TB Time Capsule and Time Machine on Snow Leopard 10.6.1 slooooooow

I have a 2TB Time Capsule on a 100Mps LAN that is shared by my Mac Pro and an iMac G5. No USB devices are connected to the Time Capsule. The Time Capsule and both computers are connected to the LAN through a LinkSys 8-port Cable/Router/DHCP.
While in Time Machine (about 30 backup folders) looking for a file to restore, it takes 2-5 minutes for Time Machine to change between backups. The time line on the right responds extremely slowly.
Whether or not the iMac is backing up has no effect.
Is this normal?
Thank you,
Don

See: http://www.codedifferent.com/2009/09/02/howto-reactivate-your-kyocera-printer-un der-mac-os-x-snow-leopard/
We have a KM-2550 and this solved it. HTH.

I recently purchased a time capsule and thought I would put my itunes on it as an external drive as my mac book air only has 120gb. However I can not be connected to the internet and the TC at the same time in order to download the files to the TC. Help?

I recently purchased a Time Capsule and put my iTunes library on there so that I wasn't using up my hard drive space. Only 120gb on my mac book air. However when I download songs from iTunes I can not be connected wirelessly to the internet at the same time. Can I hard wire my TC in to my mac so that I can treat the TC as just an external hard drive? Thanks

Initially, you asked if you can hardwire your MBA to the TC. The answer is yes, by using the optional USB Ethernet adapter that Apple provides. However, in order for your MBA to access the TC's internal or USB-attached HDD, it would need to establish a network connection to it. This would be true of any NAS device on an Ethernet network. Therein, lies the problem. Your MBA cannot connect to two networks simultaneously.
One option then, would be to have two separate iTunes Media folders; one on the MBA & the other on the TC. This way, you can download the music to your MBA when connected to the Internet at the AirPort lounge, and then use iTunes Consolidate Library feature to transfer the audio files to the TC's iTunes Media Folder location. A great program to help maintain multiple iTunes Librarys and/or Media Folders, that you may want to consider, is PowerTunes.

Setting up Air play with new time capsule and newer airport express?

I just recently purchased a new time capsule, and I'd like to use my current generation airport express to stream music from my apple devices. I just was wondering what I had to do in airport utility to set this up? I was also wondering how to transition the network over from the old express to the new time capsule as far software settings go. I really appreciate the help and assistance. Thanks folks. I'm really looking forward to setting up the network for our new iMac.

Your setup is very easy..
This is how I would do it.
Remove the express from the network.. ie just unplug it but do not change anything in it. Keep the configuration as is until the TC is working.
Power off the cable modem.. this is requirement.. at least 20min is usually needed, dependining on your ISP.
Go into the airport utility and setup the TC as router for your network .. it is a simple setup.. but I would do as stated.. all short names, no spaces pure alphanumeric rather than accept Apple's names. That is for TC and wireless.
After 20min power up the cable modem. Once it is running and you have internet access. you can proceed to setup the express to do the airplay. If the internet still doesn't work, power off the cable modem overnight..
Do not lose that express setup so if you absolutely have to, you can at any time substitute it back and have internet again.
So everything is working properly TC in place as full router.. now hard reset the express.. and simply use the airport utility to put it in extend wireless .. or plug in by ethernet if you are going to hard wire it.
The extend wireless setup is all done straight from the existing setup.
Now you can plug your express audio port into your speaker.. and setup the airplay via the itunes.
I will get Bob to give you his way of doing it.. There is no one RIGHT way .. but he can give you more info if you want a particular method.

Trying to restore after getting a new hard drive. I can see the backup on the Time Capsule and on the correct date but it is Greyed out. That is it wont let me open it and restore the machine. Have tried also Migration Assistant, no luck.

Trying to restore after getting a new hard drive. I can see the backup on the Time Capsule and on the correct date but it is Greyed out. That is it wont let me open it and restore the machine. Have tried also Migration Assistant, no luck.

https://discussions.apple.com/thread/5210788?tstart=0
At startup hold down the Command+Option/Alt+r keys until you see a globe on the screen. Then use disk utility to partition and format the drive HSF+ and then select Reinstall Mac OS X. whatever version of OS X that originally came on your system will be installed and then you can upgrade back to Mavericks.

I have question about hooking up an external hdd to a time capsule and still have my printer hooked up as well. Anyone got any tips for me, how to do it and what brand of harddrive that will work best for me 1 or 2 TB

i have question about hooking up an external hdd to a time capsule and still have my printer hooked up as well. Anyone got any tips for me, how to do it and what brand of harddrive that will work best for me 1 or 2 TB

You just need a powered hub.. if you already use one then fine.
Plug in just about any external hard disk will work fine. Format has to be readable by the TC.. ie fat32.. or much better HFS+.. plug it into a Mac to prepare the drive.
Pick whatever size suits.. nowadays 2TB are most economical.
WD, Seagate have goobled up all the minor players.. so pick one.
Whatever suits your budget and asthetics.
NOTE.. The USB on the TC is fine for printers.. IMHO it is the wrong way to go with USB disks.. use the internal disk of the TC.. USB is less than half the native speed plugged into a Mac.. TC to USB is slow.. far slower than internal drive.. or using external drive as external.

Time Capsule and IPv6.

Similar Messages

Maybe you are looking for