Time Capsule shows error message "Conflicting DHCP Range."

I just set up a wireless network using a Time Capsule as the main router with an Airport Extreme bridged to it so I can have a strong signal downstairs. It all worked fine at first, but at some point the Time Capsule showed this error message on Airport Utility: "Conflicting DHCP Range."
The instructions that pop up when I click on the error message are beyond my level of understanding. They say: "This Airport base station rejected a DHCP address in the same subnet as its internal DHCP server. Try switching your Airport Base Station from using DHCP and NAT to bridge mode. If you still want to use DHCP and NAT to share a single IP address, change your DHCP range."
Could one of you tell me what I should do? Thanks.

Try switching your Airport Base Station from using DHCP and NAT to bridge mode.
I suggest that you do what AirPort Utility suggests.....
Open up AirPort Utility, click on the AirPort Express and click Edit in the smaller window that appears
Click the Network tab at the top of the window
Insure that the setting for Router Mode is set to "Off (Bridge Mode)"
Click Update to save the settings and give the AirPort Express a minute to restart

Similar Messages

Download error under apps. After following download steps multiple times still showing error message.

Download error under apps. After following download steps multiple times still showing error message.

Hi There,
Kindly try the below mentioned links.
Creative Cloud Help | Download Error in Apps tab of Creative Cloud Desktop Application
Creative Cloud - Download error - stubborn error
Thanks,
Atul Saini

Time Capsule disconnected error messages

MacBook Air 2011
I used to have a Time Capsule (2nd generation, I think) that eventually died on me, so I've removed it.
Now I keep getting annoying error messages when starting Chrome:
These delay the start of Chrome as I have to click ok two or three times, often delaying it by up to a minute. Super frustrating.
My Time Machine is turned off and I have deleted the Time Capsule as a backup server, so not sure why it's trying to connect.
Any help would be appreciated.

The message is not from chrome though.
You need to check that there is no other reference to the TC in the system.
Check in Finder under Go Connect to server and delete anything there.

Time capsule unexpected error message using maverick and utility 6.3

I have a TC 3TB new in last year. I had it set up a to join my home wireless network, it is connected via ethernet to my iMac, and it has been working fine. I updated to mavericks last week and everything was still working fine. Until yesterday. Now my TC is not recognized. I've tried to hard reset it several times and set it up to join as before, I've tried to restore previous settings, and set up a new network, none of these have worked. I continue to get the same message, "an unexpected error occurred" and to try again.
Any suggestions?

AirPort Utility won't let me change the router mode. In fact, I can't even get to the menu shown in the picture you've posted. The button "Other Options", if this should be the way, is innactive...
You need to get in.. connect by ethernet dongle.. and make sure you have an IP from the TC..turn off wireless in the MBPr.
Then if you cannot get into the device do a factory reset.
See instructions on reset.. http://support.apple.com/kb/ht3728
In simple terms.. hold in reset and THEN power on the TC.. keep holding reset until the front led flashes rapidly .. about 10sec. no data is lost from hard disk.
Select the TC in the airport utility
Info on the unit appears. Then click on edit.
That gets you to the manual setup screen..
One last question. For option 1 (all I need is using TC just to back up stuff from my MBPr automatically via Time Machine), should I connect the TP-Link modem/router to the WAN port of TC or to one of its 3 ethernet ports?
Thanks again
In bridge it makes no difference.. but by convention we use WAN to connect to modem.. it helps to keep things clear when you troubleshoot.. but when you bridge.. WAN port is assigned to LAN.
Spell checking is always fun here.. but I refuse to follow the US convention even if normal spell check is forced to US on the website.. my posts always have lots of spelling errors. !!!

How do I resolve "Conflicting DHCP Range"?

How do I resolve "Conflicting DHCP Range"?

