Time Capsule and Netgear Setup

Hi,
This is probably discussed a thousand times but i need some help with my brand new timecapsule. I spent a couple of hours trying to set up the timecapsule to wirelessly join my existing network and after doing it the Airport Utility failed to find it.
My set up is as follows:
1) I have a macbook pro and a powerbook
2) my wife has a laptop pc
3) Netgear wireless router
I don't want the TC to be my primary router or for us to use to access the internet. Do i need to connect the TC to the netgear via cable? And i presume then the machines in the house will be able to see the TC?
Any help would be appreciated!

This is my current setup and so far it works well:
Netgear DG834GT wireless modem/router connected to my adsl line and set for DCHP and to manage all IP addresses. XP PC connected to the Netgear with ethernet from a LAN port. Another ethernet cable from the Netgear to the WAN port on the TC. My firt connection to the TC for my MBP was via ethernet cable for the initial TM backup, this takes a long time, I suggest you leave it running overnight.
After the first back up disconnect the ethernet between TC and MBP and using airport utility (make sure you have the latest version loaded first)set up the wireless network and TC to operate in bridge mode(I am using "n" at 2.4Ghz now, I set it up at 5 Ghz initially but had intermittent connections - has now been connected for 4 days without any problem so far).
I have left the wireless enabled on the netgear so that I can connect other laptops running XP and "g" wireless though have not tested this yet but the MBP does see this network.
This setup allows ethernet and wireless "g" to run from the netgear and "n" enabled wireless to run from the TC to my MBP. This means the MBP always connects at "n" speeds no matter what is connected to the Netgear.
I have Bonjour running on the PC and my USB printer connected to the USB port on the TC. With sharing enabled I can write between the PC, MBP and TC, am also able to connect both to the printer.
The only things I haven't tested yet are "g" enabled laptops to the Netgear and a USB external drive on the TC. Will probably try this over the weekend.
To get all this to work I just followed the Apple guides, everything worked out well except for the initial internet connection with Airport set to 5Ghz.
As far as heat is concerned the TC does run very hot during the inital back up after that it is not much hotter than the Netgear or the MBP when they are running programs.
Hope this helps you guys and persevere with the setup, it's great when it all comes togeather.

Similar Messages

Time Capsule and Netgear Powerline

I have a 2TB Time capsule and need to extend my network (wired) through HomePlugs. I have had the Netgear Powerline recommended but have noted in the blurb that they are 'not Mac compatible'.
Will they work with my TC and is it simply just a case of plugging them in and they work or is there anything else I need to do settings wise on the TC?
If these will not work can anyone recommend otheres that do and also walk me through the settings I will need to change 9in very simple steps as I am a bit thick ).
Thanks in advance for any help.

Everything works. Follow directions for extending your wireless network at:
http://support.apple.com/kb/HT4259
Notes:
I first connected the Time Capsule directly to the AirPort Exteme to avoid any powerline networking issues. This allowed both the time capsule and airport extreme to show up in the AirPort Utility program.
Ensure that in the AirPort Extreme's wireless settings, "Allow this network to be extended" is enabled/checked before you modify the Time Capsule's settings; the "allow... extended" checkbox might not be visible if you are not directly connected as a client to the AirPort Extreme (it is not visible after setup when you are a client of the time capsule extender).
The Time Capsule network setup is easiest if you follow the dialogs instead of doing it manually.
I now have cable modem->ABEX->Netgear HomePlug-> Netgear XAV1004 switch-> Time Capsule->extended wireless network->laptop. The powerline adapter signal is running from a new house addition built in 1999 through a sub-panel circuit breaker to a main circuit breaker out through 1940s-era wiring, and everything works perfectly, including Time Machine backups from machines on both sides of the powerline adapters.
@LaPastenague: I haven't detected any ports blocked by my Netgear powerline adapter, nor could I find any port blocking topics via an internet search. I have never installed any of the Netgear management software, so my powerline adapters are not running any encryption... maybe encryption comms cause the issue you raised? I really doubt the Netgear PowerLine adapters block any host-specific ports because the adapters are working at the physical and data-link layers which are below the port assignments in the transport layer of the OSI model.

Running a network with Time Capsule and Netgear router - is it possible?

