Time Capsule With Non-Bridging Ethernet connection?

Hi all,
I wonder if it is possible to connect the Time Capsule to an existing Ethernet such that it doesn't do bridging between the three Gigabit ethernet ports and the WAN port, but simply acts as if it was a device plugged into one of the "switch" ports, thus being a member of the network with an independent built-in three port switch. However, it still should do bridging between ethernet and AirPort...
Is this possible?
The reason why I'm asking this is that I experience difficulties in seeing Bonjour-enabled devices connected to the LAN ports of the time capsule, because bridging puts a border for broadcast and multicast packages, which are used by protocols like Bonjour (aka ZeroConf, mDNS...). I can access them if I know their IP addresses and the TCP ports the services are on I wisch to use, but certainly it would be nicer to just have them appear in the Finder...

I saw that, in fact, the broadcast / bonjour issues were most likely because of a firmware bug, because after I upraged to a new firmware version, everything worked fine, and the built-in switch showed the expected behavior...

Similar Messages

Time Capsule with (2) AirPort Express connection problem

I have (1) Airport Time Capsule with (1) AirPort Express connected. I'm trying to connect another Airport Express but only get a yellow light on the 2nd Express. If I connect it with a ethernet cable I get a green light. How do I connect a 2nd Express?

The 2nd Express needs to be about the same distance from the Time Capsule as the 1st Express....and....it cannot be closer to the 2nd Express than it is to the Time Capsule.
The reason for this is that the Express will pick up the strongest signal and you want the Express to pick up the Time Capsule signal to be able to extend it.
Then, start over as LaPastenague instructs on the 2nd Express and configure it again.

Set up time capsule with PC using ethernet

Hi,
I have a Time Capsule which I want to use as a wireless router.
I have two PCs - a desktop without a wireless card, and a laptop with one.
My internet connection requires a SecureID password, so whenever it disconnects (for any reason) I have to enter a new password.
To the best of my knowledge this can only be done from the AirPort utility - and that is only possible from a PC with a wireless card.
As the laptop is not always home, I'd like to be able to do this with my desktop, which is equipped with a wired LAN card and does not have a wireless card.
Is there a way to do this?
Thanks,
Omri

Thanks.
I tried it, and the airport utility just said that it cannot detect any wireless apple devices.
In the Time Capsule manual, it also says that the time capsule can be configured either by a Mac with wireless/ethernet or with a PC with wireless.
I solved the problem by buying a cheap PCI wireless card for my desktop.

How do I set up my time capsule with my PC and BT home hub

Hi, I really need help.
I have a new time machine I am having trouble setting up. I have a BT Home Hub that I have hard wired to the TC to the WAN port. I have Connected my PC to the Ethernet port. The PC will not find the TC.
I also need to Wi-Fi attach other laptop PCs to it.
PLEASE CAN SOMEONE HELP?
Ade.

You might have an IP collision ..
unplug the wan connection to the home hub..
Restart the Time Capsule with a single ethernet connection to a pc plugged into its LAN port.
Make sure the pc is getting an ip address. Open airport utility and see if you can now access the TC.. !
When you say PC do you mean windows machine?
Windows can have some issues accessing the TC.. especially if you have the windows computer on win7 running homegroup.. which is a wretched piece of incestous connection between win7 exclusively.

Computers connecting to internet via time capsule are reporting no internet connectivity. PC is reporting default gateway has changed. How to I correct this?

Am having trouble with maintaining a stable wireless network via the Time Capsule. Am running 1 Mac and 3 PC on a Time Capsule wireless in bridge mode connected to a Verizon wireless router. Verizon wireless is turned off and the Time Capsule seems to be staying connected to the Verizon router. When any of the connected computerss goes to stanby, they often report the internet is no longer available. The PCs say the default gateway has changed ans the Mac simply reports the network parameters have changed. What do I need to do to the Time Capsule to stabilize the wireless network?

It is unlikely that the gateway changes.. but anything is possible.. sorry I am not in the US.. is your service adsl or cable?? What sort of lease time does the public IP have? Some cable companies now rotate then on the hour I noticed.. others on about 3months.. but most it is one day.
Track it yourself.. see what gateway address the TC gets and if it is rotating with the IP.
If your client computers are running Mountain Lion.. the plain fact is, they are not particularly stable.
Wireless is worst.. ethernet tends to be ok.. but for instance Laptops updated to Mountain Lion can be pretty flakey.. with the TC.. and it is the combo that is more the issue. People report improvement with clean install of ML. BUT there is still a bug there that causes the ML to be less than fantastic.
I experience it occasionally even with a dlink wireless router.. after a wake from sleep.. the network will drop out and need to be manually connected back.. I have to admit I expect no better from Mountain Lion. I could load Snow Leopard on it and it would drop once every blue moon.. but I got the laptop with ML so I live with it.. !!

