Time capsule connect to existing network cannot connect MBP via ethernet

I have set up my time capsule via Airport utility to "connect to existing network", which is my Netcomm wireless router (which is my DHCP server). MBP connects perfectly to time capsule if wireless is on, presumably via the Netcomm. But if I plug the MBP into an ethernet port on the time capsule it is not recognized and it gets a self assigned ip 169.254.x.y.
Airport utility is very restrictive in the options and is basically useless in resolving the obvious ip conflict. Is there any trick to getting both the wireless and ethernet to work ? It should not be this difficult....
The time capsule 2T disk is useless as a backup device over wireless.

[email protected] wrote:
I have set up my time capsule via Airport utility to "connect to existing network"
Is that the exact wording of the option you chose? In AirPort Utility I see options of "Create a wireless network", "Join a wireless network", and "Extend a wireless network". (Perhaps the difference is due to language usage.) The option to "Join a Wireless Network" is only useful for sharing disks and printers. It doesn't support Ethernet ports.
if I plug the MBP into an ethernet port on the time capsule it is not recognized
With some options there's a checkbox to "Allow Ethernet Clients". If you see that, try it.

Similar Messages

HT1178 I would like to update to time capsule. My existing extreme is connected to 4 express around the house. If I install capsule, do I have to reset all express machines or will it work automatically?

I would like to update to time capsule. My existing airport extreme is connected to 4 airport express around the house. If I install capsule, do I have to reset all express machines or will it work automatically?
Thanks!

You need to start over.. the MAC addresses are different.. if you try it will fail.. even with the same names and same IP addresses because it is not the same box.. it is much better to start over.
And even use a wholly different naming structure.. short.. 2-20 characters no spaces.. and pure alphanumerics.
It doesn't take long really to redo it.

Airport Time Capsule : extension to existing network

My new Airport Time Capsule just want to create its own network, but I want it to extend my existing network. When I pick "other options" and "add to an existing network" nothing happens??

Not if you want to connect the Time Capsule using wireless. It must connect using a permanent wired Ethernet connection.
The Time Capsule would only extend/work using wireless if you had another Apple router....Not a BT router.

If I add time capsule to my existing network will I be using the time capsules dualband network?

I already have a wireless network, and I want to be able to use time capsule for backups and it's dualband network. Would I be able to just add to existing network to get both of those features or would I have to create a whole new wireless network. Just to clarify on the setup, would I plug the time capsule into my router that's connected to the modem?
Sorry I'm very new at this.
Thank you,
Ferg

The Time Capsule is a router / hard drive only. It does not have a built in modem.
If your current "router" is really a gateway (combination modem / router on the same chassis), you will need to plug the Time Capsule into one of the ethernet ports on your "router" and configure the Time Capsule to "create a wireless network".
It's very important that you configure the Time Capsule in "Bridge Mode", if you connect it to your current router.
If on the other hand, you have a separate modem now and your router is connected to the modem, you could simply replace the old router with the Time Capsule.
Post back if you need more info.

How do I connect my Time Capsule to an Existing Network?

I've seen a few similar discussion threads and seem to suggest I can't do this without an Apple Router, but I just want to clarify:
I have a 3TB Time Capsule, I want to connect it to my existing Wireless Network so that I can set it up with Time Machine.
I have connected it to my current router (which is AT&T, not Apple) via an ethernet cable that's plugged in to a LAN port on the router, and the WAN port on the TC (I also tried this in a LAN port on TC but it didn't seem to make a difference).
I was able to find my TC on Airport Utlility, but when I try to select the Join Existing Network option it just keeps bringing me back to the Create New Network screen.
How do I fix this? Does it really need to be an Apple router? Am I just plugging the ethernet into the wrong port? Or should I just continue in the Create New Network screen and enter the same name and password as my existing network, or would that create a duplicate network?
Honestly I don't really care about extending the network or not, I just want to be able to wirelessly access the Time Capsule to use it with Time Machine.

