Time Capsule Network and Airport Extreme Configuration

I have a hybrid wireless and wired network in my home. TC is my primary router. I have a switch hanging off of the TC that distributes the ethernet around the home. To extend my wireless reach with an Airport Extreme, can/should I 1) plug the Airport into ethernet at the opposite end of the home, or 2) connect the Airport wirelessly to the TC? What are the implications of both?

The letters (N, B, G) refer to the speed of the wireless network. The higher the letter (N currently) the faster the wireless network. The Airport Extreme & TC's currently sold are the 802.11N version, 802.11 is just a number and refers to a set of standards for wireless local area network. Therefore if you here 802.11 you know they are referring to a wireless network and what ever letter follows (B,G and now N) referrs to the speed of that network. However remember this works at the lowest common denominator. What I mean by that is let's say you have a wireless router (like TC) that works at N speeds and you want it to communicate with a wireless printer but that printer is B speed well your router is going to adjust to the B speed so it can communicate to the printer.
Hope this helps a little.
Roger

Similar Messages

  • Can I extend Time Capsule network with Airport Extreme

    I have a new 2TB TimeCapsule, I would like to extend my network to the front of my house via Ethernet and an Airport Extreme basestation. The wireless reception in the front room is almost non existant, but I do have an Ethernet cable from the existing TimeCapsule connected to my iMac in the front room. I would like to add the old Airport Extreme Base Station to the front room and connect the Ethernet to the Wan port of the AEB and then connect the iMac and my Apple TV to the Ethernet port on the AEB.
    I cannot connect via Airport Wireless due to metal studs, Cement block walls.
    Is this possible?
    Thanks

    Is this possible?
    Yes. This type of configuration is called a "roaming network"
    Apple's instructions for this type of setup are here:
    http://support.apple.com/kb/HT4260

  • I have a airport time capsule, an older airport extreme, and an airport express.  I want to hard wire my Mac Mini to the network.  What is the best arrangement of the devices?  which ones should be hard wired to optimize extending the network?

    I have a airport time capsule, an older airport extreme, and an older airport express.  I want to hard wire my Mac Mini to the network.  What is the best arrangement of the devices?  which ones should be hard wired to optimize extending the network?

    I am using TM Unifi with an ASUS RT-N18U Wi-Fi router.  I would like to know could I use Apple AirPort Time Capsule to extend (repeater, booster) my Wi-Fi to a part of the house where the Wi-Fi signal is poor
    Yes,, if you plan to connect the AirPort Time Capsule to the ASUS router using an Ethernet cable connection that will remain fixed and permanently installed at all times.
    No, if you were planning to have the AirPort Time Capsule connect wirelessly and extend the Asus WiFi signal, since it would not be compatible with another manufacturer's router for that purpose.
    Another way of saying the same thing here would be that if you want to extend the network wirelessly, it will take two Apple routers to do so

  • Extend present Time Capsule network with an Extreme

    I currently have a wireless network in my house using a Time Capsule that is connected to the modem in the office. I bought a Blu-Ray player that is connected to my TV in the living room, and if I plug it directly in to a router using an ethernet cable, I can stream movies to my TV. Sooooo.....I found the old Airport Extreme I used before I bought the Time Capsule, and I would like to use it to extend my network to the living room. I have the Extreme plugged in right now by the BLu-Ray player, and the name I used for the old Extreme network is showing up on my laptop, as well as the new Time Capsule network. The Extreme is blinking amber. What do I need to do to just add this Extreme as an extension of my network so I can connect it to my Bu-Ray via a ethernet. Thanks.

    Since you have the 802.11n AirPort Extreme Base Station (AEBSn), you can take advantage of the "extend a network" feature.
    o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
    o Open AirPort Utility and select the base station that will connect to the Internet.
    o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
    o Click AirPort in the toolbar, and then click Wireless.
    o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
    o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
    o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
    o Enter the base station network and base station password is necessary.
    o Click Update to update the base station with new network settings.
    (ref: Page 46 of "Designing AirPort Networks Using AirPort Utility.)