Time capsule with Windows 7

Hello,
I have a Time capsule, with one Tbyte disc, connected by ethernet cable to a Windows 7 computer. I cannot open the disc. It says "Disc not accessible, access denied".
It works perfectly with another computer under Windows XP.
Does somebody have an idea?
Also I did not find how to update Airport and Time capssule software.
Thank you for help
Palou707

Just an update to the above i can now no longer see the time capsule in network places!! All i have done is retstarted!!! I can still see the time capsule from my mac and access it!!!

I need to configure my Time Capsule with a Ruckus wireless...

Hi people, i need your help to solve this problem...
I need to configure my time capsule for first time with one Ruckus wireless...
If you can...could you please give me the solution?
Thank you all!

Time Capsule is designed for ethernet connection.. it is not really good without it.
There is a single option to join wireless network.. hidden and unused as it should be..
On a windows version you will have to hold down the alt key i think when you click the options for wireless mode.. it will then offer join a wireless network.
It is super slow.. and subject to easy corruption of files.. it will turn off all wireless AP and routing and ethernet functions.. good luck!!

Can i connect my time capsule with my router as a bridge ?

can i connect my time capsule with my router as a bridge ?

I am a bit lost .. did you work this out?? You are running a second thread.. and answered it with this question.
The TC can be bridged.. plug it into the main router by ethernet and run it in bridge mode.. that is router bridge.
Do you mean wireless bridge??
If you mean wireless bridge the answer is maybe but unlikely.
If you setup the TC to join a wireless network.. it becomes a dumb client not a bridge.
So to get it to wireless bridge you need to use another apple router.. that is the only way to get them to work.
If you want specifics ask specific questions.

Connect apple tv to time capsule with ethernet?

How do you connect apple tv to time capsule with ethernet?

Oh, that's so sad. . Im sorry, but this problem requires professional help. At least I can't help you. Here is a link to Apple - Support - Contact Support.

Configuring the time capsule airport wlan function as "connect to wlan", the time caspule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport Express it worked!

Configuring the time capsule airport wlan function as "connect to wlan", the time capsule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport express it worked, the single Ethernet port got the IP Parameters passed through!
My setup is a Vodafon Esaybox connected to ISP. Time Capsule is not able to extend the wlan of the easybox, neither airport express can do.
Only the option "connect to wlan" is succesful.
With airport express I was able to connect my Sony Bravia TV to the lan via ethernet to stream pictures, the TV set got an IP adress from the easybox.
With the time capsule the easybox dosn't find devices connected to the ethernet ports to submit IP adresses. The TV set get another IP adress (169.xxx.x.x.) in subnet mask 255.255.0.0 and I don not now where from.
My notebook is a MacBook pro.
Any idea????
Thank a lot in advance!
Kind regards
Ingo

Neverthe less, could there be the chance, that this feature could be implemnented with an firmware update?
That would appear to be a question for Apple to answer. You can make suggestions to Apple here:
Apple - AirPort Extreme - Feedback
If the AirPort Extreme and Time Capsule are configured to "extend a wireless network" they will provide additional wireless coverage....and...the Ethernet ports are enabled in this type of setup.
The "catch" here is that you must have an Apple router providing the network to be extended.

How do I connect my time capsule with a Lynksis wi fi netwotk?

How do I connect my time capsule with a Lynksis wi fi netwotk?

You cannot extend or repeat a non-apple router in an apple router..
You must plug it in via ethernet and then setup roaming network (or if you like a completely separate network.. makes no difference from the TC point of view). TC is in bridge mode. That is router bridge not wireless bridge.. I gave the info on the other thread you are running.. very confusing when you ask in multiple threads.

How to use time capsule as hard drive and connect with existing net gear router

I have a netgear D6300 router, which i use to connect to internet - which is excellent so far for my downloads and games etc for my PS4 and hence am keen to continue using it. I bought the Airport time capsule for wireless storage, and when i set it up, I was advised on setup to connect the TC to my router, and it did what it needed to do.
Now, in order to connect to internet, i need to connect wifi to net gear router, but to access time capsule, i need to change wifi connection to my newly created wifi network with TC.
I want to use TC as a backup storage for my mac (its a 3TB TC), but also, my laptop has only 500gb hard drive which is now half full from downloads, so i want to transfer all my downloads to my TC and use it as an external hard drive, and future downloads to TC - but when i connect to wifi of TC, i can copy my folder on my mac, but not paste it to TC in finder. (the only thing in TC is an image of tmg of my macbook from first backup.).
How do i use TC as an external HD - there wasn't much difference in price of external wifi/wireless HD between non-TC and TC at 3gb, so i just thought i'd go for the airport TC option.
And is it possible to keep connected to wifi internet via net gear router, AND wifi TC - the whole point i bought it (from US shipped to australia on eBay, therefore not able to send back) was to use TC as external large HD via wifi, but keep my net gear router going.
Surely there is a way to not having to flick between wifi connections of TC and net gear internet.
When i'm connected to TC, i can't access internet, only TC.
And I don't really want to connect TC to my router via ethernet cable, as too many cables.
This can't be a difficult situation to manage, but i'm not sure how to do it.
Thanks