unless i'm missing something, i think you got mixed up, this is easy google for walk throughs
i'm assuming this is the new 3tb tc AC or 'tower' shape, if so, its wifi will run circles around your at&t device
unplug the at&t box for a minute and plug it back in
factory reset your tc - unplug it, hold down reset and keep holding while you plug it back in - only release reset when amber light flashes in 10-20s
connect the tc to your at&t box via eth in the wan port, wait 1 minute, open airport utility look in 'other wifi devices' to setup the tc
create a new wifi network (give it a different name than your at&t one) and put the tc in bridge mode (it may do this automatically for you, but you should double check) under the 'network' tab
login to your at&t router and disable wifi on it
add new clients to the new wifi network, and point your Macs to the time machine for backups

Time Capsule & Airport Express Extended Network loses connection!

OK, so I am an Apple virgin of 2 months experience, after many many years with Windows based PCs, so please be patient and gentle with me. Sorry about the long explanation.....
My set-up comprises of a Time Capsule, which is connected to the Internet via a NetGear ASDL modem. Both pieces of equipment are situated in my wife's office on the first floor of our house. My office is on the ground floor, where I have a 27" iMac and an Airport Express which is connected to a printer via the USB port. The Airport Express is sited about 10 feet from the iMac.
All software and firmware are lastest versions - TC v7.5, AX v7.4.2 & Airport Utility v5.5.
For the past 2 months, I have only been using the AX to print wirelessly and the set-up has worked faultlessly.
Earlier this week, I decided change the configuration to extend the network to allow me to use my laptop & iPhone in areas of the ground floor where I had no signal. I followed the online instructions and first changed the TC to check the box to 'allow this network to be extended', after updating the configuration successfully I moved to the AX. Here I changed the wireless mode to 'Extend a wireless network', selected the network name and checked the 'Allow wireless clients' box. This also updated successfully.
Everything ran correctly and the range of the network was greatly increased.......great, job done...not!
After about 3 hours the iMac lost the connection and the TC disappeared from the Airport Utility pane and refused to reappear. I checked but also couldn't connect or see any network on the laptop or iPhone, so have dismissed a fault with the iMac. I finally got things back up after doing a power reset of the TC, but after a few hours same problem occurred, and occurred and occurred. By clicking the Airport Utility icon on the top right of the screen and following the prompts from 'no Internet connection', I can at least get things up and working without a power reset of the TC, but the connection still drops after 2-5 hours each time.
My first call to Apple Support led to a full reset and re-config of both the TC and AX, setting the extended network up as I had done originally. The only difference was an iMac reset (alt/cmd P&R on power up) and changing the 2.4Ghz channel from 1 to 11. This had no affect and the connection drop-out problem continued.
My second call to Apple Support led to me being passed to a Level 2 Techie, who first suggested that I tried disabling the Guest Network - tried it, and it made no difference. I was then told to try a WDS network, which whilst not losing connection, is slower and has less range than the original extended network and frankly sounds a cop-out.
Has anyone had a similar problem, anyone solved the problems, can anyone offer any help or advice please.. I'd appreciate any input....thanks.

Similar problem here. Cable Modem (Moto SB6120)->AEBS (802.11n dual-band)>AX (802.11n) for wireless connection to MacBook Pro running Mac OS X 10.6.2. AEBS configured as dual-band: 801.11a/n at 5GHZ and 801.11b/g/n at 2.4 GHZ. AX configured to wirelessly extend the AEBS 5GHz 802.11a/n network. I am able to run on the extended 5GHz network (via AX) for varying lengths of time, until the internet connection dies. When this occurs, I am able to switch over to the 2.4GHz network to get back online. Solution up until now has been to unplug the AX, then plug it back in. After the AX restarts, I am able to hop back onto its 5GHz signal and get to the internet. However, the internet connection on this band will drop again after some time.
I was on the phone with Apple Support twice in the past week to get this resolved, but no joy. Senior Advisor seemed to think that my AX was working properly, and that that the problem could be with my AEBS -- perhaps the 5GHz antenna might be bad in my AEBS? Seems odd to me, since both my AEBS and AX are less than 2 months old...
I just read the post from LocoDoc and decided to see if I could replicate the problem. Sure enough, when I am connected to the internet via my AX extended 5GHz network signal and a Time Machine backup starts, the internet connection quits. Only recourse is to restart the AX. Note that I do not experience this problem with Time Machine while connected wirelessly straight to the AEBS 5GHz signal. Only when I am connected to the "extended" signal via the AX.

