Time Capsule on roaming

Hi Everyone. I need help. I noticed I am downloading at half the speed when my laptop in roaming on my Time Capsule(wireless download). The main AExtreme(connected to broadband modem)has a download speed of 600KB/s but the Time Capsule is only downloading at 300KB/s. They are all hard wired CAT6 with Gigabit switches and on roaming. My Time Capsule is on Bridge Mode while Airport Extreme is main router connected to DSL modem. Did I do anything wrong?
Also, my Time Machine wireless backup doesnt work when I move to the Time Capsule. It only works with the main AEBS. Message says to check IP address....The "data" folder of Time Capsule wont mount on my Finder. My setup is on gigabit roaming mode, Time Capsule on Bridge Mode. Thank you for your help.

As stated it should work.. but it is easy to test.. swap the TC for airport and see if reversed things work ok. The process of elimination is the best way to find where the problem exists.. since you have the ability to just swap devices and their roles. do it.

Similar Messages

Home setup - network switch and 2 Time Capsules

I have an ADSL modem/router (Billion BIPAC 5200G). I have used it previously with wireless turned off. I then used a time capsule in bridge mode so that NAT etc is turned off, and then use it to broadcast wifi and as a backup. It is attached to the modern with ethernet. It worked fine.
I am now in a house with a lot of ethernet ports, linked to a massive hub thing. But it needs a switch to link it all together.
So I am thinking of this setup:
PHONE LINE
to
BILLION ROUTER (Set as a router with wifi turned off)
to
NETWORK SWITCH
to
VARIOUS ethernet enabled devices in different rooms (i.e. printers, Apple TV, TV, Time capsule)
Then I want to use my 2nd time capsule to extend my ground floor network by plugging it in essentially directly into the time capsule via ethernet in roaming mode.
Is this the optimal setup for this? My other idea was to forgo the network switch and do it this way:
PHONE LINE
to
BILLION ROUTER (Set as a router with wifi turned off)
to
VARIOUS ethernet enabled devices INCLUDING the TIME CAPSULE and PRINTER.
then:
To the TIME CAPSULE:
to
VARIOUS ethernet enabled devices INCLUDING Imac, Apple TV and another TIME CAPSULE in roaming mode.
My main questions are: which setup will give me better speeds to all devices. Ie: is the switch even necessary? In my 2nd example, will the first time capsule and printer be available to the Imac.
There seems to be no real advantage to having the TIME CAPSULE in router mode while keeping the BILLION ROUTER as a pass through with NAT off (To avoid Double NAT) except for the guest network capabilities.
If its just simpler to have the network switch, then perhaps that's the way to go. If so: any suggestions on network switches that work well?

It doesn't allow me to select ethernet as an option for internet connection, only dchp, ppoe and one more which isn't ethernet.
DHCP is correct setting. .it will use ethernet but the new AC TC has problems.. it needs a crossover cable with some switches. Or you need to return it and get it replaced as there is something wrong with its wan port.. the new AC model needs a hardware revision and about 3 or 4 firmware upgrades before it hits the status of the Gen4 it replaced.
My questions are: should I connect my time capsules together directly with ethernet using another available port in my new time capsule. I thought my switch would work better. Also, does one time capsule have to be in router mode instead of having both of them in bridge.
Both should be in bridge.. but you can rearrange things to see if any of the other devices works better.
You can use the billion or the old TC.. plug the new TC into those.
Bob is correct though.. the switch is the correct thing for everything to be plugged into .. but in home situation what works is more important than what is best. It if fails in all of them then the WAN port is proven faulty.
Should I be able to use the hdd on the 2nd (older) time machine as essentially a networked hdd for putting movies and music on, and use my new time capsule as the sole backup (occurring both over ethernet for my iMac and wifi for our laptops)
Yes, that is ok.. you just need to get the AC version TC actually working properly.
Give us a few screenshots of things.. that really helps to see.
Click on each unit and show the summary pages.

Airport Extreme + Time Capsule Roaming Network

Ok, I'm completely lost here and haven't found any solutions specific to my situation. I currently have two ethernet jacks in my condo, both have fiber optic internet connection which provide access when connected to a computer and no router. I'm assuming there is a router somewhere in the building but alas it's not in my unit.
My home office is in the den where I have one ethernet jack. Connected to the jack is my airport extreme (dual band, 7.5.1 software). The second jack is located in the living room where I have my Time Capsule connected. I have it set this way because the wireless signal from the den does not extend well into the living room.
Basically I have two jacks, a TC and an AE and I'd like to create a roaming network. Both of them are set to bridge mode with the same SSID, WPA2 security, same password, etc. When I open airport utility on my main computer I can see both the AE and TC which is good because I have files I need to access for work on the TC. The problem I have is some of the wireless devices will not get an internet connection but instead get the self assigned IP address. My iPhone and iPad work all the time as well as the xbox and PS3 that are hardwired into the TC. Macbook laptop only connects about 1 out of every 4 times and other guests with iPhones have been getting the self assigned IP too. It's confusing because sometimes the devices connect flawlessly and sometimes they don't.
Sorry for the long-winded post but this situation has been very irritating for a couple months so I thought I'd finally seek answers here. I guess my basic question is what is the proper setup for an AE and a TC roaming network using two different ethernet jacks with no modem in my unit?

