Time capsule USB printer works when I connect via ethernet but not over wifi

I have a USB printer hooked up to my new Time Capsule. If I turn off my wifi and connect to the Time Capsule with an ethernet cable it works fine. When I try to do the same thing over wifi (even when I'm sitting next to it) it cant seem to make a solid connection. Most of the time it just says Printer Paused, but sometimes it will work, other times the printer just clicks, or starts but then stops. Other than that my wifi connection seeems pretty good.
Is there something with the settings with my older "08 MacBook and the newer Time Capsule?
Any help is very much appreciated,
Thanks

Very interesting one..
Did you upgrade install ML into the MB??
It sounds to me like it has corrupted the wireless drivers.. and I think you will need to do a clean install.
If you have internet working over wireless I see no reason for this to happen though.

Similar Messages

Can connect via Ethernet but not via AirPort

I'm having some problems using my AirPort in Germany. I can connect just fine using an Ethernet cable direct from the modem (NETGEAR DG632B) but when I have plug the Ethernet cable into the AirPort I can't connect. I beleive it has to do with PPoE settings, which I am not really familiar with.
There are three spots I can enter my account info. 1, on the modem itself via Safari; 2, on the AirPort via AirPort Admin Utility; 3, on the Mac via Network Preferences. I have input my PPoE username/password into the modem while directly connected. I would tend to think that this shoudl be it and that everywhere on the LAN side of the modem would be able to utilize that account. The NETGEAR settings page shows the ADSL port Network Type as PPPOE and the LAN port as DHCP, so I have attempted to set up my AirPort and Network prefs using DHCP. That leads to "You are not connected to the Internet. Safari can’t open the page “http://www.google.com/” because your computer isn’t connected to the Internet." Network Diagnostics shows green at AirPort, AirPort Settings, Network Settings and ISP. It initially shows yellow at Internet and Server which lead to "Failed" on both. Network Diagnostics then asks me to choose my network port configuration (Built-in Ethernet, Internal Modem, Airport,Other). I select AirPort and select my AirPort network. Then all the Status lights except for AirPort turn red and asks if I use a DSL or cable model. I select yes, it asks me to restart the device, I do, it asks if I can restart any other devices, I select no. At that point Network Diagnostics says it is unable to connect to the Internet.
I have down-graded to Airport Firmware v5.5.1 as some have advised. No change. I'm running MacOS 10.4.6
My AirPort is just fine as I can use it to set up a LAN with no problem. I even pulled out my old Graphite base station and tried it. Same thing.
I have tried putting my PPPoE account info into my AirPort, my Network prefs both individually and both at the same time. Nothing. Is there something that I'm missing?

You'll need to connect your modem to your AEBS WAN port, configure your AEBS with the Airport Admin Utility, setting up the PPOE to properly log into your modem connection.
You should set up your mac to us DHCP (not PPOE).
THis should allow you to use either the ethernet port or wireless from your AEBS.
I hope this helps!

Can connect via Ethernet but not on Airport

I am able to connect fine with Ethernet. Initially when I brought up Safari it launched the modem and I had to enter my ISP username and password. Then I was able to connect fine with Ethernet. My problem is that I cannot connect with Airport. I disconnect the Ethernet from my MacBook, then I turn on Airport. It detects the wireless modem. I select it. It connects fine, but no internet. I go to the System Preferences, Network. But find nothing wrong. Am I missing something ??? Please advise.

Hi,
You also might want to check that the AirPort doesnt have it selected to have the IP set manually. Always have this detected by DHCP. There should'nt be any problems there, if you are using the Ethernet cable.
Regards
Marc

Can you use Time Capsule as a print server for printers connected via Ethernet or wirelessly?

Can you use Time Capsule as a print server for printers connected via Ethernet or wirelessly?
I know that it works marvelous for printers connected via USB, but I'd like to know if you can use it as a more general print server.

No, you can't, but what do you expect to gain by doing so?
The main advantage of the print server is to provide multi-user network access to a printer that typically only supports a single connection. Since, by definition, your printer already has a network connection and can be used by multiple users.

