Time Capsule as Wireless Ethernet Bridge

<noob>
So I picked up the Time Capsule to handle things with my MacBook. That means I now have a wireless N router (dLink DIR-655) kicking around. I want to try to use it to get wireless N to my Xbox in another room.
Sadly, the dLink router doesn't seem to be able to bridge, so I've used it as my primary router (connected to my modem).
How can I get my Time Capsule to hop on the existing wireless network, and then use the ethernet cable to connect the TC to my Xbox?
MODEM--(wired)-->DIR655--(wireless n)-->TC--(wired)-->Xbox
Note that I still need my PC (hard wired to the dLink router) and my MacBook (wireless to my dLink router) to see the TC for hard drive storage.
Bonus points if you can figure out having the one dLink network serve only the TC, and having the TC broadcast a new network for the MacBook and my iPhone, while still serving the Xbox on a wired connection.
</noob>

Welcome to the discussions!
I'm afraid we'll get no bonus points since products from different manufacturers are rarely compatible for bridging or extending a wireless network.
While the Time Capsule could be configured to "join" the wireless network of your D-Link router and backups would occur over your current wireless network, when it is setup this way, all routing functions become disabled. This means that the ethernet ports are not enabled and the Time Capsule does not provide any additional wireless coverage.
It's not possible to configure the the Time Capsule to "extend a wireless network" with your D-Link router since this function only works if you have another Apple "n" device setup as the main router on your network. (When the Time Capsule is configured to "extend", it provides additional wireless coverage and the ethernet ports are enabled.)
If you want the Time Capsule's ethernet ports to be enabled and you want it to create a wireless network for more coverage, you'll need to connect the Time Capsule to your D-Link router using an ethernet cable. Or, if this is not possible, you might consider a pair of ethernet powerline adapters to accomplish the same task by utilizing the AC wiring in your home.

Similar Messages

Using Time Capsule to Wirelessly Receive Internet and then Extend Network via Ethernet

Hello,
Our modem/router combo is located downstairs, and my computer that i want to get online is upstairs. I cannot get a ethernet from the modem to my computer to access the internet, so I wanted to try to use my Time Capsule to help me get online upstairs (not sure if this is possible...)
My idea was to have the Time Capsule receive the wireless signal and then connect the computer to the Time Capsule through an ethernet so that I may get the computer online. Essentially wireless connection in, wired connection out.
I've been playing around with the device for a while now, and can't seem to make this work. Has anyone used the Time Capsule in this fashion? Is it even possible? If not, does anyone have any suggestions on how to get my computer online?
Thank you very much for any help/input!!

Why not try a pair of these over domestic power loop.
http://www.netgear.com/home/products/powerline-and-coax/high-performance/XAVB510 1.aspx#two
Not cheap though Best buy link
http://www.bestbuy.com/site/NETGEAR+-+Powerline+Ethernet+Adapter+Kit/5042106.p?i d=1218603011817&skuId=5042106
The Apple solution might well need Two devices to extend range.
You would retain your ISP router/modem however would go into settings and TURN OFF wireless on that device - you can do this in the Java Web based control panels on most routers.
Now you sling the Ethernet cable between that router and a purchased Time Capsule device locally and set this up to create a new local Wifi network (Replacing that of the ISP supplied router) . Being a dual band device and being able to broadcast both over 2.4 Ghz and 5 Ghz frequency base bands simultaneously you could well see improved performance and range straight away.
However if not then you are going to need a further device an Airport Express set up in bridged mode somewhere between the Time Capsule and your upstairs rooms. Your may have to try various power points and locations to get coverage required.
Further Airport Express devices can be added in bridged mode as required to cover blind spots, however remember each additional device degrades the overall network performance somewhat.
Again this will get quite costly.

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme. Can my network operate properly to extend the network with both a wireless and wired extend functionallity?

I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
Excellent plan.
Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
This Apple support document will show you how to hookup and configure the second AirPort Extreme:
http://support.apple.com/kb/HT4260

HT4259 Direct Connect Two Time Capsules together with Ethernet.

I have TWO Time Capsules ( One upstairs providing Time Machine backup to IMAC #1 ) and (One downstairs providing Time Machine Backup to IMAC#2)
I would like to extend the wireless network portion of this to reach the whiole house with ONE wireless network. I know I can EXTEND the network, but my question is can Connect the two time capsules together via Ethernet cable ( my house is pre wired). This will essentially ensure that the two devices have a solid connection instead of relying on WIRELESS.
Any reasons to NOT do this?
Time Machine will be used differently on the two devices.
Thanks
Ron

Hello!
I have the same problem, i am trying to do this
Timecapsule nr 1, ISP uplink to WAN.
from this one i have LAN to the other timecapsule to WAN.
On the first timecapsule i have DHCP/NAT enable.
On the second i have, Bridge mode.
But when i am connected with eth to the second one i wont recive dhcp addresses or anything... like it wont passtrough.
Any ideas?