Welcome to the discussion area, Junkcanoe!
I don't have a setup like yours, but might be able to offer some assistance.
Basically I have two jacks, a TC and an AE and I'd like to create a roaming network. Both of them are set to bridge mode with the same SSID, WPA2 security, same password, etc.
This would be the normal way to set up a roaming network, but the wild card here is that we don't know anything about how the main router that supplies the ethernet connections (valid IP addresses) to the condos might be configured.
For example, most apartments, hotels, etc that provide ethernet jacks usually limit the number of devices that can connect to each jack. Hotels tend to limit this to one or two devices. I counted six devices that you say will work properly plus a few more. Since you have two separate ethernet jacks, you may be looking at a situation where each jack is allocated a total of 4 devices, or valid IP addresses.
The bottom line here is that we won't be able to make much progress until we know more how the main router there has been configured. Is it possible for you to ask the complex manager (who will probably need to ask the IT guy) how many devices are allowed to connect per ethernet jack? Another way to ask the same question is how may valid IP addresses will each ethernet jack allow?
If you can, could I ask you to perform an experiment? Rather than have both the AirPort Extreme and Time Capsule each connect to a separate ethernet jack, can you temporarily move one device near the other and connect them together using an ethernet cable? (Or, use a long ethernet cable if you don't want to move either device) LAN <-> port on one to LAN <-> port on the other. In other words, you'll only be using one of the ethernet ports in the condo for this experiment.
Any difference in performance or number of devices allowed to connect?
Message was edited by: Bob Timmons

Time Capsule on a Roaming Network

Hello everyone,
Quick and hopefully simple questions.
I just bought a 2TB time capsule. Is there any good reason to setup partition(s)? My household has 1 iMac and 3 Macbooks. Would it be good to have a separate partition for each machine? I am also open to having some network attached storage on the time capsule but don't find it absolutely nessasary.
Lastly I plan on setting up a roaming network using my airport extreme(connected to the cable modem) and then run cat 6 to the time capsule and 2 other airport express units to get great wifi coverage throughout my house. Anyone have any tips or advice on this setup? I have checked the apple support site and understand the confing involved in setting up the roaming network, just wanted to poll the forums for any helpful advice.
Thanks for your time!!

Quick and hopefully simple questions.
I just bought a 2TB time capsule. Is there any good reason to setup partition(s)? My household has 1 iMac and 3 Macbooks. Would it be good to have a separate partition for each machine? I am also open to having some network attached storage on the time capsule but don't find it absolutely nessasary.
Answers are simple.. There is no way to partition a TC. Not without voiding warranty and removing the drive and doing it on a computer .. then returning the drive to the TC. So don't do it.
You do not need to have separate partitions for each machine.. if you are going to use Time Machine as most people do, each computer will create its own sparsebundle which is kind of virtual disk partition. Each computer will use only its own sparsebundle and everything will be kept isolated from each other.
I am not sure what you mean by using NAS .. do you mean a separate NAS plugged in or a USB drive or using some of the TC internal disk space for file sharing?? The later is not a great idea. TM and data do not generally get on too well.. And the TC is a backup target for TM.. it has no way to back itself up, nor can TM backup a network drive. So any files on the TC are not backed up.
See pondini .. our TM guru master for all things TM.
Basic info. http://pondini.org/TM/FAQ.html
See particularly Q3 here for sharing TM and data.
http://pondini.org/TM/Time_Capsule.html
Lastly I plan on setting up a roaming network using my airport extreme(connected to the cable modem) and then run cat 6 to the time capsule and 2 other airport express units to get great wifi coverage throughout my house. Anyone have any tips or advice on this setup? I have checked the apple support site and understand the confing involved in setting up the roaming network, just wanted to poll the forums for any helpful advice.
Roaming is a good setup. Not a lot that goes wrong.
BUT.. IMHO.. and it is that..
Setup the whole wireless network using simple names.. no spaces pure alphanumeric.
Since every unit gets the same SSID.. I do recommend a lot more manual control.. I simply don't trust the automagical system to work.
You have only 3 non-overlapping channels at 2.4ghz.. 11, 6, 1 and you need to setup each unit on one of those channels.
There are more channels at 5ghz and the range is poor so they tend to interfere less.. but AC wireless uses 80mhz and even N uses 40mhz. So take care to spread things.. and you decide. Hence I use separate names for 2.4ghz and 5ghz so I can force clients to use band I choose.. not the one they choose.
Be experimental.. no one setup is ideal for everyone.. and since wireless is about 80% straight voodoo then try a few arrangements and see what works well for you. Be prepared to wipe the whole thing out and start over.. keep track of all the options you try in a log. (that is the science part.. log the voodoo!!)

