Time Capsule conection

the company changed my cable moden and now my time capsule is not working any more. please help me to make it linked again.
tks
JF

Factory reset the TC and start over.. this is important.. the TC remembers too much from the old network.
I have no idea how old your TC is.. here are the general instructions.
The Factory Reset TC Gen1-4. Or AE Gen1-5
Unplug your TC/AE. Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec.
Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
Factory reset TC Gen 5 or AE Gen 6
Hold in reset for about 5sec until the status light flashes quickly.
If your AirPort AE or TC still doesn’t respond, do a similar reset to the Gen1-4.
Unplug your AE/TC .. hold in reset and power the TC/AE back on.. without releasing the reset.. wait until status led flashes rapidly.
Redo the setup of the TC.
If your modem is a pure cable modem.. the TC must be in router mode, that means it shows dhcp and nat on the network tab.. but the normal setup wizard should get it right.
If your new modem is also a router, the TC must be in bridge mode.. that means it shows Off (Bridge Mode) in the Network tab. Sometimes the utility gets that wrong in the automatic setup.. no worries.. allow the automatic to do what it wants then manually change it.
Tell us if you run into trouble or need help on a particular setting.. the more details you give the easier it is to help.

Similar Messages

How do I set up a network using time capsule

I have a 2TB time capsule and an airport express, however I would like to move my capsule to another room where I want to connect 2pc's, which do not have wireless adapters and connect them via Ethernet to the capsule to allow them to go online. My printer is in this room currently connected to airport express to print wirelessly, but I want to put my airport back on my stereo.
In addition I want to continue backing up my iMac, wirelessly, the problem i am experiencing is the time capsule needs to be connected to the router via Ethernet.
Moving the capsule to the other roodoes too far, without a direct route to run Ethernet cable.
Can this be done? Any help is very much appreciated.
Cole

Hi Bob,
I have an O2 router wireless box 5
In short what I would like to acheive is;
iMac - wireless connection, wireless printing, wireless back up to time capsule
Time Capsule - conect to printer via usb and to connect 2 pcs via ethernet to use Internet and print
Thanks for looking into it for me
Cole

Airport Extreme Upstairs conected via switch and cat6 to time capsule downstairs. Is it possible?

I have used an airport extreme connected to my cable modem for a while. This is upstairs in my office. Reception downstairs in my den was spotty at best. I had a time capsule I was no longer using, and set it up downstairs as an extender. This some what worked, but the reception was still hit or miss. I have now wired my house with Cat 6, and have a switch set up in my office. My question is: Is there any way to hard wire the time capsule in with the wired network, but still have it extend my wireless network? I would also be ok if it had to be a second wireless network all together. I forgot to mention, any time I hook the time capsule up to the network, either through the WAN port or one of the others, it seems to crash the network. Thanks!
The set up is as follows:
Cable Modem - Airport extreme - Switch - wall - Time Capsule (I hope). Any input would be appreciated.

OK, thanks for the info.
I assume that you have verified that the Ethernet cable is working at the end where the Time Capsule will be located. If not, temporarily connect the Ethernet cable to the laptop and turn off the wireless on the laptop.
Make sure that you can get a good Internet connection that way, which will verify that the Ethernet cable is working.
If you cannot get a good Internet connection this way, do not proceed until the issue has been resolved. Turn the wireless back on at the laptop when you are done with the testing.
With the Time Capsule powered on for a few minutes...but the Ethernet cable not connected yet....hold in the reset button on the back of the Time Capsule for 7-8 seconds and release. Allow a full minute for the Time Capsule to restart to a slow, blinking amber light.
Connect the Ethernet cable to the WAN "O" port on the Time Capsule
Click the fan shaped AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click on Time Capsule
(The screen shot below illustrates an AirPort Express instead of a Time Capsule)
As soon as you click on Time Capsule, AirPort Setup will open automatically and take a minute to analyze the network.
After a minute or so, AirPort Setup will indicate that the Time Capsule will be set up to "extend" the AirPort Extreme network.
Enter a device name that you want to use for the Time Capsule and click Next
AirPort Setup will indicate that the network is being setup to "extend using Ethernet". When you see the message of Set Up Complete, click Done.
The Time Capsule is now providing a wireless signal with the same name and password as the AirPort Extreme network, so devices will be able to move or "roam" from one area to another and stay on the same "big" wireless network.
If you want to assign a different name to the Time Capsule network, open AirPort Utility and click on the Time Capsule icon, then click Edit
Click the Wireless tab at the top of the window
Change setting for Wireless Network Name. You can keep the same password if you want, or assign new passwords for the Time Capsule network.
Click Update to save the new settings.

