Time Capsule and USB Wireless adaptor for PC

I can't seem to find a USB wireless adapter that I can use to connect my Windows XP desktop PC with my Time Capsule/Airport. I have a Notebook PC that I was able to connect with no problem using my existing wireless PC card. I have tried several USB adapters for my desktop, but nothing sees my network. I've also tried to update to the latest drivers for my adapters. Has anyone else had this problem? If so, any answers?

There is no difference between the TC and other routers as far as networking is concerned. It is fully compliant to the usual standards.
Your wireless USB network adapters should work just fine. A lot will depend on how you have your TC configured. If it is setup for 802.11n only, then if your USB adapters are 802.11b or g, they won't be able to see it. If you have the TC's SSID disabled, they won't be able to see it. If you are using WPA2 and the USB adapters only support WEP or WPA security, they won't work either.
You typically have to find the lowest common denominator and configure everything based on that.

Similar Messages

We use a time capsule as the wireless router for our house. We cannot get service to the whole house. Is there anyway to boost the signal?

We use a 2TB Time Capsule as our wireless airport for the whole house but we can't get the signal to all rooms. Is there anyway to boost the signal?

You to purchase an extreme or express and use it as wrieless extender.. that is the only way Apple provided for boosting the signal.

SOLUTION TO Time Capsule and extend wireless network using AEBS, Printers..

Hello GUYS
I find the solution: at least I have extended wireless using TC and old AEBS.
: well everybody have same problems to initialize second AEBS, and set it up.
OK follow this steps:
put next to each other TC (time capsule) and AEBS (airport extreme) -> switch AEBS off
If you followed installation TC correctly it should work without any problem.
SETING UP TC PART 1
pres in finder Command + Shift + U =then click Airport utility
set your TC with manual.
On piece of paper record Airport ID:
Click on TIME CAPSULE
I recommend change name not to use deffault long name for TC. Simply call it TC if you want. Set password.
In wireless. Write a name of your Network, keep it simple TC627 what ever. Write it down on paper. security WPA2 personal and password.
Update. and close utility
End of part 1
Part 2:
AEBS setup.
Switch AEBS on: No need to switch off TC
Press reset button for more than 5 sec. so everything is restore to factory settings.
-> in the bar top click wireless and select AEBS. You have to do this otherwise Airport utility will not recognise AEBS.
When you are done. Command shift U
Click airport utility. and manual setup.
-> write down the Airport ID.
Set up your AEBS, name something simple so you know what it is. Password and security.
Here do yourself favor use the same passwords as on TC and security.
NOW ->
click Wireless.
*Wireless network has to be same as on TC.*( it is on the paper)
Select Participate in wireless network
Radio mode b,g compatible or only N it is up to you.
I setup WPA2Personal again with the same password( same on TC)
Click WDS
Select WDS remote
select Allow wireless clients
and now write the TC airport ID into WDS main: number (it is on your paper)
Update.
switch off utility.
no go to right top and change airport back to TC.
Go to manual
Click Wireless:
Select Participate in WDS Network
Click WDS: wds mode to Main
allow wireless clients: and write into WDS remotes AEBS ID, (it is on the paper).
and update.
both airports will restart.
and you are extended.
You made it. Go to Utility Cmd,shift, U and you should be able to see both airports.
Now what you have to do is to take AEBS to different place.
Put it somewhere in second room. Go back to your computer. Leave it for couple of minutes. 10 -15 is ok.
to make sure your TC can find AEBS. If not TC will indicate by flashing green and orange. = >AEBS has to be closer.
correct is that TC has still green light.
Before you start with time machine: read what files to include
hope it helps.