HT4260 Airport extreme and time capsule connection order in a roaming network

I plan to create a roaming network with my current Airport Extreme as the primary device connected to the internet and the new Time Capsule as the secondary device in Bridge mode. The connection between AE and TC will be wired (ethernet). Then I plan to connect the PC that needs backing up to the Time Capsule with an ethernet cable. Apart from the PC-backup functionality, I'd like to use the Time Capsule as a central NAS-device in my network. All other wired network devices that need access to the NAS (Apple TV, Xtreamer) are currently connected to the primary Airport Extreme with ethernet cables. My question: is there any reason why I should consider reversing the setup order, i.e. making the Time Capsule the primary device connected to the internet and the Airport Extreme the secondary device? Would this have a positive or negative effect on Time Capsule functionality and performance in the network? Thanks in advance for your thoughts!

Your Gen3 Extreme and all TC are gigabit.. as long as you connect with the required standard cable to have a gigabit connection between the two, there will effectively be no difference. In a home network you will struggle to saturate gigabit no matter what you do. Although the difference between the two configurations is really very small.
General rule is keep whatever is using the highest bandwidth closest and directly connected to whatever it is using.. shrug.. in this case you can follow or not.. it is more a guideline.

Time Capsule/Airport Express/Ethernet - Setting up Roaming Network?

Hi,
I am trying to setup a network in my house to extend the wifi. Currently the wifi signal is not strong enough to work in the a portion of the upstairs (bonus room). I want to extend the network and have it be as fast as possible.
Here's what I have going on:
There are 2 rooms hard wired with cat 5. The office and the upstairs bonus room. I have a comcast modem in the basement where the cat 5 wires all run to. The comcast modem has three available ethernet out ports. I have one of them running to my office where my time capsule is located which is where I currently have my wifi signal coming from. I have another ethernet plugged into another port on the comcast modem and running to the bonus room. I purchased a Airport express and was hoping to just plug it into the ethernet in the bonus room to extend my extisting network using the ethernet (via a roaming network?) but I can't get it to work.
A couple of questions:
Is this the best way to extend my network so it will be as fast as possible? How do I get it to work? I don't want to have to move the time capsule downstairs to make this work.
I am new to this type of networking so please forgive my ignorance.
Thanks in advance for the help.

Get the IP of the TC and the Express plugged into the Comcast router.. we are assuming router.
You simply click on the airport utility and see what IP it is picking up.
eg
This is bridged and has picked up the address from the main router.. so shows both LAN and IP address as the same.
Actually post a screenshot makes this ever so much easier.
If you are not getting this.. then click edit and go to the tabs..
1. Internet. Should be DHCP
2. Network. Should be Off (bridge mode)
3. Wireless. Should be Create a wireless network.
Post me up the details and "we" can work it out.
The basic Apple doco for roaming is here.
http://support.apple.com/kb/ht4260
As with so much documentation it is out of date against the newest version of the airport utility.. so they are a little behind.

Settings for Roaming Network using Time Capsule plus old Airport Extreme

Hi all
I am trying to set up a network in the most effective way for my home and am experiencing some difficulties which I hope your support can help me overcome.
My home is constructed of concrete reinforced with steel and consequently the walls are dense and wireless signals are adversley affected. I have two wireless base stations via which I hope to provide wireless coverage to my whole home which is on the ground floor level only. My Time Capsule is located at one end of my home and is directly connected to my modem which receives the external fibre optic supplied internet connection. The Time Capsule is managed via Airport Utility 6.1. A mac is connected to the Time Capsule via ethernet cable - the Time Capsule also provides a wireless signal. Also connected to the Time Capsule via a long ethernet cable that is routed in internal cable channels within my home is an old conical shaped white Airport Extreme. The Airport Extreme is located at the other end of my house and also has a mac connected to it via ethernet and provides a wireless signal too. The Airport Extreme is managed via Airport Utility 5.6.
I hope to have a wireless network that my iphones and ipad can connect to in various areas of the house. I have read the instructions for setting up a Roaming Network, yet the screen shots provided do not reflect the screens I see using Airport Utility 5.6 and 6.1. Can anyone please assist with the settings that I require?
Also I have a question regarding a roaming network - if I connect a mobile device to the wireless network near to my Time Capsule and then move to the other end of my house near to the Airport Extreme what should happen to the wireless connection strength? Currently with my existing settings the mobile device is maintaining the connection to the Time Capsule and dropping to extremely low connections levels rather than picking up the wireless signal from the Airport Extreme. Should this be the case and if so is there some better way to set up my network?
Originally I had the Airport Extreme configured in a different location closer to the Time Capsule to extend the wireless network from the Time Capsule. The problem was that the Airport Extreme frequently seemed to not provide the newtork. I'm not sure if it lost the network from the Time Capsule or had some other problem.
All help will be greatly appreciated.