Western Digital TV Live plus conected to Time Capsule

My question is one of security.
My time capsule WIFI is secured with a password, does that mean that my WD TV that is connected with a Ethernet cable to my time capsule also secure ?

There's no security over your local "wired" network, but there is a firewall between your local network and the internet that will prevent any connections to your network unless you specifically allow it.
Here I am assuming that you have your Time Capsule connected directly to a modem. If you have the Time Capsule connected to another router, then it is up to that router to provide the protection between your local network and the internet.

Slow internet conection from time capsule

I got the Time Capsule to replace my Trendnet TEW-633gr router and use as back-up slash storage. I also just bought a Macbook Pro but have not received it yet. I also just replaced my cable modem with the Motorola SB6121 becuase my speed had dropped of severely for weeks and couldnt just sit around and wait for repair service to arrive. The new modem fixed my problem when connected to the Trendnet. So I start the process for getting the Time Cap up and running which was anything but smooth. Im new to Apple products(minus the iphone) so I could bare some of the blame, but with that said....I have built my last few computers so I have a decent working knowledge. I am also really excited about the new mac comming but I need to rant a little about my first experience with owning an apple product.
First off, the instructions leave much to the imagination and they seemed little scatter brained(kinda like me atm.) I download Airport Utilty and it finds my TC. I hit continue. It searches and such then an error code. Repeated this a few times with error code(s) again. I finally get it up and running after a little prodding. YAY! exited for...slow interent again. Needless to say sad/frustrated. Hooked up the old trendnet and everything is fine.
My questions are these...
Is there some sort of compatibility issue between my TC and modem/PC's?
Can I just use the Storage on the TC via my old router via ehternet cable?
When I get my mac should the setup go smoothly?
Really any suggestions/tips on using the TC only or TC/router is what Im after.
Thanks

If the router is off on the 2wire..
the router function on my 2WIRE Modem is already turned off.
then the TC has to be in router mode and you must use pppoe authentication. otherwise you are really double NATting which could cause issues. You stated in line 3 your TC is bridged.
set to bridge on time capsule.
Is the 2wire a wireless modem router? If so the wireless could interfere with the TC.
Connect using the 2wire in router mode. and the TC in bridge.
If the 2wire is wireless, turn wireless off in the TC. Do you get better speeds now?
If you run two wireless routers next to each other you might need to fix and lock channels. There are only 3 non-overlapping channels at 2.4ghz.. 1, 6, 11.. pick one for the TC and pick another for the 2wire. The MBP is perhaps using 5ghz.. but the iphone is stuck using 2.4ghz. So you need to fix this up.
Tell us more.

My Airport Time Capsule only works when I turn off and turn on, but I think this may end up with the unit. What can this happening and how to solve?

Time Capsule Airport
Hello to all, good day, sorry my english google, but it is the tool I have at the moment. I'm having trouble with my Time Capsule Airport, I made all the settings according to the manual, but there has been a connection problem with my iMac. When I finish my work I turn off the imac and then again when they return to work and care, it can not connect to Time Capsule Airport, making it impossible to remove the files and make back up by Time Machine only works when I turn off and turn on the Airport Time Capsule , but I think this may end up with the unit. What can this happening and how to solve? Thank you.
Olá a todos, bom dia, desculpe meu inglês google, mas é a ferramenta que tenho no momento. Estou tendo dificuldades com a minha Airport Time Capsule, fiz todas as configurações de acordo com o manual, mas tem existido um problema de conexão com meu iMac. Quando termino meus trabalhos desligo o imac e depois quando retorno pra trabalhar novamente e ligo, ele não se conecta a Airport Time Capsule, impossibilitando retirar os arquivos e fazer o back-up pelo Time Machine, só funciona quando desligo e ligo a Airport Time Capsule, mas acho que isso pode acabar com o aparelho. O que pode esta acontecendo e como resolver? Obrigado.