"added time cap to existing network" and can't get Ethernet cable connection to Time cap to work...

I added a new time capsule to my existing wifi network. Everything initialized well and time machine could see the TC. I tried to connect a cable directly to the TC for the first backup... But the cable connection doesn't see the TC. Ideas?

If you used join a network then the TC turns off its ethernet ports.

Connecting the time capsule to a wireless network (university)

I just purchased my first mac computer, and the time capsule. I am a university student, and my housing has wireless network, so i would need to configure it to that network (which requires registration). When I first opened everything up, I could see the time capsule in the airport utility, but now I cannot. I dont really know where to go from here, because all of the manuals go from being able to detect the time capsule. On top of that how do I connect the wireless to the registration required network? Any help is much appreciated.

how can I use the time capsule as a "wifi acceptor" to connect with my wireless network, and then boardcasting wifi signal to my devices?
Unfortunately, this is not possible.
In order to broadcast a wireless network with Internet access, the Time Capsule must be provided with a wired Ethernet connection at its WAN "O" port.
Check wtih your Internet Service Provider to see if they have an adapter or other device that will provide a wired Ethernet connection to the Time Capsule.

I am using SURPLUSMETER :) I am also using Apple Airport Time Capsule as my Router that is connected to my Satellite dish Internet Modem ... Now on the Surplusmeter I have the option for PPP Modem . Ethernet Port , Airport , Network Card ,

I am using SURPLUSMETER I am also using Apple Airport Time Capsule as my Router that is connected to my Satellite dish Internet Modem ... Now on the Surplusmeter I have the option for PPP Modem . Ethernet Port , Airport , Network Card , & Adaptor .
Which one can I use properly to monitor all the wireless Devices in my hous

Actually, none of the options will do what you are looking for it to do. That is because, this application only monitors the traffic from the device it is hosted on. That would also mean that you would have to run a copy on each computer that will access the Internet on your network; note their individual usages, and then, combine them to get an idea of the total usage.
However, if you are only interested in the amount of Wi-Fi traffic that only your computer is seeing, then the "AirPort Network Card" option would be the correct choice.

Connecting Mac Pro to Time Capsule to get wireless network!

My brother just bought for me the newest Mac Pro with MAC OS 10.6 and already have a TIme Capsule. At the Apple Store they told him that there was no need for him to buy a AirPort Extreme Wi-Fi Card, because I already have Time Capsule and through it I could connect my Mac Pro to my wireless network at home. Is this right?
The router of the internet is located at my living room and the time capsule is at my bedroom. What I'm trying to say is... Can I use the Time Capsule as a AirPort Extreme Wi-Fi Card for my Mac Pro?
I'll wait anxiously for an answer.

You seem a little confused. The Mac Pro must have a wireless card installed inside and connected properly. Then you can wirelessly connect to that Time Capsule.
If you do not have the card installed inside that Mac Pro then figure a way to run fast cat ethernet cable to the Time Capsule.

About connecting my time capsule to a wireless network

I have bought a time capsule but as my place isn't ethernet-able, how can I use the time capsule as a "wifi acceptor" to connect with my wireless network, and then boardcasting wifi signal to my devices? I have tried the extending a network option, after it restarted and I can't even search any base stations. Can anyone suggest me a solution to that? I really need to do so although I know that this isn't a purpose of using the timecapsule. In other words I'm trying to make the time capsule as a wireless modem to connect to another wireless network, in the mean time boardcasting wifi signal to my devices.
Thanks guys.

how can I use the time capsule as a "wifi acceptor" to connect with my wireless network, and then boardcasting wifi signal to my devices?
Unfortunately, this is not possible.
In order to broadcast a wireless network with Internet access, the Time Capsule must be provided with a wired Ethernet connection at its WAN "O" port.
Check wtih your Internet Service Provider to see if they have an adapter or other device that will provide a wired Ethernet connection to the Time Capsule.