So just to be clear.. the Mac at the other end of the house.. has internet connection.. via ethernet.. through the old extreme.. ethernet to the TC.. which is connected via ethernet to the fibre connection.
Is the airport extreme in bridge mode?
As long as it is, you are good to go.
On both the TC and AEBS you create a wireless network.
On both TC and AEBS you name it the same.. eg 24ghz (please use short, no space, pure alphanumeric name).
You set both with the same security.. WPA2 Personal
You set both with the same passkey.. 8-12 characters pure alphanumeric.
BUT you set the wireless channels.. there are three channels that do not overlap.. 1, 6, 11 (13 in europe ME??)
Suggest you set TC to 6.. and set the AEBS to 11.
It might work on auto but IMHO wireless is something you are better controlling than leaving it to dumb algorithm

Poor Time Capsule Performance in a Roaming Configuration

I have a bit of an odd problem. I recently added a Time Capsule (4th Gen) to my network alongside my existing Airport Extreme (4th Gen). Both devices are set in Bridge Mode and connected to a 1000Base-T backbone which accesses the Internet through my AT&T U-Verse gateway (WiFi off). My intention is to have the devices in a roaming network with the AE upstairs and the TC downstairs in my office.
Coverage-wise this has been excellent, but performance has not been up to par. Through a great deal of troubleshooting, hair-pulling, and even a replacement TC, I have determined that, for some reason, the TC has trouble forwarding my frames if it is on the same SSID as the AE. (Which is, of course, a required for a real roaming network.)
Both devices are running 7.6 firmware and I have manually set the radio channels at the far extremes from each other in both bands to rule out interference. My neighbors' APs are still visible, but aren't causing any intereference in those bands.
If I configure both devices with identical WiFi settings (SSID, WPA2-Personal, PSK, etc.) devices that are associated with the TC experience very poor performance. The radio part of the connection is great. (Strong signal, low noise, etc.) Data throughput is awful, though. Web pages won't load, and when I ping local devices on the wired side of the network I'm lucky to get 500ms round-trip. Most of the pings are in the >1000ms range with many timeouts.
Devices connected to the AE, however, average about 1ms round-trip to the same devies and see no issues getting to the Internet or transfering files locally. In fact, Time Machine backups work just fine to the TC.
That said, if I simply change the SSID for the TC radio, leaving *everything else* the same, it works like a dream. Unfortunately, that isn't exactly the roaming network I would like to have.
Has anybody else seen this behavior or have any ideas on how to fix it? I'm stumped. What really concerns me is that I've seen this with two different TCs.
For the record, I have already reflashed, defaulted, and configured both devices from scratch with no change in performance.

Replying to my own post is probably bad juju, but I thought I'd provide an update for those who may have also seen this issue.
First, it turns out that having the separate SSIDs didn't actually matter. WIthin a day or two of my OP, the Time Capsule on the separate SSID began exhibiting the same problem as before. It seems that this is part of the problem. When it occurs it can take a few days to a week to turn up, but it can also happen right away.
Eventually, the Time Capsule began to exhibit other issues as well. For instance, in my testing, I would need to reboot it to apply new settings, but it would hang on a reboot for 20 minutes or more and I would have to pull the power cable. I finally called Apple and they replaced it again.
When the new Time Capsule arrived, everything seemed to work well, but before I was even able to get the backups moved from the old one to the new one, the problem showed up on the new one.
At this point, I found a few forum threads where other people were having similar problems and were able to get around them by downgrading form firmware 7.6 to 7.5.2. I was about to try that when Apple released 7.6.1.
On a whim, I decided to try the new release, even though Apple only referred to vague WiFi performance fixes. I have to say that I noticed immediate improvement across the board.
So far, so good. I am hopeful that the new 7.6.1 is the fix to the problem.

