Time capsule does not appear in shared devices

All of the sudden my Time Capsule does not show up in the shared devices. It's all up to date, it is working fine as a router and internet connection works fine. It also show up in the airpot utility and the light is green however it does not show up on the shared devices so I cannot access the data folider anymore.
Furthermore Airport utility indicates that the disk is damaged but I cannot repair it because I cannot access it.
Any ideas? (beside doing a reset which I have already done)

That is bad.. the light should not be green unless you told the TC to ignore the problem.
A damaged disk has to be replaced.. if the SMART has gone off or is showing as bad or no capacity then you need to replace the disk (or if under warranty.. the whole TC).
How old is the TC?
Model number from the base A1xxx helps.
You can try doing an erase from the airport utility if the disk shows up at all. But if SMART has gone off the disk will need replacement anyway.
If less than 1year return to apple for warranty replacement.. and if you have applecare on a computer it will cover the TC for up to 3years although the rules are strict.. so check.
See instructions for removal of the hard disk.
http://www.ifixit.com/Device/Apple_Time_Capsule_Model_A1302
Certainly if the TC is older than 3years.. it might be better to consider replacement. Certainly replacing a hard disk could be just short fix until the power supply also goes.

Similar Messages

Airport time capsule does not appear within wi-fi networks on my OSX neither on my IOS devices, even though the backup for my OSX is on progress. why it does not appear?

Airport time capsule does not appear within wi-fi networks on my OSX neither on my IOS devices, even though the backup for my OSX is on progress. why it does not appear?
Is it because the backup on progress?

Hmmm.. ok.. well you are kind of on your own.. purchasing from another country leads to problems.. especially as the TC itself is regional .. all the setup applies to the region it is sold in.
Make sure you are using ipv6 in the computers..
See
http://support.apple.com/kb/TS4597
The 6.3 utility will not work without it.
Make sure all names are short, no spaces and pure alphanumeric.
Do a full reset and start over.
But there are no more controls.. you cannot set mode..
You can set wireless channels.. so do .. try different wireless names for the different bands.. and set fixed channels.. whatever your country allows, usually 2.4ghz you can use 1, 6, 11 but 13 maybe an option as well. 5ghz is much less clear and there are more variation. Just set to one channel and then another.
Set WPA2 Personal security with a 10-20 character password .. pure alphanumeric mix of upper and lower case and numbers.

Time capsule does not appear in the finder.

My time capsule appears in airport utility. It is ready to go. I have it on ethernet because airport isn't a very powerful wireless router. The time capsule does not appear in the finder. It does not appear in the disc utility. It does not appear in time machine. The airport utility will do factory resets, get it ready for internet, whatever. The rest of my net work can not see it.
I have done the finder preferences. I have restarted the computer, jiggered the sharing preferences, done factory resets, tried to find sparce bundles and sparse bundles, reset the finder, force quit finder, tried to find finder plsts, trawled the discussion pages, tried to find server addresses and apple ids. Nothing seems to work.
Time capsule never seems to work as smoothly as it supposed to. I shudder to present my problems to apple support because I know that its a long road and will probably end in tears. But here I am, naked before this disappointing edifice.
Does anyone have any ideas?

What is the make and model number of your modem?
I have a microwave modem on my roof. I don't think that has anything to do with this. I am not using my airport for a wireless router, only as a time capsule connected by ethernet. The Airport Utility calls my airport : Airport Extreme 802.11 ( 1st Generation )
Is the Time Capsule acting as your main router or is another device handling those services?
No, I have a lyncsis router. The wireless router function on airports doesn't seem to work very well. I don't think thats a problem with mine. My brothers have gone with lyncsis as well.
Was the Time Capsule visible in the Finder before, and is now "lost", or has it never appeared in the Finder?
It appeared on my previous laptop. That died. Now I have an imac. The airport has never appeared on the imac.
Thanks for trying to help so quickly
JOhn

Time Capsule does not appear in AirPort Utility after Yosemite upgrade

Just upgraded to Yosemite and the Time Capsule appears as a shared device in Finder, but does not appear in AirPort Utility. Any solution to this so I can manage my Time Capsule again?

I'm having the same problem. Did you reset your Time Capsule to factory settings or simply restart it?