Hello Dorohidea,
Do you mean that when you install crystal report in virtual studio 2010, you receive the error message about error 1310?
Please take a look at the following KB.
Support for Crystal Reports for Visual Studio
https://support.microsoft.com/kb/317789/en-us
In Visual Studio 2010, to create a Crystal Reports project or Web site or to import existing projects or Web sites that were created by using older versions of Visual Studio or Crystal Reports, you must first install a version of Crystal Reports that is
compatible with Visual Studio 2010.
For more information about how to use Crystal Reports in Visual Studio 2010, visit the following SAP Crystal Reports website:
http://www.sap.com/crystalreports/vs2010
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

ABAP dump coming at the time of displaying error message.

Hi to all
I have written a code in user exit .
At the time of saving ABAP dump is coming instead of showing error message.
Error analysis
    The program attempted to issue a " " message during "Exit Command" processing.
This is an illegal operation. The program was terminated.
Screen name.............. "SAPMV45A"
Screen number............ 4008
My coding :
>>>>>     IF vbak-vkbur IS NOT INITIAL.
   70       IF wa-vkbur NE vbak-vkbur.
   71         MESSAGE E000(yi01) WITH 'SALES OFFICE Mismatch Please Check for Customer-'vbak-kunnr
   72       ENDIF.
   73     ENDIF.
Please guide to resolve the issue.
This application is working fine for sales order creation.
Regards
Anubhav

Hi
Instead of error message, try using the following code.
MESSAGE <your message> TYPE 'I' DISPLAY LIKE 'E'.
Thanks
Sourav

Time Capsule shows up as Computer in Sidebar

Hi,
Each time after the iMac waked up from sleep the sidebar-icon of the Time Capsule has changed to the icon for a normal computer (Monitor). Restarting the Finder helps to show the correct icon (little Time Capsule) but after the next sleepmode the wrong icon is back.
This happens just on one MAC in the network, the others are showing the correct icon at any time even after waking up from sleep.
I've searched the web over and over and it seems that some other people have the same issue sometimes (i.g. here: https://discussions.apple.com/message/10731493#10731493) but I never found a solutuion for that.

Hi,
I have the same issue. Time Capsule shows up as both a Time Capsule (with correct icon) and as a PC File Server...
Could it be because i've used it to transfer files, over the air, from my old PC laptop to an iMac?
Anyone have an idea about this?

Time Capsule not visible when connecting via range extender

Hi,
I have configured a TP-Link WA750RE to expand the range of my Time Capsule's wireless network. The range extender works fine for surfing the web etc., but the Time Capsule doesn't show up as my Time Machine backup device and the Time Capsule is not visible in my Airport Utility. What's even stranger is that when I click on "Configure other" (shift + command + o) in Airport Utility and type in my Time Capsule's IP-address and password, I can still access the devices' configuration menu.
When I move my Macbook very close to my Time Machine to connect directly to the wireless network, leaving out the range extender, none of the above mentioned problems occur. The TP-Link range extender has no NAT or port configuration that could possibly cause this problem, so I'm out of ideas for a way to solve this problem.
Thank you in advance for your help.

A non-apple range extender is not passing the protocols that apple uses.. eg bonjour.. This is a standard problem and why you stick with using Apple's own routers for extensions.

HT3275 Time Capsule backup error

I am getting an error while backing up with Time Capsule.
The message: "The backup disk image “/Volumes/Data/XXXXXXXX’s MacBook Pro.sparsebundle” is already in use."
What does it mean?

It means you are more than likely running Mountain Lion (or Lion).
And your Networking has now reached the limits of ML.. ie wet string.
Reboot the whole network.. start in order modem.. tc.. clients. With 2min gap between.
Read C12 http://pondini.org/TM/Troubleshooting.html
You are only the 4th person today with the issue.

How to update Ipad 2 from IOS 4.3.5 to IOS 5. Itunes won't let me do it because it keeps showing error messages asking me to check if my network is active.

how to update Ipad 2 from IOS 4.3.5 to IOS 5? Itunes won't let me do it because it keeps showing error messages asking me to check if my network is active.

