Time Capsule Wireless very slow

Hello,
I just installed my TC and it works quite well... but the wireless connection... To do my initial Back-up of 400 Go, it is taking 18 hours... How do I make it work faster?
Thanks

Assuming that you have setup the Time Capsule to create a network, and that it is connected to your modem using an Ethernet cable, temporarily connect another spare Ethernet cable from your Mac to one of the LAN <--> ports on the Time Capsule.
The backup will go 5-6 times faster this way. Once the initial backup is done, you can disconnect the Ethernet cable and use wireless for incremental backups, which should only take a few minutes on each pass.
However.....if you configured your Time Capsule to connect to your network wirelessly, then the Ethernet ports are not enabled on the Time Capsule, and you will need to backup using wireless.

Similar Messages

Time capsule is very slow on wired Ethernet - tested from multiple sources

I purchased a 2 TB Time Capsule today. I want to use it for automatic backups of my Macbook, and I also want to use it to store files from my Windows PC's.
My TC is connected to my network using wred Ethernet only (Wireless is disabled in the TC)
My problem is that transferring files to the TC is incredibly slow. I have been doing some research and found lots of articles that talk about wireless interference and various problems with interoperability between WiFi flavors. None of these would seen to apply as I am using only wired Ethernet to transfer my files.
I also found a couple of discussions that describe how to make a change to the Mac's TCP/IP configuration to avoid a strange network condition slowing things down. This solution doesn't seem applicable as I am seeing the performance problem regardless of where I copy files FROM (I have a mixed environment with Windows and Linux and Mac systems)
Also, I am aware that the inital backup with Time Machine will be slow but I don't think that's relevant to my situation.
My TC is configured for file sharing so I can read and write files from my various Windows systems on the network. When I copy a set of large files to the TC, I see a typical transfer rate of 5 - 6 MB / Second. To me, this is completely abnormal and here is why: When I copy the same files, from the same Windows system, to a server on my network I get about 60 MB / second or about 10 times the transfer rates.
The TC is running firmware 7.4.2.
What gives?
Message was edited by: 92656iPhone

I also had the same issue. My Time Capsule was connect to the Linksys router WAG325N. I had a wireless network broadcasted from the Linksys and a different one from the Time Capsule. When connected to the TIme Capsule wireless network i pinked the Linksys router and got 10% to 30% pack loss. When i pinked the Time Capsule i got 0% loss. I used the AirPort Utility and changed the "Internet" "Ethernet WAN Port" from automatic to "10 Mbps/Full Duplex" and this seem to fix the slow internet.
I guess the Linksys and Time Capsule as issues with port speed negotiation.

Time Capsule became very slow

Hello all,
Yesterday I decided to connect my time capsule (1tb) to my mac mini with an ethernet cable (cat6) instead of the wireless setup I have been using for quite some time. At first the transfer rate was high, as I expected, but then after an hour or two it became immensly slow. A file from 50mb would take over 30 minits to transfer from my timecapsule to the mac mini and vice versa.
I changed the timecapsule setup throught the airport configuration tool, but the only thing increasing the speed was to change the setting for the ethernet - wan - port to 1000 mb/s, however this ended in high transfer rates but I could no longer connect to the internet.
I started looking for solutions on the internet but all solutions did not solve my problem.
I changed the ACK from 3 to 0 without any results...
So that is why I posted this topic and I am desperately looking for help...

Are you reusing an old backup? That can be very slow.. you need to create a new backup for the new computer.
You need to figure out is this a general wireless issue.. or is it the TC just getting old.. a Gen2 is well past useby date.
Look at A1 here. http://pondini.org/TM/Troubleshooting.html
Or is that what you have there. Doesn't look like what I see in the Log.
Test by copying a single large file to the TC.. say 1GB and checking the speed. If that is fast. then you need to figure the old backup is not working well.
Also test with an ethernet connection so you can determine the issue is wireless or not.. when you test with ethernet shut off the wireless so it is not going to have two paths to the same destination.