Time Capsule does not appear in iPhone 4 wifi network setting

I just set up Time Capsule on my IMac. I was able to connect to the wifi network but do not see the TC on my phone's wifi network settings. I have the Airport Utility app and I do not see my phone on the any of the Airport utility maps on the Mac or phone. I tried to set up my IPad 3 and no luck it only recognizes the wifi network and not TC.
I tried to use the demo that appears on Apple's TC info link and I do not see the same info on my phone when following the directions. I am a new IMac user my be I have a setting wrong. Please help.
http://www.apple.com/timecapsule/wireless.html

The iOS devices seem to have issues if the wireless name is AFP type..
I suggest you go back into the TC setup.. you may need to use 5.6 utility.. to get finer controls.
http://support.apple.com/kb/DL1482
Change the wireless name to short, no spaces pure alphanumeric.. I also recommend a different name for 5ghz wireless in the advanced wireless page.
Set the wireless to fixed, a/n - b/g
And then lock the wireless channel.. for 2.4ghz, set to 1, 6 or 11 in turn as the only non-overlapping channels.

My external hard drive connected to my time capsule does not appear in Finder

My Mac formatted external hdd doesn't appear in the TC folder in finder. It did once, but every time i shut down the computer or don't use it for a long time, it dissapears and only appears again if i disconnect it, connect it back again and try this 4-5 times. I do have the latest software updates on both computer and TC so that's not the problem. The hdd has it's own power supply aswell.
I know this is a somewhat common problem for airport extreme users, but so far no one has given me an answer good enough so the problem still exists.

Well, let's see...
I've updated the software on the TS
I formated the ext hdd to mac os x and then copied all my stuff back again.
I've tried to disconnect it and reconnect it.
I've tried to use the ext both WITH the power supply and WITHOUT it. In both cases the hdd starts up as I connect it to the TS, the blue light is turned on (on the hdd) and you hear the drive spinning, but it has a really hard time showing up in finder.
Whenever I connect the ext hdd to my computer it always appears, so it's clearly no problem with the hardware.
Unfortunately I don't know any one else who has a TS och Airextreme, otherwise I would've tried it on their.
Sometimes it just appears in finder as it should after some reconnecting, but I have no clue when or why.

Time Capsule crashing; not appearing in AirPort Utility

Hi all
My Time Capsule keeps on crashing, and is currently not appearing in the AirPort Utility window. I restarting it by unplugging it and plugging it back in again, but it will randomly crash again, or the sessions will be interrupted on the TC drive and the additional HDD that's plugged into it. I'm not really sure what's going on here. It's not like I'm sitting too far away from the Time Capsule (less than 3m, in fact).
The only thing that's going on that could be causing this, as far as I can see, is my attempting to migrate my files and folders from my old PowerBook to my new MacBook Pro (a procedure that is not, in all honestly, going all that well).
Thanks in advance