If you have an iPad 1, the max iOS is 5.1.1. For newer iPads, the current iOS is 7.1.2. The Settings>General>Software Update only appears if you have iOS 5.0 or higher currently installed.
You can no longer update to iOS 6.x, or down grade the iOS.
iOS 5: Updating your device to iOS 5 or Later
http://support.apple.com/kb/HT4972
How to install iOS 6
http://www.macworld.com/article/2010061/hands-on-with-ios-6-installation.html
iOS: How to update your iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT4623
If you are currently running an iOS lower than 5.0, connect the iPad to the computer, open iTunes. Then select the iPad under the Devices heading on the left, click on the Summary tab and then click on Check for Update.
Tip - If connected to your computer, you may need to disable your firewall and antivirus software temporarily. Then download and install the iOS update. Be sure and backup your iPad before the iOS update. After you update an iPad (except iPad 1) to iOS 7.x, the next update can be installed via wifi (i.e., not connected to your computer).
Tip 2 - If you're updating via wifi, place your iPad close to your router to preclude getting a corrupted download.
How to Upgrade to iOS 7
The iOS 7.0 update requires around 2.5 GB of storage space, so if your iPad is almost full, you may need to clear up some space. You can check your available space in Settings -> General -> Usage.
There are two ways to upgrade to iOS 7: You can use your Wi-Fi connection, or you can connect your iPad to your PC and update through iTunes. We'll go over each method.
To upgrade using Wi-Fi:
Note: If your iPad's battery is under 50%, you will want to plug it into your charger while performing the update.
Go into the iPad's Settings.
Locate and tap "General" from the menu on the left.
The second option from the top is "Software Update". Tap this to move into the update settings.
Tap "Download and Install". This will start the upgrade, which will take several minutes and will reboot your iPad during the process. If the Download and Install button is grayed out, trying clearing up some space. The space required by the update is mostly temporary, so you should gain most of it back after iOS 7 is installed.
Once the update is installed, you may have to run through the initial steps of setting up your iPad again. This is to account for new features and settings.
To upgrade using iTunes:
First, connect your iPad to your PC or Mac using the cable provided when you purchased your device. This will allow iTunes to communicate with your iPad.
You will also need the latest version of iTunes. Don't worry, you will be prompted to download the latest version when you launch iTunes. Once it installs, you may be asked to setup iCloud by logging into your iTunes account. If you have a Mac, you may be prompted on whether or not you want to enable the Find my Mac feature.
Now you are ready to begin the process:
If you upgraded iTunes earlier, go ahead and launch it. (For many, it will launch automatically when you plug in your iPad.)
Once iTunes is launched, it should automatically detect that a new version of the operating system exists and prompt you to upgrade to it. Choose Cancel. Before updating, you will want to manually sync your iPad to make sure everything is up to date.
After canceling the dialog box, iTunes should automatically sync with your iPad.
If iTunes doesn't automatically sync, you can manually do it by selecting your iPad within iTunes, clicking on the File menu and choosing Sync iPad from the list.
After your iPad has been synced to iTunes, select your iPad within iTunes. You can find it on the left side menu under Devices.
From the iPad screen, click on the Update button.
After verifying that you want to update your iPad, the process will begin. It takes a few minutes to update the operating system during which time your iPad may reboot a few times.
After updating, you may be asked a few questions when your device finally boots back up. This is to account for new settings and features.
 Cheers, Tom

Airport Extreme - Conflicting DHCP Range - Only 1 router set up

Backstory:
I recently upgraded my router to the new Airport Extreme from an older Airport Extreme in order to take advantage of the Gigabit ports. The old router worked great, just wanted to take advantage of my 300mbps up/down speeds.
Problem:
My router is flashing orange and I get an error that pops up on my computer from the Airport Utility stating 'Conflicting DHCP Range'. Normally this problem occurs when there is more than one router/bridge on a single network. However, I have only the one router with no guest network set up. The wireless connection works fine, but an error pops up and interrupts me every few minutes and gets very annoying and the router is flashing orange, indicating a problem. We have tried turning on and off the 5GHz.
I've searched the forums front to back and have found others with this problem but only if they have more than one router set up on the same network.
We have 2 macbook pro retinas running OSX 10.8.3, an AppleTV, an HP printer, and 2 iPhone 5's that connect to the network.
What can I do to address this issue?!!??
Thank you,
Nick

When you configured the new AirPort Extreme, did you use the option to "Create a new network", or did you use the option to "Replace an existing device"?
Can you provide the make and model number of your modem?