Time capsule wireless so slow with one Macbook but not other

We have a Time capsule network set up to run at 5 GHz, and (out of necessity because of the problems) an older wireless g access point running in parallel.
One macbook running Leopard gets good speed when connected to the 5Ghz network, as does the Apple TV, which can also stream almost flawlessly by airtunes to an airport express connected to a hifi.
However, if I try to connect to another macbook (still running Tiger) to the time capsule network (even with the other components switched off) then the connection is frequently really slow, such that the web becomes unusable and it is impossible to reliably stream to the express or ATV. However, if I switch to our old g rated wireless access point connected to the same router as the Time capsule then I get a much higher speed connection, although airtunes still intermittently drops sound, but I can stream an HD movie to ATV with no problem.
Why is one Macbook fine but the other is so slow on the 5Ghz network?

Glad to see the overwhelming response to my post : )
Anyway, I have upgraded the OS to Snow Leopard and the 5Ghz network seems to have speeded up considerably on this macbook. Perhaps it was a problem with Tiger.

Restoring Time Machine backup from Time Capsule. Very slow times solved

For me at least . .
Like many people it seems, I have had enormous problems trying to restore data using Time Machine on a Time Capsule. The data had been backed up fine. The problem was the time for restore which initially was projected at 125 hours for 235GB. Reality suggested that (after 24 hours) this estimate was going to be about right and clearly unacceptable.
I cancelled the backup and read as much as I could across bulleting boards.
The main impression was of a howl of frustration from the many people who had experienced the same problem.
The collected actions below were assembled from many threads and ultimately ended in success. I hope they help.
My initial setup was as follows:
PowerMac G5 Power PC (2005) with 8GB DDR SDRAM (1000BaseT Ethernet connector). Mac OSX 10.5.8
1TB Time Capsule on Ethernet network via a 100BaseT Hub.
I was restoring to a 1TB USB 2.0 Seagate External Desktop Drive (ST3100005EXD101-RK) attached via a USB Hub to the G5.
Having read some threads, I did all of the following:
• I brought the TC into my home office and connected it directly to the Ethernet Port of the G5 to allow the most direct connection from TC to G5
• As suggested in one thread, I replaced the Cat5 ethernet cable I was using with a Cat5e cable (Cat6 is better) to allow 1000BaseT connection to the G5.
• I turned off Time Machine backups and MobileMe Sync.
• I terminated all unnecessary applications the computer
I restarted the restore and the result was the same.
I read more widely and then did the following:
• I reformatted the Seagate target drive using GUID and Mac OS Extended (Journaled). (Applications>Utilities>Disk Utility>choose top level of target drive>Partition>choose number of partitions under Volume Scheme (1 for me)>Options (button under partition window)>GUID Partition Table>Apply and wait quite a while. I had originally had it as Apple Partition Map and GUID was recommended on one particular thread.
• I plugged the target USB drive directly into the USB port on the front of the G5 to eliminate the hub as a potential cause of the slow data transfer.
• Readings suggested that Spotlight might be trying to index one or both of the TC and the target drive. To prevent this the author suggested adding the TC unit and the target drive to the Privacy tab of Spotlight (System Preferences>Spotlight>Privacy. Click + at bottom of window and navigate to target drive/s to add). Activity monitor showed as much data being sent as received so this seemed a likely contributor to the problem. I added both drives as described.
• Somewhere it was mentioned that IPv6 might be causing the problem. I turned it off (System Settings>Network>Built-In Ethernet>Advanced (bottom right of window)>choose “Off” in Configure IPv6 drop box.
• I unplugged the Internet connection from the TC to ensure no chance of this being a factor.
• My G5 doesn’t have an Airport but if you do you should also turn this off. You want to be quite certain that there are no connections that either the computer or the airport can channel data through other than the Ethernet cable.
• I don’t have anti virus software but this should also be turned off as it seems this was slowing down data transfer for many people.
• I shut down the G5, the USB target drive and the TC and restarted them all. After start up, I once again shut down all unnecessary programmes.
I restarted the Restore and, after the customary long wait as it added up all the files to transfer, it announced that the restore would take 4 hours (as opposed to the five days it had suggested previously).
Activity Monitor now shows data transfer rates of 17mb – 18mb per second and it looks like 4 hours is going to be about right. It also shows large amounts of data being received but now with negligible amounts being sent.
I’m afraid I don’t know which of the above is the bit that solved the problem. It could be a combination but I believe that if you do all the above, your restores / backups will all go at an acceptable speed.
A last note to thank all those individuals whose wise words I scoured for these instructions. I hope their collected suggestions are of some use to others.