We have an iMac and a Toshiba laptop. I was wondering if it was possible to have a wireless network with a Time Capsule and our Netgear DG834G router. We live in a solid brick house and the Netgear router is upstairs and we find we get very little, if any reception from downstairs. We have just purchased the Time Capsule and we were hoping to move the Netgear downstairs and have the Time Capsule upstairs to get reception all over the house. Is running a network like this possible, and if it is, how do we do it. Both the iMac and the laptop need to be able to connect. Thanks in advance.

g'day
you could try a pair of those http://www.amazon.co.uk/Devolo-MicroLink-dLAN-Highspeed-Starter/dp/B000A7IE7Y
see if this thread can help you in your planning http://discussions.apple.com/message.jspa?messageID=10430294#10430294

Wireless Access Points - Time Capsule and Netgear

Ok...Netgear support site was completely useless so I am hoping that someone over here can help me out. I think what I am trying to do is relatively simple but for 3 days now I have gotten no-joy.
Here is my current configuration: Westell DSL Modem (wireless disabled) --wired-- Netgear WNR834B (SSID 1, operating b/g mode) --wired-- Time Capsule (SSID 2, operating n mode, connection sharing Off Bridge mode). All other devices are hanging off wirelessly to one of the two routers.
What I am trying to do is add a wireless Access Point (Netgear WN802T) to the picture. I need better coverage on the other side of the house and don't want to run wires. The WNR834B is WDS compatible but I can't figure out how to put it into repeater mode or bridge mode. So I thought my next best bet (before going out and buying even more hardware) would be to try and extend the TIme Capsule network. I have been unsuccessful so far (SSIDs are the same, channels are the same, WEP set because I read somewhere that WPA was not supported in repeater/bridge mode). Is it even possible to use a Netgear Access Point with the Time Capsule (I would think it would work, but I just can't get it to).
I can get the WN802T to be seen in my network, but I can not get it to carry the internet connection.
Any advice or steps would be GREATLY appreciated.
Thanks in advance for any/all help

friars, welcome to the discussions!
Sorry, but the possibility of extending the wireless network created by the Time Capsule with a device from another manufacturer is almost zero. Based on information from other top users, the only Netgear model that is shown as WDS compatible with an Apple base station is a model WGR614 v6.
Take a look at an Apple AirPort Express to "extend" the network created by the Time Capsule. While the Express will also do WDS, the bandwidth on your network will be cut by 50% with the addition of just one WDS device. The "extend" feature on the Express does not impose this type of penalty and it is fully WPA/WPA2 capable as well, much more secure than WEP.
For about the same money as an Express, you might also consider ethernet power line adapters. Almost as good as having a direct ethernet connection. Available from Netgear, Linksys, and others.

I have working Netgear network. Want to add new Time Capsule and run 2nd network for new apple TV and Imac, and keep the netgear network for my PC and Canon printer.

I have working Netgear N600 dual band router network. The existing network has an XP netbook PC, canon printer, 2 Iphones, Epson Air printer, an Ipad, 3 roku boxes, backup drive. Just bought a new Apple TV box, and time capsule 2T. I have an IMac on order but don't have it here yet.
My goal is to add new Time Capsule and create 2nd "apple" network for new apple TV, Iphones, Ipad, Epson Air printer and new Imac, and keep the netgear network for my PC, Roku TV boxes, and Canon printer and backup drive.
The Netgear router, the time capsule and new IMac will be on the same desktop, I dont need to backup my netbook PC to time capsule.
Where do I start?
Which device connects to my modem first, the TC2 or the Netgear?
Is it best wait for the Imac before starting or can the TC2 be set up from my Ipad or PC?
Thanks.

It is pretty simple..
Setup the TC in bridge and plug it into the Netgear.. I would leave the netgear as the main router for now, although in the future you can swap things around. The netgear firmware may have issues with bonjour and airplay/airprint?? Does your ipad print ok now?
You can setup the TC using Mac, PC (at least up to win7) or iOS.. they all have airport utility available.
Bridge mode is set differently depending on the version of the utility. This is v5 and how the windows one will look (at least similar to).
v6 will be as
With the TC in bridge you will still create a wireless network.. and give it a different name from the netgear.. then all the apple devices can connect to it. Use ethernet rather than wireless if the imac is on the desktop with it. Much faster and better for using Time Machine backups.
If you run into any issues.. just post the particular issue. It will take a bit of getting used to, but isn't hard.

HT4145 I want to add airport express. I now have time capsule and I am confuse. Do I setup the express and then time capsule to the express?

I want to add airport express. I now have time capsule and I am confuse. Do I setup the express and then time capsule to the express?