HT4356 Can I use a 'pc' network printer connected via ethernet to the home wifi network ?

Can I use a 'pc' network printer connected via ethernet to the home wifi network ?
or must the printer I want to use also have a wifi connection ?
I have a home network using ethernet connected devices to a router, also attached to th erouter is a WiFi unit. We are using the WiFi unit to connect to the network and hence to the big wide WWW. We now want to print from our IPads pereferable to our netowk connected HP Officejet Pro 8500 A909a series. (not the wireless model).
I was using the HP ePrint app to print from the Ipad, but I do not fully understand how this works. It seems that you must use the app to do the printing which is fine for basic email and photos, but I can not access the drawing package I have, and want to print from it. Please what is it that I do not understand.

You must use an airprint printer directly connected to wifi through it's own wifi card.
See here for info:
http://support.apple.com/kb/ht4356

My transparency does not work on my iPhone and I was wondering how I fix that? It worked when I first downloaded ios7 but not now.

My transparency does not work on my iPhone and I was wondering how I fix that? It worked when I first downloaded ios7 but not now.

Hello wilsontot_too,
Thank you for the details of the issue you are experiencing on your iPhone. It sounds like you are not noticing transparency on your iPhone. It may be that you have "Increase Contrast" turned on in your iPhone settings.
I recommend verifying that Increase Contrast is turned off in Settings>General>Accessibility.
iPhone User Guide - Large, bold, and high-contrast text
http://help.apple.com/iphone/7/#/iph73b89c6
Thank you for using Apple Support Communities.
Best,
Sheila M.

Apple Tv (3rd generation) says it is connected (via ethernet), but none of the app, or channels, will work. They all say they are unvailable, try again later. The only thing that seems to work is iTunes. (I live in a dorm if that helps)

Apple Tv (3rd generation) says it is connected (via ethernet), but none of the app, or channels, will work. They all say they are unvailable, try again later. The only thing that seems to work is iTunes. (I live in a dorm if that helps)

Its not properly connected to the network. Most school networks require login via webpage, which isn't possible as ATV has no browser. You will need to contact the IT dept or the network provider.

Powerbook G4 can't connect via ethernet but connects via airport

We have a small office network connected to an Efficient Networks DSL router that's managed by our isp. The router has 4 ports and a linksys 8 port switch is connected to one of those ports. Another D-Link wireless router/switch is connected to another port.
2 i-macs connect without problem via ethernet cable. They are set to DHCP and get 192.xx private addresses. Both run 10.4.5. Another older imac running 9.2.2. also has no problems.
I recently purchased a powerbook G4 and it will not connect via ethernet to the Efficient networks router. At first it was connected to the linksys, so decided to connect it direct to the Efficient Networks router. With DHCP, it acquires a 169. internet address which is self generated (i.e. no real connection). I tried to give it a static private address (talking to the isp provider). They could see the powerbook but saw all zero's (presumable mac address). By the way the Powerbook works perfectly at home connected via ethernet cable to a D-Link router connected to a cable modem so it's not a physical problem. I even checked the ethernet cable I used in the office with another computer - no problem.
When I switch to airport in the office, the powerbook connects to the network and the internet. I get some strange warning messages showing the server's and the router's private ip addresses. I click ok, and the powerbook finds an unassigned private ip address. It's the only way it will work, but it causes problems, because I can't connect to one of the network printers. Speed also isn't great.
Can anyone give me advise how to proceed. I am no expert on this stuff so keep it as simple as possible.
Tks