The migration assistant or the original backup?
I tried WiFi, Ethernet and on the second attempt with a fresh backup on a USB drive.

Time Capsule wireless working slow on PC's

I've had a Time Capsule for right at a year and it has worked perfect. All of a sudden, a couple of days ago, none of my PC's will connect to the internet or email. They say they are connected to the network, but when trying to access internet or email it's a no go. I've tried resetting my Time Capsule to no avail. My iMac, iPod, and my daughter's MacBook Pro connect to internet and email with no problem. Has something changed all of a sudden?

I am also having problems with this. My PC netbook shows that it is connected to my TC wireless network with an "Excellent" connection, but I can never actually access the internet. The netbook also recognizes the Time Capsule itself as a wireless hard drive- since I have installed AirPort - but when I try to connect, it says my password is wrong.
Please help.
L

Time capsule running very slow under OS X 10.8.5 (12F45)

Having great difficulty completing a back up. So far taken 3 hrs to back up 5gb out of 100gbs

You are not trying to use wireless for backup, are you?
A wired Ethernet connection should take between 3-4 hours for backup. Wireless will be anywhere from 5-10 times or more slower, depending on your particular connection and the capabilities of the wireless devices.

Time Capsule with very slow network throughput

I have a TC that is only supply about 5% of the network throughput it should do.
We ahve a 2MB connection and any computer that is connecting to the TC wirelessly is only getting around 0.1MB. The signal is strong, the noise is low, it's on an isolated channel (no other networks overlapping). It does this regardless of whether I switch to wireless-g or wireless-n (2.4GHz or 5GHz) and regardless of which channel I select.
I plugged in a different TC and I got my 2MB connection no problem.
So I think the first TC is knackered. Luckily it's still under the 90 warrantee. I want to return it to get a replacement, but I can't get through to the apple care telephone service. I've been on hold for 20 mins then got cut off without talking to anyone - this happens every time I call. Why on earth anyone would pay for apple care is beyond me if you can't even get through to Apple!
Can you just take a TC back to an Apple Store and get a straightforward replacement?

Sorted it! I hit the factory reset button on the back and started again from scratch.
There must have been some software issue in the TC itself that could not be addressed through the configuration interface.
I hope this helps anyone who has a similar problem. In summary this is what I was experiencing:
1. When connected Mac Mini to TC with ethernet cable I had top speed access - so no drive writing issues.
2. Set up the TC to share our 2Mb internet connection as a wireless-g network. When connected a laptop to TC via the TC's wireless-g network I had excellent signal strength, low noise, and an uncluttered channel (as indicated by iStumbler) - so no interference issues with other netowrks, microwaves, cordless phones etc.
3. The laptop reported an excellent signal strength and potential rate of 54Mb.
4. Used an online broadband speed tester (www.cnet.co.uk/misc/speedtest) on the laptop to determine the actual throughput. The result was around 0.2Mb. Not good.
5. Tried copying a file from the TC over to the laptop and monitored the throughput using the laptop's performance monitor. The result was still around 0.2MB.
6. Tried changing the wireless-g channel. Same result.
7. Repeated the above with a wireless-n network. Same result.
8. Finally, hit the factory reset and repeated points 2 - 4 above. Got almost 2Mb, which is what I was after!
Hope this helps someone.

Time Capsule Archive very slow... or stuck

I put my TC to archive yesterday to a USB 2T iomega drive... all initial steps went well but later on the next day the TC is still with an amber light and nothing has happened, is this normal, should it take so long... I had about 450 GB of information in the TC so I don't know it this is a lot or not.
Also, is there anyway to know the progress of this archive?
thank you,
eric

Nope that is not normal.
The SOLID AMBER light means that the operating system on the TC is loading... so it's not actually even running when you see that.
Try again - and when you start the Time Machine backup - you should have the time machine indicator up on the finder bar is OSX that spins when it is backing up - click on that - it will give you a real-time progress of the backup.

Time Capsule wireless file transfer - terribly slow until...