Setup the Express to wirelessly extend the Time Capsule, or vice versa depending on which one is already set up. Or you could use bridge mode which involves using an Ethernet cable or Powerline plugs.

SOLVED: Dropped connections with Time Capsule and cable modem/router

I've been dealing with random dropped connections for quite a while and I thought that it would be useful to share what I've found.
I was having a very puzzling problem where my internet connection would drop randomly on wireless devices. On my laptop, webpages would suddenly become unresponsive for a minute or two, Mail would have connection problems and complain, etc...but incredibly randomly and definitely not repeatable or in any pattern that I noticed.
I also have 2 Nest thermostats in the house which connect via wi-fi. I noticed that they would randomly show Offline very often when viewed from a webpage or iPhone app, but the Nest front panels showed that they were connected with a strong signal.
As I said, the dropped connections were very sporadic. Most of the time, everything worked, but every once in a while...bam.
I worked with the level 3 tech support guys at Nest for over a week to figure out what was going on. We went through settings on my router and Time Capsule and everything seemed proper and okay. I even replaced the Nests with new ones but still had the same problem. We were all completely stumped.
Yesterday, my laptop dropped it's connection at the same time my wife's laptop dropped hers. At this point, I wondered if something was wrong with the Time Capsule or maybe my internet provider.
I called AppleCare to see if they could help with debugging the problem. They passed me up to a senior wi-fi tech and he asked me many questions about the configuration of my network. My home network looked like this yesterday (see crappy diagram below)
                                                     Motorola Cable modem/router
                                                                             |
                                                       Netgear multiport switch
                                                      |          |         |         |          |
                                                     hardwired Macs,            TimeCapsule (bridge mode)
                                                     laser printers,                   |   |   |   |   |
                                                      Apple TVs                       laptops, Nest, iphones
This configuration seemed correct to me. The Time Capsule in bridge mode would mean that the cable modem/router would be handling DHCP so all the devices would be on the same network and I could print from a laptop to one of my printers and the laptops could connect to the hardwired Macs, etc..
The AppleCare technician said he thought that bridge mode was the problem. He mentioned that there was a known issue that in this configuration, the IP addresses could get lost between the cable modem/router and the Time Capsule. He said it would be best if the Time Capsule was in DHCP/NAT mode and the first device before the switch, this way the Time Capsule was the only device passing out IP addresses.
So I repatched my network like this:
                                                   Motorola Cable modem/router
                                                                             |
                                                   TimeCapsule (DHCP/NAT mode)
                                                            |                                       |   |   |   |   |
                                    Netgear multipart switch                      laptops, Nest, iphones
                                         |         |         |        |
                                           hardwired Macs,
                                             laser printers,
                                               Apple TVs
I can tell you that in the past 24 hours, I haven't seen anything lose a connection. Not even the Nests which seemed be on and off all the time. And, in this configuration, all the devices are on the same network and able to speak to each other.
I hope that helps someone.

So you're saying that Bridge Mode not functioning properly is a well known issue?
Not to me.. I have not had issues with the TC in bridge. And it is my prefered setup. I think it is better as a wireless AP and network hard disk than a router any day of the week.. but there are other ways to skin the cat if it is proving unreliable. I am at the moment using a wireless bridge from the Gen4 TC to a Gen4 AE upstairs for TV internet streaming.. it started off very reliable.. but of late I guess I need to reboot it every few days. And it has required a full reset two or three times.. although I probably need to take some of the blame for those. I am not over worried.. i do not believe in wireless bridges except for the most interim of arrangements.. it will be wired in ethernet ASAP.
Wireless should always be used in a way that respects its status as voodoo.. not stable technology. NOT SCIENCE.. it is more a bag of beads and rattles.
Is there a way to change the cable modem/router to avoid the double NAT problem?
The answer to this may depend on your ISP. Did they provide the modem? If so they may lock it down so you have no control. But normally a Motorola cable modem will not have a bridge mode as such but will have a method of turning off NAT.. (and wireless).. this amounts to the same thing.
Once you turn off NAT.. you need to power cycle the modem so the TC gets the public IP in router mode. The power cycle time might be 5min or 20min or overnight.. it again depends on your ISP.. but you need to stop the modem capturing the public IP so it can be passed to the modem.
Depending on where you are in the world.. US is most concentration of cable network.. you can go out and buy your own modem. Pick one on your ISP list and steer clear of SB.. at least with the apple routers they are problematic.
It also can be a case that the cable modem is SB model and therefore more problematic. Sorry I have forgotten the recommendation for what to buy. There are a number of posts here about it but search is terrible now. (or I am too old to figure it out). I will get Bob to poke his nose in and tell you what works for him.