instructions

Backup a dual boot iMac with OSX + Vista to Time capsule and USB hard drive

I have just bought a Time Capsule which is now working as my WiFi Network base station and backs up an iMac and a Macbook. The iMac has both OSX and Vista (using Boot Camp) and I was using a USB Hard Drive that has 2 partitions (HFS+ for the Mac; NTFS for Vista) to back up the iMac. Rather than leave this attached to the iMac just to back up the Vista partition I would like to move it to the Time Capsule's USB port and use it as NAS. The idea being that it becomes a NAS with one partition used to back up the Windows data when I run the iMac with Vista and the other partition to archive the Time Machine backups from both the iMac and Macbook. I tried to connect it as it was but got an error and reading the forum it seems that it won't work unless both partitions are HFS+ or FAT. If I reformat the NTFS partition to HFS+ will I be able to use the built in backup function of Vista to back up the Vista partition to the USB hard drive? I read somewhere else that Time Capsule takes care of the formatting for an external NAS drive and Windows will be able to read and write to it even though it's not NTFS. Any ideas comments appreciated.

This is crude but if you need a work around, just plug the USB drive directly into the iMac.. copy the files to it.. then plug it into the TC.
You also do not need to use the TC as an intermediary between your iMac and MBP.. just turn on sharing in the computer.. so you can directly copy files from one to the other.. Macs have public access directory preconfigured for each user account.
As far as mounting the TC..
In finder use Go, Connect to server.. and type.
AFP://TCname or TCipaddress
Where TCname is the actual name of the TC.. I strongly recommend you follow SMB network rules.. ie if your TC has a name like
Fred Blog's Time Capsule 2445566.
It is too long.. it has spaces and it has non-alphanumeric characters.
Shorten it to FredTC
No spaces no characters that are NOT alphanumeric.
TCIPaddress is simply the standard IP.
You can also use CIFS://TCname which according to the article forces the connection back to SMB1 rather than SMB2 which as usual is broken.
But I would definitely use AFP if possible. I cannot understand the decision to move to SMB as standard.

Using Time Capsule and External FW Drive for TM Backups

Wondering if this can be done, or if anyone is successfully doing it.
Here's what I want to do:
Use a 1TB Time Capsule to backup wirelessly and a FW800 external drive for speed in case I need to reinstall. Therefore having 2 backups? I've been down the road of using SD (cloning) and am ready to move on to another backup strategy. Cloning works fine but it dedicates a drive 100% of the time where TM doesn't.
One thing I did with an old 2.5" 80GB HD in an enclosure that I like a lot is put 10.6.2 on it along with Disk Warrior 4.2, Tech Tool Pro, and Drive Genius to use as a startup and repair disk.

D/FW wrote:
Use a 1TB Time Capsule to backup wirelessly and a FW800 external drive for speed in case I need to reinstall. Therefore having 2 backups?
You can do that, but not simultaneously. TM only has one destination a a time; you can back up to the TC, then select the external HD via TM Preferences, then switch back.
I've been down the road of using SD (cloning) and am ready to move on to another backup strategy. Cloning works fine but it dedicates a drive 100% of the time where TM doesn't.
I don't know what you mean by that. I use CarbonCopyCloner (similar to SD) in addition to full TM backups, so I have two separate, independent backups, on two separate drives, and get the advantages of both. You can partition an external drive (but not a Time Capsule), so you could have your clone on one partition, and other things in one or more additional partitions (I do that as well). As long as the "clone" partition is the same size as your internal HD (or at a minimum, at least 15% larger than the amount of data on it), you can use the rest of the space for anything else.
See #5 in the Frequently Asked Questions *User Tip* at the top of this forum for detailed instructions on setting-up a drive for Time Machine. The same procedure works for setting one up for a clone and other partition(s), too.

Time Capsule and USB HD

I have two iMac running Leopard 10.5.6 and Tiger respectively. Both iMac share Internet connection via a Time Capsule and Time Machine has been running properly. I have a NAS connecting to the TC too.
As my NAS is nearly full and I intend to buy a large HD to replace the NAS. I am a bit confused if I should connect the new HD to the TC via USB or just buy another NAS to replace the old one.
Question:
Can I use the HD inside the TC to serve two functions (i.e. backup of the iMac via Time Machine and NAS) and connect a new HD to the TC for backing up all the data on the TC.
Would someone pls let me have your advise. Thanks in advance.