  • Can Time Capsule backup an Airport Extreme's attached USB hard drive?

    Can Time Capsule backup an Airport Extreme's attached USB hard drive (without currently being attached to a MAC OSX LION system)?

    No, sorry.. there is no way for the TC to see the files.. and even if you plug the hard disk into the TC there is no mechanism in the TC to drag the files to itself.. The TC is absolutely a dumb network attached drive.. everything you want to do must be done from a computer.

  • Can I backup to a time capsule via an airport extreme.

    I have a time capsule although it is at the other side of my house and i dont get great signal. I am looking at getting an airport extreme (would an airport expres to extend my signal. Will i be able to backup to my time capsule via my airport extreme.

    If your Time Capsule was purchased in the last few years, chances are you have a simultaneous dual band Time Capsule.
    In order to extend both bands using wireless only, you would need a new AirPort Extreme, since the AirPort Express would only be able to extend one band from the Time Capsule.
    If you only need to have one band extended, then an AirPort Express would likely work for your application.
    Whether you choose the Extreme or Express, keep in mind that the correct location for an extending device is a point that is approximately half the distance from the Time Capsule and the general area that needs more wireless coverage.
    Apple's instructions to configure the "Extend" setup are here. Although an AirPort Extreme is pictured in the example, the instructions for an AirPort Express would be the same.
    http://support.apple.com/kb/HT4259

  • I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn't support this base station. Go to AirPort Service and Support for more information."

    I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information." Any thoughts?

    This sounds as if you have an older AirPort Express that is no longer supported by the newer Mavericks operating system.
    To check and see if  that might be the case, locate the model number on the side of the AirPort Express. It will start with an "A" followed by four numbers. Hard to see in the faint print.....so you may need reading glasses or a magnifying class to see the model number clearly.
    Model numbers A1084 and A1088 of the AirPort Express are no longer supported by AirPort Utility in Mavericks.
    You will need to use a Mac running Leopard, Snow Leopard, or a PC to be able to administer the older AirPort Express.

  • Settings for Roaming Network using Time Capsule plus old Airport Extreme

    Hi all
    I am trying to set up a network in the most effective way for my home and am experiencing some difficulties which I hope your support can help me overcome.
    My home is constructed of concrete reinforced with steel and consequently the walls are dense and wireless signals are adversley affected. I have two wireless base stations via which I hope to provide wireless coverage to my whole home which is on the ground floor level only. My Time Capsule is located at one end of my home and is directly connected to my modem which receives the external fibre optic supplied internet connection. The Time Capsule is managed via Airport Utility 6.1. A mac is connected to the Time Capsule via ethernet cable - the Time Capsule also provides a wireless signal. Also connected to the Time Capsule via a long ethernet cable that is routed in internal cable channels within my home is an old conical shaped white Airport Extreme. The Airport Extreme is located at the other end of my house and also has a mac connected to it via ethernet and provides a wireless signal too. The Airport Extreme is managed via Airport Utility 5.6.
    I hope to have a wireless network that my iphones and ipad can connect to in various areas of the house. I have read the instructions for setting up a Roaming Network, yet the screen shots provided do not reflect the screens I see using Airport Utility 5.6 and 6.1. Can anyone please assist with the settings that I require?
    Also I have a question regarding a roaming network  - if I connect a mobile device to the wireless network near to my Time Capsule and then move to the other end of my house near to the Airport Extreme what should happen to the wireless connection strength? Currently with my existing settings the mobile device is maintaining the connection to the Time Capsule and dropping to extremely low connections levels rather than picking up the wireless signal from the Airport Extreme. Should this be the case and if so is there some better way to set up my network?
    Originally I had the Airport Extreme configured in a different location closer to the Time Capsule to extend the wireless network from the Time Capsule. The problem was that the Airport Extreme frequently seemed to not provide the newtork. I'm not sure if it lost the network from the Time Capsule or had some other problem.
    All help will be greatly appreciated.