Time Capsule and time machine with third party router

Hi,
This is the first time I use this site.
I have over three years old Mackbook.
APP has expired.
Now I want to know how to set up time capsule in a new environment.
I moved from Australian and Singapore.
I was using Time Capsule and Airport Extreme in Australia.
I have moved to Singapore.
I am using router provided by Singtell(Singapore Telecommunication). I do not have an Airport Extreme anymore. My housemate and I are using wireless internet-sharing. Needless to say that internet provider is SingTell.
Now I would like to know how to use time capsule and time machine with the network created with a router provided by SingTell.
What I did so far is;
Connected the time capsule to the power point.
Orange lamp lit and flashed for a few second and stop. Orange lamp stayed on.
Apple Utility does not recognise Time Capsule.
I prefer to use it wirelessly.
There are only two USB cable ports installed.
One is used to synchronize iPhone.
Other is used for a printer.
but if it is not possible, wired would be OK.
MacBook 13 inch 2.0 GH Late 2006
I hope that someone able to give me an answer for this.
Cheers,
morepubholidays

In this case the apple support people reveal a truly poor understanding.
You must bridge something.. you either bridge the TC.. which 90% of people do.. or you bridge the dsl router.. which some people do manage to do.. You will have to look that up for your modem and check with verizon if they support pppoe authentication.
IMHO just bridge the TC as you were told not to do.. as they are simply wrong about that.
If you already tried this and it didn't work.. try again.. it is the correct approach.
You have no choice. But this time let me suggest you do it using the 5.6 airport utility.. as the apple toyland v6 airport utility is likely half your trouble.
So here is how to get the utility into your computer.
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. it is very simple.. drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. drill down.. applications utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall 6.1 so don't try.. and you cannot or should not run them both at the same time.. so just ignore the toyland version.. the plastic hammer.. and start using 5.6.. a real tool.
For screen shots see this post.
https://discussions.apple.com/thread/4668746?tstart=0
Then open the manual setup on the 5.6 utility.. go to internet tab. Connection sharing.. off bridged mode.
Select this and update..
Then all your IP addresses will be wrong.. I suspect this is where things are going wrong.. and messing you up.
Once the TC is bridged.. turn off everything and restart.. in correct order.. modem.. TC.. client computers etc. 2min gap between each.

New to time capsule and need help with installing it?

I just bought a new 3tb time capsule and also new to apple routers I want to use this as my new wireless router how do I go about switching this out with my router now. Im using a linskys router now nothing special I think its only a 300Mbps the only problem is that we just had our new house complete and prewired with ethernet connection in every room and a security system that runs off of the router how do I go about switching that set up to the new time capsule? I know if I had to have the company come out to do it they charge a hefty fee which I know its that hard to do the only thing that's stopping me is that set up to the security system I don't want to screw that up???

Three different aspects
1. Set the form up to submit the data (XML or FDF), not the full PDF. You can import the data to the PDF on your end.
2. You can turn on Extended Reader Rights, but then limit the use/users to 500 by the EULA. The applicability of this option depends on your intended application. In a small office, it would be fine. For general web use you would likely exceed the limit and be in violation of the EULA.
3. There may be an e-mail problem, one reason that e-mail is not recommended for form submission (even if the manual discusses it). Again, in a controlled environment like an office it will probably work fine, but in a web setup it is best to use a web script. There are 2 problems with e-mail that both depend on the client system (YOU have no control, but will be blamed in any case). First, the client machine has to be set up as an active MAPI client. Many folks do not have this on. Second, some e-mail clients treat PDFs like text and the result is a corrupt e-mail submission, even if it makes to you.
If you have the possibility of web submission, do it. I suggest only having the form data submitted and not the form.

Setting up Air play with new time capsule and newer airport express?

I just recently purchased a new time capsule, and I'd like to use my current generation airport express to stream music from my apple devices. I just was wondering what I had to do in airport utility to set this up? I was also wondering how to transition the network over from the old express to the new time capsule as far software settings go. I really appreciate the help and assistance. Thanks folks. I'm really looking forward to setting up the network for our new iMac.