I've got a really strange problem with Airport and Time Capsule. Wirelessly copying a file from my MacBook 10.5.2 to Time Capsule is terribly slow - until my screen goes to sleep!
80 MB is estimated to 45 min, and only 2-3 MB is copied in two minutes. When I or Energy Saver turn the display off, the same file is copied in 35 seconds!
I discovered this by accident, but it also explains why my first backup (12 GB) looked like it would take forever, but after both me and the display went to sleep, backup was done in two hours.
Anyone else having the same problem? Anyone having the solution?
Thanks! Joachim

Hi Joachim,
i think it is the same for me. But only when using timemachine not when doing normal file operations. Maybe timemachine is saving bandwith while the machine is not in screen saver mode...
Your machine should not go to sleep mode when a timemachine backup is running
What is your wireless connections speed?
You can see the rate when 'ALT + clicking' on the airport symbol in the menu bar.
Regards,
somi

Can I copy my iTunes files and folders to Time Capsule wirelessly from my PC?

Can I copy my iTunes files and folders to Time Capsule wirelessly from my PC? I was wondering since my iTunes files and folders are connected to iTunes.

You can but the TC is the worst possible location. The design is slow to start and quick to stop data connections.. that will cause trouble.
Moving folders has specific instructions.
http://support.apple.com/kb/ht1364
Move it to an external hard disk fine.. but be very sure you will not be happy with the TC as a location.

Since installation of Mavericks, Time Capsule works very slowly, and the next backup of 236 GM will take nearly 30 days. What can I do to get backup more rapidly ?

Since the installation of Mavericks, Time capsule works very slowly and will need 30 days or more to produce a complete backup of about 200 GB. What can I do to get a complete backup more rapidly ?

What setup is the TC now.. ? what model and what firmware? Maverick seems to need 7.6.4 on the older TC.. and latest firmware on the AC version.
Is it in router or bridge mode? Do not use wireless only.. join a wireless network.
Is the computer connected by wireless or ethernet? I strongly recommend a test by ethernet.. with wireless in the computer turned off. If it is still very slow something is majorly wrong.. but I need the info I asked for to troubleshoot further.

New to Apple and Time Capsule Wireless

I am a new apple customer. I just bought my 1st iMac and I am trying to make the total break from MS.
I have mediacom as my ISP and my present wireless router is a Linksys WRT600n (purchased about 3 years ago). With this system I have had problems with coverage in my house as well as needing to reboot the device often.
The router is located in a 1st floor bedroom and I get spotty coverage in the living room and even more spotty service in the adjacent kitchen. The distances away from the router as the crow flies is 24 feet for the living room (involves 4 interior walls) plus 15 more feet (an another wall) to the kitchen. Since we use our wireless system more in our living room and our bedroom (this is only 12 feet away and 1 interior wall), I have decided to move the wireless router to the living room and place it on top of a entertainment center. My thinking is that it will provide better coverage to the areas where we use it (hoping to use Apple TV in both living room and bedroom).
This leads me to my question: what has been the experience of the time capsule community in regards to time capsule wireless coverage and reliability?
Also, please note that the iMac will be located in the same bedroom where I will be removing the current router and as such, the wireless backup capabilities of the time capsule will need to traverse the same 24 feet and 4 interior walls.
Any feedback will be most appreciated.
Harvey49

The reliability of the Apple Extreme is very good.. TC much less good. 3years is often a failure point for stuff that runs too hot. Like your WRT600N and the TC with its Green Drive and internal power supply.
On wireless range though I would say pretty ordinary. I have tested all the generations of the TC and most of the Extreme.. including Gen5. In my double storey house with an old G wireless modem router (downstairs extreme end).. right near the TC/AE whichever I am running.. from the other end of the house (upstairs) the old G wireless gives more than adequate signal to get full speed internet.. the TC does not.. And 5ghz goes pretty much to the next room and then disappears but that is as expected.
Use the tests here to find what give good range.
http://www.smallnetbuilder.com/lanwan/router-charts/bar/58-2_4-ghz-dn (you can change the chart to give speed in the worst location ie F http://www.smallnetbuilder.com/lanwan/router-charts/bar/58-2_4-ghz-dn?see=P_F
Airport extreme is there. Well down but there.