When I switch my time capsule to 5.0ghz mode the range of my wireless network drops significantly. Near the Time Capsule my Macbook Pro works fine, in my bedroom I have almost no signal. In mixed mode it works fine. Any ideas on how to get 5.0 working?

When I switch my time capsule to 5.0ghz mode the range of my wireless network drops significantly. Near the Time Capsule my Macbook Pro works fine, in my bedroom I have almost no signal. In mixed mode it works fine both placed. Any ideas on how to get 5.0 working? I thought 5.0Ghz was supposed to have a wider range. Do I need to change a setting on the Macbook Pro?
Thanks, W

I'm not sure if you understand that 5 GHz has some upsides, but also some very significant downsides.
The upside is that the 5 GHz signal will allow faster speeds.
The downside is that you must always give up something in order to gain something else.Unfortunately, the marketing hype about 5 GHz does not go into very many details about this.
In the case of 5 GHz, the 5 GHz signals are much weaker than 2.4 GHz signals, so they do not travel as far or penetrate any obstructions like walls or ceilings nearly as well as 2.4 GHz signals. In many cases, in order to get good 5 Ghz performance, you literally have to have almost a line-of-sight relationship between your computer and the wireless router.
If you have a new dual band router, which broadcasts both a 2.4 GHz and 5 GHz signal simutaneously, your Mac will connect to the best signal quality automatically depending on its location in relation to the router. In the same room, without any obstructions, it will connec to 5 GHz. But, take the laptop down the hall a few rooms and around the corner and the Mac will connect to the 2.4 GHz signal because at that location, the 2.4 GHz signal is not only stronger, it is also faster.

How to show error message in a report program

Hello Guys,
I am making a report using smartforms. I am successful in showing data but problem is if if i put a value in parameters that does not exist is database, the smartform runs and related fields shows as empty fields. But the form is running. I want to show error message if the parameter values dose not matches with the database values. The message will show as Document not exists
So i used related error msg here like
if sy-subrc ne 0.
          message e357.
           endif.
But it is not working for passing values to smartform. It works if i use in classical report. Plz help me on this issue.
Thanks,
Rosaline.

>
Rosaline. wrote:
> Thanks all for reply. Should i have to use message before call function 'SSF_FUNCTION_MODULE_NAME' ? I tried it but not working.
>
>
if it_final[] is not initial.
>*             if sy-subrc ne 0. ---> "Remove this condition check, it not required
>            Message e000(8i) with 'Parameter value not found'.
>            endif.
> *            endif. ---> "remove this
>
Hi,
Sy-subrc doesnt need to be validated here, remove that If condition and check again.
Regards,
Karthik D

TS3638 i have an internet connection but when i open app store it shows error message "cannot connect to app store".when i try to sign in with my valid apple ID and password it says "connection failed".i tried keychain access settings but it did not help.

i have an internet connection but when i open app store it shows error message "cannot connect to app store".when i try to sign in with my valid apple ID and password it says "connection failed".i tried keychain access settings but it did not help.please help me!!

Open Sysem Preferences from your Apple () menu top left in your screen then select the Firewall tab.
Make sure the Firewall is turned off.

While trying to run it show error message : "The application or DLL C:\Program Files\Mozilla Firefox\sqlite3.dll is not a valid Windows image. Please check this against your installation diskette

Just updated firefox. While trying to run it show error message : "The application or DLL C:\Program Files\Mozilla Firefox\sqlite3.dll is not a valid Windows image. Please check this against your installation diskette." Tried to download and install new firefox, but it alway show that the file is corrupt
== Today ==
== User Agent ==
Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; InfoPath.2)

Do a clean reinstall and download a fresh Firefox copy from http://www.mozilla.com/firefox/all.html and save the file to the desktop.
Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
You can skip the step to create a new profile, that is not necessary for this issue.
See http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall

Time Capsule shows error message "Conflicting DHCP Range."

Similar Messages

Maybe you are looking for