My iMac will not connect to time capsule used as base station in my roaming network

I have a network that is made of up a Time capsule as a base station and 3 airport express's used to extend my wifi coverage. It is setup as a roaming network with each express hardwired to the base time capsule. I have a iMac that will not connect to the base station, it will only connect to one of the remote express's. The iMac is next to the base satation. Other mac notebooks, iPhone or iPads all connect to the base station when they are near it. Only my iMac will not connect to it. Any suggestions as to why this is happening or steps I can take to fix this.

Hello FoxFamilyVA
Check out the first article below to go through some troubleshooting options to get your iMac to connect to your Time Capsule. I would go through and remove it from the list of known networks that you join and then add it back in. I would also recommend that you try and create a new Network Location to see if there is an issue with your current configuration.
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Using network locations (Mac OS X v10.6 and later)
http://support.apple.com/kb/HT5289
Regards,
-Norm G.

HT4260 Can an Airport Extreme be used to form a roaming network with Time Capsule?

I tried the on-line instructions above to extend my Wi-Fi network with a roaming network but the graphics in the instrucions apparently show an earlier version of Airport Utility. Following the intent of the instructions, e.g., ethernet cable connection ports, etc., all I have achieved is a yellow flashing light on Airport Extreme. Airport Extreme has been reset to factory settings but it is not seen by the network.
Do I have it backward, for example, should the Airport Extreme be the base station and the TIme Capsule be the extended station?
What do you think I am doing wrong? Or, is this an impossible extension?
Thanks, Chad

Suggest that you use the much more functional and useful AirPort Utility 5.6 for Mac OS X Lion which was released at the same time as AirPort Utility 6.0.
Keep both 5.6 and 6.0 on your Mac and use the one that you want.
Post back if you need more assistance.

I enabled the guest network feature on my time capsule. Can I configure my airport extremes guest network feature if I use this as a network extender using a "roaming" network?

I enabled the guest network feature on my TC. Can I configure my airport extremes guest network feature if I use the extreme as a network extender connecting my Airport Extreme to my TC via ethernet cable?

Unfortunately no, since the AirPort Extreme should be configured in Bridge Mode if it is connecting to the Time Capsule using an Ethernet connection.
The Guest Network option cannot be enabled when the AirPort is configured in Bridge Mode.
Another way of saying the same thing is that the Guest Network cannot be "extended" either by using an Ethernet connection or wireless. It is only available from the Time Capsule "main" wireless router on your network, not any extending devices.

I want a new and more powerful (non-Apple) wireless router but I still want to use my existing Time Capsule to continue with my Time Machine backups and I still need the Time Capsule's Network Attached Storage (NAS) features and capabilities