This is easier to do with pictures perhaps.. since we do not share a common language and machine translation leaves a lot to be desired.
In the airport utility bring up your Time Capsule.
Simply post the screenshots here.
So here is mine.
Click on the Edit button and give us the Internet and Wireless and Network tab..
eg.
Please also make sure you are set to ipv6 in your wireless or ethernet .. whichever is used.. and do tell which.
This is wifi in your computer.
The following are important..
DO not use long names with spaces and non-alphanumeric names.
Use short names, no spaces and pure alphanumeric.
eg TC name. TCgen5
Wireless name TCwifi
Use WPA2 Personal security with 10-20 character pure alphanumeric password.
read apple instructions to help with TM and TC.. they did finally admit it has issues in Mavericks.
OS X Mavericks: Time Machine problems
Mount the TC manually in finder.
AFP://TCgen5.local
When asked for the password .. that is the disk access password and save it in the keychain.
Reset Time Machine
See A4 here. http://pondini.org/TM/Troubleshooting.html

How do I set up my time capsule as an internal only network.

I currently have a time capsule that was attached via ethernet cable to my wireless router (Brighthouse network) and worked fine with Time Machine.
I want to disconect it from the router (no connection via ethernet cable or wireless) and configure it to be a separate network I can connet to and use to access the Time Capsule hard drive. So I want to establish a wirless base station that creates a new internal only network, not connected to the internet, that gives me access to the hard drive using Time Capsule.
I recognize that when I connet to the Timne Capsule in this configuration I would have to select it and would not be conected to the other wireless network at my house or to the internet.
Thanks for the help

Just take the TC and reset to factory..
Setup again with no WAN connection.. but leave the TC in router mode.. it will kick up a bunch of errors about having no WAN connection.. just ignore them all.
Create a wireless network.. try and use an IP address range not used by your main network.. just to help stop confusion.
When you swap between the two it should be able to work fine.

HELP!!! remote desktop and time capsule

Hello!
Could You help me? I have two problems with access to my Time Capsule.
I have wireless network at home based on Time Capsule, with one static IP. I have conected it (wireless) with two iMac's. Me and my girlfriend we have also two macbooks and when we are out of home we want to acces data on our Time Capsule disk. I need access to disk to edit data on it while being long way out of home. Second problem is to access data on our iMac's. I bought Apple Remote Desktop software, it's incredible what it can do . But only when I'm connected to my wireless network LAN. I need to controll my iMac while being out of home. How to configure Time Capsule and ARD to acces disk and control iMac's? Let me remind You that I have one static IP for Time Capsule router WAN. Please help and I would be very very thankful for screenshots of configuraion, I'm newbie in this.
Thank You very much.
Kind regards.
Adam Milwiw-Baron

The subject of connecting via ARD over the internet has been covered many times on these forums, and info on which ports to forward on your router are in the ARD user guide.
See this article: http://www.starklmc.com/ard It should get you started, but you'll need to consult the documentation that came with your Time Capsule on setting up port forwarding correctly.

Time Capsule and Extreme Wireless network BROKEN !!!! PLEASE HELP

Hello All,
Anyones help on this would be greatly appreciated I am actually starting to loose sleep over this issue.
I have a Mac Mini Server (MM) running Lion (it's a storage thing), 1st Generation Time Capsule (TC) and a Airport Extreme (APX) the first one of the square TC looking one).
So due to living with friends I created my own little network, the MM is upstairs in my room with an ethernet connection to my TC for a quick backup and then downstairs the APX is plugged into the router (Sky Broadband), created myself a little network everyone was happy.
I had to move out for a few months took all the apple gear to the new house plugged everything PING!!!! there is my network, not had to do anyhting make any changes or anything the only thing different was the APX was plugged into a Virgin Media router.
So I moved back after a few months to the place mentioned in paragraph 3 and it has all gone belly up in a mojor way. The network I had originally built is no longer visible, I could not find the devices in the Airport Utility bad times all round. I did a soft reset on the TC and a soft reset on the APX nothing! I did a hard reset on the APX and a hard reset on the TC nothing!
I have used an ethernet connection between the TC and the APX and can pick up both of the devices (happy days you think), go through the montions in Airport Utility setup the devices and a new wireless netwrok whihc is then exteneded, then unplug the ethernet cable BOOM the devices are nolonger seen in Airport Utility.
The interesting thing is I can still the the network created on the TC and the APX on the mac, iPad and iPhone but when I try and connect to the network (whihc has full signal stregnth) I either get a conection time out error or a unable to connect tot he netowkr error.
Please, Please, Please can somone help, I am not aware of any major updates, damage, droppage of kit or anything.
Kind Regards,
Ray

The bottom line here is that it is always a good idea to reset your routers back to factory default settings and re-configure the network again when you make a change in location or in Internet service providers.
That's the best advice that I can offer for your current issues.
True, you could go with a "try this, try that" approach and possibly get things working that way. but this will likely take a lot more time and produce more headaches than simply starting over again.
Of course it is possible that you may receive other advice that tells you exactly what to do in a few simple steps...,so depending on your schedule to get the network back up and running, you may wish to wait for other suggestions.