Can i use my time capsule as wireless storage and not as a router too?

hi there i just bought my self a time capsule its a 500gb one as i do not need the 1tb+ storage.
i play a lot of online games and have a fast router so i do not want the time capsule for its router capabilitys i only want to use it as a wireless storage unit is this possible to do?
if not i can connect a usb storage to my current router and use that as my wireless storage if so where is the best place to sell this time capsule?

You simply bridge the TC and plug it into the existing router.. it will then provide network storage..
Can connect either via the existing router or the TC.. if you set up wireless correctly.. if it is a gen1 you can set to 5ghz only.. that will keep it from interferring with the existing router.

Can i use my time capsule to wirelessly backup my macbook and its external hard drive, which up until now was it's time machine and storage? How?

Can i use my time capsule to wirelessly backup my macbook and its external hard drive, which up until now was it's time machine and storage? How?

The external drive must be connected to the Mac using either USB or FireWire
You must remove the external hard drive from the list of items that are "excluded" from backups in Time Machine Preferences.
Here's how:
Open System Preferences (gear icon on the dock)
Open Time Machine
Click Options
Look for the name of the hard drive in the list of "excluded" items and click on it to highlight it
Click the -- (minus) button at the bottom of the list to remove the hard drive from the list of "excluded" items....so it will now be backed up
Strongly recommend that you do the first backup using Ethenret from your computer to the Time Capsule since the entire contents of the external drive will be copied on the first pass. Ethernet will be 3-5 faster than wireless.
Once you have the first backup done, you can use wireless for subsequent backups since they will nornally be much smaller....unless you add large files to the external drive.

Is the apple time capsule a wireless router

is the apple time capsule a wireless router

Yes, it's a 802.11 a/b/g/n (pretty much all the popular wireless standards). If you get the latest generation, it will also give you TWO wireless networks - the main one for you and a guest network. It has dual bands so that your guests can connect outside of your network.
It also has 4 Ethernet ports on the back to connect non-wireless devices.

Can i unplug time capsule from the ethernet cable and still use it??

can i unplug time capsule from the ethernet cable and still use it??

I have tried to extend that wireless line but as soon as i remove the LAN cable i have no internet connection anymore. So basically, does the TC get the signal wireless from the router??
The Time Capsule can wirelessly extend a wireless signal....but only if it is being provided by another Apple AirPort wireless router.
If the "main" rotuer there is not an Apple AirPort router, you will need to connect to the network using a wired Ethernet connection.

How to use time capsule for wireless back-up but not internet?

Hello,
I have a tower and recently a laptop at work. The tower is connected to our local network with an ethernet cable and the laptop with wireless. So, the internet connection is fine for both.
I was hoping to use my time capsule to do time machine backups on my laptop. Do you have any advice on how to configure this? I do not want to use the time capsule to extend my Internet, as I believe my work I.T. would prefer to handle all access to their network.
Perhaps there is some documentation about doing this that you could point me to? I have not been able to find it.
Thank you for your help.

Your original question was How to use Time Capsule for wireless back-up but not Internet?
There is no reason for you to connect the tower....or anything else...using Ethernet if your goal remains that same as you stated.
If you are asking if you can backup the Tower using Ethernet, and not wireless, then you can connect the tower to one of the LAN <-> ports on the Time Capsule....not the WAN port.
Yes, it appears to work without plugging into my tower.
Correct, it will work.
I just have to select the network that it created. Of course, I have no access to the Internet while this is happening and it can not auto backup, unless I am on that wireless signal.
As I stated, that is the downside to trying to back up without an Internet connection. You have to establish another network...and backup over that network.
If you are asking if you can stay connected to the work network while also backing up to your non-Internet "private" network, that is not possible.

My situation is two separate buildings 100 feet apart. can time capsule provide wireless internet in both?

can time capsule provide wireless internet service between two homes 100 feet apart?

OK.. starting to get the picture..
You should have run ethernet between the two buildings not cable.
Does the cable for the second building start inside your house.. ie do you have a termination for cable or does the second building come in directly from the street.
If you have cable link between the two buildings you can buy ethernet to cable adapters.. plug one it at each end and simply extend by plugging it into the router on the main cable link.. simple and far superior to wireless.
Otherwise you need to work out what kind of budget you want to spend to do this..
You can buy professional or semi-pro stuff from companies like ubiquiti which are far superior to domestic wireless link.. or if you want to do it on the cheap figure out what is the min speed you can live with.
I can give you instructions for using a pair of old airport.. in WDS.. or new ones.. but the new ones will cost far more and no gain.. you can usually pick up the old discus ones for $10 on ebay and they work great.
But don't try to do it without a link.. ie a specific set of AP in one house plus repeater in the other. As anything you do without making a link will just fall down or become unreliable.
You must have a pair of matched items.. You want to do this with WDS.. and you want something with good range. If you want N wireless that is fine.. but buy a pair of N wireless routers that can do WDS with full WPA2 security. eg full N wireless edimax stuff is not bad. TP-Link also not bad.. but if you want to run airplay and bonjour etc.. anything apple network then stick to apple. You will find that non-apple wireless routers will often not work with apple specific protocols.. as they are just that.. non-specified.