THE SHORTER STORY
My goal is to successfully use my existing Time Capsule (TC) with a new and more powerful wireless router. I need a new and more powerful wireless router in order to reach a distant Denon a/v receiver that is physically located in a master bedroom some 50 feet away from my modem. I need to provide this Denon a/v receiver with an Internet connection so that it can obtain its firmware updates and I need to connect this Denon a/v receiver to my network in order to use its AirPlay feature. I believe l still need the TC's Network Attached Storage (NAS) features because I am not sure if the new wireless router will provide me with the NAS like features / capabilities I need to share files between my two Apple laptops with OS X 10.8.2. And I know that I absolutely need my TC's seamless integration with Apple's Time Machine (TM) application in order to continue to make effortless backups of my two Apple laptops. To my knowledge nothing works with TM like Apple's TC. I also need the hard disk storage space built into the TC.
I cannot use a long wired Ethernet cable connection in this apartment and I cannot use power-line adapters. I have read that wireless range extenders and repeaters are difficult to successfully set-up and that they will reduce data speeds, especially so when incorrectly set-up. I cannot relocate my modem and/or primary base station wireless router.
In short, I want to use my TC with my new and more powerful wireless router. I need to stop using the TC to connect to the modem. However, I still need the TC for seamless TM backups. I also need to use the TC's built in hard drive for storage. And I may still need the TC's NAS capabilities to share files wirelessly between laptops because I am assuming the new wireless router will not provide NAS capabilities for OS X 10.8.2 (products like this/non-Apple products rarely seem to work with OS X 10.8.2/Macs to provide NAS features and capabilities). Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone please advise on how to set-up my new Asus wireless router with my existing TC in such a way to accomplish all of this?
What is the best configuration or set-up to accomplish my above goals?
Thank you in advance for your assistance!!!
THE FULL STORY
I live in an apartment building where my existing Time Capsule (TC) is located in my living room and serves many purposes. Specially, my TC is at least all of the following:
(1) Wi-Fi router connected to Comcast Internet service via Motorola SB6121 cable modem - currently the TC is the Wi-Fi base station that connects to the modem and has the gateway address to the Internet. The TC now provides the DHCP service for the Wi-Fi network.
(2) Wireless router providing Internet and Wi-Fi network access to several Wi-Fi clients - two Apple laptop computers, an iPod touch, an iPad and an iPhone all connect wirelessly to the Internet via the TC.
(3) Wired Ethernet router providing Internet and Wi-Fi network access to three different devices - a Panasonic TV, LG Blu-Ray player and an Apple TV each use one of the three LAN ports on the back of the TC to gain access to the Internet.
(4) Primary base station in my attempt to extend my wireless network to a distant (located far away) Denon a/v receiver requiring a wired Ethernet connection - In addition to the TC, which is my primary base station, I am also using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. I cannot use a wired Ethernet connection to continuously travel from the living room to the master bedroom. The distance is too great as I cannot effectively hide the Ethernet cable in this apartment.
(5) Time Machine (TM) backup facilitator - I use my TC to wirelessly back-up two Apple laptops using Apple's Time Machine (TM) application. However, I ran out of storage space on my TC and therefore added external storage to it. Specifically, I added an external hard drive to my TC via the USB port on the back of the TC. I now use this added external hard drive connected to the TC via USB as the destination storage drive for my TM back-ups. I have partitioned the added external hard drive, and each of the several partitions all have enough storage space (e.g., each of the two partitions used by TM are sized at three times the hard drive space of each laptop, etc.). Everything works flawlessly.
(6) Network Attached Storage (NAS) - In addition to using the TC's Network Attached Storage (NAS) capabilities to wirelessly back-up two Apple laptops via TM, I also store other additional files on both (A) the hard drive built into the TC and (B) the additional external hard drive connected to the TC via USB (there are additional separate partitions on this drive for these other additional and non-TM backup files).
I use the TC's NAS feature with my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Again, everything works wirelessly and flawlessly. (Note: the Apple TV is connected to the network via Ethernet and a LAN port on the back of the TC).
The issue I am having is when I try to listen to music via Apple's AirPlay in the master bedroom. This master bedroom is located at a distance of two rooms away from the TC's current location in the living room, which is a distance of about 50 feet. This apartment has a long rectangular floor plan where each room is connected to the next in a straight line. In order to use AirPlay in the master bedroom I am using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. This additional base station connects wirelessly to the WiFi network provided by my TC and then gives my Denon receiver the wired Ethernet connection it needs to use AirPlay. I have tried moving my iTunes music directly onto my laptop's hard drive, and then I used AirPlay on this same laptop to connect to the Denon receiver. I always get a successful connection and the song plays, but the problem is that the connection inevitably drops.
I live in an apartment building and all of the many wireless routers in this building create a great deal of WiFi interference on both the 2.4 GHz and 5GHz bands. I have tried connecting the Netgear product to each the 2.4 and 5 GHz bands, but neither band can successfully maintain a wireless connection between the TC and the Netgear product. I also attempted to maintain a wireless connection to an iPod touch using the 2.4 GHz band and AirPlay on this iPod touch to play music on the Denon receiver. Again, I was able to establish a connection and successfully play music, but after a few minutes the connection dropped and the music stopped playing. I therefore have concluded that I have a poor wireless connection in the master bedroom. I can establish a connection, but it is intermittent with frequent drops. I have verified this with both laptops by working in the master bedroom for an entire day on both laptops. The Internet connection in this master bedroom proved to drop out frequently - about once an hour with the laptops. The wireless connection and the frequency of its dropout are far worse with the iPod touch and an iPhone.
I cannot relocate the TC. Also, this is an apartment and I therefore cannot extend the range of my network with Ethernet cable (I cannot drill through walls/ceilings, etc.). It is an old building with antiquated wiring and power-line adapters are not likely to function properly, nor can I spare the direct power outlet required with a power-line adapter. I simply need every outlet I can get and cannot afford to block any direct outlet.
My solution is to use a more powerful wireless router. I found the ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router which will likely provide a better connection to my wireless Internet in the master bedroom than the TC. The 802.11ac band of this Asus wireless router is totally useless to me, but based on what I have read I believe this router will provide a stronger connection at greater distances then my TC. And I will be ready for 802.11ac when it becomes more widely available.
However, I still need to maintain the TC's ability to work seamlessly with TM to backup my two laptops. Also, I doubt the new Asus router will provide OS X 10.8.2 with NAS like features and capabilities. Therefore, I still would like to use the TC's NAS capabilities to share files on my network wirelessly assuming the Asus wireless router fails to provide this feature. I need a new and more powerful wireless router, but I need to maintain the TC's NAS features and seamless integration with TM. Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone advise on how to set-up my existing TC with this new Asus wireless router in such a way to accomplish all of this?
Modem
Motorola SB6121 SURFboard DOCSIS 3.0 Cable Modem
Existing Wireless Router and Primary Wi-Fi Base Station - Apple Time Capsule
Apple Time Capsule MC343LL/A 1TB Sim DualBand (purchased June 2010, likely the Winter 2009 Model)
Desired New Wireless Router and Primary Wi-Fi Base Station - Non-Apple Asus
ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router
Extended Wi-Fi Base Station - Provides an Ethernet Connection to a Denon A/V Receiver Two Rooms Away from the Modem
Netgear Universal Dual Band Wireless Internet Adapter for TV & Blu-Ray (WNCE3001)
Addition External Hard Drive Attached to the Existing Apple Time Capsule via USB
WD My Book Studio 4TB Mac External Hard Drive Storage USB 3.0
Existing Laptops on the Wireless Network Requiring Time Machine Backups
MacBook Air (11-inch, Mid 2012) OS X 10.8.2
MacBook Pro (13-inch Mid 2010) OS X 10.8.2
Other Existing Apple Products (Clients) on the Wireless Network
iPod Touch (second generation) is model A1288.
iPad (1st generation)
Apple TV (3rd generation) - Quantity two (2)