Time Capsule with Windows Vista

I have a MacBook and a Macmini that I have conected to my Time Capsule. It works perfect.
Now I also want the Time Capsule to work with my PC (windows vista).
I can connect the PC so I have internet wireless but I can not access the hard drive in the Time Capsule.
Can anyone help me?

Click here for information.
(50292)

Problem with Time Capsule Wireless Network...

I have Time Capsule over a year and it worked fine with Xfinity Modem. Recently, Xfinity had upgraded modems to Wireless router and I have ARRIS TG862 from them. I was able to set up wireless network using bridge mode on my Time Capsule and it all worked fine for a while.
My set up is: Arris Router is conected to Time Capsule thru ethernet connection. I have two more Airport Express in different areas of the house (one in Theater room and one in upstair office). I have conncted one port of Time Capsule to linksys switch which is supplying connection for all wired devices on network.
Last week, our wirless network stopped working and I rebooted router and TC. Still no resolution. I went ahead and set up the TC to factory settings but forgot to plug out all the network connections from it. I reconfiugred Apple TC with same wireless network name and same network settings. Most of the wired devices are connecting fine and two of the iphones and Macbook Pro won't connect. iphones, seems to be getting IP address but won't connect to interent. My windows laptop says connected to "EAGLE" my wireless network but "EAGLE 2" provides internet connection. I have reset my TC to factory defaults and reset same way so many times but still same results. I called Comcast and asked them to turn off wireless in their router thinking that router is creating a second wireless network but I still have the same issue.
Any suggestions on how should I set up my TC? I think, it went insane..............:(
Should I set up TC with a brand New wireless network Name to resolve this issue?
I have 7.6.4 version on TC.
I thought I knew, but what's the right procedure to set up TC? Plugged in the router and unplug from everything else and connected thru an ethernet connection to my laptop?
I have wasted so much time on this with the same results every time.
I did unplug all the network connections from TC and reset to factory defualts and set up my wireless again but same results.
Can someone please help me with this? Thanks in advance.

What is the model of the TC? The actual number.. A1xxx from the base of the TC is important.
When you have a modem router.. then the TC must be in bridge mode.. and create a wireless network.
Your names are not yet windows compatible.. please use all names that are short, no spaces and pure alphanumeric.
Fixing names is important part of this.
But the latest firmware 7.6.4 is also troublesome. I would downgrade it to 7.6.1 and factory reset before you start that process.
Any TC older than 3years may have hardware issues.. a Gen3, A1355 may need a replacement and certainly anything older does.
Drivers in windows for wireless are problematic as well..
Certainly start there and see how it goes.

Fail to print via time capsule (samsung scx-4200)