Your setup is very easy..
This is how I would do it.
Remove the express from the network.. ie just unplug it but do not change anything in it. Keep the configuration as is until the TC is working.
Power off the cable modem.. this is requirement.. at least 20min is usually needed, dependining on your ISP.
Go into the airport utility and setup the TC as router for your network .. it is a simple setup.. but I would do as stated.. all short names, no spaces pure alphanumeric rather than accept Apple's names. That is for TC and wireless.
After 20min power up the cable modem. Once it is running and you have internet access. you can proceed to setup the express to do the airplay. If the internet still doesn't work, power off the cable modem overnight..
Do not lose that express setup so if you absolutely have to, you can at any time substitute it back and have internet again.
So everything is working properly TC in place as full router.. now hard reset the express.. and simply use the airport utility to put it in extend wireless .. or plug in by ethernet if you are going to hard wire it.
The extend wireless setup is all done straight from the existing setup.
Now you can plug your express audio port into your speaker.. and setup the airplay via the itunes.
I will get Bob to give you his way of doing it.. There is no one RIGHT way .. but he can give you more info if you want a particular method.

I have a time capsule and two air port expresses. The time capsule is in the middle of my house, the expresses equidistant in opposite directions. I would like the expresses to both connect directly to the capsule, but they are connected in serial. How?

I have a time capsule and two air port expresses. The time capsule is in the middle of my house, the expresses equidistant in opposite directions. I would like the expresses to both connect directly to the capsule, but they are connected in serial. How to reconfigure.
I ask because I have music running out of both expresses, and the one that is most distant from the time capsule (routed through the first express) regularly drops the music signal from itunes. And I am guessing the serial configuration of the routers has something to do with this, but my root problem is music dropout - any thoughts would be appreciated.

If you have the the most current model of the Express devices, the default setup is to "extend" the wireless signal. In this type of setup, each Express communicates directly to the Time Capsule.
How did you setup the AirPort Express devices?
What version of the Mac operating system are you using on your MacBook? Or, do you have AirPort Utility installed on your iPad?

SOLUTION TO Time Capsule and extend wireless network using AEBS, Printers..

Hello GUYS
I find the solution: at least I have extended wireless using TC and old AEBS.
: well everybody have same problems to initialize second AEBS, and set it up.
OK follow this steps:
put next to each other TC (time capsule) and AEBS (airport extreme) -> switch AEBS off
If you followed installation TC correctly it should work without any problem.
SETING UP TC PART 1
pres in finder Command + Shift + U =then click Airport utility
set your TC with manual.
On piece of paper record Airport ID:
Click on TIME CAPSULE
I recommend change name not to use deffault long name for TC. Simply call it TC if you want. Set password.
In wireless. Write a name of your Network, keep it simple TC627 what ever. Write it down on paper. security WPA2 personal and password.
Update. and close utility
End of part 1
Part 2:
AEBS setup.
Switch AEBS on: No need to switch off TC
Press reset button for more than 5 sec. so everything is restore to factory settings.
-> in the bar top click wireless and select AEBS. You have to do this otherwise Airport utility will not recognise AEBS.
When you are done. Command shift U
Click airport utility. and manual setup.
-> write down the Airport ID.
Set up your AEBS, name something simple so you know what it is. Password and security.
Here do yourself favor use the same passwords as on TC and security.
NOW ->
click Wireless.
*Wireless network has to be same as on TC.*( it is on the paper)
Select Participate in wireless network
Radio mode b,g compatible or only N it is up to you.
I setup WPA2Personal again with the same password( same on TC)
Click WDS
Select WDS remote
select Allow wireless clients
and now write the TC airport ID into WDS main: number (it is on your paper)
Update.
switch off utility.
no go to right top and change airport back to TC.
Go to manual
Click Wireless:
Select Participate in WDS Network
Click WDS: wds mode to Main
allow wireless clients: and write into WDS remotes AEBS ID, (it is on the paper).
and update.
both airports will restart.
and you are extended.
You made it. Go to Utility Cmd,shift, U and you should be able to see both airports.
Now what you have to do is to take AEBS to different place.
Put it somewhere in second room. Go back to your computer. Leave it for couple of minutes. 10 -15 is ok.
to make sure your TC can find AEBS. If not TC will indicate by flashing green and orange. = >AEBS has to be closer.
correct is that TC has still green light.
Before you start with time machine: read what files to include
hope it helps.