My MBP doesn't remember my Time Capsule wireless network when waking from sleep

My MBP (OS 10.5.8) doesn't remember my Time Capsule wireless network when waking from sleep. Thus, every time my MBP wakes from sleep, I need to select the Airport icon in the upper menu bar, select "Join other network", enter SSID and password. This is very cumbersome. And, I never had this problem when I was using the ISP's provided wireless router/gateway/DSL modem. Adding the Time Capsule and using it to generate the wireless network has introduced this problem.
It appears that this problem has to do with the hidden SSID. I don't need the lecture on how hidden SSID provides no serious security benefit. That's why I have the WPA2 encryption. I'm interested in a solution that will allow the Time Capsule to generate the wireless network, maintain a hidden SSID, continue to use WPA2 encryption, but have my MBP recognzie and autoconnect to this network.
Solutions I've alread tried:
1. Open Network Preferences
2. Select Airport from left hand column (and ensure Airport is at top of that list)
3. Select Advanced
4. Delete all Preferred Networks.
5. Apply settings.
6. Restart computer
7. Return to Network Preferences and from Advanced page, manually add my network with hidden SSID and WPA2 password
This solution works fine as long as I don't take my computer elsewhere and connect to another network. As soon as my preferred networks list gets another network, my MBP stops finding my TC network. Since I take my laptop to a lot of places (it's a laptop, after all...) this is a problem.
As I say, prior to adding the TC on my network (and using it to generate the wireless network), my MBP had no problem keeping 50+ preferred network names/passwords in the Preferred Network list, but always automatically finding/connecting to my home network without the need to "Join other network." Thus, I assume the problem lies with the Time Capsule.
Any ideas?

LaPastenague, thanks for weighing in. Didn't know that the hidden SSID capability was not IEEE standardized, and thus different devices will handle hidden SSID differently. With my admittedly limited knowledge of how SSID/hidden SSID works, I'm still a little confused as to why my MBP would remember the generic router/gateway's hidden network, but struggle with the TC's hidden network.
To my knowledge, when an SSID is broadcast by a base station (Airport, wireless gateway, etc.), a connecting device (like a laptop, iPad, etc.) detects this broadcast--this would be a passive reception of this SSID signal.
When an SSID is hidden, the base station does not broadcast its identification. Rather, a connecting device must transmit the name, and when the base station recognizes the broadcast, the connection is made. That's what you do when you select "Join another network" and manually enter the SSID.
The idea with OS X's Network Preferences is that these steps, whether for hidden networks or broadcast SSIDs, become automated.
Where is the potential for a different chipset between the TC and the previously used wireless router/gateway to alter this functionality? Shouldn't the selection of an SSID by the MBP to broadcast to seek for a base station be a function solely on the MBP? And once broadcast by the MBP, the TC should detect and reply?
Basically, the MBP can connect to the hidden TC manually just fine. The MBP can connect to the old setup automatically just fine. The MBP cannot connect to the TC automatically. Aren't these automatic connection functions solely on the MBP?
I'll try un-hiding the network and re-verifying that the problem is exclusively with the hidden network.
Z

Extending Gen 1 Time Capsule Wireless network with Airport Express N

I am having difficulty setting up my new Airport Express w/ 802.11N (SKU# MB321LL/A) to extend the wireless network from my Time Capsule (SKU# MB276LL/A).
My setup is as follows:
Time Capsule is connected to Cable modem with the following wireless settings:
Wireless mode -> Create a Wireless Network
Allow this network to be extended -> Checked
Radio Mode ->802.11n (5Ghz N only)
Wireless Security -> WPA2 Personal
The issue is the when I attempt to setup the AE to extend the network. I match the settings to the Time Capsule:
Wireless Mode -> Extend a Network
Select the Time Capsule Network
Allow wireless clients -> Checked
Wireless Security -> WPA2 Personal
However after I reset the AE the LED glows Amber and the following problem is reported:
+Wireless Network+
+This AirPort wireless device is set up to join a specific wireless network that can't be found. If you don't see the network that you want to join in the Network Name Pop-up menu, enter the network name and network password if necessary to try again.+
When I check the Airport->Wireless tab the settings were as before.
Any thoughts on this? Thanks.

Welcome to the discussions!
Have you tried to position the AirPort Express close, say 10-15 feet, as a test to see if it will connect that way?
If so, then move it back another 10-15 feet, etc.
5 GHz signals do not travel well or penetrate surfaces very well, so my first thought was that the signal was not strong enough for the Express to pick it up where you had it located.
Message was edited by: Bob Timmons

Time Capsule Wireless very slow

Similar Messages

Maybe you are looking for