Hi, i have trouble with print issue..
I have 2 mac os devices:
mac pro with 10.6.7 - conected via ethernet to time capsule
and macbook air with 10.6.7 - conected via wifi to time capsule
and one non mac (acer notebook with ubuntu linux) conected via wifi to time capsule
I buy new printer Samsung SCX-4200 and connect it to time capsule - try to print from Mac Pro - its easy started and good worked..
try to add printer to ubuntu - all nice, printer found, test page work good..
and go to macbook air and try to add printer. Printer adds normally but when i try to print i receive 'nothing' and printer Paused.. But when i put scx-4200 directly to my macbook air via usb - it print and scan normally without any problems.
In both variants with mac os i install drivers for print for mac from samsung.com site directly.
Please help to resolve this issue, no possible to insert usb to macbookair any time when i need to print something.
in /var/log/cups/* i have next messages by tail -f /var/log/cups/* and open textedit and type some text + CTRL+P end press enter ->
localhost - - [30/May/2011:20:37:12 +0300] "POST /printers/Samsung-4200 HTTP/1.1" 200 1312 Create-Job successful-ok
localhost - - [30/May/2011:20:37:12 +0300] "POST /printers/Samsung-4200 HTTP/1.1" 200 12353 Send-Document successful-ok
localhost - - [30/May/2011:20:37:12 +0300] "POST / HTTP/1.1" 200 310 Set-Job-Attributes successful-ok
==> page_log <==
Samsung-4200 9 l33t [30/May/2011:20:37:12 +0300] 1 1 - localhost Untitled A4 -
==> error_log <==
E [30/May/2011:20:37:12 +0300] [Job 9] Unable to read response header - short read
E [30/May/2011:20:37:12 +0300] [Job 9] Unable to open printer (read failure)!
D [30/May/2011:20:37:12 +0300] [Job 9] The following messages were recorded from 20:37:12 to 20:37:12
D [30/May/2011:20:37:12 +0300] [Job 9] Adding start banner page "none".
D [30/May/2011:20:37:12 +0300] [Job 9] Queued on "Samsung-4200" by "l33t".
D [30/May/2011:20:37:12 +0300] [Job 9] File of type application/pdf queued by "l33t".
D [30/May/2011:20:37:12 +0300] [Job 9] Setting job-hold-until to no-hold
D [30/May/2011:20:37:12 +0300] [Job 9] Adding end banner page "none".
D [30/May/2011:20:37:12 +0300] [Job 9] Job released by user.
D [30/May/2011:20:37:12 +0300] [Job 9] job-sheets=none,none
D [30/May/2011:20:37:12 +0300] [Job 9] argv[0]="Samsung-4200"
D [30/May/2011:20:37:12 +0300] [Job 9] argv[1]="9"
D [30/May/2011:20:37:12 +0300] [Job 9] argv[2]="l33t"
D [30/May/2011:20:37:12 +0300] [Job 9] argv[3]="Untitled"
D [30/May/2011:20:37:12 +0300] [Job 9] argv[4]="1"
D [30/May/2011:20:37:12 +0300] [Job 9] argv[5]="AP_ColorMatchingMode=AP_ApplicationColorMatching AP_D_InputSlot= nocollate com.apple.print.DocumentTicket.PMSpoolFormat=application/pdf com.apple.print.JobInfo.PMApplicationName=TextEdit com.apple.print.JobInfo.PMJobName=Untitled com.apple.print.JobInfo.PMJobOwner=l33t com.apple.print.PageToPaperMappingMediaName=A4 com.apple.print.PageToPaperMappingType..n.=1 com.apple.print.PrinterInfo.PMColorDeviceID..n.=5462 com.apple.print.PrintSettings.PMColorSpaceModel..n.=1 com.apple.print.PrintSettings.PMColorSyncProfileID..n.=1580 com.apple.print.PrintSettings.PMCopies..n.=1 com.apple.print.PrintSettings.PMCopyCollate..b. com.apple.print.PrintSettings.PMDestinationType..n.=1 com.apple.print.PrintSettings.PMFirstPage..n.=1 com.apple.print.PrintSettings.PMLastPage..n.=2147483647 com.apple.print.PrintSettings.PMPageRange..a.0..n.=1 com.apple.print.PrintSettings.PMPageRange..a.1..n.=2147483647 DestinationPrinterID=Samsung-4200 media=A4 PaperInfoIsSuggested..b. pserrorhandler-requested=standard job-uuid=urn:uuid:6c043468-8143-3740-4f5f-c1b8f2958f3b job-originating-host-name=localhost time-at-creation=1306777032 time-at-processing=1306777032 job-impressions=1 com.apple.print.PrintSettings.PMTotalSidesImaged..n.=1 com.apple.print.PrintSettings.PMTotalBeginPages..n.=1 PageSize=A4"
D [30/May/2011:20:37:12 +0300] [Job 9] argv[6]="/private/var/spool/cups/d00009-001"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[0]="<CFProcessPath>"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[1]="CUPS_CACHEDIR=/private/var/spool/cups/cache"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[2]="CUPS_DATADIR=/usr/share/cups"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[3]="CUPS_DOCROOT=/usr/share/doc/cups"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[4]="CUPS_FONTPATH=/usr/share/cups/fonts"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[5]="CUPS_REQUESTROOT=/private/var/spool/cups"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[6]="CUPS_SERVERBIN=/usr/libexec/cups"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[7]="CUPS_SERVERROOT=/private/etc/cups"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[8]="CUPS_STATEDIR=/private/etc/cups"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[9]="HOME=/private/var/spool/cups/tmp"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[10]="PATH=/usr/libexec/cups/filter:/usr/bin:/usr/sbin:/bin:/usr/bin"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[11]="[email