Time Capsule wireless connection through Netgear connection

I am now using a Netgear N300 Gigabite modem/router as my main access point (internet et al). However, I want to continue to use my Time Capsule as a wireless drive.
I'm not sure what I should set the Netgear and Time Capsule so that the Time Capsule does not interfere with the Netgear internet connection. Right now that is what it is doing. I have to set the Time Capsule to bridge and connect to it separately.
So, is there a way to access the TC hard drive through the Netgear wirelessly?
i.e. with my laptop I want to stay connected to the Netgear and have internet access but also be able to connect to TC through that Netgear connection.
I don't want to ethernet the TC to the NG. I have my TC ethernet connected to my iMac. So I need to have the NG and TC cooperating wirelessly.

James,
You need to configure the Time Capsule to "join" the wireless network that is being provided by the Netgear router. The Time Capsule will connect using wireless only in this type of configuration.
Then, the Netgear, Time Capsule and your computer will all be on the same wireless network and you will not have to "switch" networks to access the Internet or back up to the Time Capsule.
Before we make any changes, we want to make sure that you understand that the Time Capsule will not perform any routing functions when it is configured to "join a wireless network".
The Ethernet ports on the  Time Capsule are not enabled in this setup, therefore you will not be able to use Ethernet to back up to the Time Capsule. Backups will be over wireless only, which is significantly slower than an Ethernet connection.
This setup can be tricky because you must know the exact type of wireless security that the Netgear router is using in order to provide the correct settings to the Time Capsule.
If the Time Capsule does not receive the correct settings during setup, you will receive a message that there has been an error and you must start all over again with a complete factory default reset of the Time Capsule and try again.
So, before we go any further, we need to ask....what is the exact type of wireless security that your Netgear router is using?

Similar Messages

  • How to connect Time Capsule wirelessly (without hard wire connection)

    Okay, so just bought a Time Capsule, and in the process of setting it up, I am being told by Airport Utility that I need to hardwire the TC to my wireless router in order for it create a network.....
    My question:  Is there anyway around this?  Is there anyway I can create an extended WiFi connection thru the TC without hardwiring?   I have a wifi extender (NetGear universal wifi range extender WGN3000) and was hoping that TC would connect to it and act as a second extender relay.
    I hope my question is clear.
    Also, is my understanding correct that if the TC is not hardwired, and it does not possess a wireless connection, then in order to backup my computer, I must connect to the basestation in Airport, and during that time I will be unable to use the internet??
    THanks!!

    We always say to people do the first backup by ethernet anyway.. wireless takes far too long.. once you are just doing incremental then it is ok by wireless.
    But wireless halves in speed for every hop.. so make sure there is only ever one wireless link between the TC and the computer if at all possible. If you join it by wireless to the network.. you will have no gain.. and lots of pain.. plus half what are already poor speeds.. so you may as well just connect to the router by ethernet.. and bridge the TC.. you can then also setup wireless .. particularly 5ghz which the rest of your network probably doesn't use so you have a faster than normal link both to internet and TC for backup.. when you are in the same room.. link at 5ghz gives great speed and poor range.. go more than one room away and it will generally fall away to nothing.

  • Time capsule wireless router can not connect both Macbook and iPad

    Currently my new time capsule can only connect my macbook pro wirelessly or by ethernet. My iPad or PC can not been connected to it. I guess the setting for the router is something wrong, but I do not know how to fix it. The settings indicate that there is no DNS address, and the router is off (bridged). I tried to change the router setting, but does not succeed. Sincerely ask for help.

    The settings indicate that there is no DNS address, and the router is off (bridged). I tried to change the router setting, but does not succeed. Sincerely ask for help.
    Sorry but I need you to clarify.. router is off.. what router are you talking about??
    If the clients do not have DNS, have you tried just supplying the standard google dns ie... 8.8.8.8 (very lucky number for Chinese) or 8.8.4.4
    http://code.google.com/speed/public-dns/
    You can usually set dns manually whilst still using DHCP for IP address.
    But better to start again.. reset the TC..
    Give it a simple name .. no spaces.. all alphanumeric.. the default name is NOT windows networking valid.
    eg I name my TC.. TC1
    Wireless name.. same rules.. I use TC24 and TC5 (I use separate names for 2.4ghz and 5ghz as I do not want computers auto swapping bands) I also set channels manually.. again because I do not want them auto swapping channels.
    Wireless passwords.. same rules.. you need to make it a bit longer of course.. but pure alphanumeric no spaces.
    In the disk area, assuming you want disk access.. then put in the WORKGROUP name.. usually WORKGROUP.. in caps btw.
    If you do all that it will usually also work with iPad.

  • Computers connecting to internet via time capsule are reporting no internet connectivity.  PC is reporting default gateway has changed.  How to I correct this?