And I don't really want to connect TC to my router via ethernet cable, as too many cables.
Sorry but you have very little choice.
The TC can join to a wireless network.. but it is flakey, poor, slow and highly NOT recommended way to do things.
Nevertheless if you want to give it a try .. here is the method.
How do I setup my time capsule with wireless internet?
You SHOULD, plug the TC into the Netgear and run it in bridge mode.. you set the wireless to create a wireless network.. then when you connect to the TC it will be also connected to the internet and fast.
(if you don't do that you may as well have used a USB drive plugged into the Netgear, as it would be just as good).
TC is not actually designed for mixing Time Machine backups and files.. but if you are just storing downloads that is ok.. but I strongly recommend you use a DMG or sparsebundle to prevent the TM and the data from messing each other.
See Pondini instructions here.
Q http://pondini.org/TM/Time_Capsule.html

How can I use my time capsule with Ethernet cable? How is it also possible to use time capsule as a normal external hard drive?

My problem is that I don't know how to use my Time Capsule with Ethernet Cable, as when I use wireless it is really slow.

Make sure that there is an Ethernet cable from one of the LAN <-> ports on your modem/wireless router to the WAN port on the Time Capsule
Click on the Wireless tab at the top of the page
Change the setting for Wireless Mode to Off (I assume that you do not want the Time Capsule to provide a wireless network since you already have a wireless network)
Next, click the Internet icon at the top of the screen, then click the Internet Connection tab
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Click the Update button at the bottom and wait 30 seconds for the Time Capsule to restart and display a green light
Then, you must power off your entire network...all devices....in any order that you want
Wait a minute
Start your modem/router first and let it run a minute
Start the Time Capsule and let it run a minute
Keep starting devices one at a time until everything is powered up
If you are using Time Machine for backups, you will need to reset the connection because you have changed the way in which the Time Capsule connects to your network
Open System Preferences (gear icon) on the dock
Open Time Machine
Click Select Disk
Click the Time Capsule to highlight it
Click Use for Backup or, it might be Use Disk
Now you can connect your Mac using an Ethernet cable to one of the LAN <-> ports on the Time Capsule to back up using Ethernet. Be sure to turn off the wireless on your Mac before you start the backup.
If you want to backup using wireless, disconnect the Ethernet cable from the Mac to the Time Capsule and turn on the wireless and connect to your wireless network. Your computer will now backup using wireless.

Replacing an Airport Express with a Time Capsule but it won't connect to the internet.

Hello, I hope somebody can help.
I am trying to replace an Airport Express with a 2TB Time Capsule but it won't connect to the internet, via an ADSL modem.
I have tried everything I can think of, powering down all devices, re-setting all devices, but nothing seems to solve the problem.
When I first tried to set up the Time Capsule, there was an option to replace the Airport Express using the same settings.
But there were repeated error messages of 'No DNS Servers' and 'PPPoE server couldn't be found'.
I also had messages that the password for PPPoE wasn't correct, but when I plug the Airport Express back in again, everything works fine.
What could the problem be?

99% of issues with authentication are wrong password or wrong username.. eg it can be strange like the user name is missing the domain.. whereas the Airport Express works fine without it.
Ring your ISP and make doubly sure you have exactly the correct username and password.
If it still doesn't work, put the adsl modem back into router mode and try it again directly on the modem.. if it works ok on the modem but fails on the TC that is possible and can be caused by pppoe client using incorrect authentication type, CHAP or PAP which the TC does not allow you to select AFAIK.. some ISP do not give enough time to get the router to switch on auto to the correct authentication method.
In the end run the modem as router and bridge the TC. It will work just as well for most installations in bridge as the modem in bridge.

Connecting Time Capsule with switch 10/100

Can I connect a Time Capsule with a Dlink switch 10/100 Wifi?

You can, but devices connected to the D-Link switch will drop to a maximum of 100 Mbps speeds. The Time Capsule supports 1,000 Mbps or Gigabit speeds.
If you plan to transfer a lot of files using Ethernet, the numbers speak for themselves.

Time Capsule With Non-Bridging Ethernet connection?

Similar Messages

Maybe you are looking for