Can a time capsule work wireless

Can a time capsule work wireless

iOS devices like the iPad and iPhone back up to iTunes on your computer.....or.....to iCloud.
They do not and cannot back up directly to the Time Capsule.
If you then back up your computer to the Time Capsule, all the backups in iTunes are backed up on the Time Capsule....in case your computer hard drive fails, is stolen, etc.
Your computer can back up to the Time Capsule using wireless or via an Ethernet connection.
See this Apple support document for all the information on how iOS devices back up.
http://support.apple.com/kb/ht1766

Time capsule not wireless just external back up

I just want to use my time capsule without juggling with the wireless network in my apartment.
Is there a way to plug it into my Imac liek the old external hard drives adn just back everything up?
I am not tech savvy, so anyone who is patient and can answer this, please be simple.
Thank you in advance.

It can only be used with your computer as network storage either using Ethernet or Wireless. Connect an Ethernet cable from one of the LAN ports on the Time Capsule to the Ethernet port on your computer. Configure Network preferences to use Ethernet instead of wireless.

Time capsule 2 wireless networks one without internet

Hi
i have a airport extreme and time capsule setup via ethernet to extend the network in the lounge room - i have setup a wireless network which has full internet access
my question is >> , does anyone know how to setup a second wireless network (without internet access - so it can be used for watching movies from a my cloud hdd via the my cloud app - ) so basically a second wifi network with only wifi -no internet ?
Is this possible ?
thanks

Yes, it is possible.. but you will need another wireless router to do it.
Setup the wireless router as a Static IP device running DHCP and running a different wireless name to the apple routers. You will need to swap your device that is watching the video from the airport network to the new network to watch the movie.
This could be done better with a more sophisticated router.. Apple provide no functionality beyond the most basic but lots of routers that allow you to run secondary IP and vlan will allow this without needing multiple networks.. For now though it is easier to just get a cheap wireless router.
Even an Apple router can do what you want.. just set it up as router without a WAN connection.. something like a Gen5 AE would work well and fairly cheap.

Dual RAP Mesh Network vs PTP Wireless Ethernet Bridging to provide link redundancy

Currently looking at a few options to optimize a current point-to-point wireless LAN-to-LAN connectivity shot for a wired customer site for better redundancy (hardware diversity and/or logical path diversity). Currently the customer is fed via an older solution, using two Cisco 1522 APs with Cisco Aironet 14-dBi Path Antennas (AIR-ANT5114P-N) for a 5-GHz PTP wireless ethernet bridge (under 3km), in which one 1552AP hangs off a L3/L2 Distro switch and the customer's 1522AP hangs off a 3750X switch, which has another access switch hanging off it via a fiber run of about 2km, which is exposed in parts and can't be re-run again due some limitations.The customer doesn't utilize any wireless services. Due to their location, we can't connect them to our wired distro infrastructure directly via fiber.
Looking at setting up two wireless shots (instead of just one currently used); 5-GHz point-to-point bridges using upgraded gear: Cisco 1552EU APs with Cisco Aironet 14-dBi Path Antennas (AIR-ANT5114P2M-N) or straight Exalt r5005 solution. The PTP shot will hang off two seperate distro switches for redundancy purposes, pointing toward the customer site at two seperate locations, spaced apart by approximately 1 to 1.5 km, so that they aren't at the mercy of being isolated on one side if they have another fiber cut which connects their two main access switches together. If need be, we can hang two main APs on one distro facing two APs at the customer site, since this would create some redundancy, just not the same level as above.
The below is what I'm really unsure on.
Possibly looking at setting up a mesh network using Cisco 1552E APs with 2.4 GHz Omni-directional antennas (either a 2.4/5GHz Terrawave MIMO Omnidirectional antenna or Cisco AIR-ANT2547V-N antennas, which ever is best) with two RAPs, one RAP hanging off one distro and the other RAP hanging off another distro for hardware diversity, both under the same bridge group name and both RAPs hanging off the same WLAN management SVI subnet on the distros. The customer site will have two 1552E MAPs located at two seperate sites, as pointed out above. I don't think a third AP would be needed, since they don't use wireless services. Since there would be only two RAPs, not three, would it be best two set-up this with both RAPs on the same channel to minimize convergence time should the mesh transfer from one RAP to the other RAP, as long as both RAPs are spaced apart under ???? distance to avoid interference/other issues? Looking at some documenation, it appears you can have a MESH network, as long as your MAPs and RAPs fall within a 2 mile range area, preferably closer to a 1 mile range area (for better bandwidth & reliability). This solution has been brought up as possible dual-homed solution in theory, by virtue of having two more more MESH APs fall within the range listed above, to the RAPs. From a layer 3 perspective, I'm not sure what the most optimal idea to run with in this scenario set-up would be. Possibly set-up two seperate user SVI VLANs (for their data services), one placed on each access switches these MAPs will hang off at the customer site, & using the same management SVI subnets as the RAPs for the wireless managment side (for accessing the APs). From my understanding, the user data SVI doesn't matter from the perspective of when the mesh transfers from one RAP to another, it should be transparent to them. The distro switches will just have the management SVIs placed on them for the RAPs, the user SVIs will be placed local on the access switches only. And all APs will hang off access ports set to the management VLAN ID.
In my opinion, the PTP 5-GHz, dual distro homed solution makes the most since for wired client access, but since the latter option was brought up, it has to be weighed - plus I'm curious if it can work.

