Time capsule shows up in finder but I can't connect !!!

My time capsule shows up in finder under shared devices but when I click on it and it tries to connect it says 'connection failed' ( when out of home ) this is annoying as I would like to access the external hard drive that I have connected to it. I am having no problems at home with my LAN.

hello
No i'm connect via ethernet (cable) with TC. The problem is when I try to connect to my TC when I'm away from home like for ex. using a free wi fi spot!! Well in this case the icon appear on my Finder but refuse to connet!! ( connection faild ).

Similar Messages

Wants to use my Time capsule hard drive with Plogoplug but I can't... Any Idea on how to...?

Wants to use my Time capsule hard drive with Plogoplug but I can't... Any Idea on how to...?

If the TC is not the main router just bridge it.
Have you tried it with the TC bridged??
You need to describe the full network because we have no idea how all this is setup.

My Time Capsule hard drive shows up in Finder, but I can't access the disk. I get a connection failed message.

I can not access my Time Capsule from the Finder. This was working, but on 12/25/2011, the disk can no longer be accessed. It shows up in the Finder, but when I try to connect, I get a "Connection Failed" message. If I cycle the power, it works for a little while and then fails again.

hello
No i'm connect via ethernet (cable) with TC. The problem is when I try to connect to my TC when I'm away from home like for ex. using a free wi fi spot!! Well in this case the icon appear on my Finder but refuse to connet!! ( connection faild ).

Non-Existent Time Capsule Shows up in Finder Side Panel

hello --
i have this very strange finder behavior, which i cannot figure out how to fix. while playing around with my TC i had it renamed, and since i rightfully have Back to My Mac enabled the new share showed up in the finder side panel. I then renamed it back, but the old one stayed. I can neither connect to it or remove delete it. It only goes away when i turn off back to my mac, which doesn't make sense. I also tried removing my mobile me ID from the sharing prefs to the same result. The old share just doesn;t go away. any suggestions?
thanks.

Same issue. Cant get rid of the old name of the time capsule

Time capsule shows up as pc server in finder sidebar

no idea what is happening, but i just turned on my macbook, which is always connected to the time capsule, and it is recognizing my time capsule as a "pc server" and it doesn't have the normal little time capsule icon in the side bar in finder. has anyone had this problem? doesn't always let me connect either. thanks for any help you can give me.

Hi,
I have the same issue. Time Capsule shows up as both a Time Capsule (with correct icon) and as a PC File Server...
Could it be because i've used it to transfer files, over the air, from my old PC laptop to an iMac?
Anyone have an idea about this?

Time Capsule shows up as Computer in Sidebar

Hi,
Each time after the iMac waked up from sleep the sidebar-icon of the Time Capsule has changed to the icon for a normal computer (Monitor). Restarting the Finder helps to show the correct icon (little Time Capsule) but after the next sleepmode the wrong icon is back.
This happens just on one MAC in the network, the others are showing the correct icon at any time even after waking up from sleep.
I've searched the web over and over and it seems that some other people have the same issue sometimes (i.g. here: https://discussions.apple.com/message/10731493#10731493) but I never found a solutuion for that.

Hi,
I have the same issue. Time Capsule shows up as both a Time Capsule (with correct icon) and as a PC File Server...
Could it be because i've used it to transfer files, over the air, from my old PC laptop to an iMac?
Anyone have an idea about this?

Can Time Capsule show a connected USB hard drive?

Hi, I have just purchased 1TB Time Capsule, which supposes to show a external USB connected hard drive. But why there is no drive nor icon shows in Find after it connected to Time Capsule?
that USB hard drive just works fine with direct connection to my MBP.
thanks all.
Message was edited by: marvinclick

marvinclick wrote:
But why there is no drive nor icon shows in Find after it connected to Time Capsule?
in the finder, click on the icon of the TC under shared. a connection dialog will appear and you may have to enter your admin password. then click on the folder symbolizing your USB drive
that USB hard drive just works fine with direct connection to my MBP.
in case above does not work, check if your drive is formatted for Mac or FAT32. your TC will not recognize NTFS formatted drives ...
JGG