Rob,
If you don't mind a few more suggestions...
*_Time Capsule Weak Signal Strength / Dropped Connections_*
Forgive the size of the post, but the suggestions below have helped others with similar issues. Try each topic individually and see if things improve, If not move on to the next one.
*Keep the Time Capsule Cool*
Some posters have observed that when they positioned the Time Capsule for better ventilation and cooling, their network connectivity issues resolved themselves. Also avoid locating the devise within poorly ventilated cabinets or piling items around or on top of it.
*Time Capsule Orientation*
While the location you chose to setup your Time Capsule may be acceptable, but the direction it is oriented can have an effect on signal strength. It appears that the signal of the Time Capsule does not radiate equally from all sides of the devise.
The antennas within the devise are positioned along the 3 smooth sides. That is, there is no antenna on the side bearing the ports and cables. As a result, position the devise with the ports and cables AWAY from the direction of most of the clients that will be connecting to it.
*Cordless Phones*
Some users have discovered that the cordless phones they have in the home occupy or are near the same bandwidth as their wireless network (2.4Ghz or 5Ghz). Try temporarily disabling the handsets and their bases and see if network connectivity improves. If so you may need to change the channel that the phone uses or purchase phones that occupy a different bandwidth.
*Proximity To Other Devices*
One poster observed: “Finally have full access, full speed, and full functionality. Initially I installed the Time Capsule at the location of my cable, cable modem... which of course was next to my HDTV, DVD, Apple TV, Amplifier, etc. Get the picture? After about 4 weeks of starts and stops, resets and repeated initial backups, I moved the unit to another location, closer to my Mac, and in an area where there are no other electronics. Now, it runs perfect.” [http://discussions.apple.com/thread.jspa?threadID=1734818&tstart=0]
*Change Firewall Settings* #
Go to System Preferences --> Security.
Click the Firewall tab.
Change setting to “Set access for specific services and applications”.
The System will now ask you when each process wants to penetrate the firewall. Once you click “Allow” each time you are asked, it will be saved in the pane at the bottom of this window and it should never ask you again.
One poster observed, “Since I made this change, my wireless has been strong and Time Machine works like a champ and the impact on my network performance is minimal. I speculate that the change in performance is due to security protocols or services that run in the 'allow all incoming connections' and 'allow only essential services' modes. Whatever the reason this fix has worked for me for over 2 months without resetting my airport connection or time capsule.” [http://discussions.apple.com/thread.jspa?messageID=8348496#8348496]
*Change Time Capsules’ Channel*
Launch Airport Utility.
Select the device on the left.
Click "Manual Setup."
Select “Airport” in the toolbar.
Click the "Wireless" tab.
If “Channel” is set to “Automatic” try changing to a different one. Holding the Option key down and clicking the drop-down menu should provide more channels to choose from. If you have another wireless router operating, ensure that each devices’ channels are as far apart as possible.
Click “Update”.
Close Airport Utility.
*Preferred Networks & Airport Services*
You may be experiencing interference from other networks in your neighborhood. When you click the Airport menu are there other networks listed other than your own?
If so, is your network at the top of the list? It should be.
Go to System Preferences --> Network --> Select Airport on the left.
Click "Advanced". In the “Airport” tab note the various local wireless networks that Airport detects. Is the network you prefer to connect to at the top of the list? If not drag it to the top. Are there other networks you never intend to connect to (an old work network, or a neighbors network)? Then highlight them and click the "-" button.
Make sure “Remember any network this computer has joined” is checked.
Click "OK".
For "Network Name" be sure your network is selected and then click "Apply".
Is Airport (wireless) your primary means of connecting to your network? If so, is Airport at the top of the list of services on the left? It should be.
Click the small “Gear” button at the bottom of the window and select “Set Service Order”.
Now drag Airport to the top of the list.
Click “OK”. Click “Apply”.
Now see if network connectivity has improved.
*Transmit Power & Wide Channels*
If you are using the 802.11n only (5GHz) radio mode, you can also select to use wide channels, which provide higher data throughput in your network.
Launch Airport Utility
Select your Time Capsule on the left.
Click “Manual Setup”.
Select “Airport” in the toolbar.
Click the “Wireless” tab.
Click “Wireless Options...” at the bottom of the window.
Adjust the “Transmit Power” to 100%.
Put a check mark in the box labeled “Use Wide Channels”. (If you are using a 802.11a/b/g (2.4GHz) radio mode then select “Interference Robustness”)
Click “Done”.
Click “Update” in the lower right hand corner.
Wait for the Time Capsule to restart and then see if your network speeds improve.
*Faulty Airport Card*
One poster reported: “I reckoned the fault must be with the Macbook’s hardware so took the plunge and got a new airport card fitted to my Macbook and now everything is working fine. At last I have a working Macbook!” [http://discussions.apple.com/thread.jspa?threadID=1719326&tstart=0]
If you think this might be the case, follow the steps outlined in this KB article to determine if your Airport card is still being detected by your system:
[http://support.apple.com/kb/HT2601]
Let us know if any of the above helped improve your situation.
Cheers!

IPad does not appear in iTunes Devices list

My MacBook Pro, iPhone, and iPad are all on the same network, however my iPad frequently does not appear in iTunes Devices when not physically connected by USB. No problem with my iPhone. Anyone else with this problem? Any solution? (Yes, all OS/iTunes softwares are current.)
Further detail, to temporarily fix this issue, I physically connect my iPad via USB to sync it. Temporarily the iPad will be seen in the device list allowing sycing to occur while remotely charging, but at some random time later my iPad is no longer found by iTunes - again without the physical USB link. So, yes there is a work around, but it is annoying to be so up and down with this feature.
Any ideas are appreciated.

iPad not appearing in iTunes
http://www.apple.com/support/ipad/assistant/itunes/
iOS: Device not recognized in iTunes for Mac OS X
http://support.apple.com/kb/TS1591
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
iTunes for Windows: Device Sync Tests
http://support.apple.com/kb/HT4235
IOS: Syncing with iTunes
http://support.apple.com/kb/HT1386
Apple - Support - iPad - Syncing
http://www.apple.com/support/ipad/syncing/
 Cheers, Tom