Thanks Bob Timmons.
In regards to a Plan B, I hear ya brother. I am already on what feels like Plan Z. Getting WiFi to a far off room in an apartment building crowded with WiFi routers is a major pain.
I am basing my thoughts on the potential of a new and more powerful router reaching the far off master bedroom based on positive reviews on cnet.com, pcmag.com and pcworld.com. All 3 of these web sites have reviewed the Asus RT-AC66U 802.11AC wireless router as well as its virtual twin cousin 802.11n router. What impressed me is that all 3 sites rated this router #1 overall in terms of both range and speed (in both the 802.11n and 802.11AC flavors). They tested the router in real world scenarios where the router needed to compete with a lot of other wireless routers. One of the sites even buried this Asus router in a media room with thick walls and inside a media cabinet. This Asus router should be able to serve my 2.4 GHz band wireless clients (iPod Touch and iPhone 4) with a 2.4GHz Wireless-N band offering some 50 feet of dependable range and a 60 Mbps throughput at that range. I am hoping that works, but it's borderline for my master bedroom. My 5 GHz wireless clients (laptops) will enjoy a 5GHz Wireless-N band offering 150 feet of range and a 200 Mbps throughput at that range. I have no idea what most of that stuff means, but I did also read that Asus could reach 300 feet and I got really excited. My mileage may vary of course and I'm sure I'm making some mistakes in my interpretation of their data. However, my Winter 2009 Time Capsule was rated by cnet.com to deliver real world performance of less than that, and 802.11AC may or may not be useful to me someday. But when this Asus arrives and provides anything other than an excellent and consistent wireless signal without drops in the master bedroom it's going right back!
Your solution sounds great, but I have some questions. I'm using OS X 10.8.2 and Airport Utility (version 6.1 610.31) and on its third tab labeled "Wireless" the top option enables you to set "Network Mode" to either:
Create a wireless network
Extend a wireless network
Off
Given your advice to "Turn off the wireless on the TC," should I set Network Mode to Off? Sorry, I'm clueless in regards to how to turn off the wireless on the TC any other way. Can you provide specific steps on how to turn off the wireless on the TC? If what I wrote is correct then what should the rest of this Wireless tab look like, or perhaps it is irrelevant when wireless is off?
Next, what do you mean by "Configure the TC in Bridge Mode?" Under Airports Utility's fourth tab labeled "Network" the top option "Router Mode" allows for either:
DHCP and Nat
DHCP Only
Off (Bridge Mode)
Is your advice to Configure the TC in Bridge Mode as simple as setting Router Mode to Off (Bridge Mode)? If yes, then what should the rest of this "Network" tab look like? Anything else involved in configuring the TC in Bridge Mode or is it really as simple as setting the Router Mode to "Off (Bridge Mode)"?
How about the other tabs in Airport Utility, can they all stay as is assuming I use the same network name and password for the new Asus wireless router? Or do I need to make any other changes to the TC via Airport Utility?
Finally, in regards to your Plan B suggestion. I agree. But do you have a Plan B for me? I would greatly appreciate any alternative you could provide. Specifically, if you needed a TC's Internet connection to reach a far off corner of your home how would you do it? In the master bedroom I need both a wired Ethernet connection for the Denon a/v receiver and wireless Internet connection for the iPhone and iPod Touch.
Power-Line Adapters - High Cost, Blocks at Least One Wall Outlet and Does Not Solve the Wireless Need
I actually like exactly one power-line adapter, which is the D-Link DHP-540 PowerLine AV 500 4-Port Gigabit Switch. This D-Link power-line adapter plugs into your wall outlet with a normal sized plug (regular standard power cord much like any other electronic device) instead of all of the other recommended power-line adapters that not only use at least one wall outlet but also often block the second outlet. You cannot use a power strip with a power-line adapter which is very impractical for me. And everything about my home is strange and upside down. The wiring here is a disaster and I don't have faith in its ability to carry Internet access from the living room to the master bedroom. And this D-Link power-line adapter costs $90 each and I need at least two to make the connection to the Denon A/V receiver. So, $180 on this solution and I still don't have a dependable drop free wireless connection in the master bedroom. The Denon might get its Ethernet Internet connection from the power-line adapter, but if I want to use an iPhone 4 or iPod Touch to stream AirPlay music to the Denon wirelessly (Pandora/iTunes, etc.) from the master bedroom the wireless connection will not be stable in there and I've already spent $190 on just the two power-line adapters needed.
Extenders / Repeaters / Wirelessly Extending the Wireless Network
I have also read great things about the Amped Wireless High Power Wireless-N 600mW Gigabit Dual Band Range Extender (Repeater) SR20000G and the My Net Wi-Fi Range Extender. The former is very powerful and the latter is easier to install. Both cost about $150 ish so similar to a new Asus router. However, everything I read about Range Extenders points to them not being very effective for a far off corner of your house wherein it's apparently hard to place the range extender in the sweet spot where it both gets a strong enough signal to actually effectively extend the wireless signal and otherwise does not reduce network throughput speeds to unacceptable speeds.
Creating a Roaming Network By Hard Wiring with Ethernet Cable - Wife Would Say, "**** No!"
Even Apple seems to warn against wirelessly extending your network (see: http://support.apple.com/kb/HT4145#) and otherwise strongly recommends a roaming network where Ethernet cable is used to connect two wireless base stations. However, I am in an apartment where stringing together two wireless base stations with Ethernet cable would have an extremely low wife acceptance factor (WAF). I cannot (both contractually and from a skill prospective) hide Ethernet wire in the walls or ceiling. And having visible Ethernet cable running from room-to-room would be unacceptable, especially to the wife.
So what is left? Do you have a Plan B for me? Thanks in advance for your help!