2. gen iPod nano sometimes shows up in Finder, but not in iTunes

Hi!
My brand new 8GB iPod nano that I got for christmas sometimes seems to have problems connecting to iTunes. Every now and then (perhaps 1/4 of the time?) it will show up in Finder, but not in iTunes (I haven't enabled "disk mode" yet, so when it shows up in iTunes, it is not visible in Finder). Also, on one or two occasions, it showed up in iTunes, but wasn't recognized.
Whenever this happens, I just eject the iPod from Finder and disconnect it, and on the second try (on one occasion - third try) it will show up in Finder.
What could this be? Bad connectors/cable - or iTunes just not very reliable?
MBP 15" C2D 15" 2.33/2/160 - MB (white) 2/2/120 - PBG4 12" 1.33/1.25/60 Mac OS X (10.4.8)

These problems return every now and then.
In addition, if the iPod is connected, is shown in iTunes and has already synced properly, it will sometimes reset if I try an additional manual sync from the File menu. It's a rather benign error, since it will connect and sync as soon as the iPod has restarted.
I also had one freeze of the iPod while playing.
This is my first iPod, and I'm used to computers that run for months or years without a reboot. Is it just normal for an iPod to freeze/reset every now and then? My Nokia phone does it too, but then I expect more from Apple...

I just purchased a 3TB Time Capsule. I live in Italy and have 220V power. The Time Capsule is rated for that, but the cord says 125V. Can I use this cord with an adapter, or do I need to buy a new cord at an Italian store?

I just purchased a 3TB Time Capsule. I live in Italy and have 220V power. The Time Capsule is rated for that, but the cord says 125V. Can I use this cord with an adapter, or do I need to buy a new cord at an Italian store?

Due to the kind of plug used the US power cord is rated at the 125v value.. and legally we cannot advise you to use on higher voltages.. although I have never had issues in Australia.. 240v.
But adapters from your Euro power plug to US are generally ugly .. unsightly things.. and often sit high above the socket and are none too stable.. I agree with Bob.. just go out and buy a standard figure 8 power cord.. check with Apple in Italy for a white one.. if you are going to have it on show.. black are far more common. Or even check ebay for a standard power Apple power cord as a number of items they sell use the figure8 socket.

My ipad is freez...it only show a fome screen. but i can turn off my ipad but not shut down...and i went to my computer and i go to itune. i try to restart my ipad but it say turn off your.find my iphone..but i cant my ipad is freezing.can help me plz.

my ipad is freez...it only show a fome screen. but i can turn off my ipad but not shut down...and i went to my computer and i go to itune. i try to restart my ipad but it say turn off your.find my iphone..but i cant my ipad is freezing.can help me plz.plz help me.................thx u

Option 1
Try force iPad into Recovery Mode. Follow step 1 to 6 very closely.
http://support.apple.com/kb/HT1808
Note: You need to be patient and repeat the above many times to recover your iPad

How to use time capsule for wireless back-up but not internet?

Hello,
I have a tower and recently a laptop at work. The tower is connected to our local network with an ethernet cable and the laptop with wireless. So, the internet connection is fine for both.
I was hoping to use my time capsule to do time machine backups on my laptop. Do you have any advice on how to configure this? I do not want to use the time capsule to extend my Internet, as I believe my work I.T. would prefer to handle all access to their network.
Perhaps there is some documentation about doing this that you could point me to? I have not been able to find it.
Thank you for your help.

Your original question was How to use Time Capsule for wireless back-up but not Internet?
There is no reason for you to connect the tower....or anything else...using Ethernet if your goal remains that same as you stated.
If you are asking if you can backup the Tower using Ethernet, and not wireless, then you can connect the tower to one of the LAN <-> ports on the Time Capsule....not the WAN port.
Yes, it appears to work without plugging into my tower.
Correct, it will work.
I just have to select the network that it created. Of course, I have no access to the Internet while this is happening and it can not auto backup, unless I am on that wireless signal.
As I stated, that is the downside to trying to back up without an Internet connection. You have to establish another network...and backup over that network.
If you are asking if you can stay connected to the work network while also backing up to your non-Internet "private" network, that is not possible.

Airport time capsule showing up as apple tv

airport time capsule showing up twice on my network once as airport time capsule as it should but also as my apple tv, also on my mac or ipad on the airplay button there is a two next to the option to select the apple.

sorry but not sure how or exactly what you mean

Time Capsule shows error message "Conflicting DHCP Range."

I just set up a wireless network using a Time Capsule as the main router with an Airport Extreme bridged to it so I can have a strong signal downstairs. It all worked fine at first, but at some point the Time Capsule showed this error message on Airport Utility: "Conflicting DHCP Range."
The instructions that pop up when I click on the error message are beyond my level of understanding. They say: "This Airport base station rejected a DHCP address in the same subnet as its internal DHCP server. Try switching your Airport Base Station from using DHCP and NAT to bridge mode. If you still want to use DHCP and NAT to share a single IP address, change your DHCP range."
Could one of you tell me what I should do? Thanks.