My Time Capsule does not work with existing WiFi

Following a question solved on March 24 by LaPastenague, but gone bad again.
Apple AirPort Time Capsule
I felt the need for a physical backup of my data, as I would not completely trust the different clouds. I use, and have used Dropbox for 4-5 years and are very satisfied with that, but I am still not sure if or when a political lunatic will shut off the internet.
I purchased the Apple AP Time Capsule 2T, because all my other stuff are Apple, and that it's wireless. My old backup is Maxtor 300 GB.
Since we stay 2-3 weeks on two locations, one in Norway and one in Sweden (two different countries) we must use Mobile Broadband 4G, cables or fibre connections are useless for us, and we don't have it up to the houses. I have one mini router for each country, we bring with us iPhones, iPads, iMac, Apple TV, APExpress. When we pass the boarder I change the mini router, and the system continues working perfect on the WiFi, except the APExpress that needs to be reconfigured, but then it works.
The APTC was difficult to make working as it would not accept to be in an existing network, but with good help from the Apple Community, LaPastenague, with forcing the TC connect to the APE with Ethernet cable in bridge mode, ref "My Time Capsule does not work with existing WiFi" from March 24, the problem was solved and all gadgets worked together in a perfect harmony, until we changed location.
Now, as I have my second WiFi network, and the APExspress is reconfigured, it's like the TC thinks, I am the base boss here, I am not taking orders from APE one more time, and it simply does not work, not only that, it fluctuates all the time.
I have a slight feeling that the two WiFi bands are making the trouble as during the configuration of the TC sometime the last figure 6 and 7 pops up, and that has something two do with the two different 2,4 and 5 GHZ bands
So, I am curious if you have any idea ?
I am thinking of returning the TC if I don't make it work now, but how do I delete all the data that's on it?

I can deal with the last question first and easily.
I am thinking of returning the TC if I don't make it work now, but how do I delete all the data that's on it?
Open the airport utility .. go to the disk tab and select erase.
When you select erase you will get mulitiple options.
Quick removes the file table but does not delete the files,, it takes 2min or less.
A Zero out data is the secure way,, by writing 0 ie low level drive format.
It can take several hours..
7 pass will take a week.. not recommended..
35 pass erase is ridiculous.. it would take a month.. put an ax through the TC. It is quick and better.
Now, as I have my second WiFi network, and the APExspress is reconfigured, it's like the TC thinks, I am the base boss here, I am not taking orders from APE one more time, and it simply does not work, not only that, it fluctuates all the time.
The fact that it did work and has now failed might point to faulty unit.
The only way to tell is reset it properly to factory and start over.
Universal Factory Reset.. any model TC or AE.
Unplug your TC/AE from power or turn off at the power point.
Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
Note..
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
Generally having multiple wireless AP should not cause problems.. but it is better to set channels manually.. so it doesn't go beserk rotating channels.
Remember to keep all names short, no spaces and pure alphanumeric.
Sadly though the Apple routers have no logging now and no SNMP and almost nothing to help diagnose a problem, so if it continues .. take it back to apple.. they have given you no other method of fixing it.

HT1414 HOw do I back up and restore If I plug my ipod in and it does not appear in the devices column. I have a white screen and i'm trying to fix it and nothing is working :(

How do I back up and restore my ipod touch if when i connect it to itunes It does not appear in the devices column? I have a white screen and have tried holding down the wake/sleep and home buttons and that is not working. Please help

Take it in for repair/replace to your local Apple retailer.

HT201263 My iPod touch is stuck in recovery mode, but when I connect it to my computer to restore it, my computer does not recognize it. It does not appear as a device in my iTunes. What can I do to restore it/make my computer recognize it?

My iPod touch is stuck in recovery mode, but when I connect it to my computer to restore it, my computer does not recognize it. It does not appear as a device in my iTunes. What can I do to restore it/make my computer recognize it?

DId it successfully connect to this computer before?
Try:
iOS: Device not recognized in iTunes for Windows
or
V
Also try placing the iPod in DFU mode and then try restoring
iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X

[solved] SD card in my card reader does not appear as a device

Greetings.
I have an Asus EEE 1015PEM netbook, which has a built-in card reader.
I found some old SD cards that I am trying to get files from. When I insert them into the SD card reader in my netbook, the SD card does not appear as a device, and thus, I cannot mount it.
sh-4.3$ ls /dev/sd*
/dev/sda /dev/sda1 /dev/sda2 /dev/sda3
sh-4.3$ lsusb
Bus 001 Device 002: ID 13d3:5702 IMC Networks UVC VGA Webcam
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 13d3:3315 IMC Networks Bluetooth module
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
sh-4.3$ # insert card
sh-4.3$ sleep 10
sh-4.3$ ls /dev/sd*
/dev/sda /dev/sda1 /dev/sda2 /dev/sda3
sh-4.3$ lsusb
Bus 001 Device 002: ID 13d3:5702 IMC Networks UVC VGA Webcam
Bus 001 Device 010: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 13d3:3315 IMC Networks Bluetooth module
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Come to think of it, I am not sure I ever tried my SD card reader since I installed Arch on the machine (the machine was running Ubuntu before that, and there, inserting an SD card would trigger some automount magic).
You guys know what I can do to access the files on my SD cards?
Cheers,
Willard.
Last edited by willardthor (2014-06-08 17:13:35)