    Am having trouble with maintaining a stable wireless network via the Time Capsule.  Am running 1 Mac and 3 PC on a Time Capsule wireless in bridge mode connected to a Verizon wireless router.  Verizon wireless is turned off and the Time Capsule seems to be staying connected to the Verizon router.  When any of the connected computerss goes to stanby, they often report the internet is no longer available.  The PCs say the default gateway has changed ans the Mac simply reports the network parameters have changed.  What do I need to do to the Time Capsule to stabilize the wireless network?

    It is unlikely that the gateway changes.. but anything is possible.. sorry I am not in the US.. is your service adsl or cable?? What sort of lease time does the public IP have? Some cable companies now rotate then on the hour I noticed.. others on about 3months.. but most it is one day.
    Track it yourself.. see what gateway address the TC gets and if it is rotating with the IP.
    If your client computers are running Mountain Lion.. the plain fact is, they are not particularly stable.
    Wireless is worst.. ethernet tends to be ok.. but for instance Laptops updated to Mountain Lion can be pretty flakey.. with the TC.. and it is the combo that is more the issue. People report improvement with clean install of ML. BUT there is still a bug there that causes the ML to be less than fantastic.
    I experience it occasionally even with a dlink wireless router.. after a wake from sleep.. the network will drop out and need to be manually connected back.. I have to admit I expect no better from Mountain Lion. I could load Snow Leopard on it and it would drop once every blue moon.. but I got the laptop with ML so I live with it.. !!

  • Mac connects but PC won't connect to internet via TIme Capsule wireless net

    I have my personal Mac and work PC at home. I'm switching from a wireless network using my airport extreme base station to a new time capsule. Had no problems earlier, but now with my new wireless network I have the following problem:
    - Both Mac and PC are able to connect to my home wireless network created through Time Capsule
    - Only Mac can access the internet via the Time Capsule wireless network
    - PC connects fine to the wireless network, but the settings indicate the internet cannot be accessed
    I've tried fiddling with configurations etc. but cannot seem to get the PC to connect through to the internet using my Time Capsule.
    The PC will connect directly to the net if I plug in the ethernet from my cable modem....What's the problem? Any ideas?

    Welcome to the discussions forum AZR-DC.
    The PC will connect directly to the net if I plug in the ethernet from my cable modem...
    Make it a habit to power down your modem whenever you connect something different to it. Merely detaching the AEBS and attaching your Time Capsule or your computer directly will confuse most modems, so leave it powered down for a few moments. Power down your other equipment while you're at it.
    Then, power up all the equipment as follows:
    Modem... wait a few moments for it to complete its startup sequence.
    Time Capsule. Wait a few moments again.
    Computers.
    Be sure your PC and your Mac are getting their addresses "via DHCP".

  • Time Capsule wireless connection to DGN1000

    Hi there, what I'd like to do is... Connect my Time Capsule (upstairs) to my Netgear DGN1000 router (downstairs) wirelessly! Therefore increasing my wireless range, and allowing me ethernet ports upstairs, instead of sharing my Macs airport connection via ethernet.
    Thanks, Adam

    It's also quite a long distance for an ethernet cable
    the ethernet cable will work fine for 100M.. and I doubt it is that far.
    In the end the actual cost to install ethernet between two levels of the house can be well repaid with reliable connections.. and fast. Everything else.. whether wireless bridging or EoP are simply trying to do what ethernet does but less well.. less fast.. less reliably.
    After trying wireless repeaters and bridges doing video streaming.. for ages.. and getting it to work really well.. until the gremlins get in.. ie it runs perfectly for 49 minutes of a 55min show and will then begin to glitch.. It was like clockwork.. if the show was a 2 hour film it would not glitch until 1hour 50min. Running ethernet fixed it permanently.. then you can just plug in wireless AP at those points you need wireless.
    The hassle for people who rent though is not being able to do this so EOP is the best alternative.. and work well generally but still depends on the standard of wiring.. and type of breakers used in fuse box if they are on different circuits in the house. As Bob says.. make sure the store allows returns if they don't work well or at all.

  • I want to connect an Airport Express via WiFi to my internet connection and then connect its LAN port to the WAN port of a Time Capsule. Will then any device connected to the time capsule wirelessly be also connected to the internet?

    Background is I can't hook up my time capsule directly to my internet connection via network cable. I tried to extend the network via Wifi, but that did not work. At the moment I have two wireless networks, one with internet connection and another one with my time capsule. So to use time machine I have to change my network all the time.
    Can I buy an Airport Express, use is as a client to my internet connection wifi and provide that connection via network cable to my time capsule and all it's wifi clients?