Tim,
Thanks for your help. Here's what I've done before reading your e-mail. The D-Link DI-524 wireless router is connected to the Effiicent Neworks DSL router as you mentioned. One ethernet port of the EFF.Net. router is connected to the WAN port of the DI-514.
Because I have a D-Link router at home which works flawlessly with my powerbook, I decided to connect the ethernet cable of the powerbook to the D-Link which has 4 ethernet ports. Lo and behold, the powerbook acquired a private ip address and connected to the LAN and internet!
When I connected the powerbook direct to the Efficient Networks router, it could not communicate. I believe that there must be some software incompatibility between the powerbook and the Efficient Networks router. By connecting to the D-Link, the D-Link assigned an ip address to the powerbook, and it could connect to the server, lan, etc..
Only problem is that I have a Brother network printer that cannot connect to the powerbook. My powerbook cannot find it on the network. Because there is a linksys switch connected to the efficient networks router's third ethernet port, maybe as you said, going through the D-Link via DHCP (when the Linksys is also acting as a DHCP server, might cause this type of problem. What do you think?
As a final note, other imac G5's connected to the linksys switch (which then connects to the Efficient Network's router) have no problem connecting to the lan or internet and have no problem connecting to any of the printers. When I put the powerbook on that switch, I could not connect to the internet - i.e. whether connecting via the lynksys switch or direct with the efficient networks router - same results: no internet connection whether manually or via DHCP.
So the imac G5 has no problem with the efficient networks router but the powerbook G4 hits a brick wall. The G4 likes the D-Link router. I am concerned (and I will have to check this) that if I turn off the dhcp server feature from the D-Link, that whatever software issue crops up between the powerbook and the Efficient Networks router, will rise up again, because the D-Link will act like a simple switch (just like my linksys switch), and we'll be back to square zero. In any case, no harm in trying. This may be the cause of the Powerbook not seeing that Brother printer (even though it sees another printer and other macs).
Having spent hours reading about network problems, I think it's safe to say that macs have problems with certain routers. Why a G5 works and a powerbook G4 doesn't is beyond me, but clearly software must play a role.

Officejet pro 8500A connected via wireless, but not accessible....

I can t access my officejet pro printer via wifi, after a firmware upgrade last week. I can print however from my iPad, but not from my laptop. Both are connected to the same wireless signal. I can see in my printer and router that both are connected. When I connect the printer via a cable to the router, it works.
As said, I lost this after firmware update.
I tried:
Update the software on my laptop : no Improvement
Switch on/off the router, printer, laptop : no improvement....
Can anybody help? Would a downgrade offirmware help? Anybody familiar with this problem?
Laptop : W7-64

The workgroup shouldn't matter. It's strange that the printer will communicate with the laptop as long as one of them is connected via Ethernet to the router. It shouldn't be doing that at all. It has to be something in the router. I know you mentioned using a different router and it worked just fine. Problem is I'm not sure why this router isn't working right. I'm sure the printer is out of warranty, which is why I'm sure you came to the forums first, but you may need to contact HP tech support. They should be able to remote in and find the setting that's blocking communication. II'll link the information to get in touch with them below. The link will take you to a form to fill out. Once you fill it out and it is processed, it will give you the printers warranty information, a case number, and the phone number to call.
HP Technical Support Case Call Form
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Connect via ethernet but wireless for internet

I don't know why, but my apple tv seems to have forgotten how to connect to the internet and I can't make it remember, lol. Now I will stress, this used to work, and I don't know why it suddenly doesn't work anymore...
Basically I have wireless set up at home for the internet. However, I connect to my apple tv via direct ethernet cable between my imac and the apple tv itself. I have set up internet sharing in preferences to share my airport connection over ethernet, which my apple tv used to be able to use ok to connect to the itunes store/you tube, etc. However, it now can't. I had some trouble with it this morning where it wouldn't connect to the ethernet network at all, although it now does. However, it no longer uses the iMac as it's router and I can't seem to figure out why. Can anyone help?
Thanks!

Chris Johnson2 wrote:
We have one MBP (10.5.8) that is able to connect to our network via Ethernet and use all services. But, when it connects via Airport, it will connect to the wireless router, but will not connect to the Internet or the network...
You might try the three suggestions in the second message of this thread:
http://discussions.apple.com/message.jspa?messageID=10445592

My mac mini will connect via airport but not via ethernet.