Trilby wrote:
And
uname -a
pacman -Qs linux
sh-4.3$ uname -a
Linux fenrir 3.14.4-1-ARCH #1 SMP PREEMPT Tue May 13 16:41:39 CEST 2014 x86_64 GNU/Linux
sh-4.3$ pacman -Qs linux
local/alsa-lib 1.0.27.2-1
An alternative implementation of Linux sound support
local/alsa-utils 1.0.27.2-1
An alternative implementation of Linux sound support
local/archlinux-keyring 20140220-1
Arch Linux PGP keyring
local/aura-bin 1.2.3.4-1
A secure package manager for Arch Linux and the AUR written in Haskell - Prebuilt binary
local/iptables 1.4.21-1
Linux kernel packet control tool
local/keyutils 1.5.9-1
Linux Key Management Utilities
local/kmod 17-1
Linux kernel module handling
local/lib32-alsa-lib 1.0.27.2-1
An alternative implementation of Linux sound support (32 bit)
local/lib32-libxshmfence 1.1-1
a library that exposes a event API on top of Linux futexes (32-bit)
local/lib32-util-linux 2.24.1-1
Miscellaneous system utilities for Linux (32-bit)
local/lib32-v4l-utils 1.0.1-1
Userspace tools and conversion library for Video 4 Linux (32-bit)
local/libimobiledevice 1.1.6-1
Is a software library that talks the protocols to support iPhone and iPod Touch devices on Linux
local/libiodbc 3.52.9-1
Independent Open DataBase Connectivity for Linux
local/libutil-linux 2.24.2-1 (base base-devel)
util-linux runtime libraries
local/libva 1.3.1-1
Video Acceleration (VA) API for Linux
local/libxshmfence 1.1-1
a library that exposes a event API on top of Linux futexes
local/linux 3.14.5-1 (base)
The Linux kernel and modules
local/linux-api-headers 3.14.1-1
Kernel headers sanitized for use in userspace
local/linux-firmware 20140316.dec41bc-1
Firmware files for Linux
local/lirc-utils 1:0.9.0-71
Linux Infrared Remote Control utils
local/man-pages 3.68-1 (base)
Linux man pages
local/mdadm 3.3-2 (base)
A tool for managing/monitoring Linux md device arrays, also known as Software RAID
local/mplayer 37051-2
Media player for Linux
local/pacman-mirrorlist 20140531-1
Arch Linux mirror list for use by pacman
local/pipelight 1:0.2.7-1
A browser plugin which allows one to use Windows only plugins inside Linux browser
local/syslinux 6.03pre12-3
Collection of boot loaders that boot from FAT, ext2/3/4 and btrfs filesystems, from CDs and via PXE
local/util-linux 2.24.2-1 (base base-devel)
Miscellaneous system utilities for Linux
local/v4l-utils 1.0.1-1
Userspace tools and conversion library for Video 4 Linux

HT201263 When I connect to itunes it does not appear in the devices..please help me ........how...its URGENT...

When I connect to itunes it does not appear in the devices..please help me ........how...its URGENT...

Here:
iOS: Device not recognized in iTunes for Windows
or
iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X

My ipad has been disabled and when connected to the pc it is recognized as a camera and it does not appear under itunes devices,really want to get it abled how do i tackle this?

my ipad haas been disabled and whe connected to the computer it is recognised as a camera,plus it does not appear under itunes devices,i really want to get it working,what is the solution to this,thanks in advance

Hello popsicles,
This first article should be helpful in getting iTunes to recognize your iPad once more:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
If the device is still disabled once it's appeared in iTunes again, please reference this second article:
iOS: Forgotten passcode or device disabled after entering wrong passcode
http://support.apple.com/kb/HT1212
Cheers,
Allen

Time machine does not appear to backup an external HD. how do I get that included in the backup?

time machine does not appear to backup an external HD. how do I get that included in the backup?

In the Finder, press the key combination shift-command-C, or select
Go ▹ Computer
from the menu bar. A window will open showing all mounted volumes. Select the one in question and open the Info window. What is shown as the Format in the General section? If it's not "Mac OS Extended," Time Machine can't back up the volume.

Time capsule does not appear in shared devices

Similar Messages

Maybe you are looking for