After even more research I don't think that this is possible (yet). I really hope that this will work in a future update of Time Machine, because this is one of the reasons why I bought it. Still a great device though, loving it.

I have working Netgear network. Want to add new Time Capsule and run 2nd network for new apple TV and Imac, and keep the netgear network for my PC and Canon printer.

I have working Netgear N600 dual band router network. The existing network has an XP netbook PC, canon printer, 2 Iphones, Epson Air printer, an Ipad, 3 roku boxes, backup drive. Just bought a new Apple TV box, and time capsule 2T. I have an IMac on order but don't have it here yet.
My goal is to add new Time Capsule and create 2nd "apple" network for new apple TV, Iphones, Ipad, Epson Air printer and new Imac, and keep the netgear network for my PC, Roku TV boxes, and Canon printer and backup drive.
The Netgear router, the time capsule and new IMac will be on the same desktop, I dont need to backup my netbook PC to time capsule.
Where do I start?
Which device connects to my modem first, the TC2 or the Netgear?
Is it best wait for the Imac before starting or can the TC2 be set up from my Ipad or PC?
Thanks.

It is pretty simple..
Setup the TC in bridge and plug it into the Netgear.. I would leave the netgear as the main router for now, although in the future you can swap things around. The netgear firmware may have issues with bonjour and airplay/airprint?? Does your ipad print ok now?
You can setup the TC using Mac, PC (at least up to win7) or iOS.. they all have airport utility available.
Bridge mode is set differently depending on the version of the utility. This is v5 and how the windows one will look (at least similar to).
v6 will be as
With the TC in bridge you will still create a wireless network.. and give it a different name from the netgear.. then all the apple devices can connect to it. Use ethernet rather than wireless if the imac is on the desktop with it. Much faster and better for using Time Machine backups.
If you run into any issues.. just post the particular issue. It will take a bit of getting used to, but isn't hard.

USB Wireless Adaptor for eMac

I still have to check them out but I do not believe the eMacs in question have a built in wireless option. I am told they are running OS 10.3 and I was looking for recommendations on adding wireless to about 10 eMacs for a teacher that wants them networked but the classroom does not have any available network ports to even plug in a network switch too. USB wireless adaptor would be good unless I have to use an internal Airport card or something I guess that is fine.

Check out the eMac specifications, for example, here. Depending upon the model, you could install an AirPort or AirPort Extreme card. This is probably the easiest way. See also the KB articles HT1621 and HT3024.
You could per se try USB wireless adapters, but only if appropriate Mac drivers are available (if at all, usually only for Mac OS X 10.3 or higher).
Another solution could be wireless Ethernet bridge devices (also called gaming adapters). These units (such as Belkin F5D7330, D-Link DWL-G810, D-Link DWL-G820, Linksys WET54G, Linksys WGA600N and Netgear WGE111) do not require special drivers and can be used under almost any operating system. Not all models (or versions of a model) offer WPA security. You could connect a wireless Ethernet bridge directly to each computer (the Ethernet port). Alternatively, it ought to be possible to use wired Ethernet (via a switch) between the computers, and then one bridge device as a connection point to an existing wireless network.
Jan

Can Time Capsule be the wireless router for my MacBook Pro and my iMac G5?

My MacBook Pro was simple to hook up to Time Capsule, but now my iMac G5 will not connect to the internet. Any ideas?

Hello bluefeather. Welcome to the Apple Discussions!
How do you have the iMac G5 connected to the Time Capsule (TC) ... by Ethernet or wirelessly? If wirelessly, try connecting via Ethernet ... can it access the Internet now? What version of OS X are you running on the iMac?

Time Capsule and FiOS wireless router

Can I connect the Time Capsule to my FiOS router and then disable the wifi feature on the FiOS router?