I have had a mac mini for several months which I connect via ethernet because it is in a part of my house where the wireless signal is poor. I changed ISP and now I can connect to the router wirelessly but not via ethernet. This doesn't seem to be a problem with the network as the connection works when I connect it to my mac book. Firewall is turned off. There were no major changes to the router settings other than changing the ISP login codes.
Any ideas? Is this a configuration issue or a hardware problem?

Hi Mick,
If your router only supports 10/100 ethernet then it is possible that the auto-detect feature is not working properly to adjust to that speed. The mini has a Gigabit ethernet port. The OS by default sets the port to automatically negotiate the rate but it does not always work and the result is the problem you are having.
To fix it you wlll have to manually set the rate to 100.
To do this, open your system preferences, Select Network. Highlight the ethernet port on the sidebar, click the advanced button. Click on the Ethernet Tab, set the configure pop-up menu item to 100baseTX and click the ok button. If all works out you should see that the Ethernet port icon should turn green.
Hope this helps.

My birthday calendar works on my computers and iphone, but not my wife's ipad. What to do.

My birth calendar works on my computers and iphone but not on my ipad.

How did the MP3 files get onto your iDevices Ii they're not in iTunes?
The simplel rule is: Anything in iTunes can be synced to your devices, but no music files on your devices, except your purchases, can be synced to your computer.

Will USB devices work when VPN connected?

My university internet connection requires an authenticated PPPoE connection followed by a VPN. When I used to use my AirPort Express, I left it on automatic and made both connections from my Mac quite successfully. BUT ... when the VPN connection was made, I lost access to the USB connected printer and the AirTunes connection. I'd like to know if I'm going to run the same risk with an AirPort Extreme. I'd like to connect up a hub with two hard drives and a printer, but if I'm not going to be able to access them when I'm connected to the uni network, I won't bother spending the money.
Thanks in advance for any insight!

I would guess that the same thing will happen. You will lose access to local devices when your Mac is connected through the VPN.

Time Capsule don't work when change base station password

Hello.
I bought a Time Capsule in 8th April 2010. In August 2010 it begun report problems (the message "Finishing backup..." always appeared and backup never ended, beyond Finder crashed all time with the pop up message error - 10810).
In January of this year, the device just didn't worked. Actually, when it turned on just the Airport function worked. In 29th of that month I receive a brand new TC after I went to technical support.
But, in 17th April 2011, it just didn't worked. At all. And, for my bad, at this time, the garantee was expired.
What I did? Well, I restarted it with default configuration (many times) until can access the hard drive. Even erase the disk (after restore some backups when I had the chance).
Well, after this, It works again. But the TC base station password now can't changed.
Actually it can be changed. But, if I do this, the TimeMachine don't get make HD TC's avaliable. And I just don't know why.
I say this because after I restored, manually, the base station password to this default settings (password "public", without quote), it returned works normally.
But I want change this password, because all my backups will be visible for that one's that have a Mac and access my TimeCapsule device.
I think this product is the greatest Fail of Apple. Many people reclaims about it, mainly for its short life and overheating.
Anyway, if there is any people that could help me, I'll appreciate!
I'm brazilian and I'm not so good in English. So I could make some grammar mistakes. Sorry about that.
By the way, if its possible, that one's that answer my question, please, don't use many slang.
Thanks

The screenshots are here https://twitpic.com/4yeock and https://twitpic.com/4ytaks. Sorry for delay!
By the way, after I change the password for grab these screens I can not access my TimeCapsule HD again.
I'm trying (and trying, and trying, again and again) access it after restore to the default settings, but I haven't any sucess.
Ah. Now a message, like this "You are with the device default change. Are you sure keeping this?", appears when I try modify just the network password (keeping the original password device, that is "public").

Time capsule connecté via ethernet et non en wifi (prend du débit)

je souhaite connecter ma time capsule en filaire (ethernet) car en wifi, ca me prend bcp de débit
merci

Hi, Nubz!
Yes, I just saw that, and am still chuckling.
Maybe that will mollify the Jive gods?
Thanks again,
Jim

Time capsule USB printer works when I connect via ethernet but not over wifi

Similar Messages

Maybe you are looking for