    The AirPort Express will connect to your existing wireless network if the network is using WPA2 Personal or WPA/WPA2 Personal wireless security settings.
    So, it can join the network as a client and then provide an Ethernet signal to your Time Capsule.
    Be sure to configure the Time Capsule to operate in Bridge Mode so that it will be operating on the same network.

  • I created a wireless network with my Time Capsule but would like to connect this network to a WiFi Hotspot for Internet Access

    I have created a Wirelss Network at home with the Time Capsule and would like to connect this network to the Internet.
    I can't use LAN Cable to connect to it anything becasuse I usually use the WiFi that runs through my building.
    Can I connect the Time Capsule to the WiFi hotspot somehow so that all computers on my network have Internet access and if so, what do I need?
    I need this done because the computers can only be connected to either the WiFi network or to my Time Capsule Network at any given time.
    Or is there a way to be connected to both networks simultaneously?
    I have two PC's and two Macs.
    Thank you for any support and I apologise for my ignorance. I am not too good with networking.
    I have tried the silliest of things like connecting a router to the TC only to then realise that the TC had an inbuilt router.
    I tried connecting a USB WiFI adapter to the USB Port on the TC but it doesnt detect it that way apparently.
    Please help!

    I have a kinda same problem @ https://discussions.apple.com/thread/3531642
    Please reply (somebody)!
    JeremyZ

  • HOME HUB AND TIME CAPSULE WIRELESS CONNECTION

    hi,
    i have recently moved house and have BT broadband and Sky TV. The point where the master socket comes into my house is in an upstairs bedroom, well away from my living room where the TV is... So i'm wondering if its possible to have the Home Hub in the bedroom and then connect my apple time capsule wirelessly to it, then run ethernet from the TC to my Sky box for downloading TV etc. I may need to move the BT master socket to the living room, but hoping to find a workaround.
    I have read some of the forums about bridging etc, but im not sure if this will solve the issue.
    Any help would be appreciated!
    Cheers

    Since you, effectively, have two routers in series you will want to reconfigure the downstream router (the TC in this case) as a bridge to allow the upstream router (BT HomeHub) to continue to provide both NAT & DHCP services for all wired & wireless clients.
    To set up the Time Capsule (TC) as a bridge, either connect to the TC's wireless network or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN port of the TC, and then, using the AirPort Utility, change this setting:
    Internet - Internet Connection tab
    o Connection Sharing: Off (Bridge Mode)
    o Click Update to apply the new settings.

  • HT1695 My new iPad with Retina Display is not able to connect to the Wi-Fi of my new Time Capsule. It used to connect, but now it just spins and spins and never connects. I've tried rebooting everything many times.

    My new iPad with Retina Display is not able to connect to the Wi-Fi of my new Time Capsule. It use to connect, but now it just spins and spins and never connects. I've tried rebooting everything many times.

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Configuring the time capsule airport wlan function as "connect to wlan", the time caspule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport Express it worked!

    Configuring the time capsule airport wlan function as "connect to wlan", the time capsule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport express it worked, the single Ethernet port got the IP Parameters passed through!
    My setup is a Vodafon Esaybox connected to ISP. Time Capsule is not able to extend the wlan of the easybox, neither airport express can do.
    Only the option "connect to wlan" is succesful.
    With airport express I was able to connect my Sony Bravia TV to the lan via ethernet to stream pictures, the TV set got an IP adress from the easybox.
    With the time capsule the easybox dosn't find devices connected to the ethernet ports to submit IP adresses. The TV set get another IP adress (169.xxx.x.x.) in subnet mask 255.255.0.0 and I don not now where from.
    My notebook is a MacBook pro.
    Any idea????
    Thank a lot in advance!
    Kind regards
    Ingo

    Neverthe less, could there be the chance, that this feature could be implemnented with an firmware update?
    That would appear to be a question for Apple to answer. You can make suggestions to Apple here:
    Apple - AirPort Extreme - Feedback
    If the AirPort Extreme and Time Capsule are configured to "extend a wireless network" they will provide additional wireless coverage....and...the Ethernet ports are enabled in this type of setup.
    The "catch" here is that you must have an Apple router providing the network to be extended.

  • Time Capsule & ADSL Modem - Losing Internet Connection

    My ISP is Earthlink which I access via a DSL connection. I use a Zyxel P-600 series ADSL modem to connect and recently purchased a Time Capsule to replace a NetGear router & separate network drive. Since installing time capsule, I've been losing connection to the Internet. I have the Zyxel set in "bridge mode" so there should be no interference with TC acting as a router. I also was experiencing disconnects with the NetGear router but not as often. Ideas?

    How does the computer connect to your internet connection??
    What type is it? Modem? Router? Wireless? ADSL?
    You are not giving away any information. We need something to work with.
    TC are designed to plug into a modem or router by ethernet. If you have wireless only internet they can join the network but it kills the functionality down to slow useless wireless client.