The Exalt r5005 works great for redundancy PTP links. You have to use the sync cable between the two co-located bridges and also set the polarization on the bridges. You can then use routing or spanning tree to decide traffic path. With mesh, you will have to make sure you set the parent or else the maps will keep switching perhaps.

Labview 2011 always disconnecting over wireless Ethernet bridge!

Hello, we recently upgraded from labview 2009 to labview 2011. We use a Labview cRio-9014 and FPGA backplane 9114. For connecting the cRio to our laptop we use Digi XPress Ethernet Bridge: Multipoint 900MHz industrial wireless part# XEB09. This program worked over our wireless link running labview 2009 with the old cRio software.
After upgrading the desktop, upgrading the cRio's software and recompiling the FPGA code we tested our setup via a wired ethernet connection and ran it all day with no problems. However once we switched to using our wireless ethernet bridges the cRio disconnects always 2-3 minutes after starting. It also does not allow us to reconnect without powercycling the cRio. The radio modems show a solid connect and no problems the whole time. Now I've searched through known issues and all over the forums without finding anyone having a similar issue so I hope someone can chime in and let me know if something else in LV2011 changed or what.
My current hypothesis is that labview 2011 uses UDP packets for status/keep-alive and our radio modems are not guaranteed to recieve all UDP packets. Please correct me since this is only a guess and I don't know what's going on under the hood on the cRio side.
P.S. I've captured the packet data using WireShark on the laptops side from deployment until disconnection but can't find any obvious problems. It's a fairly large file so let me know if it's needed and I'll try to find a way to upload it.
Hopefully someone can help.
Best Regards,
Sam Bingham
Great Lakes WATER Institute

Our host OS is WIn7-64Bit, and XP-32bit but they all display the same behavior.
cRIO hardware: cRio-9014 and FPGA backplane 9114
Our system is has 4 modules installed NI-9205, NI-9401, NI-9401, NI-9870, although we are only using the serial ports on NI-9870.
I looked for the NI TimeSync to remove but it isn't listed in our installation
Contents of current installation:
CompactRIO Support 4.0.0
DataSocket for LabVIEW Real-Time 4.9.0
HTTP Client 1.2.0
HTTP Client with SSL Support 1.2.0
I/O Variable Remote Configuration Web Service 1.0
LabVIEW 2011 Adaptive Filter Toolkit 11.0.0
LabVIEW PID and Fuzzy Logic Toolkit 11.0.0
LabVIEW Real-Time 11.0
Language Support for LabVIEW RT 1.0.0.4
NI Application Web Server 2.0
NI System Configuration 5.0.0
NI System Configuration Network Support 5.0.0
NI Web-based Configuration and Monitoring 2.0.0
NI-RIO 4.0.0
NI-Serial RT 3.8.0
NI-VISA 5.1
NI-VISA ENET Passport 5.1
NI-VISA ENET-ASRL Passport 5.1
NI-VISA Remote Passport 5.1
NI-VISA Server 5.1
NI-VISA USB Passport 5.1
Network Streams 1.1
Network Variable Engine 1.8.0
Remote Panel Server for LabVIEW RT 4.0.0
Run-Time Engine for Web Services 4.0.0
SSL Support for LabVIEW RT 4.0.0
System State Publisher 2.0.0
Variable Client Support for LabVIEW RT 1.8.0

Time Capsule as Wireless Ethernet Bridge

Similar Messages

Maybe you are looking for