How do I connect my time capsule with a Lynksis wi fi netwotk?

How do I connect my time capsule with a Lynksis wi fi netwotk?

You cannot extend or repeat a non-apple router in an apple router..
You must plug it in via ethernet and then setup roaming network (or if you like a completely separate network.. makes no difference from the TC point of view). TC is in bridge mode. That is router bridge not wireless bridge.. I gave the info on the other thread you are running.. very confusing when you ask in multiple threads.

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network?

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network? I have an ISP provided wireless Router that has to remain as the base station. I am able to join my 1/2TB Airport Extreme and Airport Express to the network, but I can't access/use Time Machine.

One option would be to connect the Time Capsule (TC) to the ISP-provided wireless router by Ethernet. You can then configure the for a roaming network. Then, depending on what your goal is for the AirPort Express, you can either: 1) Add it to roaming network, 2) Configure the TC & the Express for an "extended" network, or 3) Configure the Express to "join" the roaming network for AirPlay.

Access to Time Capsule in Bridge Mode from outside of the network

I have a Time Capsule with an external hard drive set up in bridge mode on my home network. The main router and DHCP server is an Actiontec MI424, and is specific to my ISP (Verizon, required for TV Guide info from Fios) so the Time Capsule's AirPort can't be used as the primary. I need to access the external hard drive from outside my network (I.E. the internet), but I'm having trouble figuring out which ports are required for Sharepoint to work.
So far I've forwarded 548, but I get an error "-36" when I try to connect from the outside. It works fine on the inside. Any suggestions?
Thanks, JSD

The Express units can extend wireless on the TC or each other.. but they cannot extend wireless on the Asus anyway..
So the setup is Asus--TC (that has to be ethernet) The TC in bridge mode.
Then TC -- express can be done by ethernet in roaming mode as bob listed above or extend wireless.
I am guessing.. what model are the express units.. they are older Gen1 N model ??
IMHO the TC is simply no longer viable.. replace it with one express as the AP and extend it with the other Express.. see if that works better.
But I would be trying to use the wireless just from the AC66U.
I would also force the Asus back to 20mhz on the 2.4ghz band.. so you can provide adequate channel separation.. 40mhz wireless on 2.4ghz works poorly anyway because you have too much wifi .. there is very limited number of non-overlapping channels.. ie 3. 11, 6 and 1.

Time Capsule on roaming

Similar Messages

Maybe you are looking for