    So just to be clear.. the Mac at the other end of the house.. has internet connection.. via ethernet.. through the old extreme.. ethernet to the TC.. which is connected via ethernet to the fibre connection.
    Is the airport extreme in bridge mode?
    As long as it is, you are good to go.
    On both the TC and AEBS you create a wireless network.
    On both TC and AEBS you name it the same.. eg 24ghz (please use short, no space, pure alphanumeric name).
    You set both with the same security.. WPA2 Personal
    You set both with the same passkey.. 8-12 characters pure alphanumeric.
    BUT you set the wireless channels.. there are three channels that do not overlap.. 1, 6, 11 (13 in europe ME??)
    Suggest you set TC to 6.. and set the AEBS to 11.
    It might work on auto but IMHO wireless is something you are better controlling than leaving it to dumb algorithm

  • Time capsule to extend airport extreme base station

    I have an airport extreme base station dual band that I use to create a wireless network. I use a first generation time capsule single band to extend the wireless network. In the area of my home where the time capsule is my ipad and macbook the signal strength of the wifi is great and works great however my iphone 4 works horribly on wifi in the same room where the time capsule is located. Why is this? And is there a better configuration that would work better?

    The AirPorts are all designed to try to extend the 5 GHz signal because that is the fastest connection. But, because 5 GHz signals are not as strong as 2.4 GHz signals, it's usually the 2.4 GHz network actually that winds up being extended because it's the stronger signal of the two bands and the extending device is usually located at some distance from the main router.
    If your Time Capsule is extending the 5 GHz band, that's impressive. The AirPort Express would also probably extend the 5 GHz band if you placed it in the same area. Unfortunately, the iPhone cannot connect to that signal and must get it's connection from the main router. If you set things up so that the Time Capsule extends 2.4 GHz, then the iPad and your Mac will be running at significantly lower speeds.
    It can be done by assigning a different name to the 5 GHz network and I can give you the steps. Is that what you want to do?
    If you reversed the Time Capsule and AirPort Extreme, you'll have to set the Time Capsule up at 2.4 GHz and the AirPort Extreme will only extend 2.4 GHz. It cannot extend both 2.4 GHz and 5 GHz since it won't "see" that signal from the Time Capsule. No reason to do this really.

  • Time Capsule green and Airport Express blinking amber

    I replaced my AEBX with a Time Capsule and now the AEX configured as an extender blinks amber continuously. Bringing up AirPort Utility and following the AU help instructions to find out why the blinking amber, shows that the AEX is operating normally. In fact, the little faux LED to the left of the AEX icon shows green while the real LED is blinking amber.
    The AEX was solid green before installing the TC.
    Anyone else seen this? Anyone know what's going on?

    I cannot get Airport Utility to see both my Time Capsule and my Airport Express at the same time. When I disconnected from the Time Capsule network it saw the AEx but repeatedly said there was a problem configuring the device. So I am stuck.

  • Time Capsule (Tower) and Airport Express

    I have a new Time Capsule (Tower) and want to extend the range in my house using an Airport Express.  However, I cannot get the A/E to connect, and I cannot see the A/E when I open the Airport Utility.  What am I doing wrong. Thanks.

    Unfortunately, extending using wireless is going to result in a significant speed reduction on the network.
    Power off both AirPort Express devices
    Wait a minute
    Power up the A1264 for a minute or two
    Hold in the reset button on the Express for 8-10 seconds and release
    Allow a full minute for the Express to restart to a slow, blinking amber light
    On your Mac, click on the AirPort icon at the top of the screen
    Click on AirPort Express under the setting of New AirPort Base Station
    The setup utility will open up. Follow the prompts
    Set up the other Express the same way.

  • Time capsule network AND modem possible with maverick?

    Hey all. At home I have a small time capsule network at home and use a Huawei modem to connect to the internet. Since the update to mavericks it is impossible to run both at the same time. Now I have to choose between internet connection (Huawei) and my local network (time caps). How can I connect to them both at the same time again? Thanks.

    Hi, jackthebulldog. Welcome to the forums!
    What happens if you enter 192.0.32.10 into Safari's address bar? Does it still load the Comcast activation page, or does it go to a page with some text about "example.com"?
    Message was edited by: adsfushi72

  • How do I add an airport extreme to existing time capsule network and be able to use the router ethernet ports?