  • Time Capsule Hangs with USB Drive Connected after installing 10.5.6 update

    The 10.5.6 update basically made my External USB Disk connected to the Time Capsule unusable. I've repaired the permissions as suggested in other posts - this did not fix the problem.
    I was unable to perform any incremental backups initially after the 10.5.6 update, so I archived my sparsebundle and created a new one by doing a full fresh backup - which completed successfully. However, after the backup, I was unable to connect to the Time Capsule or the USB drive connected to the Time Capsule via Finder - when trying to connect, my computer hangs and I'm forced to do a hard restart of BOTH my computer AND the Time Capsule, if I just restart one or the other the problem persists. If I let the connection attempt run long enough I get an "Error Code: -8072" message and still have to do a hard restart. After the hard restart of my computer and Time Capsule I'm able to connect to the Time Capsule and the USB drive connected to Time Capsule just fine. However, once the Time Machine backup runs again - the same problem returns, I can no longer access the Time Capsule or the USB drive connected to Time Capsule via Finder and have to do a hard restart of BOTH my computer AND Time Capsule. This 10.5.6 update has been havoc, anyone have the same troubles or ideas for resolving this? Before updating to 10.5.6 my system was working flawlessly with Time Capsule and the connected USB drive.
    UPDATE: I've just verified that this problem only occurs with my external LaCie Hard Drive connected to Time Capsule via USB. If I disconnect my LaCie Hard Drive from the Time Capsule and restart the Time Capsule everything works fine (backups, access to Time Capsule Disk from Finder). If I connect the LaCie Hard Drive via USB to the Time Capsule, I am able to access the LaCie Hard Drive in Finder UNTIL the next Time Machine backup. After the first Time Machine backup with the USB drive connected, I can no longer access the USB drive from Finder - Finder hangs and eventually produces "Error Code: -8072". If I disconnect the USB drive, then plug it back in - Finder no longer hangs and I can access the drive connected to Time Capsule until the next backup occurs.
    Anybody have ANY ideas? This worked fine before the 10.5.6 update!

    I am having a similar problem. Never tried it before installing 10.5.6, but have a Time Capsule (500GB) with a 1TB WD MyBook Essential Edition connected via USB. Hardware is password protected by authorized users of network and needs separate login to access. When I initially set it up, it worked fine (though too difficult to set up). The WD storage drive showed up in Finder window as a subset of the Time Capsule after clicking on the Time Capsule icon. I had an "-8072" error message yesterday that I ignored, but then the file contents of the WD storage drive took forever to be viewed in Finder (though video files could be accessed wirelessly). Today started having a problem... coincidentally?... after a Time Machine backup, and got the message: "The operation could not be completed. An unexpected error occurred (error code -8072)." Now I am unable to get into the WD drive when I click on "Connect As" on the Time Capsule icon in the Finder menu... I just get the -8072 error. I no longer even see the Time Capsule disk as a subset of the Time Capsule icon in the Finder Toolbar.
    What is going on???

  • Can the time capsule works without WLAN cable connected to my DSL router?

    Cna the Time capsule work without WLAN cable connection to DSL router?

    WLAN is usually used for wireless LAN .. plainly you mean WAN port ..
    How do you expect to get internet if the TC is not connected to the internet?
    The TC can work stand alone.. true enough but that will then involve considerable issues in setting up two different IP addressing regimes .. you can just bridge the TC and use it as WAP and switch plus hdd without having to route.

  • I just bought a time capsule and it will not connect to preexisting home WiFi.

    I just bought a time capsule and it will not connect to preexisting home WiFi.  The Airport Utility recognizes one of my neighbors networks but not mine.  I have ATT&T U-verse.  I understand I can use the Airport time capsule as a router but would prefer to use it in my existing network

    tallswag wrote:
    I have a similar hookup, I have a Airport Extreme & Time Capsule. I would like to connect my Extreme to the Time Capsule "6th gen". I would also like to use the LAN ports on the Extreme. Can this connection be done wirelessly or wired? I'm using a Mac Tower that does't have a wireless card if that's important. 
    As long as you have two apple routers then it is up to you which way you do it.
    You can connect them by ethernet and use it setup as roaming network.. for wireless.. it will simply be bridged on the router side. Ethernet is much the faster solution.
    But if you want to use wireless link that is also fine if the range is not too great. Then ethernet to the computer.. so you effectively have a wireless bridge...
    so, Cablemodem----Airport Extreme- - - - - - - -wireless link- - - - - Time Capsule------computer
    Where the more solid lines are ethernet.. that is possible setup. And using the TC directly on ethernet to the computer will keep your backup speed good while also giving you hopefully your full internet speed so that works well.

Maybe you are looking for