Are there any known issues with the TC in general, particularly from the wifi perspective?
TC is much better than it was.. make sure you keep it cool.. place it up from the bench on a couple of pencils.. that stuff about conductive rubber.. ignore it.. rubber in all its forms is an insulator and holds in heat. If it does start running really hot.. it has a fault and you should take it back.. Same with hard disk.. they occasionally go bad.. so backup to it.. fine.. storing files on it.. no don't do it.
Remember it is covered under your computer applecare.. so if you have any computer with extended applecare it will cover TC with certain conditions.. but that gives the TC effectively 3years warranty.. after that.. dispose of it and buy a new one.. the TC is not going to be reliable as the hard disk has been starting and stopping multiple times every day for 3years.. just don't trust them.
Wireless is ok.. I don't think it is particularly good range wise. Although Apple said how much better it was than previous Generations.. I have had all 4 now.. and performance in my experience was line ball between all of them. Apple design their routers to work very well with AEBS or AEx so if you want to extend wireless it is simple.. just it doesn't work with any other brand.. apple now reflecting a rather dark empire tendency.. they used to critize in others.
Clarification question...how do I backup my current files on the Lacie to the TC? Would that simply be connecting the two devices via USB and copying over?
Backing up TM files?? Not a good idea.. TM works differently on local disks and network disks.. and TC is best left to do its own stuff. If you mean moving actual file storage.. don't. The TC is not a file store.. it is a backup target.. TC has no way to back itself up.. and TM cannot backup a network drive .. so you would have to buy 3rd party software anyway.
Also USB on the TC is purely for printer and USB connected disk.. but you cannot directly copy from one to the other.. it would have to copy over network to the computer and then back to the TC.. it will be 2x to 4x faster if you do want to copy files to use Lacie plugged into the computer.. and copy to the TC. At least files are only going one way.

Time Capsule and Extreme Wireless network BROKEN !!!! PLEASE HELP

Hello All,
Anyones help on this would be greatly appreciated I am actually starting to loose sleep over this issue.
I have a Mac Mini Server (MM) running Lion (it's a storage thing), 1st Generation Time Capsule (TC) and a Airport Extreme (APX) the first one of the square TC looking one).
So due to living with friends I created my own little network, the MM is upstairs in my room with an ethernet connection to my TC for a quick backup and then downstairs the APX is plugged into the router (Sky Broadband), created myself a little network everyone was happy.
I had to move out for a few months took all the apple gear to the new house plugged everything PING!!!! there is my network, not had to do anyhting make any changes or anything the only thing different was the APX was plugged into a Virgin Media router.
So I moved back after a few months to the place mentioned in paragraph 3 and it has all gone belly up in a mojor way. The network I had originally built is no longer visible, I could not find the devices in the Airport Utility bad times all round. I did a soft reset on the TC and a soft reset on the APX nothing! I did a hard reset on the APX and a hard reset on the TC nothing!
I have used an ethernet connection between the TC and the APX and can pick up both of the devices (happy days you think), go through the montions in Airport Utility setup the devices and a new wireless netwrok whihc is then exteneded, then unplug the ethernet cable BOOM the devices are nolonger seen in Airport Utility.
The interesting thing is I can still the the network created on the TC and the APX on the mac, iPad and iPhone but when I try and connect to the network (whihc has full signal stregnth) I either get a conection time out error or a unable to connect tot he netowkr error.
Please, Please, Please can somone help, I am not aware of any major updates, damage, droppage of kit or anything.
Kind Regards,
Ray

The bottom line here is that it is always a good idea to reset your routers back to factory default settings and re-configure the network again when you make a change in location or in Internet service providers.
That's the best advice that I can offer for your current issues.
True, you could go with a "try this, try that" approach and possibly get things working that way. but this will likely take a lot more time and produce more headaches than simply starting over again.
Of course it is possible that you may receive other advice that tells you exactly what to do in a few simple steps...,so depending on your schedule to get the network back up and running, you may wish to wait for other suggestions.

Best way to secure a Time Capsule and it's files for a house rental.