protected]"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[12]="SOFTWARE=CUPS/1.4.6"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[13]="TMPDIR=/private/var/spool/cups/tmp"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[14]="USER=root"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[15]="CUPS_SERVER=/private/var/run/cupsd"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[16]="CUPS_ENCRYPTION=IfRequested"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[17]="IPP_PORT=631"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[18]="CHARSET=utf-8"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[19]="LANG=en_US.UTF-8"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[20]="APPLE_LANGUAGE=en-US"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[21]="PPD=/private/etc/cups/ppd/Samsung-4200.ppd"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[22]="RIP_MAX_CACHE=8m"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[23]="CONTENT_TYPE=application/pdf"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[24]="DEVICE_URI=dnssd://Samsung%20SCX-4200%20Series._riousbprint._tcp.loca l."
D [30/May/2011:20:37:12 +0300] [Job 9] envp[25]="PRINTER_INFO=Samsung-scx4200"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[26]="PRINTER_LOCATION=printer123"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[27]="PRINTER=Samsung-4200"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[28]="CUPS_FILETYPE=document"
D [30/May/2011:20:37:12 +0300] [Job 9] envp[29]="FINAL_CONTENT_TYPE=printer/Samsung-4200"
D [30/May/2011:20:37:12 +0300] [Job 9] Started filter /usr/libexec/cups/filter/cgpdftoraster (PID 1759)
D [30/May/2011:20:37:12 +0300] [Job 9] Started filter /Library/Printers/Samsung/SCX-4200/rastertosec (PID 1760)
D [30/May/2011:20:37:12 +0300] [Job 9] Started backend /usr/libexec/cups/backend/dnssd (PID 1761)
D [30/May/2011:20:37:12 +0300] [Job 9] Resolving "Samsung SCX-4200 Series._riousbprint._tcp.local."...
D [30/May/2011:20:37:12 +0300] [Job 9] STATE: +connecting-to-device
D [30/May/2011:20:37:12 +0300] [Job 9] Resolving "Samsung SCX-4200 Series", regtype="_riousbprint._tcp", domain="local."...
D [30/May/2011:20:37:12 +0300] [Job 9] Looking for printer...
D [30/May/2011:20:37:12 +0300] [Job 9] `/private/var/spool/cups/d00009-001' has 1 pages.
D [30/May/2011:20:37:12 +0300] [Job 9] cgpdftoraster - opened PPD file "/private/etc/cups/ppd/Samsung-4200.ppd"...
D [30/May/2011:20:37:12 +0300] [Job 9] cgpdftoraster: size->width = 595, size->length = 842, size->top = 829.5, size->bottom = 12.5, size->left = 12.5, size->right = 582.5
D [30/May/2011:20:37:12 +0300] [Job 9] cgpdftoraster: PreferredRotation = -90
D [30/May/2011:20:37:12 +0300] [Job 9] cgpdftoraster - languageLevel = 3, mediaBox.size.width = 595, mediaBox.size.height = 842
D [30/May/2011:20:37:12 +0300] [Job 9] skipBytesPerRow = 2
D [30/May/2011:20:37:12 +0300] [Job 9] band width = 4750, bytesPerRow = 4752, band height = 2206, height = 6808
D [30/May/2011:20:37:12 +0300] [Job 9] context width = 4750, height = 2206, bitsPerComponent = 8, bitsPerPixel = 8, bytesPerRow = 4752, bitmapInfo = 0, resolution = (600.000000, 600.000000)
D [30/May/2011:20:37:12 +0300] [Job 9] NOT using display list
D [30/May/2011:20:37:12 +0300] [Job 9] PAGE: 1 1
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 0% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 7% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 14% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 22% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 29% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 36% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 44% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 51% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 58% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 66% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 73% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 80% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 88% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] Printing page 1, 95% complete...
D [30/May/2011:20:37:12 +0300] [Job 9] cgpdftoraster: bytes written for sheet 1 = 32338000
D [30/May/2011:20:37:12 +0300] [Job 9] Ready to print.
D [30/May/2011:20:37:12 +0300] [Job 9] Resolved as "riousbprint://Time-Capsule-d99f2b.local.:10000/Samsung%20SCX-4200%20Series%208 T66BACPB13615P."...
D [30/May/2011:20:37:12 +0300] [Job 9] STATE: -connecting-to-device,offline-report
D [30/May/2011:20:37:12 +0300] [Job 9] Executing backend "/usr/libexec/cups/backend/riousbprint"...
D [30/May/2011:20:37:12 +0300] [Job 9] STATE: +connecting-to-device
D [30/May/2011:20:37:12 +0300] [Job 9] Looking up "Time-Capsule-d99f2b.local."...
D [30/May/2011:20:37:12 +0300] [Job 9] Connecting to Time-Capsule-d99f2b.local.:10000
D [30/May/2011:20:37:12 +0300] [Job 9] Connecting to printer...
D [30/May/2011:20:37:12 +0300] [Job 9] Connected to 0.0.0.6:10000 (IPv4)...
D [30/May/2011:20:37:12 +0300] [Job 9] Set job-printer-state-message to "Unable to read response header - short read", current level=ERROR
D [30/May/2011:20:37:12 +0300] [Job 9] Backend returned status 1 (failed)
D [30/May/2011:20:37:12 +0300] [Job 9] Printer stopped due to backend errors; please consult the error_log file for details.
D [30/May/2011:20:37:12 +0300] [Job 9] End of messages
D [30/May/2011:20:37:12 +0300] [Job 9] printer-state=5(stopped)
D [30/May/2011:20:37:12 +0300] [Job 9] printer-state-message="Unable to open printer (read failure)!"
D [30/May/2011:20:37:12 +0300] [Job 9] printer-state-reasons=paused