Try switching your Airport Base Station from using DHCP and NAT to bridge mode.
I suggest that you do what AirPort Utility suggests.....
Open up AirPort Utility, click on the AirPort Express and click Edit in the smaller window that appears
Click the Network tab at the top of the window
Insure that the setting for Router Mode is set to "Off (Bridge Mode)"
Click Update to save the settings and give the AirPort Express a minute to restart

Time capsule wireless works with computer but not other devices.

Wireless internet from the time capsule works with the laptop, but not with any other devices or computers. They pick up the wireless signal, but can't connect. Any ideas?

Thanks for the response. I appreciate any help you can give. The internet modem is from Insight Cable and is an Arris TM602G.
Wireless Mode = create a wireless network
Radio Mode = automatic
Wireless Security = WPA2 Personal
Internet > Internet Connection tab
Connect Using = Ethernet
Connection Sharing = Off
Internet > DHCP tab
DHCP Beginning Address = ? I'm not seeing where to get this info.
DHCP Ending Address = ?
I did notice on the summary that it shows 4 wireless clients, which I assume are the computer and the other devices that can't get the internet but get the wireless.

External HDD (Internal) Not Showing Up In Finder, But It Is Showing Up In Disk Utility

Before I start, I know that this question has technically been solved before, but not exactly in my case. Keep in mind that I'm a graphic designer, this is why I am so passionate about fixing this issue. So, here's the story. Yesterday, I sold my Mac mini (Late 2009). I had plans of buying the new MacBook Pro w/ Retina Display (15 inch), and that worked out perfectly. I bought the MacBook and sold my Mac mini. Prior to selling the Mac mini, I decided to format an old hard drive that I had, which was a 160GB hard drive. My plan was to sell the computer with the 160GB HDD, and keep my 750GB HDD. I know my fair share of computing and repair, so I replaced the hard drive myself, and reinstalled Mac OS X ML on the 160GB HDD. I installed the OS via external SATA to USB connection, and it booted up perfectly through that connection to my Mac mini. Then, when I took out the 160GB HDD, my computer booted to my priority internal drive, which was the 750 GB HDD, that I'm having problems with currently. It booted up perfectly, and all of my information was on it. So, at that point, seeing that everything was flawless, I extracted the 750GB HDD, from inside the computer and replaced it with the 160GB HDD, which I formatted, reinstalled ML on, and was planning on selling it with. The 160GB HDD booted perfectly and everything was working on the Mac mini, but then, I plugged in my 750GB HDD via USB connection, to see if my files and everything was still there, I got a message saying, "The disk you inserted is not readable by this computer" and it gave me three options underneath, which were: "Initialize...", "Ignore" and "Eject". I pressed on initialize, and tried to do everything that I possibly could, without formatting it, and all of the options like "Verify Disk" and "Repair Disk" were "grayed out", if you know what I mean. I tried plugging it into all 5 USB ports, but I got the same message. It was recognized in Disk Utility, but not in Finder. So, I sold the computer with the 160GB HDD that was working fine, but now I had another dilemma which was why my 750GB HDD, isn't showing up in Finder. I can hear the HDD spinning when I plug it in via USB. This Hard Drive has run Mac OS X Lion and Mountain Lion on it, I've never installed Windows on it. So, it was properly formatted for a Mac. Now, I went out and bought the MacBook Pro with Retina Display that I needed, and I tried doing the same thing, which was plugging it in via USB, and seeing if Finder would pick it up. Still, nothing. I ended up with the same message. Here are some reference screenshots, of what I'm getting exactly.
I've called Western Digital, and they told me to try booting up the 750GB HDD, in an older Macbook Pro, to see if it will boot, and recovery all of the files from there. The problem is, I don't know anybody with an older MBP. I called Best Buy and they said that they could take a look at it, but I would truly prefer by fixing this on my own, without having to pay them. That would be my LAST resort. I'm aware that I can't boot up the 750GB HDD in my new MBP w/ Retina because it can only carry SSD. So, I'm basically puzzled. If anybody could help me out, it'd be greatly appreciated. Like I said before, I'm a graphic designer, and I'm in desperate need of the files that were on my 750GB HDD. Thanks.

I describe how you fix it here
https://discussions.apple.com/message/21995208#21995208

Time capsule shows up in finder but I can't connect !!!

Similar Messages

Maybe you are looking for