instructions

Extending a network with Time Capsule and AirPort Extreme (via Belkin powerline)

Hello -
I've seen many topics about extending wireless networks here, but none seems to resolve the issue I'm having. I currently have a setup where a DSL cable modem is connected to a Time Capsule and I need to extend this network to another room using an AirPort Extreme.
I live in a very old apartment in Brazil and the walls seem to block the signal from one room to another, hence the need to extend it. Since wireless signal is very weak between rooms, I bought a Belkin powerline AV500 so I could connect both Time Capsule and AirPort using the electrical power at home (just installing a regular Ethernet cable between rooms is not an option).
I started with the basics: configure the Time Capsule + DSL as a standalone network, and it works perfectly within it's range. Then I connected the Belking powerline, plugged a MacBook via Ethernet on the other end and still got very good results (actually better speed than expected). Used it for a while with streaming and other network intensive tasks to make sure it could sustain the connection.
Finally, pluggned the AirPort Extreme on the Belking powerline and this is where the problems started. AirPort Utility 6.3.1 only gives me the option of extending a network wirelessly - it doesn't seem to give me the option of extending it via Etherenet (roaming), which is not good in my case. Luckly I had a copy of AirPort Utility 5.6 which seems to do the job (or I thought so), but it's still not working well.
Although I managed to configure both with the same name, it doesn't seem reliable and some devices (the iPhone 5, for example) are unable to connect and end up with a self-asigned IP address. I'm almost sure I'm doing something wrong on the setup, as I've seen a similar setup working before, so if anyone out there has any clue of what can be done, it will be much appreciated.
Attached the screenshots of both Time Capsule and AirPort Extreme configurations.
Thanks a lot,
-TM
AirPort Exteme:
Time Capsule:

Hello JuliaApple. Welcome to the Apple Discussions!
You have several ways to configure both base stations for what you are trying to do.
The simplest would be to configure the Time Capsule (TC) to "join" (AirPort Utility > Manual Setup > Wireless tab > Wireless Mode = Join a wireless network) your existing 802.11n AirPort Extreme Base Station (AEBSn). In this type of configuration the TC would perform as any other wireless client and not perform as a router. It will; however, still allow for both backups and sharing USB devices attached to it.

About time capsule and external hard disk

I have got rMBP. I also have got time capsule. External WD hard disk is connected to time capsule.
I have got 3 users in my rMBP:
(1) Admin : Administrator
(2) User A : I normally do all my work from this user.
(3) User B: I recently added this new user.
Here, using Finder tabs, User A can see time capsule and External WD hard disk. But, Admin and User B cannot. I also want User B to have the ability to see WD hard disk (and time capsule). For User B and Admin, time capsule does show up, but it shows as not connected. How can I provide User B the ability to see External WD hard disk (since User B needs to store large different files there)? Any permission issue on hard disk?
(Amazingly backup does take place automatically even if I am connected as User B or Admin).
I will appreciate your feedback. Thanks.

Emma1609 wrote:
Hi,
hi emma, and welcome to discussions
Once the external HD is turned on my Time Capsule is not longer recognized. I can't connect to Time Capsule and make any backups. It is also no longer appearing in the Airport settings.
you could try a power cycle on your devices. turn off modem, TC, and HD for, say, 10 minutes. turn the modem back on for 2 minutes, followed by the HD, followed by the TC.
then go airport utility > manual setup > disks. see if your HD is showing beneath the TC

Time Capsule and external Hard Disc

Hi,
I have a problem with my Time Capsule (1 TB) and External Hard Disc (1 TB). The external HD is connected via USB. The idea is to have use the device as a shared HD in my network. First it worked perfect. After upgrading to Snow Leopard i have following problem.
Once the external HD is turned on my Time Capsule is not longer recognized. I can't connect to Time Capsule and make any backups. It is also no longer appearing in the Airport settings.
Can anybody help?
Thank you.

Emma1609 wrote:
Hi,
hi emma, and welcome to discussions
Once the external HD is turned on my Time Capsule is not longer recognized. I can't connect to Time Capsule and make any backups. It is also no longer appearing in the Airport settings.
you could try a power cycle on your devices. turn off modem, TC, and HD for, say, 10 minutes. turn the modem back on for 2 minutes, followed by the HD, followed by the TC.
then go airport utility > manual setup > disks. see if your HD is showing beneath the TC

Time Capsule and Netgear Setup

Similar Messages

Maybe you are looking for