Do a google around for that printer and airport usb.. (since airport is more common).
eg. https://discussions.apple.com/thread/1785847?start=0&tstart=0
Not all printers work or work well through usb print server.. often the drivers are just not written for remote usb connection. Or the printer is GDI type and actually needs direct connection to process the job.
Proper network inkjet printers are cheap.. keep the Canon connected to a computer if you want.. and get a wireless or ethernet network printer.. do not use the USB.. use the printers own internal print server.. and these days make sure it does airprint if you want to use iOS devices.
Remember the printer is cheap.. the companies make all their money on blades ink cartridges. Which they now add chips to, to prevent you cheating and buying OEM types.

Time capsule wil not alow iphone to connect by wifi.

My iphone can not go WIFI from my time capsul. When i try to connect i gett the message "could not conect to my network"
How do i fix it?
Johnny

Set the 2.4ghz network to a new name.. I suggest TC24ghz. (name should be short, no spaces and pure alphanumeric).
Test the channels, 1, 6, 11 in reverse order.. ie 11 is usually the free one.
Test with WPA2 Personal security and a short pure alphanumeric password say 10 characters.
No luck remove the security and try it.
No luck take the TC back to Apple for testing. Take your phone with you. Ask apple to setup the two.

Time capsul on cabel net and wifi net

Can I connect Time capsul on the cabel net and wifi net at the same time. I have 2 PCs connected in cable net and macbook is conected via wifi. I have some problems with this, pls help.
Thanks

Not quite sure what you're asking -- what wifi is the macbook connected to?
You can set the time capsule up to connect to the cable network and create a wifi network in your house/apartment that will let your macbook connect to the cable network.
Or, if by "wifi" you mean a public wifi network, you can set up the time capsule to be a repeater for that within the house/apartment, although that's probably not the best way to go.
You cannot connect the time capsule to both simultaneously, however--it needs to have one source of connection to the internet.

é possível conectar internet via usb no time capsule?

tenho um modem usb da prestadora oi, quero conecta-lo no meu time capsule, mas nao estou conseguindo, alguem sabe de alguma dica?

This may be a printer driver issue. I recommended first connect printer directly to computer and check for Software Updates, this will tell you if you have any printer updates.
If you are using a Mac computer follow troubleshooting steps in HT3500
(Basically, navigate to Print & Scan in System Preferences and right-click or control-click on printer from left and choose Reset Printing System, then re-add preferred printer.)
If you are using a Windows computer download and install Bonjour Print Services DL999

Time Capsule conection

Similar Messages

Maybe you are looking for