Can time capsule boost the wireless network without beeing connected with cabel, hence wirelessly?

Can time capsule boost the wireless network without beeing connected with cabel, hence wirelessly?

Yes, providing that the wireless network has been created by another Apple "n" router.
The "extend a wireless network" feature on the Time Capsule is not compatible with devices from other manufacturers.

HT201945 How do I use my time capsule on an existing WIFI network?

How do I use my Time Capsule on an existing WIFI network?

Use an Ethernet cable to connect from one of the LAN <--> ports on your existing wireless router to the WAN "O" port on the Time Capsule and then use the setup "wizard" on your Mac to configure the Time Capsule.
It will suggest that you set up the Time Capsule to create a new wireless network. If you don't want or need another wireless network, you can turn off the wireless function of the Time Capsule and use it as wired hard drive only.
Leave the Ethernet cable connected at all times. If you need to locate the Time Capsule in a different area, you can put it anywhere that the Ethernet cable will reach up to about 330 feet or 100 meters.
The only exception to using an Ethernet cable would be if your existing wireless network is provided by another Apple router. Then.....you would have the option to have the Time Capsule connect using wireless and extend the network, although using a wired connection would still be the better way to go in terms of performance.

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network?

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network? I have an ISP provided wireless Router that has to remain as the base station. I am able to join my 1/2TB Airport Extreme and Airport Express to the network, but I can't access/use Time Machine.

One option would be to connect the Time Capsule (TC) to the ISP-provided wireless router by Ethernet. You can then configure the for a roaming network. Then, depending on what your goal is for the AirPort Express, you can either: 1) Add it to roaming network, 2) Configure the TC & the Express for an "extended" network, or 3) Configure the Express to "join" the roaming network for AirPlay.

Time Capsule to join existing wireless network

Hi All,
I have a question, as despite experimenting and reading all I can find on the subject I am no closer to a definite answer.
I have the old 500gb Time Capsule (802.11n non-simultanious version).
I presently have a BT HomeHub 2.0 as my wifi router downstairs, and use a Linksys WRT54GS to connect to the network SSID provided by the HomeHub. All my desktop machines, etc are then connected into the 10/100 switch in the WRT54GS, giving them access to the WiFi network.
Ideally I wanted to replace the WRT54GS with my Time Capsule, so that my desktop machines upstairs plug into the 10/100/1000 ethernet ports on the Time Capsule, which is then in-turn connected wirelessly to the BT HomeHub downstairs for Internet access. (The benefit of this being increased speed thanks to the 802.11n technology in the HomeHub and Time Capsule).
Sadly, the Time Capsule does not seem to like connecting to the HomeHub's SSID, each time giving me the flashing amber light. Normally, I would simply re-configure the network so the BT HomeHub connects to an SSID provided by the Time Capsule, but my version of the HomeHub is not capable of doing this, or using a WDS type setup.
WiFi signal strength is good where the Time Capsule is located, the network is using WPA/WPA2 mixed authentication, and other devices can connect to the SSID.
Any help on this is much appreciated,
Thanks,
Jon

Welcome to the discussions!
When the Time Capsule "joins" a wireless network, (which is the only way that it could connect to the HomeHub network unless you use ethernet) the ethernet ports on the device are not active. When you configure the TC to "join", it really takes on the function of a wireless backup device, nothing more.
The Time Capsule cannot be configured for a WDS type arrangement with your HomeHub because it is not compatible.
If you want to connect the Time Capsule to the HomeHub and have the Time Capsule create a wireless network, then you must use an ethernet cable from one of the LAN ports on your HomeHub to the WAN port on the Time Capsule and configure the TC to act as a "bridge".
If you are unable to run an ethernet cable, the next option would be to use ethernet powerline adapters to use the wiring in your home to transmit the ethernet signal.

Time capsule connect to existing network cannot connect MBP via ethernet

Similar Messages

Maybe you are looking for