    Good day everyone.  I recently upgraded my airport extreme network by replacing the base station with a time capsule router.  Since I now have an "extra" airport extreme router, I've set it up on the other side of the house to both extend the wireless range as well as use it's LAN ports for a home theater system in that location.  Connecting the two routers was done via ethernet.  It now appears that I need to do something "else" as the LAN ports on the now relocated airport extreme are nonfunctional.  All devices are operating well for wireless and as a review, the modem is connected to the time capsule WAN which is connected to the airport extreme via ethernet cable via LAN to it's WAN port.  What do I need to change on configurations to get the LAN ports functioning on the airport extreme?  Thank you for any help.

    Connecting the two routers was done via ethernet.  It now appears that I need to do something "else" as the LAN ports on the now relocated airport extreme are nonfunctional.
    With both base stations interconnected by Ethernet you have the basis for a "roaming" type network. If properly configured, both base stations' Ethernet ports would be enabled for wired clients.
    The key configuration items for a roaming network are as follows:
    All base stations used must be interconnected by Ethernet.
    The "main" base station; the one connected to the Internet modem, must be configured to provide both NAT & DHCP services; all other base stations used must be configured as bridges (NAT & DHCP disabled.)
    Each base station must have a unique base station name.
    Each base station must use the same wireless security type and password.

  • Setting up Time Capsule with existing AirPort Extreme 802.11n and AirPort Express.

    I already have and am using an AirPort Extreme 802.11n with an AirPort Express. I want to set up a Time Capsule 802.11n. Which is the best way to configure this?

    ... Which is the best way to configure this?
    The answer depends on what you need the TC to accomplish. If all you need it to do is perform Time Machine backups, simply have it join your existing network in client mode. It would be if it were to connect to your existing router (presumably your Extreme), not through an "extended" wireless network (presumably your Express).
    If you need the TC to "extend" your network so as to serve additional wireless clients, you can do that also. Configure it to "extend" the network created by your Extreme.
    As you can see it's quite versatile.

  • Can't Get Time Capsule to Extend Airport Extreme Wireless Network

    I've searched this forum and read dozens of listings, but nothing I've found gives me a answer for the problem I'm having.
    I had an existing network consisting of three Airport Extreme routers, one the master/DHCP server and the other two to extend the network. All of the routers were configured for 802.11n 5 GHz only service.
    After much frustration trying to use Time Machine to back up to external disks attached to Airport Extremes as well as disks attached to other Macs, I gave up and bought a Time Capsule.
    I have been trying for about six months on and off to get the Time Capsule configured as an extension to the main Airport Extreme as the other two Extremes are.
    Nothing I've tried will cause the TC to extend the network. It always comes up with a yellow light and error messages saying that there is a problem with the wireless network and a problem with the internet connection and, sometimes, a third message that I don't remember.
    After my initial efforts, I just gave up and plugged the danged TC into the remote AE that is closest to where I use my MacBook Pro and it worked. But I wanted it to REPLACE that AE instead of being an appendage to it.
    Due to TC/TM problems, I've twice lost the entire TM backup off of the TC, and tonight I decided it was time to start over. I've encountered the same problems as before, and so finally moved the TC to my home office rack where the main AE is located and plugged it into the AE directly. TM is now backing up, but at a snail's pace (which is why I wanted the TC to be located in the same room where I use the laptop).
    Has anyone had success or failure extending a multiple-unit AE network with a TC on 802.11n 5 GHz (not WDS)? If not, has your experience been similar to mine; if so, what did you do that I haven't?
    Any specific help will be greatly appreciated.

    Yes, I suppose I could do that. But if the wireless extension isn't working in one direction there's no guarantee it'll work in the other direction; and I was trying to avoid upending my entire setup.
    And no, I'm not bridging the units with hard-wired cabling; I'm attempting to use wireless to extend them...NOT WDS, which is for 802.11B/G mode, but the 802.11N wireless extension mode that's available on these Apple products.

Maybe you are looking for