We're renting our house and have a time capsule that we use for backing up our MacBooks and for our network. We'd like to keep the network available to our renters (as well as the airplay speakers on a couple different APExpress's if possible.) Any suggestions on a set up that would give us a bit of peace of mind regarding our data safety?
Thank you!
J

Thanks Bob,
I will go that route then. Attached below is screenshot of my current setup. I plan to swap the Extreme with the Time Capsule so that it would be in a deadbolted/secure room. Those two are currently connected with Ethernet cable (CAT6) to improve the network's stability. Could I keep the Extreme and TC hardwired this way or would it compromise things? Any other network settings I should make sure are in place other than the separate admin and wireless passwords?
Thanks again!

Is time capsule the only wireless backup for a macbook pro that will work with Time Machine?

I just got a macbook pro (mid 2012) and I was going to back it up, but the time capsule is very expensive so I was wondering if any other backups worked wirelessly with time me

Any external hard drive can be used for a Time Machine backup, but for network backup I doubt you will find much if anything at a lesser price than a Time Capsule. Plus, the Time Capsule is also a network router.

Time Capsule and Existing Wireless Network

I've previously used time machine to back up my G5 & Powerbook to separate external hard disks. I've just bought time capsule so that I could back up both computers to the same drive.
However, when powering on the Time Capsule device it is not visible on my existing network (called Wireless LAN) and instead it seems to have created a separate network called Apple Network b73829.
If I switch to this network I can see the Time Capsule device and it is also visible in Time Machine preferences but I cannot access the internet or any of my other wireless devices (Extreme Base Station etc.) which form the Wireless LAN network; I must switch back to this network if I want internet access.
What I don't want to do at this stage is replace my existing base station with the time capsule device; I just want to use it for backing up wirelessly.
I have reset the device several times now but it just will not join this existing network - what am I doing wrong?
Many thanks & regards,
Cliff
Brighton, UK

OK, so I have done this and it's made no difference. The new network Apple Network b73829 is still present alongside Wireless LAN.
I can only access Time Capsule if I switch to the new network, with the resulting loss of internet access from my Powerbook and, if I switch back to Wireless LAN I regain internet access but cannot see Time Capsule.
Although I just want to use Time Capsule to back up I have tried to connect it to my wireless LAN using the Join Existing Network on Airport Utility (even though I've been told I don't need to do this for Time Machine) but it has failed each time. After entering the password and wireless password information etc. and pressing update the Time Capsule device does re-start but there is ALWAYS an error message that says the device cannot be found and I should check that I am close to it (it's 3 feet away) or I should connect via Ethernet. If I connect via Ethernet it seems to disable the wireless functionality that I bought the device for.

Time Capsule and Leopard - wireless dropouts

I bought a new 24" iMac (Leopard) and Time Capsule 8 weeks ago, and set up a wireless network which also included my old 17" G4 iMac (OSX 10.3.9) with Airport Extreme card.
From the very start I was having annoying, small problems with wireless dropouts on my Leopard iMac - sometimes it could find the TC, sometimes it couldn't. I decided that for my first Time Machine backup I should move the TC closer to my Leopard machine - it appeared to be an improvement, so I left it closer for a week or so. I then decided to move TC back to it's original position and had good connection for another month or so.
This week, my wireless connection (Leopard to TC) has been steadily deteriorating until tonight I have been unable to get any wireless connection at all.
I haven't been able to successfully use Time Machine for weeks.
The whole time I have had excellent, constant, trouble free connection between my old iMac and TC.
I've looked at forums and tried a few suggested fixes with no success - it's hard to describe how frustrating this is (I'm typing this on my old machine) as I have a number of online musical projects in progress which require daily, often hourly exchange of files.
Surely Apple must have a fix for this!
The problem is clearly not the TC, but more likely Leopard. I spent a fortune upgrading and am now completely dissatisfied after being a happy Mac user for many years.
Does anyone have a surefire remedy for this? I really can't believe that there isn't one available.
Rant over,
HH

It's likely your wireless network. Check this thread on cordless phones and TC.
http://discussions.apple.com/thread.jspa?threadID=1679559&tstart=0
Welcome to Apple Discussions!

Time Capsule and USB Wireless adaptor for PC

Similar Messages

Maybe you are looking for